Field-Assisted Densification of Superhard B6O Materials with Y2O3/Al2O3 Addition

B₆O is a possible candidate of superhard materials with a hardness of 45 GPa measured on single crystals. Up to now, densification of these materials was only possible at high pressure. However, recently it was found that Al₂O₃ can be utilized as an effective sintering additive, similar to the addition of Y₂O₃/Al₂O₃ that was used in this work. The densification behavior of the material as a function of applied pressure, its microstructure evolution, and the resulting mechanical properties were investigated. A strong dependence of the densification with increasing pressure was found. The material revealed characteristic triple junctions filled with amorphous residue composed of B₂O₃, Al₂O₃, and Y₂O₃, while no amorphous grain-boundary films were observed along internal interfaces. Mechanical testing revealed on average a hardness of 33 GPa, a fracture toughness of 4 MPa·m^1/2, and a strength value of 520 MPa.     

Reactive Hot-Pressed Alumina–Boron Nitride Composites with Y2O3 Sintering Additive

The effect of Y₂O₃ addition (0–5 wt%) on the densification and properties of reactive hot-pressed alumina (Al₂O₃)–boron nitride composites based on the reaction between aluminum borate (2Al₂O₃·B₂O₃) and aluminum nitride (AlN) was investigated. The densification process was very sensitive to the amount of Y₂O₃. Compared with a low relative density of 79.3 theoretical density (TD)% for material with no Y₂O₃ addition, the material density reached 98.6 TD% with 0.25% Y₂O₃ addition. High Y₂O₃ additions resulted in the formation of a new phase Al₅Y₃O₁₂. The grain growth of the Al₂O₃ matrix was promoted by the Y₂O₃ addition. Owing to the high density and the small Al₂O₃ particle size the sample with 0.25% Y₂O₃ addition demonstrated the highest bending strength of 540 MPa.     

High-Temperature Environmental Stability of the Compounds in the Al2O3–Y2O3 System

Heat treatments in several environments were performed on a series of compounds in the Al₂O₃ and Y₂O₃ system: Al₂O₃Y₃Al₅O₁₂ eutectic, Y₃Al₅O₁₂, YAlO₃, Y₄Al₂O₉, and Y₂O₃. The yttrium aluminates were found to be stable at high temperatures under vacuum and in air. However, when they were heat-treated under vacuum in proximity to SiC, degradation was observed. This was found to be primarily a result of carbothermal reduction. In a similarly reducing environment without Si, the yttrium aluminates, and Al₂O₃ and Y₂O₃, all exhibited degradation by carbothermal reduction. Based upon the experimental results, a degradation mechanism for yttrium aluminates was proposed.     

High-Temperature Neutron Diffraction of the AlN–Al2O3–Y2O3 System

The importance of aluminum nitride (AlN) stems from its application in microelectronics as a substrate material due to high thermal conductivity, high electrical resistance, mechanical strength and hardness, thermal durability, and chemical stability. Yttria (Y₂O₃) is the best additive for AlN sintering. AlN densifies by a liquid-phase mechanism, where the surface oxide, Al₂O₃, reacts with Y₂O₃ to form an Y-Al-O-N liquid that promotes particle rearrangement and densification. Construction of the phase relations in this multicomponent system is essential for optimizing the properties of AlN. The ternary phase diagram of the AlN–Al₂O₃–Y₂O₃ was developed by Gibbs energy minimization using interpolation procedures based on modeling the binary subsystems. This paper aims at testing the resultant understanding experimentally at selected compositions using in situ high-temperature neutron diffractometry. These experimental results agree with the thermodynamic calculations of AlN–Al₂O₃–Y₂O₃. The ternary phase diagram has been constructed for the first time in this work. High-temperature neutron diffractometry has permitted real time measurement of the reactions involved in this ternary system, especially to determine the temperature range for each reaction, which would have been difficult to establish by other means.     

Influence of the Y2O3 Content and Temperature on the Mechanical Properties of Melt-Grown Al2O3–ZrO2 Eutectics

The effect of Y₂O₃ content on the flexure strength of melt-grown Al₂O₃–ZrO₂ eutectics was studied in a temperature range of 25°–1427°C. The processing conditions were carefully controlled to obtain a constant microstructure independent of Y₂O₃ content. The rod microstructure was made up of alternating bands of fine and coarse dispersions of irregular ZrO₂ platelets oriented along the growth axis and embedded in the continuous Al₂O₃ matrix. The highest flexure strength at ambient temperature was found in the material with 3 mol% Y₂O₃ in relation to ZrO₂(Y₂O₃). Higher Y₂O₃ content did not substantially modify the mechanical response; however, materials with 0.5 mol% presented a significant degradation in the flexure strength because of the presence of large defects. They were nucleated at the Al₂O₃–ZrO₂ interface during the martensitic transformation of ZrO₂ on cooling and propagated into the Al₂O₃ matrix driven by the tensile residual stresses generated by the transformation. The material with 3 mol% Y₂O₃ retained 80% of the flexure strength at 1427°C, whereas the mechanical properties of the eutectic with 0.5 mol% Y₂O₃ dropped rapidly with temperature as a result of extensive microcracking.     

Physical Properties and Structure of rf-Sputtered Amorphous Films in the System Al2O3–Y2O3

Amorphous films in the system Al₂O₃–Y₂O₃ were prepared by the rf sputtering method in the range of 0–76 mol% Y₂O₃, and their density, refractive index, and elastic constants were measured. All of the physical properties of the amorphous Al₂O₃–Y₂O₃ films had a similar compositional dependence; that is, they increased continuously, but not linearly with increasing Y₂O₃ content. To confirm the coordination states of aluminum and yttrium ions in the amorphous Al₂O₃–Y₂O₃ films, the Al K α X-ray emission spectra and the X-ray absorption near edge structures (XANES) were measured. The average coordination number of aluminum ions in the amorphous films containing up to about 40 mol% Y₂O₃ content was 5, that is a mixture of 4-fold- and 6-fold-coordinated states. In the region of more than about 50 mol% Y₂O₃, the fraction of the 6-fold-coordinated aluminum ions increased with increasing Y₂O₃ content, while the results led to the conclusion that the coordination number of yttrium ions was always 6, regardless of composition. These results indicate that, in amorphous films in the system Al₂O₃–Y₂O₃, the change of the coordination state of aluminum ions has an important effect on physical properties.     

Eutectic Composition in the Pseudobinary of Y4Al2O9 and Y2O3

The eutectic composition between Y₄Al₂O₉ and Y₂O₃ was determined using electron probe microanalysis (EPMA) on directionally solidified specimens with hypo- and hypereutectic compositions. The microstructures of the specimens as a function of composition differ considerably with small deviation from the eutectic composition (70.5 mol% Y₂O₃ and 29.5 mol% Al₂O₃). Based on the current results and other published data, the pseudobinary system between Al₂O₃ and Y₂O₃ is revised.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Strength and Fracture Toughness of Isostatically Hot-Pressed Composites of Al2O3 and Y2O3-Partially-Stabilized ZrO2

Composites of Al₂O₃ and Y₂O₃ partially-stabilized ZrO₂ were isostatically hot-pressed using submicrometer powders as the starting material. The addition of Al₂O₃ resulted in a large increase in bending strength. The average bending strength for a composite containing 20 wt% Al₂O₃ was 2400 MPa, and its fracture toughness was 17 MN·w^−3/2     

Low-Temperature High-Pressure Consolidation of Amorphous Al2O3–15 mol% Y2O3

This study examined pressure consolidation of amorphous Al₂O₃–15 mol% Y₂O₃ powders prepared by co-precipitation and spray pyrolysis. The two amorphous powders had similar true densities and crystallization sequences. Uniaxial hot pressing was carried out at 450°–600°C with a moderate pressure of 750 MPa. The co-precipitated powder could be hot pressed to a maximum relative density of 98% and remained amorphous. Pressure adversely affected the densification of the spray-pyrolyzed powder by favoring an early crystallization of γ-Al₂O₃ phase at 580°C. Plastic deformation of the amorphous phase is believed to be responsible for the large densification of the amorphous powders.     

Refractory α-SiAlON Containing La2O3

Refractory Y-α-SiAlON with elongated grain morphology was obtained by utilizing La₂O₃ as a densification aid, which resulted in excellent room-temperature and high-temperature strength. Room-temperature strength of 1000 MPa was achieved when La₂O₃ was augmented by adding Y₂O₃ or removing AlN. With only La₂O₃, a temperature-independent strength of 800–950 MPa was maintained up to 1100°C, then gradually decreasing by 25% when reaching 1300°C. The R-curve measurements of fracture toughness showed relatively little dependence on microstructure, consistent with a strong interface that suppresses grain boundary decohesion. Compared with other densification aids such as SiO₂, Al₂O₃, Sc₂O₃, Y₂O₃, and Lu₂O₃, a finer microstructure was obtained by using La₂O₃. High nitrogen content in the residual La–Si–Al–O–N glass in equilibrium with the nitrogen-rich α-SiAlON is suggested to be the cause of these findings.     

Sintering Kinetics at Constant Rates of Heating: Effect of Al2O3 on the Initial Sintering Stage of Fine Zirconia Powder

The sinterabilities of fine zirconia powders including 5 mass% Y₂O₃ were investigated, with emphasis on the effect of Al₂O₃ at the initial sintering stage. The shrinkage of powder compact was measured under constant rates of heating (CRH). The powder compact including a small amount of Al₂O₃ increased the densification rate with elevating temperature. The activation energies at the initial stage of sintering were determined by analyzing the densification curves. The activation energy of powder compact including Al₂O₃ was lower than that of a powder compact without Al₂O₃. The diffusion mechanisms at the initial sintering stage were determined using the new analytical equation applied for CRH techniques. This analysis exhibited that Al₂O₃ included in a powder compact changed the diffusion mechanism from grain boundary to volume diffusions (VD). Therefore, it is concluded that the effect of Al₂O₃ enhanced the densification rate because of decrease in the activation energy of VD at the initial sintering stage.     

Sintering of Al2O3–TiC Composite in the Presence of Liquid Phase

The results obtained from the sintering of Al₂O₃–50TiC (in weight percent) composite in the temperature range from 1650° to 1800°C with addition of Y₂O₃ are presented. Densification is accelerated by the formation of liquid at temperatures above 1750°C, and 99% of theoretical density can be achieved by vacuum sintering at 1800°C for 15 min. The liquid presented at the sintering temperature is crystallized to YAG (Y₃Al₅O₁₂) during cooling.     

Fracture Toughness of Al2O3-Particle-Dispersed Y2O3-Partially Stabilized Zirconia

The fracture toughness of 3 mol% Y₂O₃-ZrO₂ (3Y-PSZ) composites containing 10–30 vol% Al₂O₃ with different particle sizes was investigated. It was found that Al₂O₃ dispersion of up to 30 vol% increased the fracture toughness by 17% to 30%, and the toughness increase was more remarkable in the composite dispersed with Al₂O₃ particles of larger sizes. By combining the effects of the dispersion toughening and phase transformation toughening, the toughness change in the present materials was theoretically predicted, which was in good agreement with the experimental data.     

High-Temperature Strength and Fracture Toughness of Y2O3-Partially-Stabilized ZrO2/Al2O3 Composites

The temperature dependence of bending strength, fracture toughness, and Young's modulus of composite materials fabricated in the ZrO₂ (Y₂O₃)-Al₂O₃ system were examined. The addition of A1203 enhanced the high-temperature strength. Isostatically hot-pressed, 60 wt% ZrO₂ (2 mol% Y₂O₃)/40 wt% Al₂O₃ exhibited an extremely high strength, 1000 MPa, at 1000°C.     

Effect of Processing Parameters on the Mechanical and Microstructural Behavior of Ultra-Fine Al2O3– (ZrO2+8%Mol Y2O3) Bioceramic, Densified By High-Frequency Induction Heat Sintering

High-frequency induction heat sintering (HFIHS) is a comparatively new technique that consolidates metals and ceramics very rapidly to full density. In this work, superfast densification behavior and the attendant microstructural features of Al₂O₃–(ZrO₂+8% mol Y₂O₃) composites processed by HFIHS were investigated. The effects of processing parameters such as sintering temperatures, pressures, and heating rate, on the mechanical and microstructural properties were studied. The results indicated that HFIHS was effective in the preparation of fine-grained, nearly fully dense Al₂O₃–8YSZ ceramics from the powder with a smaller particle size by optimizing the overall processing parameters.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Rapid Rate Sintering of Nanocrystalline ZrO2−3 mol% Y2O3

Conventional ramp-and-hold sintering with a wide range of heating rates was conducted on submicrometer and nanocrystalline ZrO₂–3 mol% Y₂O₃ powder compacts. Although rapid heating rates have been reported to produce high density/fine grain size products for many submicrometer and smaller starting powders, the application of this technique to ZrO₂–3 mol% Y₂O₃ produced mixed results. In the case of submicrometer ZrO₂–3 mol% Y₂O₃, neither densification nor grain growth was affected by the heating rate used. In the case of nanocrystalline ZrO₂–3 mol% Y₂O₃, fast heating rates severely retarded densiflcation and had a minimal effect on grain growth. The large adverse effect of fast heating rates on the densification of the nanocrystalline powder was traced to a thermal gradient/differential densification effect. Microstructural evidence suggests that the rate of densification greatly exceeded the rate of heat transfer in this material; consequently, the sample interior was not able to densify before being geometrically constrained by a fully dense shell which formed at the sample exterior. This finding implies that rapid rate sintering will meet severe practical constraints in the manufacture of bulk nanocrystalline ZrO₂–3 mol% Y₂O₃ specimens.     

Effects of Grain Size and Humidity on Fretting Wear in Fine-Grained Alumina, Al2O3/TiC, and Zirconia

Friction and wear of sintered alumina with grain sizes between 0.4 and 3 μm were measured in comparison with Al₂O₃/TiC composites and with tetragonal ZrO₂(3 mol% Y₂O₃). The dependence on the grain boundary toughness and residual microstresses is investigated, and a hierarchical order of influencing parameters is observed. In air, reduced alumina grain sizes improve the micromechanical stability of the grain boundaries and the hardness, and reduced wear is governed by microplastic deformation, with few pullout events. Humidity and water slightly reduce the friction of all of the investigated ceramics. In water, this effect reduces the wear of coarser alumina microstructures. The wear of aluminas and of the Al₂O₃/TiC composite is similar; it is lower than observed in zirconia, where extended surface cracking occurs at grain sizes as small as 0.3 μm.     

Interfaces in Oriented Al2O3-ZrO2 (Y2O3) Eutectics

Oriented samples of Al₂O₃-ZrO₂ (Y₂O₃) eutectics consisting of an alumina matrix with zirconia dispersoids were grown by directional solidification. Preferred growth directions and epitaxial relations were determined from X-ray and electron diffraction analyses. Imaging of interfaces was performed by high-resolution transmission electron microscopy on oriented platelets. Semicoherent interfaces were observed with faceting along crystallographic planes of both phases.