Methane combustion and CO oxidation on LaAl1−xMnxO3 perovskite-type oxide solid solutions

Structural, redox and catalytic deep oxidation properties of LaAl_1−xMn_xO₃ (x=0.0, 0.05, 0.1, 0.2, 0.4, 0.6, 0.8, 1.0) solid solutions prepared by the citrate method and calcined at 1073 K were investigated. XRD analysis showed that all the LaAl_1−xMn_xO₃ samples are single phase perovskite-type solid solutions. Particle sizes and surface areas (SA) are in the 280–1180 Å and 4–33 m² g⁻¹ ranges, respectively. Redox properties and the content of Mn⁴⁺ were derived from temperature programmed reduction (TPR) with H₂. Two reduction steps are observed by TPR for pure LaMnO₃, the first attributed to the reduction of Mn⁴⁺ to Mn³⁺ and the second due to complete reduction of Mn³⁺ to Mn²⁺. The presence of Al in the LaAl_1−xMn_xO₃ solid solutions produces a strong promoting effect on the Mn⁴⁺→Mn³⁺ reducibility and inhibits the further reduction to Mn²⁺. Both for methane combustion and CO oxidation all Mn-containing perovskites are much more active than LaAlO₃, so pointing to the essential role of the transition metal ion in developing highly active catalysts. Partial dilution with Al appears to enhance the specific activity of Mn sites for methane combustion.     

Enhanced high-potential and elevated-temperature cycling stability of LiMn2O4 cathode by TiO2 modification for Li-ion battery

The surface of spinel LiMn₂O₄ was modified with TiO₂ by a simple sol–gel method to improve its electrochemical performance at elevated temperatures and higher working potentials. Compared with pristine LiMn₂O₄, surface-modification improved the cycling stability of the material. The capacity retention of TiO₂-modified LiMn₂O₄ was more than 85% after 60 cycles at high potential cycles between 3.0 and 4.8 V at room temperature and near to 90% after 30 cycles at elevated temperature of 55 °C at 1C charge–discharge rate. SEM studies shows that the surface morphology of TiO₂-modified LiMn₂O₄ was different from that of pristine LiMn₂O₄. Powder X-ray diffraction indicated that spinel was the only detected phase in TiO₂-modified LiMn₂O₄. Introduction of Ti into LiMn₂O₄ changed the electronic structures of the particle surface. Therefore a surface solid compound of LiTi_xMn_2−xO₄ may be formed on LiMn₂O₄. The improved electrochemical performance of surface-modified LiMn₂O₄ was attributed to the improved stability of crystalline structure and the higher Li⁺ conductivity.     

Characterization of Al-doped spinel LiMn2O4 thin film cathode electrodes prepared by Liquid Source Misted Chemical Deposition (LSMCD) technique

A novel process called Liquid Source Misted Chemical Deposition (LSMCD) was used to synthesize Al-doped LiMn₂O₄ cathode films for Lithium microbatteries. The cathode films were characterized by XRD, SEM, cyclic volatmmetry, and charge/discharge test. LiMn_1.8Al_0.2O₄ film crystallized at 800 °C in rapid thermal annealing (RTA) for 5 min under oxygen atmosphere exhibited more improved electrochemical rechargeability than spinel LiMn₂O₄ film because the substitution of Al³⁺ for Mn³⁺ increased Mn---O bonding strength in the spinel framework and suppressed the two-phase behavior of the unsubstituted spinel during the intercalation/deintercalation that is the origin of the failure mechanism in the 4 V region. As a result, LiMn_1.8Al_0.2O₄ film showed an initial discharge capacity of 52 μAh/cm² μm and no capacity fade over 100 cycles.     

TayNb1−yVO5 (0<y<1) mixed oxides synthesized by sol–gel method: electrochemical Li-insertion

Mixed oxides of general formulae Ta_yNb_1−yO₅ (0<y<1) have been synthesized by a modified sol–gel method. Characterization of the samples has been carried out by x-ray diffraction, SEM/EDX, FTIR spectroscopy and thermal analysis. The electrochemical properties have been studied in a lithium cell. The first discharge capacity decrease from 206 (y=0.25) to 136 mA h g⁻¹ (y=0.75). Ta_yNb_1−yO₅ samples undergo an irreversible structural changes induced by electrochemical Li⁺-insertion. For all compositions, the new compounds formed after the first discharge has a very high cyclability, as shown the low capacity loss <1% per cycle.     

Thermoelectric characterization of NaxMx/2Ti1−x/2O2 (M=Co, Ni and Fe) polycrystalline materials

Layered -titanate materials, Na_xM_x/2Ti_1−x/2O₂ (M=Co, Ni and Fe, x=0.2–0.4), were synthesized by flux reactions, and electrical properties of polycrystalline products were measured at 300–800 °C. After sintering at 1250 °C in Ar, all products show n-type thermoelectric behavior. The values of both d.c. conductivity and Seebeck coefficient of polycrystalline Na_0.4Ni_0.2Ti_0.8O₂ were ca. 7×10³ S/m and ca. −193 μV/K around 700 °C, respectively. The measured thermal conductivity of layered -titanate materials has lower value than conductive oxide materials. It was ca. 1.5 Wm⁻¹ K⁻¹ at 800 °C. The estimated thermoelectric figure-of-merit, Z, of Na_0.4Ni_0.2Ti_0.8O₂ and Na_0.4Co_0.2Ti_0.8O₂ was about 1.9×10⁻⁴ and 1.2×10⁻⁴ K⁻¹ around 700 °C, respectively.     

AFeO3 (A=La, Nd, Sm) and LaFe1−xMgxO3 perovskites as methane combustion and CO oxidation catalysts: structural, redox and catalytic properties

Catalytic methane combustion and CO oxidation were investigated over AFeO₃ (A=La, Nd, Sm) and LaFe_1−xMg_xO₃ (x=0.1, 0.2, 0.3, 0.4, 0.5) perovskites prepared by citrate method and calcined at 1073 K. The catalysts were characterized by X-ray diffraction (XRD). Redox properties and the content of Fe⁴⁺ were derived from temperature programmed reduction (TPR). Specific surface areas (SA) of perovskites were in 2.3–9.7 m² g⁻¹ range. XRD analysis showed that LaFeO₃, NdFeO₃, SmFeO₃ and LaFe_1−xMg_xO₃ (x·0.3) are single phase perovskite-type oxides. Traces of La₂O₃, in addition to the perovskite phase, were detected in the LaFe_1−xMg_xO₃ catalysts with x=0.4 and 0.5. TPR gave evidence of the presence in AFeO₃ of a very small fraction of Fe⁴⁺ which reduces to Fe³⁺. The fraction of Fe⁴⁺ in the LaFe_1−xMg_xO₃ samples increased with increasing magnesium content up to x=0.2, then it remained nearly constant. Catalytic activity tests showed that all samples gave methane and CO complete conversion with 100% selectivity to CO₂ below 973 and 773 K, respectively. For the AFeO₃ materials the order of activity towards methane combustion is La>Nd>Sm, whereas the activity, per unit SA, of the LaFe_1−xMg_xO₃ catalysts decreases with the amount of Mg at least for the catalysts showing a single perovskite phase (x=0.3). Concerning the CO oxidation, the order of activity for the AFeO₃ materials is Nd>La>Sm, while the activity (per unit SA) of the LaFe_1−xMg_xO₃ catalysts decreases at high magnesium content.     

Performance of La1−xSrxAl1−y−y′FeyMgy′O3−δ perovskites in methane combustion: effect of aluminum and magnesium content

Perovskites of different La_1−xSr_xAl_1−y−y′Fe_yMg_y′O_3−δ compositions (x=0, 0.1, 0.15, 0.2 and y=0.1, 0.3, 0.5, 0.8) were prepared from a reactive precursor slurry of hydrated oxides. Each sample was aged between 16 and 26 h up to 1473 K. Activity in methane combustion (1%/air) was determined in a plug-flow reactor, with 1 g catalyst and 24 l/h flowrate. Gradual decrease in activity due to thermal aging was observed, the degree of activity loss being composition dependent. Nevertheless, activity of samples aged at 1370 K was nearly independent of composition. The best thermal stability showed LaAl_0.65Fe_0.15Mg_0.2O₃ perovskite. None of the magnesium substituted perovskites performed better than a La_0.85Sr_0.15Al_0.87Fe_0.13O₃ reference sample.     

Nanosized perovskite-type oxides La1−xSrxMO3−δ (M = Co, Mn; x = 0, 0.4) for the catalytic removal of ethylacetate

Nanometer perovskite-type oxides La_1−xSr_xMO_3−δ (M = Co, Mn; x = 0, 0.4) have been prepared using the citric acid complexing-hydrothermal-coupled method and characterized by means of techniques, such as X-ray diffraction (XRD), BET, high-resolution scanning electron microscopy (HRSEM), X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD), and temperature-programmed reduction (TPR). The catalytic performance of these nanoperovskites in the combustion of ethylacetate (EA) has also been evaluated. The XRD results indicate that all the samples possessed single-phase rhombohedral crystal structures. The surface areas of these nanomaterials ranged from 20 to 33 m² g⁻¹, the achievement of such high surface areas are due to the uniform morphology with the typical particle size of 40–80 nm (as can be clearly seen in their HRSEM images) that were derived with the citric acid complexing-hydrothermally coupled strategy. The XPS results demonstrate the presence of Mn⁴⁺ and Mn³⁺ in La_1−xSr_xMnO_3−δ and Co³⁺ and Co²⁺ in La_1−xSr_xCoO_3−δ, Sr substitution induced the rises in Mn⁴⁺ and Co³⁺ concentrations; adsorbed oxygen species (O⁻, O₂⁻, or O₂²⁻) were detected on the catalyst surfaces. The O₂-TPD profiles indicate that Sr doping increased desorption of the adsorbed oxygen and lattice oxygen species at low temperatures. The H₂-TPR results reveal that the nanoperovskite catalysts could be reduced at much lower temperatures (<240 °C) after Sr doping. It is observed that under the conditions of EA concentration = 1000 ppm, EA/oxygen molar ratio = 1/400, and space velocity = 20,000 h⁻¹, the catalytic activity (as reflected by the temperature (T_100%) for EA complete conversion) increased in the order of LaCoO_2.91 (T_100% = 230 °C) ≈ LaMnO_3.12 (T_100% = 235 °C) < La_0.6Sr_0.4MnO_3.02 (T_100% = 190 °C) < La_0.6Sr_0.4CoO_2.78 (T_100% = 175 °C); furthermore, there were no formation of partially oxidized by-products over these catalysts. Based on the above results, we conclude that the excellent catalytic performance is associated with the high surface areas, good redox properties (derived from higher Mn⁴⁺/Mn³⁺ and Co³⁺/Co²⁺ ratios), and rich lattice defects of the nanostructured La_1−xSr_xMO_3−δ materials.     

Synthesis and properties of Bi0.5(Na1−x−yKxAgy)0.5TiO3 lead-free piezoelectric ceramics

Bi_0.5(Na_1−x−yK_xAg_y)_0.5TiO₃ piezoelectric ceramics were prepared by conventional ceramic processes. X-ray diffraction patterns show a pure perovskite structure, indicating that the K⁺ and Ag⁺ ions substitute for the Na⁺ ions in Bi_0.5Na_0.5TiO₃. The temperature dependence of the dielectric constant and dissipation factor shows all ceramics to experience two phase transitions: from ferroelectric to anti-ferroelectric and from anti-ferroelectric to paraelectric. The transition temperature from ferroelectric to anti-ferroelectric and the temperature at which the dielectric constant reaches its maximum value decrease with the increase of K⁺ amount. At room temperature, the ceramics containing 17.5–20 mol% K⁺ and 2 mol% Ag⁺ exhibit high piezoelectric constant (d₃₃ = 180 pC/N) and high electromechanical coupling factor (k_p = 35%).     

Kinetics of the water–gas shift reaction over nanostructured copper–ceria catalysts

Water–gas shift reaction was studied over two nanostructured Cu_xCe_1−xO_2−y catalysts: a Cu_0.1Ce_0.9O_2−y catalyst prepared by a sol–gel method and a Cu_0.2Ce_0.8O_2−y catalyst prepared by co-precipitation method. A commercial low temperature water–gas shift CuO–ZnO–Al₂O₃ catalyst was used as reference. The kinetics was studied in a plug flow micro reactor at an atmospheric pressure in the temperature interval between 298 and 673 K at two different space velocities: 5.000 and 30.000 h⁻¹, respectively. Experimentally estimated activation energy, E_af, of the forward water–gas shift reaction at CO/H₂O = 1/3 was 51 kJ/mol over the Cu_0.1Ce_0.9O_2−y, 34 kJ/mol over the Cu_0.2Ce_0.8O_2−y and 47 kJ/mol over the CuO–ZnO–Al₂O₃ catalyst. A simple rate expression approximating the water–gas shift process as a single reversible surface reaction was used to fit the experimental data in order to evaluate the rate constants of the forward and backward reactions and of the activation energy for the backward reaction.     

Facile synthesis of spinel LiNi0.5Mn1.5O4 as 5.0 V-class high-voltage cathode materials for Li-ion batteries

LiNi_0.5Mn_1.5O₄ and LiMn₂O₄ with novel spinel morphology were synthesized by a hydrothermal and post-calcination process. The synthesized LiMn₂O₄ particles (5-10 μm) are uniform hexahedron, while the LiNi_0.5Mn_1.5O₄ has spindle-like morphology with the long axis 10-15 μm, short axis 5-8 μm. Both LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ show high capacity when used as cathode materials for Li-ion batteries. In the voltage range of 2.5-5.5 V at room temperature, the LiNi_0.5Mn_1.5O₄ has a high discharge capacity of 135.04 mA·h·g^-1 at 20 mA·g^-1, which is close to 147 mA·h·g^-1 (theoretical capacity of LiNi_0.5Mn_1.5O₄). The discharge capacity of LiMn₂O₄ is 131.08 mA·h·g^-1 at 20 mA·g^-1. Moreover, the LiNi_0.5Mn_1.5O₄ shows a higher capacity retention (76%) compared to that of LiMn₂O₄ (61%) after 50 cycles. The morphology and structure of LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ are well kept even after cycling as demonstrated by SEM and XRD on cycled LiMn₂O₄ and LiNi_0.5Mn_1.5O₄ electrodes.     

Effect of the method of obtaining Li2CO3---LiyNi1−yO mixtures on the densification of the resulting LixNi1−xO solid solutions

The weight and plaque diameter change following trermal treatment, and the density and lattice constant of lithium-rich Li_xNi_1−xO solid solutions obtained by heat treatment at 750°C of Li₂CO₃---Li_yNi_1−yO (y < x) mixtures were measured as a function of time. It was found that densification of the solid solutions depends on the method of obtaining the Li₂CO₃---Li_yNi_1−yO mixtures. When a large amount of carbonate is put into the starting mixtures Ni---Li₂CO₃-binder, and the powders are milled together, sintering occurs; in contrast, when the carbonate is added after the formation of Li_yNi_1−yO solid solution, so that the interstices of the plaque are filled with molten carbonate, the resulting mixtures exhibit no densification. For densification to occur, Li₂CO₃ must be in intimate contact with the lithium-doped NiO grains.     

Catalytic behavior of La–Sr–Ce–Fe–O mixed oxidic/perovskitic systems for the NO+CO and NO+CH4+O2 (lean-NOx) reactions

Mixed oxides of the general formula La_0.5Sr_xCe_yFeO_z were prepared by using the nitrate method and characterized by XRD and Mössbauer techniques. The crystal phases detected were perovskites LaFeO₃ and SrFeO_3−x and oxides -Fe₂O₃ and CeO₂ depending on x and y values. The low surface area ceramic materials have been tested for the NO+CO and NO+CH₄+O₂ (“lean-NO_x”) reactions in the temperature range 250–550°C. A noticeable enhancement in NO conversion was achieved by the substitution of La³⁺ cation at A-site with divalent Sr⁺² and tetravalent Ce⁺⁴ cations. Comparison of the activity of the present and other perovskite-type materials has pointed out that the ability of the La_0.5Sr_xCe_yFeO_z materials to reduce NO by CO or by CH₄ under “lean-NO_x” conditions is very satisfying. In particular, for the NO+CO reaction estimation of turnover frequencies (TOFs, s⁻¹) at 300°C (based on NO chemisorption) revealed values comparable to Rh/-Al₂O₃ catalyst. This is an important result considering the current tendency for replacing the very active but expensive Rh and Pt metals. It was found that there is a direct correlation between the percentage of crystal phases containing iron in La_0.5Sr_xCe_yFeO_z solids and their catalytic activity. O₂ TPD (temperature-programmed desorption) and NO TPD studies confirmed that the catalytic activity for both tested reactions is related to the defect positions in the lattice of the catalysts (e.g., oxygen vacancies, cationic defects). Additionally, a remarkable oscillatory behavior during O₂ TPD studies was observed for the La_0.5Sr_0.2Ce_0.3FeO_z and La_0.5Sr_0.5FeO_z solids.     

Application of Ce0.33Zr0.63Pr0.04O2-supported noble metal catalysts in the catalytic wet air oxidation of 2-chlorophenol: Influence of the reaction conditions

In this work, different procedures, namely carbonate coprecipitation and modified solid–solid diffusion, were used to prepare hexaaluminate samples, unsupported or supported onto θ-Al₂O₃. These samples were used as catalyst for the methane total oxidation as synthesized or after impregnation of 1 wt% Pd. It was observed that the modified solid–solid diffusion procedure is an efficient method to obtain the hexaaluminate structure. At a theoretical ratio x of hexaaluminate onto Al₂O₃ less than 0.6 (xLa_0.2Sr_0.3Ba_0.5MnAl₁₁O₁₉ + (1−x)·Al₂O₃, with x = 0.25, 0.60), samples with high specific surface area and θ-Al₂O₃ structure are then obtained. Large differences in catalytic activity can be observed among the series of sample synthesized. All the pure oxide samples (i.e. without palladium) present low catalytic activity for methane total oxidation compared to a reference Pd/Al₂O₃ catalyst. The highest activity was obtained for the samples presenting a θ-Al₂O₃ structure (with x = 0.60) and a high surface area. Impregnation of 1 wt% palladium resulted in an increase in catalytic activity, for all the solids synthesized in this work. Even if the lowest light-off temperature was obtained on the reference sample, similar methane conversions at high temperature (700 °C) were obtained on the stabilized θ-Al₂O₃ solids (x = 0.25, 0.60). Moreover, the reference sample is found to strongly deactivate with reaction time at the temperature of test (700 °C), due to a progressive reduction of the PdO_x active phase into the less active Pd° phase, whereas excellent stabilities in reaction were obtained on the pure and palladium-doped hexaaluminate and supported θ-Al₂O₃ samples. This clearly showed the beneficial effect of the support for the stabilization of the PdO_x active phase at high reaction temperature. These properties are discussed in term of oxygen transfer from the support to the palladium particle. Oxygen transfer is directly related to the Mn³⁺/Mn²⁺ redox properties (in the case of the hexaaluminate and stabilized θ-Al₂O₃ samples), that allows a fast reoxidation of the metal palladium sites since palladium sites reoxidation cannot occur directly by gaseous dioxygen adsorption and dissociation on the surface.     

Synthesis, characterization and catalytic activity for NO–CO reaction of Pd–(La, Sr)2MnO4 system

La_xSr_2−xMnO₄ (0 ≤ x ≤ 0.8) oxides were synthesized and single-phase K₂NiF₄-type oxides were obtained in the range of 0.1 ≤ x < 0.5. The catalytic activity of La_xSr_2−xMnO₄ for NO–CO reaction increased with increasing x in the range of solubility limit of La. La_0.5Sr_1.5MnO₄ showed the highest activity among La_xSr_2−xMnO₄ prepared in this study, but its activity was inferior to perovskite-type La_0.5Sr_0.5MnO₃. Among the Pd-loaded catalysts, however, Pd/La_0.8Sr_1.2MnO₄ showed the higher activity and the selectivity to N₂ than Pd/La_0.5Sr_0.5MnO₃ and Pd/γ-Al₂O₃. The excellent catalytic performance of Pd/La_0.2Sr_1.2MnO₄ could be ascribable to the formation of SrPd₃O₄ which was detected by XRD in the catalyst but not in the other two catalysts.     

The homogeneity range and the microwave dielectric properties of the BaZn2Ti4O11 ceramics

Ceramics with a composition close to BaZn₂Ti₄O₁₁ were synthesized according to various substitutional mechanisms in order to verify an existence of a homogeneity range in the vicinity of this composition. Structural and microstructural investigations showed that the crystal structure of BaZn₂Ti₄O₁₁ was formed in the homogeneity range corresponding to the formula BaZn_2 − xTi₄O_11 − x (0 < x < 0.1). Densely sintered BaZn_2 − xTi₄O_11 − x (0 < x < 0.1) ceramics exhibited a dielectric constant around 30, τ_f = −30 ppm/K and high Q × f values, which increased from 68,000 GHz at x = 0 to 83,000 GHz at x = 0.05. Structurally, the deficiency of Zn in BaZn_2 − xTi₄O_11 − x (0 < x < 0.1) resulted in a slight decrease in the unit-cell volume. The influence of secondary phases in the BaZn₂Ti₄O₁₁-based materials on the microwave dielectric properties was also investigated. A presence of small amounts of ZnO, BaTiO₃, hollandite-type solid solutions (Ba_xZn_xTi_8 − xO₁₆) and BaTi₄O₉ caused a decrease in Q × f values.     

Decomposition of nitric oxide over perovskite oxide catalysts: effect of CO2, H2O and CH4

Direct nitric oxide decomposition over perovskites is fairly slow and complex, its mechanism changing dramatically with temperature. Previous kinetic study for three representative compositions (La_0.87Sr_0.13Mn_0.2Ni_0.8O_3−δ, La_0.66Sr_0.34Ni_0.3Co_0.7O_3−δ and La_0.8Sr_0.2Cu_0.15Fe_0.85O_3−δ) has shown that depending on the temperature range, the inhibition effect of oxygen either increases or decreases with temperature. This paper deals with the effect of CO₂, H₂O and CH₄ on the nitric oxide decomposition over the same perovskites studied at a steady-state in a plug-flow reactor with 1 g catalyst and total flowrates of 50 or 100 ml/min of 2 or 5% NO. The effect of carbon dioxide (0.5–10%) was evaluated between 873 and 923 K, whereas that of H₂O vapor (1.6 or 2.5%) from 723 to 923 K. Both CO₂ and H₂O inhibit the NO decomposition, but inhibition by CO₂ is considerably stronger. For all three catalysts, these effects increase with temperature. Kinetic parameters for the inhibiting effects of CO₂ and H₂O over the three perovskites were determined. Addition of methane to the feed (NO/CH₄=4) increases conversion of NO to N₂ about two to four times, depending on the initial NO concentration and on temperature. This, however, is still much too low for practical applications. Furthermore, the rates of methane oxidation by nitric oxide over perovskites are substantially slower than those of methane oxidation by oxygen. Thus, perovskites do not seem to be suitable for catalytic selective NO reduction with methane.     

Effective Au-Au-Clx/Fe(OH)y catalysts containing Cl for selective CO oxidations at lower temperatures

Supported Au catalysts Au-Au⁺-Cl_x/Fe(OH)_y (x < 4, y ≤ 3) and Au-Cl_x/Fe₂O₃ prepared with co-precipitation without any washing to remove Cl⁻ and without calcining or calcined at 400 °C were studied. It was found that the presence of Cl⁻ had little impact on the activity over the unwashed and uncalcined catalysts; however, the activity for CO oxidation would be greatly reduced only after Au-Au⁺-Cl_x/Fe(OH)_y was further calcined at elevated temperatures, such as 400 °C. XPS investigation showed that Au in catalyst without calcining was composed of Au and Au⁺, while after calcined at 400 °C it reduced to Au⁰ completely. It also showed that catalysts precipitated at 70 °C could form more Au⁺ species than that precipitated at room temperatures. Results of XRD and TEM characterizations indicated that without calcining not only the Au nano-particles but also the supports were highly dispersed, while calcined at 400 °C, the Au nano-particles aggregated and the supports changed to lump sinter. Results of UV–vis observation showed that the Fe(NO₃)₃ and HAuCl₄ hydrolyzed partially to form Fe(OH)₃ and [AuCl_x(OH)_4−x]⁻ (x = 1–3), respectively, at 70 °C, and such pre-partially hydrolyzed iron and gold species and the possible interaction between them during the hydrolysis may be favorable for the formation of more active precursor and to avoid the formation of Au–Cl bonds. Results of computer simulation showed that the reaction molecular of CO or O₂ were more easily adsorbed on Au⁺ and Au⁰, but was very difficultly absorbed on Au⁻. It also indicated that when Cl⁻ was adsorbed on Au⁰, the Au atom would mostly take a negative electric charge, which would restrain the adsorption of the reaction molecular severely and restrain the subsequent reactions while when Cl⁻ was adsorbed on Au⁺ there only a little of the Au atom take negative electric charge, which resulting a little impact on the activity.     

Ce1−xCuxO2−x/Al2O3/FeCrAl catalysts for catalytic combustion of methane

A series of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts (x = 0–1) were prepared. The structure of the catalysts was characterized using XRD, SEM and H₂-TPR. The catalytic activity of the catalysts for the combustion of methane was evaluated. The results indicated that in the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts the surface phase structure were the Ce_1−xCu_xO_2−x solid solution, -Al₂O₃ and γ-Al₂O₃. The surface particle shape and size were different with the variety of the molar ratio of Ce to Cu in the Ce_1−xCu_xO_2−x solid solution. The Cu component of the Ce_1−xCu_xO_2−x/Al₂O₃/FeCrAl catalysts played an important role to the catalytic activity for the methane combustion. There were the stronger interaction among the Ce_1−xCu_xO_2−x solid solution and the Al₂O₃ washcoats and the FeCrAl support.     

Crystalline structure and electrical properties of YCuxMn1–xO3 solid solutions

Solid solutions belonging to the Mn-rich region of the YCu_xMn_1–xO₃ system have been studied. The powders were prepared by solid-state reaction between the corresponding oxides. Sintered ceramics were obtained by firing at 1100–1325 °C. The incorporation of 30 at.% Cu to the yttrium manganite induces the formation of a perovskite-type phase, with orthorhombic symmetry. Increase of the Cu amount do not appreciably affects the orthorhombicity factor b/a, up to an amount of 50 at.% Cu. Above this Cu amount, a multiphase system has been observed, with the presence of unreacted-Y₂O₃, YMnO₃ and Y₂Cu₂O₅, along with a perovskite phase. DC electrical conductivity measurements have shown a semiconducting behaviour for all the solid solutions with perovskite-type structure. The room temperature conductivity increases with Cu until 33 at.% Cu, and then decreases. Thermally activated small polaron hopping mechanism, between Mn³⁺ and Mn⁴⁺ cations, controls the conductivity in these ceramics. Results are discussed as a function of the Mn³⁺/Mn⁴⁺ ratio for each composition.