Dropwise condensation on L-B film surface

A method of achieving dropwise condensation using Langmuir-Blodgett (L-B) built-up film technology is presented. One and three layers of barium stearate monomolecular film were prepared on the copper plates, and excellent dropwise condensation of steam was formed on the surfaces, respectively. The heat transfer coefficients of dropwise condensation on these treated surfaces are more than 30 times higher than that of filmwise condensation on a bare surface.     

表面分割方式对滴膜共存冷凝传热特性的实验研究

实验研究了滴膜面积比为1：1且滴状区域采用较厚的有机涂层时，垂直管外滴膜共存表面的滴膜区域分割方式对冷凝传热特性的影响。结果表明，在表面分割方式一定时，滴膜共存表面的冷凝传热性能随着表面分割数的增加而增加，但总仍是介于全部表面为滴状冷凝和全表面为膜状冷凝型态之间的传热特性。分析表面分割数分别为2和4的滴膜共存表面的传热结果，发现凝液环的缓冲作用对于滴膜共存表面的冷凝强化传热具有重要作用。滴膜共存表面上滴状冷凝区面积对其下游膜状冷凝传热的影响不仅与滴膜区域的面积比有关，而且实验操作条件也有一定的控制作用，且两者之间存在最佳匹配值，即此时的强化传热效果最好。     

滴膜共存表面强化冷凝传热

<正>滴状冷凝具有很高的传热速率,其冷凝传热系数是膜状冷凝的几倍至几十倍,但是,由于长期维持滴状冷凝表面制备技术的限制,该技术距工业化应用还有一定的距离,在滴状冷凝的研究过程中,经常发现滴膜共存冷凝现象,而且传热系数较普通的膜状冷凝有较大的提高,在以往的实验研究中,往往不能肯定地排除蒸汽中有机杂质的影响,滴膜共存表面的实验研究也间接地证实了蒸汽中是不含有机杂质的,滴膜共存表面也是强化冷凝传热很实用的技术,是滴状冷凝传热过程全面工业化的过渡阶段.所以,研究滴膜共存表面强化冷凝传热的特性具有重要的理论意义和实用价值.Kumagai等报道了在竖平面上垂直分割的滴膜共存表面上冷凝传热的实验.结果表明,当滴状冷凝区和膜状冷凝区的面积比为1:1时,平均热负荷要高于在通常表面上滴状冷凝和膜状冷凝热负荷的算术平均值,而且平均热负荷与表面分割方式和分割数目有关.他们在一种特殊分割形式的表面上得到的最大热负荷高于当全部表面为滴状冷凝时的最大热负荷.     

R404A在水平内螺纹管中的冷凝传热研究

经过实验与理论对比,研究了R404A在外径9.52 mm内螺纹管内局部平均冷凝换热系数。采用Cavallini纯工质与混合工质关联式分别计算的冷凝换热系数,最大偏差不到4%。在工程计算R404A内螺纹管内冷凝换热系数时,可将其以纯质来对待。分析比较Cavallini,Yu-Koyama和Kaushink-Azer关联式,各自的理论预测值和实验结果相比,表明Cavallini关联式的预测精度最高,其标准偏差为7.76%。因此Cavallini关联式对于R404A在管内的冷凝换热预测有较好的适用性。研究结果对R404A冷凝器的工程设计及其优化具有一定的参考意义。     

组合表面调控液滴特性强化蒸汽冷凝传热

制备了具有不同疏水区宽度和面积分率的疏水-亲水间隔规则排列的组合表面。观测常压蒸汽在组合表面上冷凝时疏水区液滴的特性(液滴移除方式和最大液滴半径),利用格子Boltzmann方法模拟组合表面上凝液的运动。考察疏水区、亲水区宽度和表面过冷度对组合表面强化蒸汽冷凝传热的影响。利用滴状-膜状组合传热模型分析组合表面蒸汽冷凝传热性能的影响因素,并与实验结果比较。发现疏水区液滴自发地向亲水区定向迁移,精细设计的组合表面可以实现蒸汽滴状冷凝传热的强化,实验中强化因子可达1.20。疏水区宽度约为0.55 mm时组合表面的传热性能最大。表面过冷度越大,组合表面强化传热的效果越差,模型分析与实验结果吻合良好。     

聚合物表面性能对强化冷凝传热的影响

对离子束动态混合注入(DIMI)技术制备的黄铜、紫铜、不锈钢和碳钢管基聚四氟乙烯(PTFE)表面的冷凝传热实验发现,用不同加工条件制备的表面具有不同的化学组成、不均匀的表面状态以及不同的物理化学性质,从而导致不同的冷凝成滴面积和传热性能,而且表面加工条件对滴状冷凝传热的寿命有至关重要的作用,不同基体材料应有不同的最佳制备工艺条件.不同工艺条件下制备黄铜基PTFE表面水蒸气竖直管外冷凝传热通量比相应的膜状冷凝提高0.3-4.6倍,冷凝传热系数提高1.6-28.6倍.实验结果也表明冷凝表面基体材料对冷凝传热性能有一定的影响.     

Transfer coefficients for the liquid–vapor interface of a two-component mixture

We present the excess entropy production for heat and mass transport across an interface of a non-ideal two-component mixture, using as interface variables the excess densities proposed by Gibbs. With the help of these variables we define the interface as an autonomous system in local equilibrium and study its transport properties. The entropy production determines the conjugate fluxes and forces, and equivalent forms are given. The forms contain finite differences of intensive variables into and across the surface as driving forces. These expressions for the fluxes serve as boundary conditions for integration across heterogeneous systems that are far from global equilibrium.The resistivities to heat transfer and the coupling coefficients for heat and mass transfer were determined using non-equilibrium molecular dynamics (NEMD) simulations in a system of Lennard-Jones spline particles of the same diameter and mass, but with potential depths that differ by a factor 0.8. The coupling coefficients for heat and mass transfer are significant. A relation of the coupling coefficients and the partial molar enthalpy of evaporation is verified for each component. As a consequence, it is not sufficient to use for instance Fourier's law for transport of heat across surfaces.Support is presented for a new method to find coefficients from integral relations. The method was verified using one of the NEMD coefficients, and used to calculate contributions to the remaining resistivities. One would expect kinetic theory to predict the resistivities at low vapor densities, but this is found to be correct only for the thermal resistivity. The interfacial heat and mass transfer coefficients are found to differ widely from kinetic theory predictions. Estimates of the resistivities to mass transfer differ by more than an order of magnitude. These results will have a bearing on the dynamic modeling of evaporation/condensation and desorption/adsorption.     

Filmwise Condensation Heat Transfer Enhancement with Dropwise and Filmwise Coexisting Condensation Surfaces

Six surfaces were prepared with defferent surface division patterns for the experimental investigationof steam condensation heat transfer characteristics for dropwise and filmwise coexisting(DFC)condensationsurfaces under atmospheric pressure Dropwise condensation(DWC)was promoted with an ultrathin polytetrafluoroethylene(PTFE)film,which was prepared by the dynamic ion-beam mixed implantation(DIMI)method.The results showed that the condensation phenomena at the intersection between the dropwise andfilmwise condensation regios were quite different for different relative positions of the dropwise and filmwisecondensation regions.The experimental results revealed that the condensation heat transfer characteristics werehighly influenced by the surface division number and the relative area ratio of the dropwise and filmwise conden-sation regions.The impact of thesc findings on heat transfer enhancement mechanism for condensation heattransfer is discussed in detail.     

超疏水表面蒸汽及含不凝气蒸汽滴状冷凝传热实验分析

通过紫铜基表面上制备两种具有微纳米结构的超疏水表面以及相同化学修饰的光滑疏水表面,实验研究了各表面上空气环境下水的润湿特性以及在纯蒸汽、蒸汽-空气混合气体环境下,表面的滴状冷凝传热特性和冷凝液滴的运动和润湿特性。结果表明:纯蒸汽滴状冷凝条件下,超疏水表面的传热性能明显低于光滑疏水表面的传热性能;含低浓度不凝气蒸汽冷凝环境下,超疏水表面传热性能与光滑疏水表面相近;蒸汽冷凝环境中,超疏水表面上液滴的接触角明显低于其在空气条件下接触角,并且接触角滞后增大。分析得到,微纳米结构的存在使冷凝过程液滴的接触角滞后增大,微纳米结构中冷凝液滞留增加的壁面热阻等抑制了滴状冷凝传热性能;并提出了蒸汽及含不凝气蒸汽冷凝环境中液滴在超疏水表面上的润湿模式。     

聚四氟乙烯薄膜表面滴状冷凝传热实验研究

为了探索实现滴状冷凝传热的新表面涂层 ,采用离子束动态混合注入技术制备了紫铜基聚四氟乙烯(PTFE)薄膜 ,显著地提高了水蒸气冷凝传热性能。实验表明 ,该表面涂层能够实现常压水蒸气稳定的滴状冷凝形态 ,在表面过冷度 9.8— 1 4 .2K范围内 ,滴状冷凝传热通量和传热系数比膜状冷凝结果提高 30—47倍。同时发现 ,在大气压附近 ,热通量和冷凝传热系数都随着水蒸气蒸汽温度的增加而增加 ,但表面过冷度随蒸气温度增加呈弱增加趋势     

蒸汽冷凝型态的表面自由能差判据

提出了蒸汽在固体表面上冷凝方式的表面自由能差判据 ,即冷凝温度下液体表面自由能与固体表面的表面自由能差大于 33.3mJ·m^-2 时蒸汽在该表面上呈现滴状冷凝的必要条件 .当表面自由能差在 0与 33.3mJ·m^-2范围内 ,表面强化冷凝传热的效果将取决于表面自由能差值的大小 ,差值越大 ,强化效果越明显 .这对深化表面涂层强化冷凝传热的机理以及选择传热表面涂层材料具有指导意义 .通过与文献报道实验结果的比较证实 ,该判据排除了静态接触角判据中测量温度的影响 .     

梯度表面能材料表面上滴状凝结换热

采用气相沉积（CVD）的方法,以十二烷基三氯硅烷和辛基三氯硅烷为扩散工质,制备了梯度表面能材料表面。对空气中水滴在水平梯度表面能材料表面上的运动现象和表面倾角为0°、30°、60°和90°情况下,梯度表面能材料表面上的水蒸气滴状凝结换热进行了可视化实验,研究了凝结液滴的长大、聚并、运动和脱落现象。结果表明：直径大于1 mm的凝结液滴峰值运动速度达到110 mm·s-1,远大于空气中液滴的运动速度。通过图像分析,分别讨论了壁面过冷度、凝结表面倾角和表面能梯度对换热和液滴运动的影响。结果表明：随着壁面过冷度的增加,凝结表面传热系数先增加后减小;当凝结表面倾角大时,由于重力作用加大,凝结表面传热系数也高;当表面能梯度较大时,运动液滴尺寸更小,速度更快,凝结表面传热系数更高。     

在复合镀层表面上实现滴状冷凝传热的研究

研究了采用Ｎｉ－ＰＴＦＥ复合镀层表面实现水蒸气滴状冷凝的新方法。在对Ｎｉ－ＰＴＦＥ复合电镀工艺研究的基础上，进行了水蒸气在无镀层的黄铜板表面和有复合镀层表面的冷凝传热的对比实验。实验结果表明，在Ｎｉ－ＰＴＦＥ复合镀层表面上可实现水蒸气的滴状冷凝，有着显著的强化冷凝换热效果。     

PVDF中空纤维换热管亲/疏水组合表面强化蒸汽冷凝传热

针对塑料换热管热导率低的问题,采用非溶剂致相分离法（NIPS）,通过控制铸膜液中磺化聚醚砜（SPES）添加量,制备出具有致密层/非致密层复合结构,外表面接触角分别为49.8°、78.1°的中空纤维表面亲水（PVDF/SPES）、表面疏水（PVDF）换热管,在非致密层内填充水,从而提高换热管导热性能。将单根的表面亲水、疏水换热管编织,在列管式塑料换热器壳程,利用两根换热管的外表面,构建蒸汽冷凝用亲/疏水组合表面,研究该表面上蒸汽冷凝传热强化效果。研究表明,较熔融拉伸法制备的致密PVDF换热管疏水表面,NIPS法制备的亲水表面、疏水表面及亲/疏水组合表面上的蒸汽冷凝总传热系数分别提高46.6%、56.5%、99.7%。可见,较单一的亲水或疏水表面而言,亲/疏水组合表面能够显著强化蒸汽冷凝传热性能。     

微纳结构超疏水表面参数影响含不凝气蒸汽冷凝传热的理论分析

超疏水表面结构参数对滴状冷凝传热性能、液滴生长和分布均会产生影响。首先利用竖直壁面液滴的受力平衡确定了不凝气条件下蒸汽冷凝过程中液滴的脱落半径,随后建立了含不凝气蒸汽滴状冷凝的传热模型,研究了不同不凝气浓度和过冷度下超疏水表面微柱的柱间距对滴状冷凝传热性能的影响,得到了使超疏水表面冷凝传热性能达到最佳的柱间距值,并对其随不凝气浓度和过冷度的变化规律进行了分析。结果表明在所研究的过冷度范围内,当不凝气浓度较低时（<20%）,最佳柱间距随不凝气浓度升高而增大;而当不凝气浓度高于20%时,最佳柱间距随不凝气浓度升高而减小。为驱动含不凝气蒸汽冷凝传热性能的超疏水微纳结构参数的优化提供了必要的基础数据。     

不同蒸气压力下Marangoni凝结换热特性

在蒸气流速4 m·s^-1的条件下,通过实验研究了不同蒸气压力下纯水、纯酒精和不同酒精浓度水-酒精混合蒸气沿重力方向流过竖直铜平板表面上的凝结换热特性,并实现了实验的可视化,同时从理论上初步分析了混合蒸气压力对Marangoni凝结换热特性的影响.实验及理论分析结果表明,在相同蒸气浓度、蒸气流速和表面过冷度条件下,高压下的凝结换热强度比低压的大.且蒸气压力对凝结换热的影响因混合蒸气酒精浓度的不同而不同,在低浓度1%、2.28%和高浓度22%、51%时压力的增加对凝结换热特性的影响较小,而在中间浓度5.1%和9.8%时凝结换热系数随压力的增加明显.     

Experimental studies on heat transfer with phase change on diverging-converging surfaces

Attempts have been made to study experimentally condensation of pure vapours on the inside surfaces of vertical diverging-converging tubes. The work highlights the significant augmentation in heat transfer efficiency achievable in film condensation on surfaces that are of diverging-converging geometry. The dependence of the augmentation phenomena on the geometric characteristics of the heat transfer surface, such as angle of constriction and number of segments in series, and also on the operating parameters such as fluid flow rate and fluid inlet temperature, is also discussed.     

限制热阻对珠状凝结换热的影响

应用作者提出的数值模拟模型 ,对不同材料表面珠状凝结换热进行了数值模拟 .计算结果表明 :珠状凝结换热系数随冷凝壁材料导热系数的降低而降低     

微尺度通道内R134a的冷凝传热实验研究

建立采用射流冲击进行制冷剂冷却的冷凝传热实验系统,对当量直径为0.63 mm矩形微尺度通道内制冷剂R134a的冷凝传热特性进行研究。实验参数范围是制冷剂干度0~1,质量流率115~290 kg/(m²·s）,饱和压力0.35~0.5 MPa,实验获得了不同工况下微尺度通道的局部冷凝传热系数,并分析了制冷剂各参数对冷凝传热的影响。实验结果表明：冷凝过程中沿制冷剂流动方向,局部冷凝传热系数会随着干度减小而减小;在一定饱和压力下,局部冷凝传热系数与局部热通量相对应;冷凝传热系数随着饱和压力减小而增大。基于实验数据,整理出适用于本实验工况下微尺度通道内R134a的冷凝传热计算公式。     

An experimental study of the effects of surface characteristics and material thermal properties on dropwise condensation

In this investigation, a study of the dropwise mode of condensation of water vapour at near atmospheric pressure was undertaken. Three vertically oriented condenser surfaces of different materials, copper, brass and stainless steel, were carefully prepared and heat transfer data were obtained over a long period of time as the surfaces continued to deteriorate. The condensation heat transfer coefficient was found to decrease with increasing surface deterioration. It is also evident that further work is needed before a general model can be developed to predict heat transfer in dropwise condensation. However the effect of surface characteristics and material thermal properties on strong dropwise condensation at small vapour to surface temperature differences is evident from the present results.