A new ZVT-PWM DC-DC converter

In this paper, a new active snubber cell that overcomes most of the drawbacks of the normal "zero voltage transition-pulse width modulation" (ZVT-PWM) converter is proposed to contrive a new family of ZVT-PWM converters. A converter with the proposed snubber cell can also operate at light load conditions. All of the semiconductor devices in this converter are turned on and off under exact or near zero voltage switching (ZVS) and/or zero current switching (ZCS). No additional voltage and current stresses on the main switch and main diode occur. Also, the auxiliary switch and auxiliary diodes are subjected to voltage and current values at allowable levels. Moreover, the converter has a simple structure, low cost, and ease of control. A ZVT-PWM boost converter equipped with the proposed snubber cell is analyzed in detail. The predicted operation principles and theoretical analysis of the presented converter are verified with a prototype of a 2 kW and 50 kHz PWM boost converter with insulated gate bipolar transistor (IGBT). In this study, a design procedure of the proposed active snubber cell is also presented. Additionally, at full output power in the proposed soft switching converter, the main switch loss is about 27% and the total circuit loss is about 36% of that in its counterpart hard switching converter, and so the overall efficiency, which is about 91% in the hard switching case, increases to about 97%     

A novel lossless passive snubber for soft-switching boost-typeconverters

A novel lossless passive snubber is proposed for soft switching boost-type converters. The proposed snubber does not use any auxiliary switches, but uses two identical snubber capacitors which are charged in parallel at turn off of the main switch and discharged in series at turn on automatically, and the discharged energy is recovered effectively (more than 95% recovery) into the output capacitor. Thus, the snubber provides zero-voltage switching for the converter main switch, reducing both the turn-off losses and the electromagnetic interference (EMI) noise, which improves the converter performance. The experimental results of a 20 kHz 600 W DC-DC boost converter and a single-phase AC-DC boost rectifier with the new snubber are presented     

A zero-voltage-switched PWM boost converter with an energyfeedforward auxiliary circuit

A zero-voltage-switched (ZVS) pulsewidth-modulated (PWM) boost converter with an energy feedforward auxiliary circuit is proposed in this paper. The auxiliary circuit, which is a resonant circuit consisting of a switch and passive components, ensures that the converter's main switch and boost diode operate with soft switching. This converter can function with PWM control because the auxiliary resonant circuit operates for a small fraction of the switching cycle. Since the auxiliary circuit is a resonant circuit, the auxiliary switch itself has both a soft turn on and turn off, resulting in reduced switching losses and electromagnetic interference (EMI). This is unlike other proposed ZVS boost converters with auxiliary circuits where the auxiliary switch has a hard turn off. Peak switch stresses are only slightly higher than those found in a conventional PWM boost converter because part of the energy that would otherwise circulate in the auxiliary circuit and drastically increase peak switch stresses is fed to the load. In this paper, the operation of the converter is explained and analyzed, design guidelines are given, and experimental results obtained from a prototype are presented. The proposed converter is found to be about 2%-3% more efficient than the conventional PWM boost converter     

A new ZVT-ZCT-PWM DC-DC converter

In this paper, a new active snubber cell is proposed to contrive a new family of pulse width modulated (PWM) converters. This snubber cell provides zero voltage transition (ZVT) turn on and zero current transition (ZCT) turn off together for the main switch of a converter. Also, the snubber cell is implemented by using only one quasi resonant circuit without an important increase in the cost and complexity of the converter. New ZVT-ZCT-PWM converter equipped with the proposed snubber cell provides most the desirable features of both ZVT and ZCT converters presented previously, and overcomes most the drawbacks of these converters. Subsequently, the new converter can operate with soft switching successfully at very wide line and load ranges and at considerably high frequencies. Moreover, all semiconductor devices operate under soft switching, the main devices do not have any additional voltage and current stresses, and the stresses on the auxiliary devices are at low levels. Also, the new converter has a simple structure, low cost and ease of control. In this study, a detailed steady state analysis of the new converter is presented, and this theoretical analysis is verified exactly by a prototype of a 1-kW and 100-kHz boost converter.     

Novel zero-Voltage-transition PWM DC-DC converters

A new family of zero-voltage-switching (ZVS) pulsewidth-modulated (PWM) converters that uses a new ZVS-PWM switch cell is presented in this paper. Except for the auxiliary switch, all active and passive semiconductor devices in the ZVS-PWM converters operate at ZVS turn ON and turn OFF. The auxiliary switch operates at zero-current-switching (ZCS) turns ON and OFF. Besides operating at constant frequency, these new converters have no overvoltage across the switches and no additional current stress on the main switch in comparison to the hard-switching converter counterpart. Auxiliary components rated at very small current are used. The principle of operation, theoretical analysis, and experimental results of the new ZVS-PWM boost converter, rated 1 kW, and operating at 80 kHz, are provided in this paper to verify the performance of this new family of converters.     

A true ZCZVT commutation cell for PWM converters

This paper introduces a true zero-current and zero-voltage transition (ZCZVT) commutation cell for DC-DC pulsewidth modulation (PWM) converters operating with an input voltage less than half the output voltage. It provides zero-current switching (ZCS) and zero-voltage switching (ZVS) simultaneously, at both turn on and turn off of the main switch and ZVS for the main diode. The proposed soft-switching technique is suitable for both minority and majority carrier semiconductor devices and can be implemented in several DC-DC PWM converters. The ZCZVT commutation cell is placed out of the power path, and, therefore, there are no voltage stresses on power semiconductor devices. The commutation cell consists of a few auxiliary devices, rated at low power, and it is only activated during the main switch commutations. The ZCZVT commutation cell, applied to a boost converter, has been analyzed theoretically and verified experimentally. A 1 kW boost converter operating at 40 kHz with an efficiency of 97.9% demonstrates the feasibility of the proposed commutation cell     

Soft switching active snubbers for DC/DC converters

A soft-switching active snubber is proposed to reduce the turn-off losses of the insulated gate bipolar transistor (IGBT) in a buck power converter. The soft-switching snubber provides zero-voltage switching for the IGBT, thereby reducing its high turn-off losses due to the current tailing. The proposed snubber uses an auxiliary switch to discharge the snubber capacitor. This auxiliary switch also operates at zero-voltage and zero-current switching. The size of the auxiliary switch compared to the main switch makes this snubber a good alternative to the conventional snubber or even to passive low-loss snubbers. The use of the soft-switching active snubber permits the IGBT to operate at high frequencies with an improved RBSOA. In the experimental results reported for a 1 kW, 40 kHz prototype, combined switching/snubbing losses are reduced by 36% through the use of the active snubber compared to a conventional RCD snubber. The use of an active snubber allows recovery of part of the energy stored in the snubber capacitor during turn-off. The generic snubber cell for the buck power converter is generalized to support the common nonisolated DC/DC power converters (buck, boost, buck-boost, Cuk, sepic, zeta) as well as isolated DC/DC power converters (forward, flyback, Cuk, and sepic)     

A Comparative Study of Zero-Current-Transition PWM Converters

Zero-current-transition pulsewidth-modulation (ZCT-PWM) boost converters are conventional boost converters that use an active auxiliary circuit to turn off the main power switch with zero-current switching; the operation and properties of these converters are the focus of this paper. In this paper, the general operating principles behind all ZCT-PWM converters are reviewed, and the operation and properties of specific converters are discussed. The strengths and weaknesses of each converter are stated, and a new and improved ZCT-PWM boost converter is proposed and discussed. Experimental results obtained from an experimental ZCT-PWM boost converter prototype implemented with several of the auxiliary circuits discussed in this paper are presented, and the results confirm the superior performance of the proposed converter     

A zero-voltage transition boost converter using a zero-voltage switching auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-voltage switching (ZVS) auxiliary switches is proposed. Various operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 300-W, 250-kHz, 300-V output DC-DC converter is presented. A modified gating scheme to utilize the auxiliary switch in the main power processing is discussed. A 600-W, 100-kHz, 380 V output, 90-250 V AC, power factor corrected, AC-to-DC, boost converter with the modified gating scheme is presented. Results show that the main switch maintains ZVT while auxiliary switches retain ZVS for the complete specified line and load conditions. Parasitic oscillations existing in the converters proposed in the literature are completely removed.     

A passive lossless snubber cell for nonisolated PWM DC/DCconverters

A passive lossless snubber cell is proposed to improve the turn-on and turnoff transients of the MOSFETs in nonisolated pulsewidth modulated (PWM) DC/DC converters. Switching losses and EMI noise are reduced by restricting di/dt of the reverse-recovery current and dv/dt of the drain-source voltage. The MOSFET operates at zero-voltage-switching (ZVS) turnoff and near zero-current-switching (ZCS) turn-on. The freewheeling diode is also commutated under ZVS. As an example, operation principles, theoretical analysis, relevant equations, and experimental results of a boost converter equipped with the proposed snubber cell are presented in detail. Efficiency of 96% has also been measured in the experimental results reported for a 1 kW 100 kHz prototype in the laboratory, Six basic nonisolated PWM DC/DC converters (buck, boost, buck-boost, Cuk, Sepic, and Zeta) equipped with the proposed general snubber cells are also shown in this paper     

A novel active snubber for high-power boost converters

A technique which improves the performance of the boost converter by reducing the reverse-recovery-related losses in the boost switch and rectifier with an active snubber that is implemented with a minimum number of components is presented. This minimum-component-count snubber consists of a snubber inductor, an auxiliary switch, and a rectifier. The proposed technique reduces the reverse-recovery-related losses by controlling the turn-off di/dt rate of the rectifier current with the snubber inductor connected in series with the boost switch and rectifier. The voltage and current stresses of the components in the proposed active-snubber boost converter are similar to those in its conventional “hard-switched” counterpart     

Analysis and Design for a New ZVS DC–DC Converter With Active Clamping

A new zero voltage switching (ZVS) boost converter is presented in this paper. By using an auxiliary switch and a capacitor, ZVS for all switches is achieved with an auxiliary winding in one magnetic core. A small diode is added to eliminate the voltage ringing across the main rectifier diode. This clamping technique can also be utilized in other dc-dc converters, and a family of new ZVS dc-dc converter is derived. A prototype (500 W/193 kHz) is made to verify the theoretical analysis. The efficiency is higher than 94% at 90-V input at full load     

Novel zero-current-switching (ZCS) PWM switch cell minimizingadditional conduction loss

This paper proposes a new zero-current-switching (ZCS) pulsewidth modulation (PWM) switch cell that has no additional conduction loss of the main switch. In this cell, the main switch and the auxiliary switch turn on and turn off under zero-current condition. The diodes commutate softly and the reverse-recovery problems are alleviated. The conduction loss and the current stress of the main switch are minimized, since the resonating current for the soft switching does not flow through the main switch. Based on the proposed ZCS PWM switch cell, a new family of DC-to-DC PWM converters is derived. The new family of ZCS PWM converters is suitable for the high-power applications employing insulated gate bipolar transistors. Among the new family of DC-to-DC PWM converters, a boost converter was taken as an example and has been analyzed. Design guidelines with a design example are described and verified by experimental results from the 2.5 kW prototype boost converter operating at 40 kHz     

High-power-factor soft-switched boost converter

A novel implementation of the high-power-factor (HPF) boost converter with active snubber is described. The snubber circuit reduces the reverse-recovery-related losses of the rectifier and also provides zero-voltage switching for the boost switch and zero-current switching for the auxiliary switch. The performance of the proposed approach was evaluated on an 80-kHz, 1.5-kW, universal-line range, HPF boost converter. The proposed technique improves the efficiency by approximately 2% at full load and low line.     

A New Family of Zero-Current-Switching (ZCS) PWM Converters

A new family of zero-current-switching (ZCS) pulsewidth-modulated (PWM) converters which uses a new ZCS-PWM switch cell is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and all the passive semiconductor devices in the ZCS-PWM converter operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and with reduced commutation losses, these new converters have no additional current stress in comparison to the hard-switching converter counterpart. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

A new, soft-switched, high-power-factor boost converter with IGBTs

A new soft-switching technique that improves performance of the high-power-factor boost rectifier by reducing switching losses is introduced. The losses are reduced by an active snubber which consists of an inductor, a capacitor, a rectifier, and an auxiliary switch. Since the boost switch turns off with zero current, this technique is well suited for implementations with insulated-gate bipolar transistors. The reverse-recovery-related losses of the rectifier are also reduced by the snubber inductor which is connected in series with the boost switch and the boost rectifier. In addition, the auxiliary switch operates with zero-voltage switching. A complete design procedure and extensive performance evaluation of the proposed active snubber using a 1.2 kW high-power-factor boost rectifier operating from a 90 V_rms-256 V_rms input are also presented     

Soft Switching Circuit for Interleaved Boost Converters

A zero-voltage switching-zero-current switching interleaved boost converter is proposed in this paper. An active circuit branch in parallel with the main switches is added and it is composed of an auxiliary switch and a snubber capacitor. By using this interleaved converter topology, zero current turn-on and zero voltage turn-off of the main switches can be achieved and the reverse-recovery loss of boost diode can be reduced. In addition, the auxiliary switches are zero-voltage transmission during the whole switching transition. A prototype of boost converter rated at 1.2kW has been built to confirm the effectiveness of the converter     

New family of zero-current-switching PWM converters using a new zero-current-switching PWM auxiliary circuit

A new family of zero-current-switching (ZCS) pulsewidth-modulation (PWM) converters using a new ZCS-PWM auxiliary circuit is presented in this paper. The main switch and auxiliary switch operate at ZCS turn-on and turn-off, and the all-passive semiconductor devices in the ZCS-PWM converters operate at zero-voltage-switching (ZVS) turn-on and turn-off. Besides operating at constant frequency and reducing commutation losses, these new converters have no additional current stress and conduction loss in the main switch in comparison to the hard-switching converter counterpart. The PWM switch model and state-space averaging approach is used to estimate and examine the steady-state and dynamic character of the system. The new family of ZCS-PWM converters is suitable for high-power applications using insulated gate bipolar transistors (IGBTs). The principle of operation, theoretical analysis, and experimental results of the new ZCS-PWM boost converter, rated 1.6 kW and operating at 30 kHz, are provided in this paper to verify the performance of this new family of converters.     

An improved ZCS-PWM commutation cell for IGBT's application

An improved zero-current-switching pulsewidth-modulation (ZCS-PWM) commutation cell is proposed, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches with low-current stress without voltage stress and PWM operating at constant frequency. The main advantage of this cell is a substantial reduction of the resonant current peak through the main switch during the commutation process. Therefore, the RMS current through it is very close to that observed in the hard-switching PWM converters. Also, small ratings auxiliary components can be used. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principles, theoretical analysis, design guidelines and a design example are described and verified by experimental results obtained from a prototype operating at 40 kHz, with an input voltage rated at 155 V and 1 kW output power. The measured efficiency of the improved ZCS-PWM boost converter is presented and compared with that of hard-switching boost converter and with some ZCS-PWM boost converters presented in the literature. Finally, this paper presents the application of the proposed soft-switching technique in DC-DC nonisolated power converters     

A technique for reducing rectifier reverse-recovery-related lossesin high-power boost converters

A circuit technique that reduces the boost power converter losses caused by the reverse-recovery current of the rectifier is described. The losses are reduced by inserting an inductor in the series path of the boost switch and a rectifier to control the di/dt rate of the rectifier during its turn off. The energy from the inductor after the boost switch turn off is returned to the input or delivered to the output via an active snubber