Design and computational analysis of a metal hydride hydrogen storage system with hexagonal honeycomb based heat transfer enhancements-part A

In this study, design and performance analysis is carried out for a 10 kWh metal hydride based hydrogen storage system. The system is equipped with distinctive aluminium hexagonal honeycomb based heat transfer enhancements (HTE) having higher surface area to volume ratio for effective heat transfer combined with low system weight addition. The system performance was studied under different operating conditions. The optimum absorption condition was achieved at 35 bar with water at room temperature as heat transfer fluid where up to 90% absorption was completed in 7200 s. The performance of the reactor was observed to significantly improve upon the addition of the HTE network at a minimal system weight penalty.     

Simulation and optimization of hydrogen production by steam reforming of natural gas for refining and petrochemical demands in Lebanon

Steam reforming of natural gas produces the majority of the world's hydrogen (H₂) and it is considered as a cost-effective method from a product yield and energy consumption point of view. In this work, we present a simulation and an optimization study of an industrial natural gas steam reforming process by using Aspen HYSYS and MATLAB software. All the parameters were optimized to successfully run a complete process including the hydrogen production zone units (reformer reactor, high temperature gas shift reactor HTS and low temperature gas shift reactor LTS) and the purification zone units (absorber and methanator). Optimum production of hydrogen (87,404 MT/year) was obtained by fixing the temperatures in the reformer and the gas shift reactors (HTS & LTS) at 900 °C, 500 °C and 200 °C respectively while maintaining a pressure of 7 atm, and a steam to carbon ratio (S/C) of 4. Moreover, ~99% of the undesired CO₂ and CO gases were removed in the purification zone and a reduction of energy consumption of 77.5% was reached in the heating and cooling units of the process.     

Hydrogen-rich syngas production by gasification of Urea-formaldehyde plastics in supercritical water

Supercritical water is a promising medium to convert plastics into hydrogen and other recyclable products efficiently. In previous research, supercritical water gasification characteristics investigations focus on thermoplastics instead of thermoset plastics due to its chemical, thermal and mechanical stability. Urea-formaldehyde (UF) plastics were selected as a typical kind of thermoset plastics for investigation in this paper and quartz tubes were used as the reactor in order to avoid the potential catalytic effect of metal reactor wall. Conversion characteristic were studied and the influence of different operating parameters such as temperature, reaction time, feedstock mass fraction and pressure were investigated respectively. The molar fraction of hydrogen could reach about 70% in 700 °C. Products in gas phase and solid phase were analyzed, and properties, chemical structures and inhibition mechanism of thermoset plastics was analyzed after comparing with polystyrene (PS) plastics. The result showed that increase of high temperature and long reaction time could promote gasification process, meanwhile the increase in the feedstock mass fraction would result in suppression of the gasification process. Finally, kinetic study of UF was carried out and the activation energy and pre-exponential factor of the Arrhenius equation were calculated as 30.09 ± 1.62 kJ/mol and 0.1199 ± 0.0049 min⁻¹, respectively.     

Molten salt synthesis of high-entropy alloy AlCoCrFeNiV nanoparticles for the catalytic hydrogenation of p-nitrophenol by NaBH4

High-entropy alloy (HEA) AlCoCrFeNiV nanoparticles were prepared from oxide precursors using a molten salt synthesis method without an electrical supply. The oxide precursor was directly reduced by CaH₂ reducing agent in molten LiCl at 600°C-700°C or molten LiCl–CaCl₂ at 500°C-550°C. When the reduction was conducted at 700°C, a face-centered cubic (FCC) structure produced, as identified by X-ray diffraction analysis. With lower reduction temperatures, the FCC structure was absent, replaced by a body-centered cubic (BCC) structure. With a reduction temperature of 550°C, the resulting sample was composed of highly pure HEA AlCoCrFeNiV nanoparticles with a BCC structure of 15 nm. Analyses by scanning electron microscopy/transmission electron microscopy with energy-dispersive X-ray spectroscopy confirmed the formation of homogeneous HEA AlCoCrFeNiV with a nanoscale morphology. In the hydrogenation reaction of p-nitrophenol by NaBH₄, the AlCoCrFeNiV nanoparticles (produced at 550°C) exhibited a catalytic activity with ～90% conversion and 16 kJ/mol activation energy.     

Kinetics of formic acid decomposition in subcritical and supercritical water – a Raman spectroscopic study

The decomposition of formic acid is studied in a continuous sub- or supercritical water reactor at temperatures between 300 and 430 °C, a pressure of 25 MPa, residence times between 4 and 65 s, and a feedstock concentration of 3.6 wt%. In situ Raman spectroscopy is used to produce real-time data and accurately quantify decomposition product yields of H₂, CO₂, and CO. Collected spectra are used to determine global decomposition rates and kinetic rates for individual reaction pathways. First-order global Arrhenius parameters are determined as log A (s⁻¹) = 1.6 ± 0.20 and E_A = 9.5 ± 0.55 kcal/mol for subcritical decomposition, and log A (s⁻¹) = 12.56 ± 1.96 and E_A = 41.90 ± 6.08 kcal/mol for supercritical decomposition. Subcritical and supercritical Arrhenius parameters for individual pathways are proposed. The variance in rate parameters is likely due to changing thermophysical properties of water across the critical point. There is strong evidence for a surface catalyzed free-radical mechanism responsible for rapid decomposition above the critical point, facilitated by low density at supercritical conditions.     

Synthesis of binary Co–Mg–O oxide system and study of its behavior in reduction/oxidation cycling

The nanoscale Co–Mg–O oxide sample (15 wt% in terms of Co₃O₄) was prepared from the corresponding xerogel synthesized by the modified sol-gel method. The hydrolysis of as-prepared Mg(OCH₃)₂ was carried out using the aqueous solution of Co(NO₃)₂ precursor. The CoO_x nanocrystallites of about 10–20 nm in size were shown to be uniformly distributed within the MgO matrix. The reduction of Co–Mg–O in H₂ flow was found to proceed in two separate stages within the temperature ranges of 200–350 °C and 350–600 °C. The prepared binary Co–Mg–O system was demonstrated to possess completely reproducible reduction behavior in the consecutive reduction/reoxidation cycles. The phase composition of the sample exposed to both the reducing and oxidative environment was followed by an in situ X-ray diffraction analysis performed at temperatures of 25, 300, 500 and 700 °C. The determined lattice parameters for MgO (a = 4.219 Å) and Co₃O₄ (a = 8.110 Å) were found to be slightly increased as compared with the values from Powder Diffraction File, so that the formation of joint non-stoichiometric (Mg_1-xCo_x)O and (Co_3-xMg_x)O₄ phases was suggested. The strong chemical interaction of cobalt oxide with MgO matrix was also evidenced by the data of a diffuse reflectance UV–vis spectroscopy.     

System optimization for effective hydrogen production via anaerobic digestion and biogas steam reforming

To construct a system for the effective hydrogen production from food waste, the conditions of anaerobic digestion and biogas reforming have been investigated and optimized. The type of agitator and reactor shape affect the performance of anaerobic digestion reactors. Reactors with a cubical shape and hydrofoil agitator exhibit high performance due to the enhanced axial flow and turbulence as confirmed by simulation of computational fluid dynamics. The stability of an optimized anaerobic digestion reactor has been tested for 60 days. As a result, 84 L of biogas is produced from 1 kg of food waste. Reaction conditions, such as reaction temperature and steam/methane ratio, affect the biogas steam reforming reaction. The reactant conversions, product yields, and hydrogen production are influenced by reaction conditions. The optimized reaction conditions include a reaction temperature of 700 °C and H₂O/CH₄ ratio of 1.0. Under these conditions, hydrogen can be produced via steam reforming of biogas generated from a two-stage anaerobic digestion reactor for 25 h without significant deactivation and fluctuation.     

Demonstration of a single-stage metal hydride hydrogen compressor composed of BCC V40TiCr alloy

In this study, demonstration of a one-stage metal hydride hydrogen compressor (MH compressor) by using a BCC alloy was performed. It was estimated that V₄₀Ti₂₂Cr₃₈ could compress approximately 1.6 wt% of hydrogen from 1.0 to 10 MPa in 20–140 °C temperature range from equilibrium theory via pressure-composition-isotherm measurements. For demonstration of an actual MH compressor, a kg-scale experimental system was set up; V₄₀Ti₂₂Cr₃₈ (1.4 kg) was introduced into a 1-inch cylindrical vessel with a heat-medium flow tube outside. As a result, 1.0 MPa of hydrogen can be compressed into the hydrogen cylinder at >10 MPa by hydrogen absorption at 10 °C and desorption at 160 °C for 30 min each (1 cycle/h) to achieve a compression rate of 0.23 Nm³/h and indicate the potential of the practical MH compressors by using BCC alloy.     

3D multiphysics modeling aided APU development for vehicle applications: A thermo-structural investigation

Solid oxide fuel cells (SOFC) are suitable for on-board electricity generation as Auxiliary Power Unit (APU) to support the electric power supply in heavy-duty vehicles. In order to satisfy the requirements of a lightweight fuel cell stack for mobile applications, thin-walled components must be used for the stack structure. This necessity is associated with material, process and design difficulties that must be solved in order to achieve a successful utilization. In this work a novel lightweight SOFC stack design with metal-supported cell was studied both numerically and experimentally. The metallic components are made from the Intermediate Temperature Metal (ITM), a high performance, high chromium ferritic stainless steels alloy. The multiphysics modeling approach (fluid dynamics, heat transfer, structural mechanics) was utilized in this work to predict the temperature distribution and the thermo-structural behavior of the new developed design. Geometric details of the fuel cell stack components as well as appropriate nonlinear, temperature and time-dependent constitutive models were developed to describe the material behavior. Experimental data were used to determine the material model parameters and validated the simulation results. The three-dimensional stress and deformation distributions in the individual stack components were evaluated and their maximum values for elements at risk were identified. Thus, the developed model enables the investigation of sustainability and serviceability of the structural elements to ensure a reliable operation of the stack. The developed computational model can be used as a design tool for parametric studies and optimization analysis to investigate the effects of process boundary conditions, material properties as well as geometrical design parameters and their variation on the induced thermal stresses.     

Effect of introducing manganese as additive on microstructure,hydrogen storage properties and rate limiting step of Ti–Cr alloy

TiCr₂ with adding different amount of Mn (0, 2, 4 and 8 wt.%) alloys have been investigated. All alloys have C14-type main phase (gray color in SEM) and Ti minor phase (dark gray color in SEM). Rietveld fitting results proved that the lattice parameter a and cell volume of C14-type phase decreased with increasing Mn content. The first hydrogenation measurement manifest that all alloys have best activation properties and could be activated without any prior heat treatment and hydrogen exposure. However, introducing Mn led to the decrease of the first hydrogen absorption rate of TiCr₂ alloy, which may be due to the decrease of cell volume of C14-type main phase. The first hydrogenation properties at low temperature and effect of air exposure of the alloy were discussed. The results showed that the maximum hydrogen absorption capacity at 0 °C was obviously higher than that at room temperature. In addition, TiCr₂ alloy doped with minor amounts of Mn after long-time air exposure showed better hydrogenation performance. This may be due to the Mn additive acting as a deoxidizer. Finally, the first hydrogenation kinetic mechanisms of all alloys at different temperature were also studied by using the rate limiting step.     

Production of hydrogen enriched syngas from municipal solid waste gasification with waste marble powder as a catalyst

Marble processing leads to the production of high amount of waste marble powder (WMP) as a byproduct, which can be a potential health risk and has hazardous impacts on the surrounding environment. However, marble is composed of calcite making it suitable for the calcium-based catalyst. Moreover, no study has been carried out to utilize this WMP in municipal solid waste (MSW) gasification process. Therefore, there is a need to address its utilization as a potential catalyst/sorbent in the gasification of municipal solid waste (MSW). A laboratory scale batch-type fixed bed reactor was used to study the effect of WMP addition on the CO₂ adsorption, steam reforming capability and char gasification in the presence of steam. Produced gas composition, gas yield, carbon conversion efficiency and tar yield were examined at different WMP to MSW ratios. Effect of temperature and steam rate varying from 700 to 900 °C and 2.5–10 ml/min respectively were also considered in this study. WMP showed a good capacity towards hydrogen enriched syngas production as well as CO₂ adsorption and tar reforming. The H₂ concentration increased significantly with an increase in the WMP to MSW mass ratio, while CO₂ decreased. A significant effect of temperature and steam rate was also observed on the produced gas composition, gas yield, and tar content. This study helps us to understand the effect of WMP addition in MSW gasification process and thus assists in the industrial application.     

Valorisation of lignocellulosic biomass investigating different pyrolysis temperatures

Presently, sugarcane bagasse (SB) and oat hulls (OH) have a distinctive potential as a renewable source of biomass, due to its global availability, which is advantageous for producing liquid and gaseous fuels by thermochemical processes. Thermo-Catalytic Reforming (TCR) is a pyrolysis based technology for generating energy vectors (char, bio-oil and syngas) from biomass wastes. This work aims to study the conversion of SB and OH into fuels, using TCR in a 2 kg/h continuous pilot-scale reactor at different pyrolysis temperatures. The pyrolysis temperatures were studied at 400, 450 and 500 °C, while the subsequent reforming temperature remained constant at 500 °C. The bio-oil contained the highest calorific value of 33.4 and 33.5 MJ/kg for SB and OH, respectively at 500 °C pyrolysis temperature, which represented a notable increase compared to the raw material calorific value of SB and OH (16.4 and 16.0 MJ/kg, respectively), this was the result of deoxygenation reactions occurring. Furthermore, the increment of the pyrolysis temperature improved the water content, total acid number (TAN), viscosity and density of the bio-oil. The syngas and the biochar properties did not change significantly with the increase of the pyrolysis temperature. In order to use TCR bio-oil as an engine fuel, it is necessary to carry out some upgrading treatments; or blend it with fossil fuels if it is to be used as a transportation fuel. Overall, TCR is a promising future route for the valorisation of lignocellulosic residues to produce energy vectors.     

Biomass gasification coupled with producer gas cleaning,bottling and HTS catalyst treatment for H2-rich gas production

The aim of the present study is to demonstrate the production of hydrogen-rich fuel gas from J. curcas residue cake. A comprehensive experimental study for the production of hydrogen rich fuel gas from J. curcas residue cake via downdraft gasification followed by high temperature water gas shift catalytic treatment has been carried out. The gasification experiments are performed at different equivalence ratios and performance of the process is reported in terms of producer gas composition & its calorific value, gas production rate and cold gas efficiency. The producer gas is cleaned of tar and particulate matters by passing it through venturi scrubber followed by sand bed filter. The clean producer gas is then compressed at 0.6 MPa and bottled into a gas cylinder. The bottled producer gas and a simulated mixture of producer gas are then subjected to high temperature shift (HTS) catalytic treatment for hydrogen enriched gas production. The effect of three different operating parameters GHSV, steam to CO ratio and reactor temperature on the product gas composition and CO conversion is reported. From the experimental study it is found that, the presence of oxygen in the bottled producer gas has affected the catalyst activity. Moreover, higher concentration of oxygen concentration in the bottled producer gas leads to the instantaneous deactivation of the HTS catalyst.     

Enhanced methane production using pretreated sludge in MEC-AD system: Performance,microbial activity,and implications at different applied voltages

Although various pretreatment methods are employed to promote sludge hydrolysis and thereby promoting methane production in the subsequent microbial electrolysis cell assisted anaerobic digestion (MEC-AD) system, the questions arise are, “which pretreatment method on waste activated sludge (WAS) maximises the sludge hydrolysis and what is the optimal applied voltage on anaerobic digestion (AD) to stimulates the direct interspecies electron transfer (DIET) performance and thereby accelerating the methane production fed with pretreated WAS?” was still unanswered. Herein, firstly, a series of pretreatment methods to hydrolyse and mineralise the organic matter of WAS was performed to evaluate solubilization efficiency and thereafter, the influence of different applied voltages (0.3 V, 0.6 V, and 0.9 V) on coupled MEC-AD reactors fed with pretreated WAS was investigated to apprehend the DIET promotion for methane production. The results indicated that in MEC-AD reactors, the methane yield increased by 27.2%, 44.8%, and 37.3% when the applied voltages were 0.3 V, 0.6 V, and 0.9 V, respectively. Therefore, the alkaline-thermal pretreatment (ATP) enhanced the sludge hydrolysis in WAS, followed by an applied voltage of 0.6 V in the MEC-AD reactor fed with pretreated WAS, enhanced methane production under DIET stimulation induced by the increased abundance of electroactive microorganisms (EAM) and the advanced electron transfer. Besides, the energy balance estimation validates that with an applied voltage of 0.6 V in MEC-AD could achieve higher net energy input.     

Molecular simulation of copper based metal-organic framework (Cu-MOF) for hydrogen adsorption

Metal organic framework (MOF) are widely used in adsorption and separation due to their porous nature, high surface area, structural diversity and lower crystal density. Due to their exceptional thermal and chemical stability, Cu-based MOF are considered excellent hydrogen storage materials in the world of MOFs. Efforts to assess the effectiveness of hydrogen storage in MOFs with molecular simulation and theoretical modeling are crucial in identifying the most promising materials before extensive experiments are undertaken. In the current work, hydrogen adsorption in four copper MOFs namely, MOF-199, MOF 399, PCN-6′, and PCN-20 has been analyzed. These MOFs have a similar secondary building unit (SBU) structure, i.e., twisted boracite (tbo) topology. The Grand Canonical Monte Carlo (GCMC) simulation was carried at room temperature (298 K) as well as at cryogenic temperature (77 K) and pressures ranging from 0 to 1 bar and 0–50 bar. These temperatures and pressure were selected to comply with the conditions set by department of energy (DOE) and to perform a comparative study on hydrogen adsorption at two different temperatures. The adsorption isotherm, isosteric heat, and the adsorption sites were analyzed in all the MOFs. The findings revealed that isosteric heat influenced hydrogen uptake at low pressures, while at high pressures, porosity and surface area affected hydrogen storage capacity. PCN-6′ is considered viable material at 298 K and 77 K due to its high hydrogen uptake.     

Impact of operational conditions on development of the hydrogen-producing microbial consortium in an AnSBBR from cassava wastewater rich in lactic acid

Biohydrogen production from cassava starch wastewater was evaluated in anaerobic sequencing batch biofilm reactor (AnSBBR) using different inoculum (mixed cultures from naturally fermented wastewater and anaerobic sludge thermally treated) and feeding strategies (batch and fed-batch). The highest hydrogen productivity (2.4 LH₂ L⁻¹ d⁻¹) and yield (11.7 molH₂ kg⁻¹Carbohydrates) were verified in low and intermediate organic load rates (12 and 14 g L⁻¹ d⁻¹) and longer cycle time (4 h), respectively. The productivity was favored by fed-batch strategy, and yield by batch. The hydrogen production was verified in both inoculum sources. However, in the assays inoculated from naturally fermented wastewater, with higher organic load rate (18 g L⁻¹ d⁻¹) and intermediate cycle time (3 h) no hydrogen was observed, regardless the feeding strategy, indicating that the inhibitory effects of the indigenous microorganisms present in cassava starch wastewater were more expressive in these conditions. The operational conditions applied to hydrogen production in AnSBBR from cassava starch wastewater may influence the microflora development in the reactor. In this study three possible scenarios were verified: hydrogen-producing bacteria (HPB) growth; hydrogen-producing bacteria inhibition or coexistence between ones and lactic acid bacteria (LAB), which are autochthones of this wastewater.     

Performance analysis of metal hydride based simultaneous cooling and heat transformation system

The performance of metal hydrides based simultaneous cooling and heat transformation system (MHCHT) using a combination of La_0.9Ce_0.1Ni₅–MmNi_4.4Al_0.6–MmNi_3.7Co_0.7Mn_0.3Al_0.3 hydrides is evaluated. The MHCHT is thermodynamically analysed using statically and dynamically measured PCIs and thermodynamic properties. In addition, a set of governing equations is solved in order to study the heat and hydrogen transfer between the reaction beds. The experimental PCI measurement data are compared with the numerical results and a reasonably good agreement is observed between them. From the results, the slope and hysteresis factors are determined for further thermal analyses. It is observed that the performance parameters i.e. cooling capacity, heat transformation capacity and coefficient of performance (COP) of MHCHT are significantly decreased by 42.4%, 26.7% and 19.1% respectively when dynamic property data are considered compared to static property data. In addition, the thermodynamic cycle is analysed by considering the variation in pressure during hydrogen transfer process between the metal hydride beds.     

Hydrofluoroolefin-based mixed refrigerant for enhanced performance of hydrogen liquefaction process

Hydrogen has the highest gravimetric energy density of all fuels; however, it has a low volumetric energy density, unfavorable for storage and transportation. Hydrogen is usually liquefied to meet the bulk transportation needs. The exothermic interconversion of its spin isomers is an additional activity to an already energy-intensive process. The most significant temperature drop occurs in the precooling cycle (between ?150 °C and up to ?180 °C) and consumes more than 50% of the required energy. To reduce the energy consumption and improve the exergy efficiency of the hydrogen liquefaction process, a new high-boiling component, Hydrofluoroolefin (HFO-1234yf), is added to the precooled mixed refrigerant. As a result, the specific energy consumption of precooling cycle reduces by 41.8%, from 10.15 kWh/kg_LH2 to 5.90 kWh/kg_LH2, for the overall process. The exergy efficiency of the proposed case increases by 43.7%; however, the total equipment cost is also the highest. The inflated cost is primarily due to the added ortho-to-para hydrogen conversion reactor, boosting the para-hydrogen concentration. From the perspective of bulk storage and transportation of liquid hydrogen, the simplicity of design and low energy consumption build a convincing case for considering the commercialization of the process.     

Hydrogen production from additive-free formic acid over highly active metal organic frameworks-supported palladium-based catalysts

The metal organic frameworks (MOFs) supported Pd catalysts for H₂ generation from formic acid (FA) were synthesized in this work, via a facile excessive impregnation-low temperature reduction approach. Among the synthetic catalysts, 10% Pd/MOF-Cr (18) displayed a remarkable performance for catalyzing FA dehydrogenation in additive-free aqueous solution, and the corresponding TOF_mid achieved 537.8 h^?1 at 323 K. Furthermore, the bimetallic Ni–Pd alloy catalysts were prepared by the introduction of Ni in the subsequent work. Fortunately, 10% Ni_0.4Pd_0.6/MOF-Cr was found to be a highly active and fairly durable catalyst, exhibiting a TOF_mid as high as 737.9 h^?1 at 323 K with almost 100% X_FA (final) and S_H2, and remained 94% of its original activity in the third cyclic catalysis. Meanwhile, Ni was discovered to be indispensable in increasing the electron density of Pd, downsizing the immobilized metal particles and inhibiting the agglomeration of the loaded nanoparticles.     

Facile modified polyol synthesis of FeCo nanoparticles with oxyhydroxide surface layer as efficient oxygen evolution reaction electrocatalysts

The oxygen evolution reaction (OER) at anode requires high overpotential and is still challenging. The metallic core-oxyhydroxide layer structure is an efficient method to lower an overpotential. We synthesized Fe rich FeCo core-Co rich FeCo oxyhydroxide layer with a different particle size of 173 nm, 225 nm, and 387 nm (FeCo 173, 225, 387) through a difference in the reduction rate of Fe/Co precursors using facile modified polyol synthesis. To investigate the effect of conductivity, CoFe₂O₄ nanoparticles of 80–130 nm were synthesized. Among samples, FeCo 173 showed remarkable catalytic performance of 316 mV at a current density of 10 mA/cm² in 0.1 M KOH compared to RuO₂ (408 mV), FeCo 225 (323 mV), FeCo 387 (334 mV), CoFe₂O₄ (382 mV). Moreover, FeCo 173 showed good stability for 60,000 s while RuO₂ showed a gradual increase in overpotential to maintain 10 mA/cm² after 15,000 s in chronopotentiometry. The excellent performance was attributed to Fe-rich metallic core, a small amount of Fe doping into CoOOH, and the synergic effect between the active site of Co rich FeCoOOH and conductive Fe rich metallic core. Following this result, it shows that the use of such FeCo electrodes has advantages in the production of hydrogen via electrochemical water oxidation.