Effect of hydrogen enrichment in the intake air of diesel engine fuelled with honge biodiesel blend and diesel

In the current investigation, the enrichment of hydrogen with the honge biodiesel blend and diesel is used in a compression ignition engine. The biodiesel is derived from the honge oil and mixed with diesel fuel by 20% (v/v). Thereafter, hydrogen at different volume flow rates (10 and 13 lpm) is introduced into the intake manifold. The outcomes by enrichment of hydrogen on the performance, combustion and emission characteristics are investigated by examining the brake thermal efficiency, fuel consumption, HC, CO, CO₂, NOₓ emissions, in-cylinder pressure, combustion duration, and rate of heat release. The engine fuelled with honge biodiesel blend is found to enhance the thermal efficiency, combustion characteristics. Compare to diesel, the BTE increased by 2.2% and 6% less fuel consumption for the HB20 + 13H₂ blend. Further, reduction in the emission of exhausts gases like CO and HC by 21% and 24%, respectively, are obtained. This is due to carbon-free structure in hydrogen. Moreover, due to high pressure in the cylinder, there is a slight increase in oxides of nitrogen emission compare to diesel. The combustion characteristics such as rate of heat release, combustion duration, and maximum ₂rate of pressure rise and in-cylinder pressure are high due to hydrogen.     

Experimental and computational study on the enhancement of engine characteristics by hydrogen enrichment in a biogas fuelled spark ignition engine

Limitations on the upgradation of biogas to biomethane in terms of cost effectiveness and technology maturity levels for stationary power generation purpose in rural applications have redirected the research focus towards possibilities for enhancement of biogas fuel quality by blending with superior quality fuels. In this work, the effect of hydrogen enrichment on performance, combustion and emission characteristics of a single-cylinder, four-stroke, water-cooled, biogas fuelled spark-ignition engine operated at the compression ratio of 10:1 and 1500 rpm has been evaluated using experimental and computational (CFD) studies. The percentage share of hydrogen in the inducted biogas fuel mixture was increased from 0 to 30%, and engine characteristics with pure methane fuel was considered as a baseline for comparative analysis. The CFD model is developed in Converge CFD software for a better understanding on combustion phenomenon and is validated with experimental data. In addition, the percentage share of hydrogen enrichment which would serve as a compromise between biogas upgradation cost and engine characteristics is also identified. The results of study indicated an enhancement in combustion characteristics (peak in-cylinder pressure increased; COV_IMEP reduced from 9.87% to 1.66%; flame initiation and combustion durations reduced) and emission characteristics (hydrocarbon emissions reduced, and NOx emissions increased but still lower than pure methane) with increase in hydrogen share from 0 to 30% in biogas fuelled SI engine. Flame propagation speed increased and combustion duration reduced with hydrogen supplementation and the same was evident from the results of the CFD model. Performance of the engine increased with increase in hydrogen share up to 20% and further increment in hydrogen share degraded the performance, owing to heat losses and the enhancement in combustion characteristics were relatively small. Overall, it was found that 20% blending of hydrogen in the inducted biogas fuel mixture will be effective in enhancing the engine characteristics of biogas fuelled engines for stationary power generation applications and it holds a good compromise between biogas upgradation cost and engine performance.     

An experimental study on the effect of hydrogen enrichment on diesel fueled HCCI combustion

This paper experimentally investigates the influence of hydrogen enrichment on the combustion and emission characteristics of a diesel HCCI engine using a modified Cooperative Fuel Research (CFR) engine. Three fuels, n-heptane and two middle distillates with cetane numbers of 46.6 and 36.6, are studied.The results show that hydrogen enrichment retards the combustion phasing and reduces the combustion duration of a diesel HCCI engine. Besides, hydrogen enrichment increases the power output and fuel conversion efficiency, and improves the combustion stability. However, hydrogen enrichment may narrow the operational compression ratio range and increase the knocking tendency. Both the overall indicated specific CO emissions (isCO) and CO emissions per unit burned diesel fuel mass are reduced by hydrogen enrichment. Although hydrogen enrichment decreases the overall indicated specific unburned hydrocarbon emissions (isHC), it does not significantly affect the HC emissions per unit burned diesel fuel mass.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Experimental evaluation of hydrogen enrichment in a dual-fueled CRDI diesel engine

The influence of hydrogen enrichment on the dieselengine fueled with diesel and palm biodiesel blend (P20) is investigated in this study. The hydrogen is injected into the intake manifold at different flow rates of 7 lpm and 10 lpm for each loading condition of 30%, 60%, 80%, 90%, and 100%, respectively. Hydrogen enrichment improves the BTE and BSEC due to its high calorific value and decreases emissions like HC, CO, and CO₂ due to its carbon-free structure. However, due to a rise in EGT, NO_x emission has increased. With the addition of hydrogen, combustion properties such as in-cylinder pressure (ICP), heat release rate (HRR), and ignition delay (ID) improve while the combustion duration (CD) drops. Compared to P20 fuel,P20 + 10H₂ has a 28% increase in BTE and a 20% decrease in BSEC at 90% load. Similarly, HC, CO, and CO₂ emissions decrease by 16%, 35%, and 12%, while NO_x emission increases by 13% compared to P20. At full load, P20 + 10H₂increasesin-cylinder pressureand heat release ratebyupto 1–5%, while CD decreases by 12.5% compared to the P20 blend.     

Numerical investigation on hydrogen-diesel dual-fuel engine improvements by oxygen enrichment

Hydrogen-diesel dual fuel (HDDF) technology is one approach available to improve the performance and reduce carbon-based emissions of compression ignition (CI) engines. Unfortunately, when operated at partial and low loads, HDDF engine configurations suffer from poor fuel utilization, combustion efficiency and ignition delay. As partial load application is increasingly important to performance of hybrid power systems, this paper explores the use of oxygen enrichment to improve HDDF performance outside of conventional load applications.In this paper, a numerical model was first developed and validated for HDDF combustion using experimental data. This model was subsequently applied to study the influences of oxygen enrichment on engine performance and emission characteristics. Furthermore, the Exhaust Gas Recirculation (EGR) was implemented as a secondary control for NOx emission reduction. For this configuration the results showed that oxygen enrichment (between 21% and 27% by volume) into the intake manifold led to an improved combustion efficiency and reduced carbon-based emissions. The brake thermal efficiency (BTE) increased by 1.6% and the brake specific energy consumption decreased by 4%. Across the emissions spectrum, soot emission reduced by 72%, whereas NOx emission increased by 63% without using the EGR technique. By combining oxygen enrichment and EGR strategies, a considerable reduction of 79% in NOx and an increase of 2.6% in BTE was observed for the oxygen concentration of 27% and EGR rate of 24% compared to a conventional HDDF operation with 45% HES ratio.     

Investigations on the influence of ethanol and water injection techniques on engine's behavior of a hydrogen - biofuel based dual fuel engine

This work explores the influence of hydrogen and ethanol on improving engine's behavior of Maduca longifolia oil (MO) based dual fuel diesel engine. A mono cylinder diesel engine was tested in dual fuel mode of operation at the rated power output of 3.7 kW under variable hydrogen energy shares from 0 to the maximum allowable limit (until severe knocking i.e. upto 20%). The knock limit was further extended by injecting water and ethanol at the intake manifold and the engine's performance, emission and combustion characteristics were analyzed. In addition ethanol was also injected and introduced along with the intake air for comparison with hydrogen dual fuel mode. Dual fuel operation increased the BTE from 25.2% with neat MO to a maximum of 28.5% and 30% respectively with hydrogen and ethanol for the energy share of 15% and 38% where as the BTE was 30.8% with ND. The smoke opacity was reduced from 78% with neat MO to 58% for the hydrogen energy share of 15% which is the MEP (maximum efficiency point) whereas the smoke emission was noted as 51% with ND operation. However, hydrogen induction increased the NO (nitric oxide) emission. Injection of water and ethanol at the inlet was observed to extend the knocking limit with improved BTE. The BTE reached a maximum of 30.1% with 5% water and 30.8% with 10% ethanol injection. The MEPs were arrived as 31% and 30% hydrogen energy shares respectively with 5% water and 10% ethanol injection. It was concluded that hydrogen induction can be very effective in improving the diesel engine's performance when using MO as base fuel when operating on dual fuel mode. The performance could be improved by extending the knock limit by injecting ethanol and water along with hydrogen.     

Research of performance and emission indicators of the compression-ignition engine powered by hydrogen - Diesel mixtures

The purpose of this study is to use the hydrogen – diesel mixture in Audi/VW 1.9 TDI turbocharged CI engine equipped with dynamometer and examine the performance and emission indicators by comparing it with sole diesel mode. The recent diesel emission scandals because of manufacturers cheating the laboratory tests, have initiated the discussions about the sustainable and environmentally friendly diesel engines. The CI engine without major engine modifications was set to operate at two speeds of 1900 rpm and 2500 rpm. At each of speed, the experiment was conducted at three BMEP: 0.4 MPa, 0.6 MPa, and 0.8 MPa. The test engine was operated using diesel fuel with amounts of 10 l/min, 20 l/min, and 30 l/min of hydrogen gas, supplied with air into intake manifold before the turbocharger. Relatively low hydrogen fraction (max. 15.74%) has effect on diesel combustion process and performance indicators at the all range of BMEP. The in-cylinder peak pressure at both speeds of 1900 rpm and 2500 rpm was lower than that with pure diesel fuel, as the small amount of hydrogen shortens the CI engine ignition delay period and decreases the rate of pressure rise. The decrease of BTE noticed, and increase of BSFC was registered with low hydrogen fraction (hydrogen amounts of 10 l/min, 20 l/min). However, with increase of hydrogen amount to 30 l/min, the BTE increased and BSFC decreased to the level, which was lower than that at the pure diesel test. The supply of hydrogen positively effects on engine emissions: the smokiness, NO_x, CO₂, CO decreased, the only hydrocarbon increased. The effect of hydrogen fraction on the combustion and emission characteristics of the diesel - hydrogen mixture was validated by AVL (Anstalt für Verbrennungskraftmaschinen List) BOOST and analysed with presentations of the main limitations and perspectives.     

Experimental investigation on biogas enrichment with hydrogen for improving the combustion in diesel engine operating under dual fuel mode

Biogas valorization as fuel for internal combustion engines is one of the alternative fuels, which could be an interesting way to cope the fossil fuel depletion and the current environmental degradation. In this circumstance, an experimental investigation is achieved on a single cylinder DI diesel engine running under dual fuel mode with a focus on the improvement of biogas/diesel fuel combustion by hydrogen enrichment. In the present investigation, the mixture of biogas, containing 70% CH₄ and 30% CO₂, is blended with the desired amount of H₂ (up to 10, 15 and 20% by volume) by using MTI 200 analytical instrument gas chromatograph, which flow thereafter towards the engine intake manifold and mix with the intake air. Depending on engine load conditions, the volumetric composition of the inducted gaseous fraction is 20–50% biogas, 2–10% H₂ and 45–78% air. Near the end of the compression stroke, a small amount of diesel pilot fuel is injected to initiate the combustion of the gas–air mixture. Firstly, the engine was tested on conventional diesel mode (baseline case) and then under dual fuel mode using the biogas. Consequently, hydrogen has partially enriched the biogas. Combustion characteristics, performance parameters and pollutant emissions were investigated in-depth and compared. The results have shown that biogas enriched with 20% H₂ leads to 20% decrease of methane content in the overall exhaust emissions, associated with an improvement in engine performance. The emission levels of unburned hydrocarbon (UHC) and carbon monoxide (CO) are decreased up to 25% and 30% respectively. When the equivalence ratio is increased, a supplement decrease in UHC and CO emissions is achieved up to 28% and 30% respectively when loading the engine at 60%.     

Effect of natural gas enrichment with hydrogen on combustion characteristics of a dual fuel diesel engine

Environmental benefits are one of the main motivations encouraging the use of natural gas as fuel for internal combustion engines. In addition to the better impact on pollution, natural gas is available in many areas. In this context, the present work investigates the effect of hydrogen addition to natural gas in dual fuel mode, on combustion characteristics improvement, in relation with engine performance. Various hydrogen fractions (10, 20 and 30 by v%) are examined. Results showed that natural gas enrichment with hydrogen leads in general to an improved gaseous fuel combustion, which corresponds to an enhanced heat release rate during gaseous fuel premixed phase, resulting in an increase in the in-cylinder peak pressure, especially at high engine load (4.1 bar at 70% load). The highest cumulative and rate of heat release correspond to 10% Hydrogen addition. The combustion duration of gaseous fuel combustion phase is reduced for all hydrogen blends. Moreover, this technique resulted in better combustion stability. For all hydrogen test blends, COV_IMEP does not exceed 10%. However, no major effect on combustion noise was noticed and the ignition delay was not affected significantly. Regarding performance, an important improvement in energy conversion was obtained with almost all hydrogen blends as a result of improved gaseous fuel combustion. A maximum thermal efficiency of 32.5%, almost similar to the one under diesel operation, and a minimum fuel consumption of 236 g/kWh, are achieved with 10% hydrogen enrichment at 70% engine load.     

Effect of addition of hydrogen and TiO2 in gasoline engine in various exhaust gas recirculation ratio

The effects of hydrogen ratios on combustion and emission characteristics of gasoline engine were studied under different exhaust gas recirculation (EGR), ignition timing and ignition pressure. The test performed in a modified gasoline direct ignition engine at different hydrogen ratios of 0%, 5%, 10% and 25%. In addition, the EGR rate set to 0%, 5%, 10% and 20% to study the combustion and emission characteristics. Addition to the different hydrogen fractions, 5% of TiO₂ is added to increase the combustion characteristics with reduced emission. Regarding the results of the current study, the engine torque increases by 15% due to the addition of hydrogen in gasoline, while mechanical efficiency is improved by achieving a large throttle opening. At the same time, NOx emission decreased by 62% compared to the unmodified engine due to the influence of EGR, hydrogen ratio and high oxygen concentration TiO₂. Moreover, the emission of CO and HC also reduced due to the influence of hydrogen fuel. Additionally, few more tests are taken to monitor the effect of the injection pressure for the hydrogen fuel. Higher injection reports higher effective thermal efficiency at 4 MPa and lower NOx. Reasonable injection pressure results in shorten flame development period.     

The characteristics of waste-cooking palm biodiesel-fueled CRDI diesel engines: Effect hydrogen enrichment and nanoparticle addition

The influence of iron nanoparticle (INP) addition (75 ppm) and hydrogen enrichment (10 lpm) with waste cooking palm biodiesel blend (WCB) on a CRDI diesel engine is evaluated. A blend of 20% WCB and 80% diesel is used, and the dosing level of INP has been kept at 75 ppm, which has been decided based on the oxygen content of biodiesel. Results indicate that the combination of H₂ enrichment and INP addition improves the BTE and BSFC of biodiesel blends as that of diesel. A maximum improvement of BTE of 7.1% than that of diesel is obtained at 90% loading. The combined impact of better hydrogen combustion characteristics and improved air-fuel mixing with nanoparticles reduces CO and HC emissions by 37.5% and 41.8%, respectively, for the WCB fuel sample. However, NO_X emission shows an elevation of 27.4% compared to diesel. Combustion parameters, namely ICP (80.1 bar) and HRR (89.5 J/˚CA) indicate an improvement of 5.3% and 6.7% compared to diesel for WCB + INP + H₂. This is owing to the combination of hydrogen's rapid flame speed and INP-added biodiesel's increased thermal conductivity.     

Effect of natural antioxidant additive on hydrogen-enriched biodiesel operated compression ignition engine

The environmental degradation and depletion of fossil fuel, urges the need of renewable fuel for IC engines. Among the renewable fuel, biodiesel are widely used as alternative fuel but for recent years hydrogen is also considered as alternative fuel because of zero emission but it possess higher auto ignition temperature. In order to reduce the self-ignition temperature of hydrogen and another liquid fuel is mixed and operated as a dual fuel mode condition in CI engine. The current investigation aims to analyse the impact of natural antioxidant additive on hydrogen-enriched biodiesel operation in a diesel engine. During the experimentation process hydrogen is admitted at the intake manifold and B20 blend of juliflora biodiesel is injected in combustion cylinder. The three test fuel samples are used for the experimentation process such as diesel, B20 and B20 with hydrogen in different flow rates such as 8, 10, 12, 16,20lpm. B20 with hydrogen shows an increment of brake thermal efficiency (BTE). Among the test fuels B20 + 16lpm and B20 + 20lpm blends have better improvement of BTE of 28.815% and 28.32%, which is higher than the conventional engine at maximum load CO, HC emission is also lower for B20 + 16lpm and B20 + 20lpm than other blends but the NO_x emission increases of 26 and 28% than diesel respectively. In order to minimize the NO_x emission, natural antioxidant additive Melia Azedarach (MA) of 1000 ppm is added to B20 + 16lpm and found that B20 + 16lpm with MA shows an improvement of BTE 2.17% higher than B20 + 16lpm without additive and the NO_x emission for B20 + 16lpm with additive is 1079 ppm, which is 21.9% lower than B20 + 16lpm without additives. Therefore B20 + 16lpm with additive is superior than other test blends.     

Influence of injection timing on performance,combustion and emission characteristics of Jatropha biodiesel engine

The study of effect of injection timing along with engine operating parameters in Jatropha biodiesel engine is important as they significantly affect its performance and emissions. The present paper focuses on the experimental investigation of the influence of injection timing, load torque and engine speed on the performance, combustion and emission characteristics of Jatropha biodiesel engine. For this purpose, the experiments were conducted using full factorial design consisting of (3³) with 27 runs for each fuel, diesel and Jatropha biodiesel. The effect of variation of above three parameters on brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), peak cylinder pressure (P_max), maximum heat release rate (HRR_max), CO, HC, NO emissions and smoke density were investigated. It has been observed that advance in injection timing from factory settings caused reduction in BSFC, CO, HC and smoke levels and increase in BTE, P_max, HRR_max and NO emission with Jatropha biodiesel operation. However, retarded injection timing caused effects in the other way. At 15 N m load torque, 1800 rpm engine speed and 340 crank angle degree (CAD) injection timing, the percentage reduction in BSFC, CO, HC and smoke levels were 5.1%, 2.5%, 1.2% and 1.5% respectively. Similarly the percentage increase in BTE, P_max, HRR_max and NO emission at this injection timing, load and speed were 5.3%, 1.8%, 26% and 20% respectively. The best injection timing for Jatropha biodiesel operation with minimum BSFC, CO, HC and smoke and with maximum BTE, P_max, HRR_max is found to be 340 CAD. Nevertheless, minimum NO emission yielded an optimum injection timing of 350 CAD.     

Combustion,performances, and emissions characteristics of Hermetia illucens larvae oil in a direct injection compression ignition engine

Hermetia illucens larvae oil (HILO) is among biofuel feedstock from insects that has high potential to reduce dependency on petroleum resources. The present paper is motivated by the need to critically examine the effect of HILO mixed with diesel fuel (DF) on combustion, engine performance, and emission characteristics of a single cylinder direct injection (DI) compression ignition (CI) engine. The experiment was performed at a constant speed of 1500 rpm under various engine loads. The results revealed that the in-cylinder pressure, heat release rate (HRR), and the ignition delay (ID) were reduced by an average of 3.32%, 12.89%, and 4.36%, respectively. The brake specific fuel consumption (BSFC) and exhaust gas temperature (EGT) increased considerably at all engine loads. The brake thermal efficiency (BTE) was discovered to be lower by 11.47% compared to DF. The finding also shows that carbon monoxide (CO), carbon dioxide (CO₂), and unburned hydrocarbon (UHC) emissions increased with the addition of HILO. The nitrogen oxides (NO_x) emission reduced by 19.80% compared to DF at all the engine loads. Overall, this study concluded the potential of HILO in CI engine as a promising renewable and environmentally friendly resource for the better earth.     

Experimental research on a blended hydrogen-fuel engine

An experimental study on the performance of a single cylinder engine fueled with hydrogen/gas fule blends was carried out. The performance of engine with different fuel components under the load characteristics of the engine was analyzed. The experimental results showed that with the increase of hydrogen blending ratio, the combustion speed was accelerated, and the maximum torque and maximum pressure in the cylinder were increased; The maximum torque of blended fuel with 40% CO₂ was 68.3% of that without CO₂; The maximum pressure in cylinder of blended fuel with 40% H₂ was 1.6 times higher than that without hydrogen; When the proportion of hydrogen was more than 30%, the torque decreased; When the mixture was blended with 30% N₂, the engine torque reached the maximum at the hydrogen ratio of 15%; With the increase of hydrogen blending ratio, the emission of CO increased and the emission of HC and NOx decreased; When the hydrogen blending ratio remained unchanged, the CO emission was the largest at medium load, the HC emission was the largest at small load, and the NOx emission was the largest at high load; When the mixture was blended with 15% H₂, with the increase of the proportion of nitrogen, emission of CO decreased, emissions of HC and NOx increased. The research of this paper provided an experimental basis for the design and development of gas fuel engines.     

Effect of hydrogen fuel at higher flow rate under dual fuel mode in CRDI diesel engine

The prime intention of this work is to provide a maximum replacement for diesel using hydrogen in a common rail direct injection equipped diesel engine. The experiment was conducted upto 5.2 kW brake power constant speed water-cooled engine. In the combustion chamber, diesel fuel was injected at a crank angle of 23⁰ bTDC, making it an ignitor for the premixed mixture of hydrogen and air. Hydrogen is injected at 6 different proportions ranging from 6 to 36 liter per min (LPM). The air and hydrogen gas were mixed homogeneously using the timed manifold injection technique, which was controlled through the in-house PC based data acquisition (DAQ) program developed on data factory. The electronic control unit helps to induct the hydrogen for a period of 211⁰ CA during the suction stroke. Performance, emission and combustion studies were made with the different levels of hydrogen injection, which proves that the 30 LPM of hydrogen provide the best results. Further, 30.65% improvement was achieved in brake thermal efficiency with 23.48% decreased brake specific energy consumption. This also helped to reduce the harmful emissions like CO, CO_2, UHC and smoke by 22.3%, 14%, 32.74% and 43.86%, respectively. However, oxides of nitrogen emission level was increased by 7.3% compared to that of the diesel fuel at its maximum power output setting. The duration of the combustion also reduced due to the higher flame speed character of hydrogen. Thus, the overall results conclude that the addition of hydrogen improved the performance factors and reduced all the emission values of the common rail direct injection diesel engine at an optimum level of 30 LPM.     

Impact of hydrogen generated by splitting water with nano-silicon and nano-aluminum on diesel engine performance

Efficient utilization of hydrogen generated during the reactions of nano-silicon/water and nano-aluminum/water in internal combustion engine has been investigated in the current work. Engine performance and emission studies of formulated and stabilized nanoemulsion fuels (water in diesel W/D), nano-aluminum in water/diesel (W/DA) and water in nano-silicon/diesel (W/DS) have been compared with those of diesel. Experimental investigations showed reduction in brake specific fuel consumption (BSFC) by 21% and 37%; rise in brake thermal efficiency (BTE) by 16% and 14% when engine was fueled with W/DA and W/DS respectively. For nanoemulsion fuels an increase in induced power was also recorded. Brake mean effective pressure, BTE and NOx emission dropped for W/D due to reduced exhaust gas temperatures. Nevertheless due to elevated peak cylinder pressures and exhaust gas temperatures a marginal rise in NOx, CO, HC and radiative heat emissions was observed with W/DA and W/DS.     

Investigation on performance,combustion and emission characteristics of biodiesel - Ethanol blends with hydrogen in CI engine

The current research work focus on the utilization of hydrogen as a fuel in CI engine has been increased tremendously, since it is a zero-emission fuel. But higher self-ignition temperature than conventional fuel, makes to operate in dual fuel mode condition in CI engine. The diesel or biodiesel along with hydrogen in a CI engine results in the improvement in the performance but increase of NO. In order to minimize the NO emission, addition of ethanol with jamun B20 biodiesel blend (biodiesel-diesel-ethanol) and two ternary blends such as B20E05 and B20E10 are formed. In the present study, biodiesel along with H₂ is admitted in the CI engine. Ethanol addition reduces combustion temperature and act as cetane improver for the biodiesel. This induces better combustion of the fuel and reduce NO. The biodiesel production from jamun seed is carried out through transesterification process. H₂ of 4 lpm is allowed at the air inlet and jamun B20 blend is injected through the fuel injector. Improvement of brake thermal efficiency and increase in the NO are observed for the hydrogen with biodiesel operated CI engine. The performance and emission behaviors of CI engine done for the test samples. At full load condition (ternary blend) B20E05 assisted H₂ shows the drastic reduction of NO emission of 8.2% than B20 assist H₂ blend. In other hand emission like hydrocarbon, carbon monoxide and smoke opacity show a notable reduction for B20E05 blend assist H₂ than other test sample fuel. The thermal efficiency is 30.98% for B20E05 assist H₂ and it is 7.55% and 4.7% higher than B20 and B20E05 assist H₂ blend respectively.     

Effect of natural gas enrichment with hydrogen on combustion process and emission characteristic of a dual fuel diesel engine

The paper presents results of experimental research on a dual-fuel engine powered by diesel fuel and natural gas enriched with hydrogen. The authors attempted to replace CNG with hydrogen fuel as much as possible with a constant dose of diesel fuel of 10% of energy fraction. The tests were carried out for constant engine load of IMEP = 0.7 MPa and a rotational speed of n = 1500 rpm. The effect of hydrogen on combustion, heat release, combustion stability and exhaust emissions was analyzed. In the test engine, the limit of hydrogen energy fraction was 19%. The increase in the fraction caused an increase in the cycle-by-cycle variation and the occurrence of engine knocking. It was shown that the enrichment of CNG with hydrogen allows for the improvement in the combustion process compared to the co-combustion of diesel fuel with non-enriched CNG, where the reduction in the duration of combustion by 30% and shortening the time of achieving 50% of MFB by 50% were obtained. The evaluation of the spread of the end of combustion is also presented. For H₂ energetic share over 20%, the spread of end of combustion was 48° of crank angle. Measurement of exhaust emissions during the tests revealed an increase in THC and NO_x emissions.