High performance membrane electrode assembly with ultra-low platinum loading prepared by a novel multi catalyst layer technique

An ultra-low platinum loading membrane electrode assembly (MEA) with a novel double catalyst layer (DCL) structure was prepared by using two layers of platinum catalysts with different loadings. The inner layer consisted of a high loading platinum catalyst and high Nafion content for keeping good platinum utilization efficiency and the outer layer contained a low loading platinum catalyst with low Nafion content for obtaining a proper thickness thereby enhancing mass transfer in the catalyst layers. Polarization characteristics of MEAs with novel DCL, conventional DCL and single catalyst layer (SCL) were evaluated in a H₂–air single cell system. The results show that the performance of the novel DCL MEA is improved substantially, particularly at high current densities. Although the platinum loadings of the anode and cathode are as low as 0.04 and 0.12 mg cm⁻² respectively, the current density of the novel DCL MEA still reached 0.73 A cm⁻² at a working voltage of 0.65 V, comparable to that of the SCL MEA. In addition, the maximum power density of the novel DCL MEA reached 0.66 W cm⁻² at 1.3 A cm⁻² and 0.51 V, 11.9% higher than that of the SCL MEA, indicative of improved mass transfer for the novel MEA. Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) tests revealed that the novel DCL MEA possesses an efficient electrochemical active layer and good platinum utilization efficiency.     

Feasibility of ultra-low Pt loading electrodes for high temperature proton exchange membrane fuel cells based in phosphoric acid-doped membrane

Factors as the Pt/C ratio of the catalyst, the binder content of the electrode and the catalyst deposition method were studied within the scope of ultra-low Pt loading electrodes for high temperature proton exchange membrane fuel cells (HT-PEMFCs). The Pt/C ratio of the catalyst allowed to tune the thickness of the catalytic layer and so to minimize the detrimental effect of the phosphoric acid flooding. A membrane electrode assembly (MEA) with 0.05 mg_Ptcm⁻² at anode and 0.1 mg_Ptcm⁻² at cathode (0.150 mg_Ptcm⁻² in total) attained a peak power density of 346 mW cm⁻². It was proven that including a binder in the catalytic layer of ultra-low Pt loading electrodes lowers its performance. Electrospraying-based MEAs with ultra-low Pt loaded electrodes (0.1 mg_Ptcm⁻²) rendered the best (peak power density of 400 mW cm⁻²) compared to conventional methods (spraying or ultrasonic spraying) but with the penalty of a low catalyst deposition rate.     

A novel cathode structure with double catalyst layers and low Pt loading for proton exchange membrane fuel cells

A novel cathode structure (NCS) was developed, which consisted of an inner and an outer catalyst layer (CL). It showed an improved platinum (Pt) utilization (above 50%), a lowered CL/gas diffusion layer interfacial resistance, and a decreased mass transport polarization compared with the traditional cathode structure (TCS). A hydrogen/air proton exchange membrane fuel cell employing NCS yielded an output power density up to 0.76 W cm⁻² with cathode Pt loading as low as 0.28 mg cm⁻². The enhanced performance of NCS is attributed to synergistic effect of the two catalyst supports in outer CL, which provides abundant pores to relieve water flooding and facilitates heat-induced proton conductor migration from the inner to outer CL, forming a hydrophilic proton conduction network. Moreover, the thin and compact inner CL can meet the demand of rich active sites and catalyst migration toward the regions nearest to the membrane under high current densities.     

Effect of catalyst layer with zeolite on the performance of a proton exchange membrane fuel cell operated under low-humidity conditions

Proton exchange membrane fuel cells (PEMFCs) employ a proton conductive membrane as the separator to transport a hydrogen proton from the anode to the cathode. The membrane's proton conductivity depends on the water content in the membrane, which is affected by the operating conditions. A membrane electrode assembly (MEA) that can self-sustain water is the key component for developing a light-weight and compact PEMFC system without humidifiers. Hence, zeolite is employed to the anode catalyst layer in this study. The effect of the gas diffusion layer (GDL) materials, catalyst loading, binder loading, and zeolite loading on the MEA performance is investigated. The MEA durability is also investigated through the electrochemical impedance spectroscopy (EIS) method. The results suggest that the MEA with the SGL28BCE carbon paper, Pt loadings of 0.1 and 0.7 mg cm^?2 in the anode and cathode, respectively, Nafion-to-carbon weight ratio of 0.5, and zeolite-to-carbon weight ratio of 0.3 showed the best performance when the cell temperature is 60 °C and supplies with dry hydrogen and air from the environment. According to the impedance variation measured by EIS, the MEA with zeolite in the anode catalyst layer shows higher and more stable performance than those without zeolite.     

Sputtered Pt loadings of membrane electrode assemblies in proton exchange membrane fuel cells

The fabrication of electrodes use in proton exchange membrane fuel cells (PEMFCs) by Pt sputter deposition has great potential to increase Pt utilization and reduce Pt loading without loss of cell performance. A radio frequency (RF) magnetron sputter deposition process (RF power = 100 W and argon pressure = 10^?3 Torr) was adopted to prepare Pt catalyst layers of PEMFC electrodes. The effects of cathode Pt and Nafion loadings on membrane electrode assembly (MEA)/cell performance were investigated using cell polarization, cyclic voltammetry, AC impedance, and microstructure analysis. Among the tested MEAs with various cathode Pt loadings (0.02–0.4 mg cm^?2), the one with 0.1 mg‐Pt cm^?2 (grain size = 3.90 nm, mainly Pt(111)) exhibited the best cell performance (320 and 285 mW cm^?2 at 0.44 and 0.60 V, respectively), which was similar to or better than those of some commercial nonsputtered/sputtered electrodes with the same or higher Pt loadings. The electrode Pt utilization efficiency increased as the Pt loading decreased. A Pt loading of greater than or lower than 0.1 mg cm^?2 yielded a lower electrode electrochemical active surface (EAS) area but a higher charge transfer and diffusion resistance. Nafion impregnation (0.1 to 0.3 mg cm^?2) into the sputtered Pt layer (Pt = 0.1 mg cm^?2) noticeably increased the EAS area, consistent with the decrease of the capacitance of the electrode double layer, but did not improve MEA/cell performance, mainly because of the increase in the kinetic and mass transfer resistances associated with oxygen reduction on the cathode. Copyright © 2011 John Wiley & Sons, Ltd.     

Study of the influence of Nafion/C composition on electrochemical performance of PEM single cells with ultra-low platinum load

The electrochemical performance of membrane electrode assemblies (MEAs) with ultra-low platinum load (0.02 mg_Pt cm^?2) and different compositions of Nafion/C in the catalytic layer have been investigated. The electrodes were fabricated depositing the catalytic ink, prepared with commercial catalyst (HiSPEC 2000), onto the gas diffusion layers by wet powder spraying. The MEAs were electrochemically tested using current-voltage curves and electrochemical impedance spectroscopy measurements. The experiments were carried out at 70 °C in H₂/O₂ and H₂/air as reactant gases at 1 and 2 bar pressure and 100% of relative humidity. For all MEAs tested, power density increases when the gasses pressure is increased from 1 to 2 bar. On the other hand, power density also increased when oxygen is used instead of air as oxidant gas in cathode. The lower power density (34 mW cm^?2) and power per Pt loading (0.86 kW g_Pt^?1) corresponds to the MEA prepared without Nafion in anode and cathode catalytic layers working with hydrogen and air at 1 bar pressure as reactants gas. The MEA with 30% wt Nafion/C reached the highest power density (422 mW cm^?2) and power per Pt loading (10.60 kW g_Pt^?1) using hydrogen and oxygen at 2 bar pressure. Finally, electrode surface microstructure and cross sections of MEAs were analyzed by Scanning Electron Microscopy (SEM). Examination of the electrodes, revealed that the most uniform ionomer network surface corresponds to the electrode with 40 wt% Nafion/C, and MEA ionomer-free catalytic layer shows delamination, it leads to low electrochemical performance.     

Evaluation of titanium oxide introduction in the electrode structure for portable PEMFC applications

Polymer electrolyte membrane fuel cells (PEMFCs) are among the best candidates to power a variety of devices, especially for portable applications. In the latter case, restrictive operating conditions, such as low pressure and humidity, impose particular requirements for such systems. Hence, the optimization of the electrodes in order to operate in such harsh conditions is necessary. In this work, the influence of introducing titanium oxide (TiO₂) in the catalytic layer on the MEA performance was evaluated. TiO₂ was selected since it can act both as a mechanical reinforcement for the catalyst support, and as a catalyst for the decomposition of hydrogen peroxides, forming during the fuel cell operations. Composite electrodes containing different loadings of TiO₂ were developed, using 0.3 and 0.6 mg cm^?2 of Pt at the anode and cathode, respectively. Electrochemical studies, in terms of I–V curves, cyclic voltammetry and accelerated stress tests (ASTs), were carried out in a 25 cm² single cell. It was found that an addition of a 12 wt% of TiO₂ produced an 8% of ECSA reduction after the Accelerated Stress Tests (ASTs) compared to the 25% reduction displayed by the membrane-electrode assembly (MEA) equipped with bare Pt/C.     

The dependence of performance degradation of membrane electrode assembly on platinum loading in polymer electrolyte membrane fuel cell

The durability of membrane electrode assemblies (MEAs) with varying amounts of Pt loading on the cathode of polymer electrolyte membrane fuel cells was investigated using load cycling as an accelerated degradation test (ADT). The single-cell performance of the MEA as determined by the ADT declined by approximately 34, 48, and 78%, when cathode Pt loading in the MEA was reduced to 0.3, 0.2, and 0.1 mg cm⁻², respectively. The increase in MEA performance declined at higher cathode Pt loading conditions, and the degradation rate of MEA performance was also diminished. To characterize the electrochemical and structural properties of the MEAs, cyclic voltammograms, electrochemical impedance spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and field-emission scanning electron microscopy were utilized before and after ADT.     

Ultra-low Pt loading for proton exchange membrane fuel cells by catalyst coating technique with ultrasonic spray coating machine

This paper reports use of an ultrasonic spray for producing ultra-low Pt load membrane electrode assemblies (MEAs) with the catalyst coated membrane (CCM) fabrication technique. Anode Pt loading optimization and rough cathode Pt loading were investigated in the first stage of this research. Accurate cathode Pt coating with catalyst ink using the ultrasonic spray method was investigated in the second stage. It was found that 0.272 mg_Pt/cm² showed the best observed performance for a 33 wt% Nafion CCM when it was ultrasonically spray coated with SGL 24BC, a Sigracet manufactured gas diffusion layer (GDL). Two different loadings (0.232 and 0.155 mg_Pt/cm²) exposed to 600 mA/cm² showed cathode power mass densities of 1.69 and 2.36 W/mg_Pt, respectively. This paper presents impressive cathode mass power density and high fuel cell performance using air as the oxidant and operated at ambient pressure.     

Morphological influence of graphitic carbon nanofibers by N–F dual-doping on Pt electrocatalytic activity and stability for oxygen reduction reaction in polymer electrolyte membrane fuel cells

Morphology of carbon nanofibers significantly effects Pt nanoparticles dispersion and specific interaction with the support, which is an important aspect in the fuel cell performance of the electrocatalysts. This study emphasizes, the defects creation and structural evolution comprised due to N–F co-doping on graphitic carbon nanofibers (GNFs) of different morphologies, viz. GNF-linearly aligned platelets (L), antlers (A), herringbone (H), and their specific interaction with Pt nanoparticle in enhancing the oxygen reduction reaction (ORR). GNFs–NF–Pt catalysts exhibit better ORR electrocatalytic activity, superior durability that is solely ascribed to the morphological evolution and the doped N–F heteroatoms, prompting the charge density variations in the resultant carbon fiber matrices. Amongst, H–NF–Pt catalyst performed outstanding ORR activity with exceptional electrochemical stability, which shows only 20 mV loss in the half-wave potential whilst 100 mV loss for Pt/C catalyst on 20,000 potential cycling. The PEMFC comprising H–NF–Pt as cathode catalyst with minimum loading of 0.10 mg cm^?2, delivers power density of 0.942 W cm^?2 at current density of 2.50 A cm^?2 without backpressures in H₂–O₂ feeds. The H–NF–Pt catalyst owing to its hierarchical architectures, performs well in PEMFC at the minimized catalyst loading with outstanding stability that can significantly decrease total price for the fuel cell.     

Performance of an ultra-low platinum loading membrane electrode assembly prepared by a novel catalyst-sprayed membrane technique

Membrane electrode assemblies (MEAs) with ultra-low platinum loadings are attracting significant attention as one method of reducing the quantity of precious metal in polymer electrolyte membrane fuel cells (PEMFCs) and thereby decreasing their cost, one of the key obstacles to the commercialization of PEMFCs. In the present work, high-performance MEAs with ultra-low platinum loadings are developed using a novel catalyst-sprayed membrane technique. The platinum loadings of the anode and cathode are lowered to 0.04 and 0.12 mg cm⁻², respectively, but still yield a high performance of 0.7 A cm⁻² at 0.7 V. The influence of Nafion content, cell temperature, and back pressures of the reactant gases are investigated. The optimal Nafion content in the catalyst layer is ca. 25 wt.%. This is significantly lower than for low platinum loading MEAs prepared by other methods, indicating ample interfacial contact between the catalyst layer and membrane in our prepared MEAs. Scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS) measurements reveal that our prepared MEA has very thin anode and cathode catalyst layers that come in close contact with the membrane, resulting in a MEA with low resistance and reduced mass transport limitations.     

Experimental study of commercial size proton exchange membrane fuel cell performance

Commercial sized (16 × 16 cm² active surface area) proton exchange membrane (PEM) fuel cells with serpentine flow chambers are fabricated. The GORE-TEX® PRIMEA 5621 was used with a 35-μm-thick PEM with an anode catalyst layer with 0.45 mg cm⁻² Pt and cathode catalyst layer with 0.6 mg cm⁻² Pt and Ru or GORE-TEX® PRIMEA 57 was used with an 18-μm-thick PEM with an anode catalyst layer at 0.2 mg cm⁻² Pt and cathode catalyst layer at 0.4 mg cm⁻² of Pt and Ru. At the specified cell and humidification temperatures, the thin PRIMEA 57 membrane yields better cell performance than the thick PRIMEA 5621 membrane, since hydration of the former is more easily maintained with the limited amount of produced water. Sufficient humidification at both the cathode and anode sides is essential to achieve high cell performance with a thick membrane, like the PRIMEA 5621. The optimal cell temperature to produce the best cell performance with PRIMEA 5621 is close to the humidification temperature. For PRIMEA 57, however, optimal cell temperature exceeds the humidification temperature.     

Study on the membrane electrode assembly fabrication with carbon supported cobalt triethylenetetramine as cathode catalyst for proton exchange membrane fuel cell

An improved fabrication technique for conventional hot-pressed membrane electrode assemblies (MEAs) with carbon supported cobalt triethylenetetramine (CoTETA/C) as the cathode catalyst is investigated. The V-I results of PEM single cell tests show that addition of glycol to the cathode catalyst ink leads to significantly higher electrochemical performance and power density than the single cell prepared by the traditional method. SEM analysis shows that the MEAs prepared by the conventional hot-pressed method have cracks between the cathode catalyst layer and Nafion membrane, and the contact problem between cathode catalyst layer and Nafion membrane is greatly suppressed by addition of glycol to the cathode catalyst ink. Current density-voltage curve and impedance studies illuminate that the MEAs prepared by adding glycol to the cathode catalyst ink have a higher electrochemical surface area, lower cell ohmic resistance, and lower charge transfer resistance. The effects of CoTETA/C loading, Nafion content, and Pt loading are also studied. By optimizing the preparation parameters of the MEA, the as-fabricated cell with a Pt loading of 0.15 mg cm⁻² delivers a maximum power density of 181.1 mW cm⁻², and a power density of 126.2 mW cm⁻² at a voltage of 0.4 V.     

Enhanced membrane electrode assembly performance by adding PTFE/Carbon black for high temperature polymer electrolyte membrane fuel cell

Phosphoric acid used as a proton-conductive medium in high-temperature polymer electrolyte membrane fuel cells (HT-PEMFCs) poisons the Pt surface and prevents oxygen transport in the cathode catalyst layer. The hydrophobic binders in the catalyst not only maintain the catalyst layer structure but also control the phosphoric acid distribution. In this study, polytetrafluoroethylene (PTFE)/carbon black (Vulcan XC-72R) added to the catalyst layer generates an oxygen transport channel. The catalyst layers coated on the gas diffusion layer by the bar-coating method serve as the cathode. High PTFE content causes hydrophobicity in the catalyst layer. The membrane electrode assembly (MEA) with 6 wt% PTFE/Vulcan results in the highest peak power density (0.347 W cm⁻²) and voltage (0.653 V) at 0.2 A cm⁻². A critical reason for its high performance is having the lowest R_ct + R_mt values measured at 0.6 V and 0.4 V. These results could contribute to improving the MEA performance for HT-PEMFCs.     

Methanol-tolerant cathode electrode structure composed of heterogeneous composites to overcome methanol crossover effects for direct methanol fuel cell

A methanol-tolerant cathode electrode composed of heterogeneous composites was developed to overcome CO poisoning and large O₂ mass transfer overpotential generated by methanol crossover as well as the limitation of a single alloy catalyst with methanol-tolerance in direct methanol fuel cells (DMFCs). Two additives, PtRu black and PTFE particles, were well distributed in the Pt/C matrix of the cathode electrode, and had significant effects upon open circuit voltage (OCV) and performance. A small amount of PtRu black protected the Pt surface during the oxygen reduction reaction (ORR) by decreasing CO poisoning. In addition, hydrophobic PTFE particles reduced the O₂ mass transfer overpotential induced by water and permeated methanol in the cathode. Despite only 0.5 mg cm⁻² of metal catalysts in the cathode, the membrane electrode assembly (MEA) with 3 M methanol showed high performance (0.117 W cm⁻²), which was larger than that of the traditional MEA (0.067 W cm⁻²).     

Optimum compositions of membrane electrode assemblies (MEAs) for direct dimethyl ether fuel cell

We investigated the effects of the compositions of catalyst layers and diffusion layers on performances of the membrane electrode assemblies (MEAs) for direct dimethyl ether fuel cell. The performances of the MEAs with different thicknesses of Nafion membranes were compared in this work. The optimal compositions in the anode are: 20 wt% Nafion content and 3.6 mg cm⁻² Pt loading in the catalyst layer, and 30 wt% PTFE content and 1 mg cm⁻² carbon black loading in the diffusion layer. In the cathode, MEA with 20 wt% Nafion content in the catalyst layer and 30 wt% PTFE content in the diffusion layer presented the optimal performance. The MEA with Nafion 115 membrane displayed the highest maximum power density of 46 mW cm⁻² among the three MEAs with different Nafion membranes. Copyright © 2009 John Wiley & Sons, Ltd.     

Sublayers for Pt catalyst electrodeposition electrodes in PEMFC

The effect of sublayers on the deposited platinum (Pt) catalyst layer fabricated by electrodeposition, and on the resulting fuel cell performance, was investigated. The substrate was prepared by applying a hydrophobic sublayer, composed of polytetrafluoroethylene (PTFE) and carbon black, and a hydrophilic sublayer, composed of Nafion and glycerol, onto an uncatalyzed gas diffusion layer prior to the electrodeposition of the Pt catalyst. The hydrophilic sublayer was found to play a substantial role in the Pt electrodeposition, since the structure of the resultant Pt catalyst significantly depended on the presence of the hydrophilic sublayer, the total loading amount and the Nafion to glycerol weight ratio, which in turn affected the fuel cell performance. The hydrophobic sublayer, which did not directly contact with the plating solution, did not show as marked an effect on the Pt deposit structure compared to that of the hydrophilic sublayer, except at high PTFE to carbon black weight ratios (≥70:30). However, the suitable PTFE to carbon black weight ratio in the hydrophobic sublayer was still important for the water management, mass transport of reactant gases and ohmic resistance of the membrane electrode assembly (MEA) during fuel cell operation. In this study, a total hydrophilic loading of 0.8 mg cm⁻² with a Nafion to glycerol weight ratio of 50:50, and a PTFE to carbon black weight ratio in the hydrophobic sublayer of 30:70 was found to yield the best Pt catalyst layer for PEMFC.     

High performance of low electrocatalysts loading on CNT directly grown on carbon cloth for DMFC

This study demonstrated the feasibility of a high-performance membrane-electrode-assembly (MEA), with low electrocatalyst loading on carbon nanotubes (CNTs) grown directly on carbon cloth as an anode. The direct growth of CNTs was synthesized by microwave plasma-enhanced chemical vapor deposition using CH₄/H₂/N₂ as precursors. The cyclic voltammetry and electrochemical impedance measurements with 1 mM Fe(CN)₆^3−/4− redox reaction reveal a fast electron transport and a low resistance of charge transfer on the direct growth of CNT. The electrocatalysts, platinum and ruthenium, were coated on CNTs by sputtering to form Pt-Ru/CNTs-CC with carbon cloth for CC. Pt-Ru electrocatalysts are uniformly dispersed on the CNT, as indicated by high-resolution scanning electron microscopy (HRSEM) and transmission electron microscopy (TEM), because the nitrogen doped in the CNT acts as active sites for capturing electrocatalysts. The MEA, the sandwiched structure which comprises 0.4 mg cm⁻² Pt-Ru/CNTs-CC as the anode, 3.0 mg cm⁻² Pt black as the cathode and Nafion 117 membrane at the center, performs very well in a direct methanol fuel cell (DMFC) test. The micro-structural MEA analysis shows that the thin electrocatalyst layer is uniform, with good interfacial continuity between membrane and the gas diffusion layer.     

Enhanced catalytic properties from platinum nanodots covered carbon nanotubes for proton-exchange membrane fuel cells

An efficient fabrication method for carbon nanotube (CNT)-based electrode with a nanosized Pt catalyst is developed for high efficiency proton-exchange membrane fuel cells (PEMFC). The integrated Pt/CNT layer is prepared by in situ growth of a CNT layer on carbon paper and subsequent direct sputter-deposition of the Pt catalyst. Both scanning electron microscopy (SEM) and transmission electron microscopy (TEM) demonstrate that this Pt/CNT layer consists of a highly porous CNT layer covered by well-dispersed Pt nanodots with a narrow size distribution. Compared with conventional gas-diffusion layer assisted electrodes, the CNT-based electrode with a Pt/CNT layer acting as a combined gas-diffusion layer and catalyst layer shows pronounced improvement in polarization tests. A high maximum power density of 595 mW cm⁻² is observed for a low Pt loading of 0.04 mg cm⁻² at the cathode.     

Performance of direct methanol fuel cell using carbon nanotube-supported Pt–Ru anode catalyst with controlled composition

The performance of a single-cell direct methanol fuel cell (DMFC) using carbon nanotube-supported Pt–Ru (Pt–Ru/CNT) as an anode catalyst has been investigated. In this study, the Pt–Ru/CNT electrocatalyst was successfully synthesized using a modified polyol approach with a controlled composition very close to 20 wt.%Pt–10 wt.%Ru, and the anode was prepared by coating Pt–Ru/CNT electrocatalyst on a wet-proof carbon cloth substrate with a metal loading of about 4 mg cm⁻². A commercial gas diffusion electrode (GDE) with a platinum black loading of 4 mg cm⁻² obtained from E-TEK was employed as the cathode. The membrane electrode assembly (MEA) was fabricated using Nafion^® 117 membrane and the single-cell DMFC was assembled with graphite endplates as current collectors. Experiments were carried out at moderate low temperatures using 1 M CH₃OH aqueous solution and pure oxygen as reactants. Excellent cell performance was observed. The tested cell significantly outperformed a comparison cell using a commercial anode coated with carbon-supported Pt–Ru (Pt–Ru/C) electrocatalyst of similar composition and loading. High conductivity of carbon nanotube, good catalyst morphology and suitable catalyst composition of the prepared Pt–Ru/CNT electrocatalyst are considered to be some of the key factors leading to enhanced cell performance.