Effectiveness factor correlations from simulations of washcoat nickel catalyst layers for small-scale steam methane reforming applications

In this paper, the effectiveness factors of Ni/MgAl₂O₄ washcoat catalyst layers under steam methane reforming (SMR) conditions relevant to small-scale hydrogen production systems (1–3 bar pressure, 600–800 °C temperature, and 2–4 steam-to-carbon ratio) are numerically investigated. The effects of the washcoat properties, including the layer thickness (20–80 μm), the mean pore diameter (10–40 nm), and the volume-specific catalyst surface area (1.1–3.3 × 10⁷ m²/m³), are also considered. The simulation is conducted by fully considering the intrinsic reaction kinetics (Xu and Froment model) and multicomponent mass diffusion (Maxwell-Stefan equation). The numerically obtained effectiveness factors are presented as a function of the methane conversion ratio and effective Thiele moduli, and simple correlation equations are proposed for easy evaluation of the effectiveness factors.     

A modified method for production of hydrogen from methane

The steam–methane‐reformation (SMR) reaction has been modified by including sodium hydroxide in the reaction. It is found that the reaction: 2NaOH+CH₄+H₂O = Na₂CO₃+4H₂ takes place at much lower temperatures (300–600°C) than the SMR reaction (800–1200°C). The reaction rate is enhanced with a nickel catalyst. We have studied the effect of variously ball‐milled nickel on the reaction rate and determined the optimum particle size of the catalyst. Best results were achieved by grinding the catalyst for 2 h. Prolonged ball milling caused the nickel platelets to coalesce and grow in size decreasing the reaction rate. Copyright © 2011 John Wiley & Sons, Ltd.     

Membrane reformer module with Ni-foam catalyst for pure hydrogen production from methane: Experimental demonstration and modeling

Results of experiments and modeling of a compact (800 cm³) membrane reformer module for the production of 0.25–0.30 Nm³/h hydrogen by methane steam reforming are reported. The module consists of a two-sided composite membrane disc with a 50 μm PdAg layer and two adjacent 4 mm thick Ni foam discs (60 ppi). A nickel catalyst and a porous support were deposited on the foam discs to give the final composition of 10%Ni/10%MgO/Ni-foam. Membrane permeability by pure hydrogen was investigated, and coefficients of transverse hydrogen transport across the Ni foam to the membrane in the case of inlet binary N₂H₂ mixture were refined in order to account for concentration polarization effect into the model. Activity of the catalytic discs was measured in a differential laboratory scale reactor at a pressure of 1 bar and temperature of 400–600 °C. Modules were tested at a 8–13 bar pressure of the mixture in the reforming zone and at 1 bar of pure hydrogen under the membrane, H₂O/C = 2.5–3 and a module temperature of 550–680 °C (with and without hydrogen removal). Two modifications of the module were tested: consecutive (I-type) and parallel (II-type) flow of the reaction mixture around two sides of the membrane disc. In order to optimize construction of the module, calculations were made for revealing the effect of thickness of the PdAg membrane layer (5–50 μm), thickness of the Ni foam discs (0.5–8 mm) and temperature (600–700 °C) on the hydrogen output of the module. A comparison of the values obtained in our experiments (>1 MW/m³ and >0.7 kg(H₂)/h/m²) with the literature data reported by other authors showed that the developed modules are promising for practical application as components of a fuel processor section for mobile applications.     

A strategy of mid-temperature natural gas based chemical looping reforming for hydrogen production

Steam methane reforming (SMR) needs the reaction heat at a temperature above 800 °C provided by the combustion of natural gas and suffers from adverse environmental impact and the hydrogen separated from other chemicals needs extra energy penalty. In order to avoid the expensive cost and high power consumption caused by capturing CO₂ after combustion in SMR, natural gas Chemical Looping Reforming (CLR) is proposed, where the chemical looping combustion of metal oxides replaced the direct combustion of NG to convert natural gas to hydrogen and carbon dioxide. Although CO₂ can be separated with less energy penalty when combustion, CLR still require higher temperature heat for the hydrogen production and cause the poor sintering of oxygen carriers (OC). Here, we report a high-rate hydrogen production and low-energy penalty of strategy by natural gas chemical-looping process with both metallic oxide reduction and metal oxidation coupled with steam. Fe₃O₄ is employed as an oxygen carrier. Different from the common chemical looping reforming, the double side reactions of both the reduction and oxidization enable to provide the hydrogen in the range of 500–600 °C under the atmospheric pressure. Furthermore, the CO₂ is absorbed and captured with reduction reaction simultaneously.Through the thermodynamic analysis and irreversibility analysis of hydrogen production by natural gas via chemical looping reforming at atmospheric pressure, we provide a possibility of hydrogen production from methane at moderate temperature. The reported results in this paper should be viewed as optimistic due to several idealized assumptions: Considering that the chemical looping reaction is carried out at the equilibrium temperature of 500 °C, and complete CO₂ capture can be achieved. It is assumed that the unreacted methane and hydrogen are completely separated by physical adsorption. This paper may have the potential of saving the natural gas consumption required to produce 1 m³ H₂ and reducing the cost of hydrogen production.     

Structural design of self-thermal methanol steam reforming microreactor with porous combustion reaction support for hydrogen production

To replace the traditional electric heating mode and increase methanol steam reforming reaction performance in hydrogen production, methanol catalytic combustion was proposed as heat-supply mode for methanol steam reforming microreactor. In this study, the methanol catalytic combustion microreactor and self-thermal methanol steam reforming microreactor for hydrogen production were developed. Furthermore, the catalytic combustion reaction supports with different structures were designed. It was found that the developed self-thermal methanol steam reforming microreactor had better reaction performance. Compared with A-type, the △T_max of C-type porous reaction support was decreased by 24.4 °C under 1.3 mL/min methanol injection rate. Moreover, methanol conversion and H₂ flow rate of the self-thermal methanol steam reforming microreactor with C-type porous reaction support were increased by 15.2% under 10 mL/h methanol-water mixture injection rate and 340 °C self-thermal temperature. Meanwhile, the CO selectivity was decreased by 4.1%. This work provides a new structural design of the self-thermal methanol steam reforming microreactor for hydrogen production for the fuel cell.     

Thermodynamic analysis of hydrogen generation via oxidative steam reforming of glycerol

A thermodynamic analysis of the oxidative steam reforming of glycerol (OSRG) for hydrogen production has been carried out with Aspen plus ^TM. The reaction was investigated at ambient pressure within the carbon-to-oxygen (C/O) ratio of 0.5–3.0, steam-to-carbon (S/C) ratio of 0.5–8.0 and temperature of 400–850 °C. Higher C/O and S/C ratios favor the production of hydrogen from glycerol. The highest hydrogen selectivity is obtained at 600–700 °C. To predict the potential technical obstacles in the glycerol reforming process, the OSRG process was compared with oxidative steam reforming of ethanol (OSRE) in terms of hydrogen production, autothermal condition and carbon deposition. The selectivity to hydrogen via OSRG is lower than that via OSRE under identical conditions. To achieve autothermal reforming, higher S/C and C/O ratios are required for reforming of glycerol than for ethanol due to the higher oxygen content in a glycerol molecule. From the viewpoint of thermodynamics, the glycerol reforming is more resistant to the carbon deposition. On the basis of the thermodynamic analysis and the preliminary experimental study, suggestions were proposed to guide the development of the glycerol reforming technique.     

Refuse derived fuel hydrogasification coupled with methane steam reforming

The hydrogasification of Refuse Derived Fuel (RDF) consisting of non-recyclable plastic polymers was combined with methane steam reforming in a “hydrogen self-sustained” loop configuration. The hydrogasification unit fed by 1000 kg/h of RDF was initially modeled by Aspen plus to define best operating conditions, namely temperature, pressure and hydrogen feed flow rate. After the simulations, the temperature of the hydrogasification process has been fixed at 300 °C, the pressure at 10 bar and the hydrogen feed flow rate at 140 kg/h. The steam reforming unit operates at 850 °C while the water-gas shift is conducted at 350 °C. When all the methane produced by hydrogasification is used to feed the steam reformer, which yields H₂ that is recycled back to the hydrogasifier, the net hydrogen production is 222 kg/h with an amount of CO₂ released of 2265 kg/h. For the different process configurations adopted, the energy efficiency of the process ranges 84–89%.     

Ni supported on the CaO modified attapulgite as catalysts for hydrogen production from glycerol steam reforming

The Ni catalyst supported on CaO-modified attapulgite (CaO-ATP) were synthesized by wet impregnation method at a constant Ni metal loading (10 wt%). The catalyst was tested by carrying out a glycerin steam reforming reaction under the following conditions: 400–800 °C, W/G is 3, GHSV is 1 h⁻¹. Ni–CaO-ATP exhibited the highest hydrogen yield (85.30%) and glycerol conversion (93.71%) at 600 °C. The catalysts were characterized by N₂ adsorption/desorption, BET, XRD, H₂-TPR, TG and SEM. The results show that ATP has good resistance to carbon deposition. As an attapulgite modifier of Ni–CaO-ATP, CaO promotes the dispersion of the active component nickel species, which would promote the water gas shift reaction, leading to the improving of hydrogen yield. In addition, the addition of Ca would further enhance the inhibition of carbon deposition and prolong the life of the Ni–CaO-ATP catalyst.     

Hydrogen-rich syngas production and carbon dioxide formation using aqueous urea solution in biogas steam reforming by thermodynamic analysis

Biogas is a renewable biofuel that contains a lot of CH₄ and CO₂. Biogas can be used to produce heat and electric power while reducing CH₄, one of greenhouse gas emissions. As a result, it has been getting increasing academic attention. There are some application ways of biogas; biogas can produce hydrogen to feed a fuel cell by reforming process. Urea is also a hydrogen carrier and could produce hydrogen by steam reforming. This study then employes steam reforming of biogas and compares hydrogen-rich syngas production and carbon dioxide with various methane concentrations using steam and aqueous urea solution (AUS) by Thermodynamic analysis. The results show that the utilization of AUS as a replacement for steam enriches the production of H₂ and CO and has a slight CO₂ rise compared with pure biogas steam reforming at a temperature higher than 800 °C. However, CO₂ formation is less than the initial CO₂ in biogas. At the reaction temperature of 700 °C, carbon formation does not occur in the reforming process for steam/biogas ratios higher than 2. These conditions led to the highest H₂, CO production, and reforming efficiency (about 125%). The results can be used as operation data for systems that combine biogas reforming and applied to solid oxide fuel cell (SOFC), which usually operates between 700 °C to 900 °C to generate electric power in the future.     

The effect of different atmosphere treatments on the performance of Ni/Nb–Al2O3 catalysts for methane steam reforming

Methane steam reforming is currently the most widely used hydrogen production reaction in industry today. Ni/Nb–Al₂O₃ catalysts were prepared by treatment under H₂, N_2, and air atmosphere prior to reduction and applied for methane steam reforming reaction at low temperature (400–600 °C). The hydrogen-treated catalysts increased catalytic activity, with 55.74% methane conversion at S/C = 2, GSVH of 14400 mL g^?1 h^?1 and 550 °C. The H₂ atmosphere treatment enhanced the Ni–Nb interaction and the formation of stable, tiny, homogeneous Ni particles (6 nm), contributing to good activity and stability. In contrast, the catalysts treated with nitrogen and air showed weaker interactions between Ni and Nb species, whereas the added Nb covered the active sites, which caused the decrease in activity. Meanwhile, carbon accumulation was also observed. This work is informative for preserving small nano-sized nickel particles to enhance catalytic performance.     

Combustion characteristics of anode off-gas on the steam reforming performance

The combination of steam reforming and HT-PEMFC has been considered as a proper set up for the efficient hydrogen production. Recycling anode off-gas is energy-saving strategy, which leads to enhance the overall efficiency of the HT-PEMFC. Thus, the recycling effect of anode off-gas on steam-reforming performance needs to be further studied. This paper, therefore, investigated that the combustion of anode off-gas recycled impacts on the steam reformer, which consists of premixed-flame burner, steam reforming and water-gas shift reactors. The temperature rising of internal catalyst was affected by lower heating value of fuels when the distance between catalyst and burner is relatively short, while by the flow rate of fuels and the steam to carbon ratio when its distance is long. The concentration of carbon monoxide was the lowest at 180 °C of LTS temperature, while NG and AOG modes showed the highest thermal efficiency at LTS temperature of 220–300 °C and 270–350 °C, respectively. The optimum condition of thermal efficiency to maximize hydrogen production was determined by steam reforming rather than water gas shift reaction. It was confirmed that the condition to obtain the highest thermal efficiency is about 650 °C of steam reforming temperature, regardless of combustion fuel and carbon monoxide reduction. The difference of hydrogen yield between upper and lower values is up to 1.5 kW as electric energy with a variation of thermal efficiency. Hydrogen yield showed the linear proportion to the thermal efficiency of steam reformer, which needs to be further increased through proper thermal management.     

The coupling performance during reactive sorption enhanced reforming (ReSER) process: Simulation and experimental studies

The coupling performance of nano-CaO carbonation with the steam methane reforming (SMR) during reactive sorption enhanced reforming process (ReSER) for hydrogen production was studied by simulation and experimental evaluation. A two-dimensional axial symmetric pseudo-homogeneous mathematic model was established based on nano-CaO carbonation kinetics with the Boltzmann equation style and SMR reaction kinetics. The coupling performance was studied by varying carbonation rate constant (k_carb) and the maximum carbonation conversion (X_max) in the model. The mathematic model was numerically solved by the COMSOL Multiphysics software and experimentally evaluated using commercial nano-CaO as the CO₂ adsorbent. An average relative deviation of 3.86% of CH₄ conversion was obtained between the simulated and experimental results. The simulation results indicated the conversion of the CH₄ was improved from 88% to 95.3% by increasing k_carb from 1.6 s⁻¹ to 5.74 s⁻¹ and the period of pre-breakthrough time could be extended from 2 min to 20 min by increasing X_max from 0.3 to 0.9. CH₄ conversion of maximum 94.1% when reaction was under 650 °C and 1 bar, the highest molar fraction of H₂ of 99.7% when reaction at 600 °C and 1 bar, and the maximum enhancement factor of 45.4% was obtained at 576.3 °C, 2.8 bar.     

Optimization of hydrogen production from three reforming approaches of glycerol via using supercritical water with in situ CO2 separation

A pathway for hydrogen production from supercritical water reforming of glycerol integrated with in situ CO₂ removal was proposed and analyzed. The thermodynamic analysis carried out by the minimizing Gibbs free energy method of three glycerol reforming processes for hydrogen production was investigated in terms of equilibrium compositions and energy consumption using AspenPlus™ simulator. The effect of operating condition, i.e., temperature, pressure, steam to glycerol (S/G) ratio, calcium oxide to glycerol (CaO/G) ratio, air to glycerol (A/G) ratio, and nickel oxide to glycerol (NiO/G) ratio on the hydrogen production was investigated. The optimum operating conditions under maximum H₂ production were predicted at 450 °C (only steam reforming), 400 °C (for autothermal reforming and chemical looping reforming), 240 atm, S/G ratio of 40, CaO/G ratio of 2.5, A/G ratio of 1 (for autothermal reforming), and NiO/G ratio of 1 (for chemical looping reforming). Compared to three reforming processes, the steam reforming obtained the highest hydrogen purity and yield. Moreover, it was found that only autothermal reforming and chemical looping reforming were possible to operate under the thermal self-sufficient condition, which the hydrogen purity of chemical looping reforming (92.14%) was higher than that of autothermal reforming (52.98%). Under both the maximum H₂ production and thermal self-sufficient conditions, the amount of CO was found below 50 ppm for all reforming processes.     

Application of aspen plus to renewable hydrogen production from glycerol by steam reforming

Steam reforming is the most favored method for the production of hydrogen. Hydrogen is mostly manufactured by using steam reforming of natural gas. Due to the negative environmental impact and energy politics, alternative hydrogen production methods are being explored. Glycerol is one of the bio-based alternative feedstock for hydrogen production. This study is aimed to simulate hydrogen production from glycerol by using Aspen Plus. First of all, the convenient reactor type was determined. RPlug reactor exhibited the highest performance for the hydrogen production. A thermodynamic model was determined according to the formation of byproduct. The reaction temperature, water/glycerol molar feed ratio as reaction parameters and reactor pressure were investigated on the conversion of glycerol and yield of hydrogen. Optimum reaction parameters are determined as 500 °C of reaction temperature, 9:1 of water to glycerol ratio and 1 atm of pressure. Reactor design was also examined. Optimum reactor diameter and reactor length values were determined as 5 m and 50 m, respectively. Hydrogen purification was studied and 99.9% purity of H₂was obtained at 25 bar and 40 °C. The obtained results were shown that Aspen Plus has been successfully applied to investigate the effects of reaction parameters and reactor sizing for hydrogen production from glycerol steam reforming.     

Exploring the opportunities for carbon capture in modular,small-scale steam methane reforming: An energetic perspective

Small-scale steam methane reforming units produce more than 12% of all the CO₂-equivalent emissions from hydrogen production and, unlike large-scale units, are usually not integrated with other processes. In this article, the authors examine the hitherto under-explored potential to utilise the excess heat available in the small-scale steam methane reforming process for partial carbon dioxide capture. Reforming temperature has been identified as a critical operating parameter to affect the amount of excess heat available in the steam methane reforming process. Calculations suggest that reforming the natural gas at 850 °C, rather than 750 °C, increases the amount of excess heat available by about 28.4% (at 180 °C) while, sacrificing about 1.62% and 1.09% in the thermal and exergetic efficiency of the process, respectively. Preliminary calculations suggest that this heat could potentially be utilised for partial carbon capture from reformer flue gas, via structured adsorbents, in a compact capture unit. The reforming temperature can be adjusted in order to regulate the amount of excess heat, and thus the carbon capture rate.     

Steam reforming of simulated pre-reformed naphtha in a PdAu membrane reactor

Process intensification in a membrane reactor is an efficient and compact way to produce hydrogen. A methane-rich gas mixture that simulated the composition of pre-reformed naphtha (PRN; with a steam-to-carbon ratio of 2.7) was reformed at temperatures of 550 °C–625 °C and pressures up to 40 barg. The reactor contained commercial steam reforming catalyst and a 14.8 cm long, 2.6 μm thick Pd-1.8Au (wt. %) membrane on a porous alumina support. Methane conversions approaching 90% were obtained in the membrane reactor at a gas-hourly space velocity of 676 h^?1, compared to ≤30% conversion at the same conditions in conventional reactor mode (CM) without withdrawing hydrogen through the membrane. The results were compared to steam methane reforming (SMR) in the membrane reactor at similar conditions. The nitrogen leak through the membrane increased slowly during the testing, because of both pinhole formation and some leakage through the end seals.     

Potential to retrofit existing small-scale gasifiers through steam gasification of biomass residues for hydrogen and biofuels production

This work investigates the opportunity of retrofitting existing small-scale gasifiers shifting from combined heat and power (CHP) to hydrogen and biofuels production, using steam and biomass residues (woodchips, vineyard pruning and bark). The experiments were carried out in a batch reactor at 700 °C and 800 °C and at different steam flow (SF) rates (0.04 g/min and 0.20 g/min). The composition of the producer gas is in the range of 46–70 % H₂, 9–29 % CO, 12–27 % CO₂, and 2–6 % CH₄. A producer gas specific production factor of approx. 10 NL_pg/g_char can be achieved when the lower SFs are used, which allows to provide 80 % of the hydrogen concentration required for biomethanation and MeOH synthesis. As for FT synthesis, an optimal H₂/CO ratio of approx. 2 can be achieved. The results of this work provide further evidence towards the feasibility of hydrogen and biofuels generation from residual biomass through steam gasification.     

Improvement of the internal reforming of metal-supported SOFC at low temperatures

Automotive Solid oxide fuel cells (SOFCs) require improvements in mechanical robustness, power generation at low temperatures, and system compactness. To address these issues, we attempt to improve the internal reformation of metal-supported SOFCs (MS-SOFCs) via catalyst infiltration. After introducing nickel/gadolinium-doped ceria (Ni/GDC) nanoparticles, power densities of 1.16 Wcm⁻² with hydrogen (3%H₂O) and 0.85 Wcm⁻² with methane (Steam-to-Carbon ratio, S/C = 1.0) are obtained at 600 °C, 0.7 V. This is the highest performance achieved in previous studies on MS-SOFCs. Internal reforming with various hydrocarbon is also demonstrated. In particular 0.64 Wcm⁻² at 600 °C, 0.7 V is obtained when the fuel is iso-octane. We develop a numerical model to separately analyze reforming and electrochemical reaction. Catalyst infiltration dramatically increases the number of active sites for steam reforming. In addition, ruthenium/gadolinium-doped ceria (Ru/GDC) should be suitable as a catalyst metal at low temperatures because of the lower activation energy of steam reforming.     

Hydrogen production from acetic acid steam reforming over nickel-based catalyst synthesized via MOF process

In our earlier work, we have reported that Ni supported on γ-Al₂O₃–La₂O₃–CeO₂ (ALC) catalyst prepared via metal organic framework (MOF) was more active for acetic acid steam reforming (AASR) [1]. Here we report detailed study on the performance of this catalyst for AASR. Effects of operating conditions such as temperatures (400–650 °C), steam to carbon molar ratio (S/C) and feed flow rate (1.5–5.5 mL/h) were evaluated and optimized. Results showed an excellent activity for AASR at the molar ratio S/C = 6.5, feed flow rate = 2.5 mL/h and, at 600 °C with almost total conversion and more than 90% of H₂ yield. The ordered porous structure of embedded nickel supported catalyst promotes excellent steam reforming activity and water gas shift reaction even at low temperatures, which leads to the good stable behaviour up to 36 h of TOS. The coke formation was also significantly suppressed by ALC support. Catalyst regenerated by passing oxygen at 500 °C and followed by reduction in hydrogen also show a good activity. Catalysts were characterized by DT-TGA, XRD, TEM, H₂-TPR and N₂-adsorption-desorption to understand the micro structure and coke deposition behaviour.     

Agglomerated Co–Cr/SBA-15 catalysts for hydrogen production through acetic acid steam reforming

Hydrogen produced from renewable resources is becoming interesting as an alternative to conventional fossil fuels. Co-based catalysts have been reported for their active role in steam reforming of acetic acid as the main model compound of bio-oil aqueous fraction. In the present work, a series of Co–Cr/SBA-15 extrudates were prepared by varying the binder (bentonite) content and particle size in order to get catalyst particles suitable to be used in a steam reformer at industrial scale. Catalysts were characterized by N₂ physisorption, ICP-AES, TEM, SEM, XRD and H₂-TPR. The physicochemical characterization results showed that no remarkable changes occurs after the extruding process of the powdered sample, except for the particle size and mechanical strength. Acetic acid steam reforming tests were done at 600 °C and WHSV = 30.1 h⁻¹ varying the feed flow rate and the catalysts particle size in order to study the influence of internal and external diffusion limitations. Extruded particles with an effective diameter of 1.5 mm and 30 wt% of bentonite get similar conversion and hydrogen selectivity than powder sample. Besides, the agglomerated catalysts are also stable up to 12 h of TOS.