Enhanced hydrogen purification by graphene - Poly(Dimethyl siloxane) membrane

In this study, a nanocomposite graphene oxide (GO) incorporated poly (dimethyl siloxane) (PDMS) membrane was produced and used for the purification of hydrogen (H₂₎ by separating the (CO₂). The produced membrane was characterized and the single-gas permeability test was performed. Effects of GO addition, trans-membrane pressure and membrane thickness on the gas separation performance of membrane were evaluated as a function of permeability and CO₂/H₂ selectivity. GO addition increased the CO₂/H₂ selectivity and H₂ purification performance. The highest CO2 permeability of 3670 Barrer and CO₂/H₂ selectivity of 11.7 were obtained when the GO loading was 0.5 wt% when the trans-membrane pressure was 0.2 Mpa.     

Experimental investigation of natural polysaccharide-based mixed matrix membrane modified with graphene oxide and Pd-nanoparticles for enhanced gas separation performance

In this work, we proposed a mixed matrix membrane prepared by using a glycerol modified guar gum (GGP) polymer matrix incorporated with graphene oxide (GO). The influence of varying GO concentration on the gas separation performance was investigated and 2 wt% was found to be the optimum concentration for high performance. The 2 wt% GO mixed matrix membranes were further modified with Pd nanoparticles. When GO, and Pd nanoparticles were mixed, CO₂ permeability increased by 49.94%, while the permeability of H₂ gas molecules decreased by 98.11%, respectively, compared to the pristine GGP membrane. The selectivity of CO₂/H₂ was obtained as 18.27. The glass transition temperature of the membrane increased from 85 to 95.2 °C, tensile strength and elongation of the break were significantly improved by 29.09% and 84.37% through the addition of Pd and GO into the membrane. The scanning electron microscopy revealed a dense top surface after GO nanosheets incorporation. Further, the thermogravimetric analysis proposes that the modified membrane is thermally stable than GGP. Henceforth, the study suggests GO incorporation and Pd nanoparticles modification of guar gum membrane is a promising gas separation membrane with potentially high selectivity for CO₂ gas.     

Silica-zirconia membrane supported on modified alumina for hydrogen production in steam methane reforming unit

A hydrogen-selective and hydrothermally stable membrane composed of silica-zirconia layer deposited on a modified alumina sub layer was successfully prepared. The composite membrane was used for hydrogen purification from synthesis gas in steam methane reforming process. Silica-zirconia layer was synthesized using the CVD method at 923K and atmospheric pressure while the alumina base layer was prepared via sol-gel procedure. DLS, XRD, SEM/EDX, and BET characterization techniques were used to prove that γ-alumina base and silica-zirconia layer are fabricated successfully. Using the composite membrane, hydrogen selectivity toward other gases has improved significantly. Moreover, H₂/CH₄, H₂/CO, and H₂/CO₂ selectivity have been increased from 700, 350 and 70 in 5 h CVD synthesized membrane to 1600, 750 and 570 for 12 h CVD synthesized membrane respectively. The synthesized Silica-Zirconia membrane successfully altered gases permeability tendency order from H₂ > CH₄ > CO₂ > CO to H₂ > CO₂ > CO > CH₄ which leads to better separation of the product from methane feed. Finally, hydrothermal stability test demonstrated that permeability loss in silica-zirconia CVD coated membrane for H₂ is 45.7% after 48 h, while for silica CVD coated on the modified alumina approaches 92.5%.     

Evaluation of two gas membrane modules for fermentative hydrogen separation

The ability of (dimethyl siloxane) (PDMS) and SAPO 34 membrane modules to separate a H₂/CO₂ gas mixture was investigated in a continuous permeation system in order to decide if they were suitable to be coupled to a biological hydrogen production process. Permeation studies were carried out at relatively low feed pressures ranging from 110 to 180 kPa. The separation ability of SAPO 34 membrane module appeared to be overestimated since the effect concentration polarization phenomena was not taken into consideration in the permeation parameter estimation. On the other hand, the PDMS membrane was the most suitable to separate the binary gas mixture. This membrane reached a maximum CO₂/H₂ separation selectivity of 6.1 at 120 kPa of feed pressure. The pressure dependence of CO₂ and H₂ permeability was not considerable and only an apparent slight decrease was observed for CO₂ and H₂. The mean values of permeability coefficients for CO₂ and H₂ were 3285 ± 160 and 569 ± 65 Barrer, respectively. The operational feed pressure found to be more adequate to operate initially the PDMS membrane module coupled to the fermentation system was 180 kPa, at 296 K. In these conditions it was possible to achieve an acceptable CO₂/H₂ separation selectivity of 5.8 and a sufficient recovery of the CO₂ in the permeate stream.     

Effect of mesoporous silica modification on the structure of hybrid carbon membrane for hydrogen separation

An SBA-15/carbon molecular sieve (CMS) composite membrane, using polyetherimide as a precursor and mesoporous silica as filler, was fabricated for hydrogen separation. The effect of mesoporous SBA-15 on the gas transport properties of the composite membrane was evaluated. The permeability and selectivity coefficients of H₂, CO₂, O₂, N₂, and CH₄ were estimated for the pure CMS and SBA-15/CMS composite membranes at a feed pressure of 2-7 atm for 30 °C. The SBA-15/CMS composite membrane had a gas permeability higher than that of the pure CMS membrane, whereas its selectivity was the same. The permeability was found to be independent of pressure; this indicates that the gases are transported through the membrane by a molecular sieve mechanism. The membranes appeared to have a more microporous structure when the mesoporous silica SBA-15 was incorporated. These results concur with the hypothesis that SBA-15 improves gas diffusivity by increasing pore volume.     

High performance ZIF-8/PBI nano-composite membranes for high temperature hydrogen separation consisting of carbon monoxide and water vapor

Two types of advanced nano-composite materials have been formed by incorporating as-synthesized wet-state zeolitic imidazolate frameworks-8 (ZIF-8) nano-particles into a polybenzimidazole (PBI) polymer. The loadings of ZIF-8 particles in the two membranes (i.e., 30/70 (w/w) ZIF-8/PBI and 60/40 (w/w) ZIF-8/PBI) are 38.2 vol % and 63.6 vol %, respectively. Due to different ZIF-8 loadings, variations in particle dispersion, membrane morphology and gas separation properties are observed. Gas permeation results suggest that intercalation occurs when the ZIF-8 loading reaches 63.6 vol %. The incorporation of ZIF-8 particles significantly enhances both solubility and diffusion coefficients but the enhancement in diffusion coefficient is much greater. Mixed gas tests for H₂/CO₂ separation were conducted from 35 to 230 °C, and both membranes exhibit remarkably high H₂ permeability and H₂/CO₂ selectivity. The 30/70 (w/w) ZIF-8/PBI membrane has an H₂/CO₂ selectivity of 26.3 with an H₂ permeability of 470.5 Barrer, while the 60/40 (w/w) ZIF-8/PBI membrane has an H₂/CO₂ selectivity of 12.3 with an H₂ permeability of 2014.8 Barrer. Mixed gas data show that the presence of CO or water vapor impurity in the feed gas stream does not significantly influence the membrane performance at 230 °C. Thus, the newly developed H₂-selective membranes may have bright prospects for hydrogen purification and CO₂ capture in realistic industrial applications such as syngas processing, integrated gasification combined cycle (IGCC) power plant and hydrogen recovery.     

Phosphorylated chitosan/poly(vinyl alcohol) based proton exchange membranes modified with propylammonium nitrate ionic liquid and silica filler for fuel cell applications

In our previous work, phosphorylated chitosan was modified through polymer blending with poly(vinyl alcohol) (PVA) polymer to produce N-methylene phosphonic chitosan/poly(vinyl alcohol) (NMPC/PVA) composite membranes. The aim of this work is to further investigate the effects of a propylammonium nitrate (PAN) ionic liquid and/or silicon dioxide (SiO₂) filler on the morphology and physical properties of NMPC/PVA composite membranes. The temperature-dependent ionic conductivity of the composite membranes with various ionic liquid and filler compositions was studied by varying the loading of PAN ionic liquid and SiO₂-PAN filler in the range of 5–20 wt%. As the loading of PAN ionic liquid increased in the NMPC/PVA membrane matrix, the ionic conductivity value also increased with the highest value of 0.53 × 10^?3 S cm^?1 at 25 °C and increased to 1.54 × 10^?3 S cm^?1 at 100 °C with 20 wt% PAN. The NMPC/PVA-PAN (20 wt%) composite membrane also exhibited the highest water uptake and ion exchange capacity, with values of 60.5% and 0.60 mequiv g^?1, respectively. In addition, in the single-cell performance test, the NMPC/PVA-PAN (20 wt%) composite membrane displayed a maximum power density, which was increased by approximately 14% compared to the NMPC/PVA composite membrane with 5 wt% SiO₂-PAN. This work demonstrated that modified NMPC/PVA composite membranes with ionic liquid PAN and/or SiO₂ filler showed enhanced performance compared with unmodified NMPC/PVA composite membranes for proton exchange membrane fuel cells.     

Molecular-level mixed matrix membranes comprising Pebax and POSS for hydrogen purification via preferential CO2 removal

The molecular-level mixed matrix membranes (MMMs) comprising Pebax^® and POSS have been developed by tuning the membrane preparation process in this work. They exhibit a simultaneous enhancement in CO₂ permeability and CO₂/H₂ selectivity by optimizing the POSS content at extremely low loadings. This is mainly attributed to the large cavity of POSS itself and its effect on the segmental-level polymeric chain packing. More interestingly, the Pebax^®/POSS MMMs reveal a much higher separation performance in the mixed gas test than that in the pure gas test. The highest CO₂/H₂ selectivity reaches 52.3 accompanied by CO₂ permeability of 136 Barrer at 8 atm and 35 °C. This is due to the CO₂-induced plasticization that improves the free volume and polymer chain mobility, hence benefiting the interaction between the polymer matrix and penetrant CO₂. These features may ensure the superiority of Pebax^®/POSS molecular-level MMMs as CO₂-selective membranes in the industrial application of hydrogen purification.     

High performance composite hollow fiber membranes for CO2/H2 and CO2/N2 separation

The search for a clean energy source as well as the reduction of CO₂ emissions to the atmosphere are important strategies to resolve the current energy shortage and global warming issues. We have demonstrated, for the first time, a Pebax/poly(dimethylsiloxane)/polyacrylonitrile (Pebax/PDMS/PAN) composite hollow fiber membrane not only can be used for flue gas treatment but also for hydrogen purification. The composite membranes display attractive gas separation performance with a CO₂ permeance of 481.5 GPU, CO₂/H₂ and CO₂/N₂ selectivity of 8.1 and 42.0, respectively. Minimizing the solution intrusion using the PDMS gutter layer is the key to achieving the high gas permeance while the interaction between poly(ethylene oxide) (PEO) and CO₂ accounts for the high selectivity. Effects of coating solution concentration and coating time on gas separation performance have been investigated and the results have been optimized. To the best of our knowledge, this is the first polymeric composite hollow fiber membrane for hydrogen purification. The attractive gas separation performance of the newly developed membranes may indicate good potential for industrial applications.     

GNs/MOF-based mixed matrix membranes for gas separations

NU-1000 and graphene nanosheet (GNs) with different loadings have been used as fillers to prepare mixed matrix membranes (MMMs) with polyethersulfone (PES). The high performance of the MMMs has been successfully fabricated for the evaluation of gas separation at 1 bar and various temperatures (20, 40, 60 °C). The successful fabrication of the MMMs were confirmed by using SEM, FTIR, AFM, and XRD. The crystalline nature of GNs and NU-1000 in the MMMs are evidenced by XRD, which confirms the successful fabrication of the MMMs. In addition, the thermal stability of the MMMs was enhanced with the increase of the GNs. Separation performance of H₂ was superior to CO₂, N₂ and CH₄ separation on the MMMs which is a critical for producing energy. The best gas separation results in terms of both permeability and selectivity were obtained with 0.03% GNs and 10% NU-1000. PG3N membrane presented maximum H₂/CO₂, H₂/N₂ and H₂/CH₄ selectivity of 5, 4.2, 3.3 at 20 C, respectively. With an increase in temperature, the permeability increased, while the selectivity of all the MMMs decreased. The MMMs exhibited excellent gas separation capability, which offers unique opportunities for potential large-scale practical applications.     

Preparation of mixed matrix composite membrane for hydrogen purification by incorporating ZIF-8 nanoparticles modified with tannic acid

The incompatibility between nanofillers and polymer, caused by the agglomeration of nanoparticles and their weak interaction with each other, is still a challenge to develop mixed matrix composite membrane. Herein, we introduced the ZIF-8-TA nanoparticles synthesized by in situ hydrophilic modification into the hydrophilic poly(vinylamine) (PVAm) matrix to prepare composite membranes for H₂ purification. The dispersion of ZIF-8 in water was improved by tannic acid modification, and the compatibility between ZIF-8 particles and PVAm matrix was enhanced by chemical crosslinking between the quinone groups in oxidized tannic acid (TA) and the amino groups in PVAm. Moreover, the compatibility between hydrophobic polydimethylsiloxane (PDMS) gutter layer and hydrophilic separation layer was achieved by the adhesion of TA-Fe³⁺ complex to the surface of PDMS layer during membrane preparation. The interlayer hydrophilic modification and the formation of separation layer were accomplished in one step, which simplified the preparation process. The experimental results indicated that when the TA addition used for modification was 0.5 g and the ZIF-8-TA_0.5 content in membrane was 12 wt%, the prepared membrane showed the best separation performance with the CO₂ permeance of 987 GPU and the CO₂/H₂ selectivity of 31, under the feed gas pressure of 0.12 MPa.     

Development of hydrogen selective microporous PVDF membrane

Hydrogen is a sustainable clean and green energy source used to eliminate the problem of greenhouse effect. In the present work, the feasibility of gas permeability in separation of H₂ from CO₂ and N₂ have been examined using polyvinylidene fluoride (PVDF) membranes synthesised in our laboratory by the phase inversion process. Effect of various non-solvent additives, such as lithium chloride (LiCl) and Tetraethoxysilane (TEOS) in the PVDF dope solution, have been studied. The resulted asymmetric flat sheet microporous hydrophobic membrane, shows higher hydrogen permeability and selectivity over other gases (CO₂ & N₂). It has been observed that the MT5 membrane has shown the highest selectivity for hydrogen in comparison to CO₂ and N₂. The highest value of selectivity was obtained as 4.8 and 3.7 in case of H₂/CO₂ and H₂/N₂ respectively. The permeability of membrane has been obtained in the range of 2.3–4.2 mega barrer. SEM analysis is used for the investigation of membrane surface morphology.     

New PEEK-WC and PLA membranes for H2 separation

The potentialities of PEEK-WC (thermally treated at 120 °C) and PLA polymers have been studied in the field of membrane technology applied to H₂ separation/purification. In particular, for low/medium temperature operation (80 °C), PEEK-WC membranes (66 μm thick) showed good results in terms of H₂/CH₄ separation, showing an ideal selectivity value higher than 40. Meanwhile, we observed interesting selectivity also for H₂/N₂ and H₂/CO₂ separation, reaching values of 24 and 20, respectively. As expected, for PEEK-WC thermally treated membranes, the H₂ permeating flux increased from 25 to 80 °C and by increasing the transmembrane pressure. Furthermore, H₂ permeability at 80 °C was around 20 barrer. Concerning PLA membranes (26 μm thick), it is worth of noting that this polymer was pioneeristically used in this work as membrane application, showing great results in terms of H₂/CO₂ separation. Indeed, we overcame the Robeson's upper-bound (2008), achieving an ideal selectivity H₂/CO₂ around 25 with an H₂ permeability of 25 barrer. Further advantage due to the utilization of PLA membranes was related to the temperature operations set at ambient conditions, constituting a valuable and cost-effective solution for H₂/CO₂ separation processes via polymeric membrane technology.     

In situ fabrication of cross-linked PEO/silica reverse-selective membranes for hydrogen purification

Targeting at hydrogen purification, cross-linked organic–inorganic reverse-selective membranes containing poly(ethylene oxide) (PEO) are fabricated in situ by using functional oligomers (O,O′-bis(2-aminopropyl) polypropylene glycol-block-polyethylene glycol-block-polypropylene glycol: Jeffamine^® ED-2003) with a high content of PEO and epoxy-functional silanes (3-glycidyloxypropyltrimethoxysilane: GOTMS). Changes in physicochemical properties due to varying silica content have been characterized; including a great decline in melting temperature; an improvement in glassy and degradation temperature, and the suppression of PEO crystallinity. The strong affinity between quadrupolar CO₂ and polar ethylene oxide (EO) groups enhances the CO₂/H₂ separation performance of hybrid membranes, which can be further tuned by controlling the organic/inorganic ratio. The organic–inorganic hybrid membrane with 90 wt% of ED-2003 demonstrates an appealing CO₂ permeability of 367 Barrer with an attractive CO₂/H₂ selectivity of 8.95 at 3.5 atm and 35 °C. The transport performance trend with composition variations is explained by analyzing the calculated solubility and diffusivity based on the solution-diffusion mechanism. Moreover, CO₂ permeability increases with applied pressure in pure gas tests because of CO₂ plasticization phenomena, which is beneficial for CO₂/H₂ separation. Attributing to CO₂ plasticization and CO₂ dominant sorption, the mixed gas test results of the membrane containing only 25 wt% ED-2003 show greatly improved CO₂/H₂ selectivity of 13.2 with CO₂ permeability of 148 Barrer at 35 °C compared to pure gas results. Interestingly, at a stipulated CO₂ pressure, the inherent tension in cross-linked networks maintains the CO₂ permeability stable with the time. The cross-linked organic–inorganic membranes with enhancements in mechanical and thermal properties are promising for industrial-scale hydrogen purification.     

CO2-selective membranes for hydrogen purification and the effect of carbon monoxide (CO) on its gas separation performance

Industrial hydrogen production may prefer CO₂-selective membranes because high-pressure H₂ can therefore be produced without additional recompression. In this study, high performance CO₂-selective membranes are fabricated by modifying a polymer–silica hybrid matrix (PSHM) with a low molecular weight poly(ethylene glycol) dimethyl ether (PEGDME). The liquid state of PEGDME and its unique end groups eliminate the crystallization tendency of poly(ethylene glycol) (PEG). The methyl end groups in PEGDME hinder hydrogen bonding between the polymer chains and significantly enhance the gas diffusivity. In pure gas tests, the membrane containing 50 wt% additive shows CO₂ gas permeability and CO₂/H₂ selectivity of 1637 Barrers and 13 at 35 °C, respectively. In order to explore the effect of real industrial conditions, the gas separation performance of the newly developed membranes has been studied extensively using binary (CO₂/H₂) and ternary gas mixtures (CO₂/H₂/carbon monoxide (CO)). Compared to pure gas performance, the second component (H₂) in the binary mixed gas test reduces the CO₂ permeability. The presence of CO in the feed gas stream decreases both CO₂ and H₂ permeability as well as CO₂/H₂ selectivity as it reduces the concentration of CO₂ molecules in the polymer matrix. The mixed gas results affirm the promising applications of the newly developed membranes for H₂ purification.     

Development of a H2-permeable Pd60Cu40-based composite membrane using a reverse build-up method

A new reverse build-up method is developed to fabricate an economical H₂-permeable composite membrane. Sputtering and electroplating are used for the formation of a membrane comprised of a 3.7-μm-thick Pd₆₀Cu₄₀ (wt.%) alloy layer and a 13-μm-thick porous Ni support layer, respectively. The H₂-permeation measurements are performed under the flow of a gaseous mixture of H₂ and He at 300–320 °C and 50–100 kPa of H₂ partial pressure. The H₂/He selectivity values exceed 300. The activation energy at 300–320 °C is 10.9 kJ mol⁻¹. The H₂ permeability of the membrane is 1.25 × 10⁻⁸ mol m⁻¹ s⁻¹ Pa^−0.5 at 320 °C after 448 h. The estimated Pd cost of the proposed membrane is approximately 1/8 of the cost for a pure Pd₆₀Cu₄₀ membrane. This study demonstrates that the proposed method allows the facile production of low-cost, Pd-based membranes for H₂ separation.     

Highly selective high-silica SSZ-13 zeolite membranes for H2 production from syngas

A highly CO₂-selective high-silica SSZ-13 zeolite membrane was used for H₂ production by separating CO₂ from syngas (CO₂/H₂ mixture). High-silica SSZ-13 zeolite membranes were fabricated using outside asymmetric alumina tubes by secondary growth of ball-milled SSZ-13 seeds. The composition of membrane gel and synthesis time were modified. The Si/Al ratio in framework of the membrane was as high as 42 when SiO₂/Al₂O₃ ratio of the gel increased to 140. The effects of test parameters such as pressure drop, temperature, feed flow rate and concentration on membrane performance were investigated. The test pressure drop was up to 2 MPa. The ultra-high CO₂/H₂ selectivity of 161 with excellent CO₂ permeances of ~6.3 × 10⁻⁷ mol/(m² s Pa) (=3760 GPU) were observed for the best membrane at 243 K and pressure drop of 0.2 MPa. Carbon dioxide permeance through high-silica SSZ-13 zeolite membrane was 4.2 × 10⁻⁷ mol/(m² s Pa) (=2500 GPU) at 298 K and pressure drop of 2.0 MPa, and the CO₂/H₂ selectivity was 17.4. The current high-silica SSZ-13 zeolite membranes exceeded the upper bound of polymeric membranes and other inorganic membranes in CO₂/H₂ plots and owned great potentials for H₂ production from syngas.     

Fabrication and characterization of highly efficient three component CuBTC/graphene oxide/PSF membrane for gas separation application

Metal organic frameworks (MOFs) with marvelous properties have aroused enormous attention for different application especially gas adsorption and separation. In this regard, fabrication of MOF hybrids with carbon based materials is new strategy to upgrade MOF performance. In this study CuBTC (Copper benzene-1,3,5-tricarboxylic acid)/graphene oxide (GO) composite was synthesized and characterized by BET, SEM, TGA, XRD and FT-IR techniques. Then CuBTC and CuBTC/GO composite were incorporated into polysulfone (PSF) polymer to construct mixed matrix membranes (MMMs). The obtained membranes were characterized by SEM, TGA, XRD and tensile tests and their gas permeability was measured. The results were compared to those of CuBTC/PSF MMMs. It was revealed that CuBTC/GO composite as filler showed superior performance relative to CuBTC. For instance, 15 wt% loading of CuBTC/GO in PSF represented outstanding gas separation behavior while the same loading of CuBTC in PSF deteriorated performance of MMM. Well particle dispersion and favorable polymer-filler interaction were responsible for such observed difference. A high H₂/CH₄ and H₂/N₂ selectivity of 80.03 and 70.46 were recorded for CuBTC/GO in PSF (15 wt%) compared to 44.56 and 40.92 for CuBTC in PSF (15 wt%).     

H2 permeation and its influence on gases through a SAPO-34 zeolite membrane

This work analysed the permeation of binary and ternary H₂-containing mixtures through a SAPO-34 membrane, aiming at investigating how hydrogen influences and its permeation is influenced by the presence of the other gaseous species, such as CO₂ and CH₄. We considered the behaviour of various gas mixtures in terms of permeability and selectivity at various temperatures (25–300 °C), feed pressures (400–1000 kPa) and compositions by means of an already validated mass transport model, which is based on surface and gas translation diffusion. We found that the presence of CO₂ and CH₄ in the H₂-containing mixtures influences in a similar way the H₂ permeation, reducing its permeability of about 80% compared to the single-gas value because of their stronger adsorption. On the other hand, H₂ promotes the permeation of CO₂ and CH₄, causing an increment of their permeability with respect to those as single gases. These combined effects reflected in interesting selectivity values in binary mixture (e.g., CO₂/H₂ about 11 at 25 °C, H₂/CH₄ about 9 at 180 °C), which showed the potential of SAPO-34 membranes in treating of H₂-containing mixtures.     

Active block copolymer layer on carboxyl-functionalized PET film for hydrogen separation

To rationalize the energy requirements and environmental complications of the world, supply of pure hydrogen is the most promising as well best possible approach of such issues. Purified hydrogen gas is the necessity factor for the hydrogen-based economy. Hydrogen perm-selective membrane plays a crucial role for producing a large amount of hydrogen. Palladium is one of the best materials because of its excellent affinity to absorb hydrogen. In present work, our aim to improve selectivity as well permeability of the H₂ gas compare to N₂ and CO₂ gases of the block copolymer coated functionalized porous PET membrane. Porous polyethylene terephthalate (PET) membranes having pore size 0.2 μm, functionalized with a carboxyl group. The supramolecular assembly was prepared from PS (35500)-b- P4VP (4400) and 2-(4- Hydroxyphenylazo) benzoic acid (HABA) in 1, 4-dioxane. Chemically synthesized palladium nanoparticles were deposited on carboxylated block copolymer (BC) coated porous PET membrane. It is an appropriate way to use H₂ sensitive materials with block copolymer coated functionalized membranes to enhance the selectivity of H₂. It has been found that such membranes gain better permeability and selectivity towards H₂ as compared with N₂ and CO₂. Increment with the dipping time of these membranes in the palladium nanoparticle solution, permeability as well selectivity of H₂ over N₂, CO₂ increases as the more attachment of Palladium nanoparticles. A fine active layer of block copolymer on the carboxyl functionalized PET membrane play a crucial role for hydrogen based gas separation. The magnitude of the permeability of such membranes for different gases shows dependency on the pore size of the upper layer (BC coated) of the membrane in addition to the molecule size of the permeating gas. Block copolymer coating of the membranes established an effective responsibility for the selectivity of H₂ over CO₂ gas as well over N₂ gas.