Renewable energy systems based on hydrogen for remote applications

An integrated renewable energy (RE) system for powering remote communication stations and based on hydrogen is described. The system is based on the production of hydrogen by electrolysis whereby the electricity is generated by a 10 kW wind turbine (WT) and 1 kW photovoltaic (PV) array. When available, the excess power from the RE sources is used to produce and store hydrogen. When not enough energy is produced from the RE sources, the electricity is then regenerated from the stored hydrogen via a 5 kW proton exchange membrane fuel cell system. Overview results on the performances of the WT, PV, and fuel cells system are presented.     

An analysis of hydrogen production from renewable electricity sources

Three aspects of producing hydrogen via renewable electricity sources are analyzed to determine the potential for solar and wind hydrogen production pathways: a renewable hydrogen resource assessment, a cost analysis of hydrogen production via electrolysis, and the annual energy requirements of producing hydrogen for refueling. The results indicate that ample resources exist to produce transportation fuel from wind and solar power. However, hydrogen prices are highly dependent on electricity prices. For renewables to produce hydrogen at $2 kg⁻¹, using electrolyzers available in 2004, electricity prices would have to be less than $0.01 kWh⁻¹. Additionally, energy requirements for hydrogen refueling stations are in excess of 20 GWh/year. It may be challenging for dedicated renewable systems at the filling station to meet such requirements. Therefore, while plentiful resources exist to provide clean electricity for the production of hydrogen for transportation fuel, challenges remain to identify optimum economic and technical configurations to provide renewable energy to distributed hydrogen refueling stations.     

Dynamic production,storage, and use of renewable hydrogen: A technical-economic-environmental analysis in the public transport system in São Paulo state,Brazil

This article proposes a calculation methodology that starts from the demand calculation to supply a fleet bus with renewable hydrogen based on the electrolysis process until the energetic, economic, and environmental analyses, involving all the processes of the productive chair. Also considering the dynamic behaviour of the following hydrogen processes: production, storage, and use. The simplified scheme of the proposed system configuration to be studied consists of the use of alternative and renewable sources of energy (solar-wind-biogas) to generate electrical energy in order to produce hydrogen from electrolysis of the water, which is stored in its gaseous state and subsequently redirected to a filling station to be used as vehicle fuel in buses. The results show that to feed one bus the hybrid system generates an average of 78,110 kWh/month with an installed capacity of 1101.905 kW, producing 1209.90 kgH₂/month through the electrolysis process from water. The results also show a range of electricity generation costs between 1.130 and 0.123 US$/kWh and H₂ production between 0.963 and 0.110 US$/kWh. Concluding that the application of renewable energies to produce hydrogen and electricity for the public transport sector is an attractive alternative in the future throughout the country, because the proposed system is technically, economically and ecologically viable.     

Hydrogen generation from small-scale wind-powered electrolysis system in different power matching modes

This study presents a techno-economic evaluation on hydrogen generation from a small-scale wind-powered electrolysis system in different power matching modes. For the analysis, wind speed data, which measured as hourly time series in Kirklareli, Turkey, were used to predict the electrical energy and hydrogen produced by the wind–hydrogen energy system and their variation according to the height of the wind turbine. The system considered in this study is primarily consisted of a 6 kW wind-energy conversion system and a 2 kW PEM electrolyzer. The calculation of energy production was made by means of the levelized cost method by considering two different systems that are the grid-independent system and the grid-integrated system. Annual production of electrical energy and hydrogen was calculated as 15,148.26 kWh/year and 102.37 kg/year, respectively. The highest hydrogen production is obtained in January. The analyses showed that both electrical energy and hydrogen production depend strongly on the hub height of wind turbine in addition to the economic indicators. In the grid-integrated system, the calculated levelized cost of hydrogen changes in the range of 0.3485–4.4849 US$/kg for 36 m hub height related to the specific turbine cost. The grid-integrated system can be considered as profitable when the excess electrical energy delivered by system sold to the grid.     

Solar and wind energy in Poland as power sources for electrolysis process - A review of studies and experimental methodology

The production of hydrogen is still a major challenge, due to the high costs and often also environmental burdens it generates. It is possible to produce hydrogen in emission-free way: e.g. using a process of electrolysis powered by renewable energy. The paper presents the concept of a research, experimental stand for the storage of renewable energy in the form of hydrogen chemical energy with the measurement methodology. The research involves the use of proton exchange membrane electrolysis technology, which is characterized by high efficiency and flexibility of energy extraction for the process of electrolysis from renewable sources. The system consist of PV panel, PEM electrolyzer, battery, programmable logic controller system and optional a wind turbine. Preliminary experimental tests results have shown that the electrolyzer can produce in average 158.1 cc/min of hydrogen with the average efficiency 69.87%.     

A flexible analytical model for operational investigation of solar hydrogen plants

Hydrogen will become a dominant energy carrier in the future and the efficiency and lifetime cost of its production through water electrolysis is a major research focus. Alongside efforts to offer optimum solutions through plant design and sizing, it is also necessary to develop a flexible virtualised replica of renewable hydrogen plants, that not only models compatibility with the “plug-and-play” nature of many facilities, but that also identifies key elements for optimisation of system operation. This study presents a model for a renewable hydrogen production plant based on real-time historical and present-day datasets of PV connected to a virtualised grid-connected AC microgrid comprising different technologies of batteries, electrolysers, and fuel cells. Mathematical models for each technology were developed from chemical and physical metrics of the plant. The virtualised replica is the first step toward the implementation of a digital twin of the system, and accurate validation of the system behaviour when updated with real-time data. As a case study, a solar hydrogen pilot plant consisting of a 60 kW Solar PV, a 40 kW PEM electrolyser, a 15 kW LIB battery and a 5 kW PEM fuel cell were simulated and analysed. Two effective operational factors on the plant's performance are defined: (i) electrolyser power settings to determine appropriate hydrogen production over twilight periods and/or overnight and (ii) a user-defined minimum threshold for battery state of charge to prevent charge depletion overnight if the electrolyser load is higher than its capacity. The objective of this modelling is to maximise hydrogen yield while both loss of power supply probability (LPSP) and microgrid excess power are minimised. This analysis determined: (i) a hydrogen yield of 38–39% from solar DC energy to hydrogen energy produced, (ii) an LPSP <2.6 × 10^?4 and (iii) < 2% renewable energy lost to the grid as excess electricity for the case study.     

Cost analysis of wind-electrolyzer-fuel cell system for energy demand in Pınarbaşı-Kayseri

In this study, the hydrogen production potential and costs by using wind/electrolysis system in P?narba??-Kayseri were considered. In order to evaluate costs and quantities of produced hydrogen, for three different hub heights (50 m, 80 m and 100 m) and two different electrolyzer cases, such as one electrolyzer with rated power of 120 kW (Case-I) and three electrolyzers with rated power of 40 kW (Case-II) were investigated. Levelised cost of electricity method was used in order to determine the cost analysis of wind energy and hydrogen production. The results of calculations brought out that the electricity costs of the wind turbines and hydrogen production costs of the electrolyzers are decreased with the increase of turbine hub height. The maximum hydrogen production quantity was obtained 14192 kgH₂/year and minimum hydrogen cost was obtained 8.5 $/kgH₂ at 100 m hub height in the Case-II.     

A mobile off-grid platform powered with photovoltaic/wind/battery/fuel cell hybrid power systems

Cross utilization of photovoltaic/wind/battery/fuel cell hybrid-power-system has been demonstrated to power an off-grid mobile living space. This concept shows that different renewable energy sources can be used simultaneously to power off-grid applications together with battery and hydrogen energy storage options. Photovoltaic (PV) and wind energy are used as primary sources and a fuel cell is used as backup power. A total of 2.7 kW energy production (wind and PV panels) along with 1.2 kW fuel cell power is supported with 17.2 kWh battery and 15 kWh hydrogen storage capacities. Supply/demand scenarios are prepared based on wind and solar data for Istanbul. Primary energy sources supply load and charge batteries. When there is energy excess, it is used to electrolyse water for hydrogen production, which in turn can either be used to power fuel cells or burnt as fuel by the hydrogen cooker. Power-to-gas and gas-to-power schemes are effectively utilized and shown in this study. Power demand by the installed equipment is supplied by batteries if no renewable energy is available. If there is high demand beyond battery capacity, fuel cell supplies energy in parallel. Automatic and manual controllable hydraulic systems are designed and installed to increase the photovoltaic efficiency by vertical axis control, to lift up & down wind turbine and to prevent vibrations on vehicle. Automatic control, data acquisition, monitoring, telemetry hardware and software are established. In order to increase public awareness of renewable energy sources and its applications, system has been demonstrated in various exhibitions, conferences, energy forums, universities, governmental and nongovernmental organizations in Turkey, Austria, United Arab Emirates and Romania.     

Techno-economic analysis and optimization of a proposed solar-wind-driven multigeneration system; case study of Iran

This paper performs a thermo-economic assessment of a multi-generation system based on solar and wind renewable energy sources. This system works to generate power, freshwater, and hydrogen, which consists of the following parts: the solar collectors, Steam Rankine subsystem, Organic Rankine subsystem, desalination part, and hydrogen production and compression unit. Initially, the effects of variables including reference temperature, solar radiation intensity, wind speed, and solar cycle mass flow rate, which depend on weather conditions and affect the performance of the integrated system, were investigated. The thermodynamic analysis results showed that the overall study's exergy efficiency, the rate of hydrogen and freshwater production, and total cost rate are 33.3%, 7.92 kg/h, 1.6398 kg/s, and 61.28 $/h, respectively. Also, the net power generation rate in the Steam and Organic Rankine subsystems and wind turbines are 315 kW, 326.52 kW, and 226 kW, respectively. The main goal of this study is to minimize the total cost rate of the system and maximize the exergy efficiency and hydrogen and freshwater production rate of the total system. The results of optimization showed that the exergy efficiency value improved by 20.7%, the hydrogen production rate increased by 1%, and the total cost rate value declined by 2%. Moreover, the optimum point is similar to a region in Hormozgan province, Iran. So, this region is proposed for building the power plant.     

Life cycle assessment of the electrolytic production and utilization of low carbon hydrogen vehicle fuel

Environmental burdens associated with small scale (40 L hydrogen per minute) production of hydrogen fuel using electrolysis powered by electricity generated from stand-alone wind turbines (30 kW), stand-alone photovoltaic panels (3 kW peak) and UK grid electricity (current and future) has been undertaken. Utilization of fuel within a proton exchange membrane fuel cell passenger vehicle was included and compared to the operation of a petrol vehicle, a fuel cell vehicle fuelled with non-renewable hydrogen, and an electric (battery only) vehicle. The production of renewable hydrogen from wind energy incurs increased climate change burdens compared with extraction and processing of fossil petrol (0.09 mPt compared with 0.07 mPt). However, lower burdens for fossil fuel (1.85 mPt) and climate change (0.26 mPt) are realised by the renewable hydrogen options compared with petrol (4.44 mPt and 0.44 mPt, respectively) following utilization of the fuel due to lower emissions at end use. Utilizing a combination of renewable hydrogen fuelled vehicles and grid powered electric vehicles was considered to be a viable option for meeting UK policy ambitions.     

Development of isolated energy systems based on renewable energy sources and hydrogen storage

For the development of the energy infrastructure of remote isolated consumers, an expedient solution is the creation of a modular hybrid energy system based on renewable energy sources, which will save tens of billions of rubles a year by saving expensive diesel fuel. Taking into account the high wind energy resource in these territories, the use of wind power plants as part of that system is justified. The article discusses the methodology for substantiating the parameters and modes of operation of an autonomous wind-diesel power complex based on the territorial-power classification of power supply systems and a 4-level methodology for optimizing parameters, an example of upgrading an existing diesel power plant in the Arkhangelsk region is given. The existing diesel units with a capacity of 1300 kW were replaced by a modular wind-diesel power system with a high renewable penetration level (58%) with four wind turbines with a capacity of 200 kW and a storage system with a capacity of 65 kWh. This made it possible to achieve a diesel fuel replacement share of 232 000 L per year, which in monetary terms in 2021 prices is 25 million rubles per year. As a promising direction, a variant of the territorial development of the energy sector of the Leshukonsky district of the Arkhangelsk region based on wind energy with the possibility of producing up to 100 tons of “green” hydrogen annually is considered. Various options for reducing harmful emissions in the region were considered, the maximum use of local resources allows saving up to 22 000 tons of CO_2e per year.     

Simulation of design and operation of hydrogen energy utilization system for a zero emission building

Nearly 40% of the total greenhouse gases (GHGs) are emitted from the energy consumption in buildings in Japan, which should be reduced to address global warming. A hydrogen energy utilization system with renewable energy (RE) was designed by MATLAB/Simulink simulations for realizing a zero emission building (ZEB), comprising a hydrogen-producing electrolyzer, a hydrogen storage tank, fuel cell, and battery for short-term power storage with estimated specifications of 3.0 Nm³/h, 36 Nm³, 4.2 kW, and 10 kW/17 kWh, respectively. We identified a small low-rise building (total floor area: ∼1000 m², demand: ∼5 kW) as the planned ZEB to construct and operate a bench-scale system. A 20-kW photovoltaic (PV) system was selected as the RE source. Two hydrogen production processes (constant power of 10 kW or with excess PV power) were evaluated by simulating 48-h operations on fine and cloudy days, where the former showed higher efficiency. The results with excess power on a fine day agreed well with that of actual operation, validating our simulation models. Further, the constant case was suitable for practical application.     

Wind energy,electricity, and hydrogen in the Netherlands

The curbing of greenhouse gases (GHG) is an important issue on the international political agenda. The substitution of fossil fuels by renewable energy sources is an often-advocated mitigation strategy. Wind energy is a potential renewable energy source. However, wind energy is not reliable since its electricity production depends on variable weather conditions. High wind energy penetration rates lead to losses due to power plant operation adjustments to wind energy. This research identifies the potential energetic benefits of integrated hydrogen production in electricity systems with high wind energy penetration. This research concludes that the use of system losses for hydrogen production via electrolysis is beneficial in situations with ca. 8 GW or more wind energy capacity in the Netherlands. The 2020 Dutch policy goal of 6 GW will not benefit from hydrogen production in terms of systems efficiency. An ancillary beneficial effect of coupling hydrogen production with wind energy is to relieve the high-voltage grid.     

Sustainable energy planning based on a stand-alone hybrid renewableenergy/hydrogen power system: Application in Karpathos island, Greece

This study presents the sustainable planning of a renewables-based energy system, which aims to fulfil the electric needs of the island by replacing the existing diesel generators with new wind farms, photovoltaic installations and hydrogen production systems. Electric system design and least cost planning analysis were concluded using historic data from both demand and supply sides. An optimal “sustainable island” scheme should ensure 100% use of renewable energy resources for power generation, while hydrogen production is ideal for covering storage and transportation needs. Due to its morphology and scale, Karpathos applies perfectly for wind and solar energy systems, due to increased solar resource (about 1790 kWh/m².year of global irradiation) and high wind potential (average of 9 m/s in specific locations). Therefore, this case study examines an increase in RES penetration up to 20% in the electric energy mixture, a hydrogen production plan just for the needs of transport and a more aggressive, 100% renewables scheme that ensures a self-fulfilling energy system based on indigenous renewable resources.     

Green hydrogen as feedstock: Financial analysis of a photovoltaic-powered electrolysis plant

The weather-dependent electricity generation from Renewable Energy Sources (RES), such as solar and wind power, entails that systems for energy storage are becoming progressively more important. Among the different solutions that are being explored, hydrogen is currently considered as a key technology allowing future long-term and large-scale storage of renewable power.Today, hydrogen is mainly produced from fossil fuels, and steam methane reforming (SMR) is the most common route for producing it from natural gas. None of the conventional methods used is GHG-free. The Power-to-Gas concept, based on water electrolysis using electricity coming from renewable sources is the most environmentally clean approach. Given its multiple uses, hydrogen is sold both as a fuel, which can produce electricity through fuel cells, and as a feedstock in several industrial processes. Just the feedstock could be, in the short term, the main market of RES-based hydrogen.In this paper, we present the results obtained from a techno-economic-financial evaluation of a system to produce green hydrogen to be sold as a feedstock for industries and research centres. A system which includes a 200 kW photovoltaic plant and a 180 kW electrolyser, to be located in Messina (Italy), is proposed as a case study. According to the analyses carried out, and taking into account the current development of technologies, it has been found that investment to realise a small-scale PV-based hydrogen production plant can be remunerative.     

Value of hydro power flexibility for hydrogen production in constrained transmission grids

The cost of large scale hydrogen production from electrolysis is dominated by the cost of electricity, representing 77–89% of the total costs. The integration of low-cost renewable energy is thus essential to affordable and clean hydrogen production from electrolysis. Flexible operation of electrolysis and hydro power can facilitate integration of remote energy resources by providing the flexibility that is needed in systems with large amounts of variable renewable energy. The flexibility from hydro power is limited by the physical complexities of the river systems and ecological concerns which makes the flexibility not easily quantifiable. In this work we investigate how different levels of flexibility from hydro power affects the cost of hydrogen production.We develop a two-stage stochastic model in a rolling horizon framework that enables us to consider the uncertainty in wind power production, energy storage and the structure of the energy market when simulating power system operation. This model is used for studying hydrogen production from electrolysis in a future scenario of a remote region in Norway with large wind power potential. A constant demand of hydrogen is assumed and flexibility in the electrolysis operation is enabled by hydrogen storage. Different levels of hydro power flexibility are considered by following a reservoir guiding curve every hour, 6 h or 24 h.Results from the case study show that hydrogen can be produced at a cost of 1.89 €/kg in the future if hydro power production is flexible within a period of 24 h, fulfilling industry targets. Flexible hydrogen production also contributes to significantly reducing wasted energy from spillage from reservoirs or wind power curtailment by up to 56% for 24 h of flexibility. The results also show that less hydro power flexibility results in increased flexible operation of the electrolysis plant where it delivers 39–46% more regulating power, operates more on higher power levels and stores more hydrogen.     

The role of hydrogen in high wind energy penetration electricity systems: The Irish case

The deployment of wind energy is constrained by wind uncontrollability, which poses operational problems on the electricity supply system at high penetration levels, lessening the value of wind-generated electricity to a significant extent. This paper studies the viability of hydrogen production via electrolysis using wind power that cannot be easily accommodated on the system. The potential benefits of hydrogen and its role in enabling a large penetration of wind energy are assessed, within the context of the enormous wind energy resource in Ireland. The exploitation of this wind resource may in the future give rise to significant amounts of surplus wind electricity, which could be used to produce hydrogen, the zero-emissions fuel that many experts believe will eventually replace fossil fuels in the transport sector. In this paper the operation of a wind powered hydrogen production system is simulated and optimised. The results reveal that, even allowing for significant cost-reductions in electrolyser and associated balance-of-plant equipment, low average surplus wind electricity cost and a high hydrogen market price are also necessary to achieve the economic viability of the technology. These conditions would facilitate the installation of electrolysis units of sufficient capacity to allow an appreciable increase in installed wind power in Ireland. The simulation model was also used to determine the CO₂ abatement potential associated with the wind energy/hydrogen production.     

Hydrogen production from wind energy in Western Canada for upgrading bitumen from oil sands

Hydrogen is produced via steam methane reforming (SMR) for bitumen upgrading which results in significant greenhouse gas (GHG) emissions. Wind energy based hydrogen can reduce the GHG footprint of the bitumen upgrading industry. This paper is aimed at developing a detailed data-intensive techno-economic model for assessment of hydrogen production from wind energy via the electrolysis of water. The proposed wind/hydrogen plant is based on an expansion of an existing wind farm with unit wind turbine size of 1.8 MW and with a dual functionality of hydrogen production and electricity generation. An electrolyser size of 240 kW (50 Nm³ H₂/h) and 360 kW (90 Nm³ H₂/h) proved to be the optimal sizes for constant and variable flow rate electrolysers, respectively. The electrolyser sizes aforementioned yielded a minimum hydrogen production price at base case conditions of $10.15/kg H₂ and $7.55/kg H₂. The inclusion of a Feed-in-Tariff (FIT) of $0.13/kWh renders the production price of hydrogen equal to SMR i.e. $0.96/kg H_2, with an internal rate of return (IRR) of 24%. The minimum hydrogen delivery cost was $4.96/kg H₂ at base case conditions. The life cycle CO₂ emissions is 6.35 kg CO₂/kg H₂ including hydrogen delivery to the upgrader via compressed gas trucks.     

Investigation of green hydrogen production and development of waste heat recovery system in biogas power plant for sustainable energy applications

In this study, biogas power production and green hydrogen potential as an energy carrier are evaluated from biomass. Integrating an Organic Rankine Cycle (ORC) to benefit from the waste exhaust gases is considered. The power obtained from the ORC is used to produce hydrogen by water electrolysis, eliminate the H₂S generated during the biogas production process and store the excess electricity. Thermodynamic and thermoeconomic analyses and optimization of the designed Combined Heat and Power (CHP) system for this purpose have been performed. The proposed study contains originality about the sustainability and efficiency of renewable energy resources. System design and analysis are performed with Engineering Equation Solver (EES) and Aspen Plus software. According to the results of thermodynamic analysis, the energy and exergy efficiency of the existing power plant is 28.69% and 25.15%. The new integrated system's energy, exergy efficiencies, and power capacity are calculated as 41.55%, 36.42%, and 5792 kW. The total hydrogen production from the system is 0.12412 kg/s. According to the results of the thermoeconomic analysis, the unit cost of the electricity produced in the existing power plant is 0.04323 $/kWh. The cost of electricity and hydrogen produced in the new proposed system is determined as 0.03922 $/kWh and 0.181 $/kg H₂, respectively.     

Triple hybrid system coupling fuel cell with wind turbine and thermal solar system

One of the most challenging issues in the domain of renewable energy is the instability of produced power. To put it another way, renewable resources such as solar energy cannot provide continuous energy supply because they rely on natural phenomena that vary randomly. That said, to cover the potential lack of energy that may occur, hybrid renewable energy system can be adopted. In other terms, instead of using single renewable energy source, two different sources can be utilized in order to optimize the output power all over the year. Furthermore, complementary energy system is needed along with renewable sources, to store energy and insure the supply during shortage period. With this in mind, a Green-Green energy system can be constructed by using green storage system such as Fuel Cell to be coupled with the renewable sources. In the light of green-green energy concept, the present paper examines a triple wind-solar-fuel cell combination in the aim of overcoming the energy shortage that occurs during several months of the year. A case study on the region of Dahr Al-Baidar in Lebanon is conducted to present the advantage of the proposed system. Results show that combining wind energy system with thermal solar system allows overcoming the low power produced by solar thermal system especially in winter. For illustration 16 kW are produced by wind turbine during the month of January, by contrast the thermal solar system provides 2 kW during the same period. Nevertheless, in June thermal solar offers 17 kW and wind turbine produces 11 kW.