In this study, poly(L-lactic acid) (PLA)/low molar mass alkali lignin (aL) (1%, 5% and 10% w/w) composites were prepared primarily for a comprehensive understanding of the effect of aL on their antimicrobial properties, biocompatibility and cytotoxic behavior. The properties were evaluated by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, thermogravimetry and X-ray diffraction. The mechanical, water vapor barrier properties and photodegradability were analyzed as well. The results showed a significant inhibiting effect of aL on the crystallization behavior of PLA, increased water barrier properties (up to 73%) and photodegradability. PLA/aL composites showed a tenfold reduction in Gram-positive bacteria viability, very good cellular response and very low cytotoxicity levels, thus validating these materials as non-cytotoxic and with high potential to be used as food packaging.
Graphical abstractThe caloric effects under combined applications of magnetic field and hydrostatic pressure to a MnCoSi meta-magnet were investigated. Under a magnetic field change of 0–5 T, the maximum magnetic entropy change was enhanced by 35.7% when a 3.2kbar hydrostatic pressure was applied, and the cooling temperature span was extended by 60 K when a hydrostatic pressure of 9.7 kbar was applied. The coupled caloric entropy change, which originates from the coupling between the magnetism and volume, was calculated and accounted for the enhanced entropy change of MnCoSi. The present work facilitates the use of MnCoSi as a solid-state refrigerant and also enriches the investigation of the multicaloric effect under multiple external fields.
Graphical abstractWe review the literature describing the use of interleaves to increase interlaminar fracture toughness in fibre-reinforced polymer composites and hence to improve damage tolerance. From an analysis of data provided in the literature from the use of microfibre and nanofibre interleaves, we show that the performance of these widely researched systems is clearly differentiated when plotted against the mean coverage of the interleaf. Using a simple analysis, we suggest that this can be attributed to the influence of their porous architectures on the infusion of resin. We show also that the superior toughening performance of microfibre interleaves is only weakly influenced by the choice of fibre. We find also that the inclusion of carbon nanotubes within interleaves to deliver multifunctional composites can be optimised by using a hybrid system with microfibres.
Graphical abstractSilver nanowires find use in a myriad of applications, including communication systems, sensors, medical devices and electrical equipment. Temperature-dependent electrical and thermal properties of chemically derived silver nanowires are rarely explored. In the present work, seed-mediated synthesis of silver nanowires has been carried out, and their electrical and thermal conductivity at 300 K is found to be 1.848?×?107 S/m and 64.8 W/mK, respectively. A screen-printable ink of silver nanowires is formulated and printed on low-cost and widely used substrates like paper and cotton fabrics. Flexible printed electrodes could be made possible with uniform printed structures obtained in cotton fabric and paper substrate. The printed pattern exhibited sheet resistance of 0.7 Ω/sq. Screen-printed silver nanowires on paper show shielding efficiency of 99.9% in X band, which promotes them as excellent candidates in fabricating lightweight electronic devices by a one-step printing process.
Graphical abstractMultiphase particle-reinforced strategy shows promise for efficiently improving the comprehensive properties of aluminum matrix composites (AMCs) such as thermophysical and mechanical properties. In this work, AMC reinforced with β-eucryptite (LAS), and silicon carbide (SiC) particles were successfully prepared via a powder forging process. The microstructure morphology, interface compatibility, and coefficient of thermal expansion (CTE) of these composites were evaluated. Microstructural characterization illustrated that the co-effect of SiC and LAS resulted in a discontinuous phase with a microporous and deformation-free structure. The microporous structure of these composites was conducive for inward expansion and the elimination of internal stress, effectively limiting the outward thermal expansion behavior of the Al alloys. Moreover, SiC and LAS exhibited tight interfacial bonds with the Al grains, enhancing interfacial bonding strength. These composites provided practical and robust tensile stress that limited the thermal expansion of the Al matrix under heating. A fine Al grain size (53.5 nm) and low micro-strain (0.4?×?10–4) were obtained with increasing LAS content. Consequently, the composites achieved a low CTE of 17.27?×?10–6 K?1 at 500 °C. The experimental CTE values were also compared with theoretical values calculated by a rule of mixture model to confirm that the excellent interfacial bonding between the LAS and SiC reinforcements and the Al matrix imposed an effective constraint on matrix expansion.
Graphical abstractHybrid organic–inorganic nanocomposites are great candidates for display and illumination systems due to improved optoelectronic properties and photostability. This work endeavours towards the scientific study of the influence of defect-induced zinc oxide nanoparticles (ZnO) on the optical characteristics of poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV). ZnO nanoparticles consist of many vacancies which facilitate light emission across the visible region. The green defective emission occurring due to the presence of oxygen vacancies in ZnO was used to re-excite MEH-PPV and hence, improve the luminescence quantum efficiency. The photostability of the nanocomposite was enhanced through charge transfer (prevents the formation of superoxides) and energy transfer (reduces the non-radiative decay) mechanisms.
Graphical abstractApplication of phase change materials (PCMs)-based thermal management technology in flexible electronic devices has been inhibited due to the leakage and strong rigidity of PCMs. A novel flexible composite PCMs with ultrahigh extensibility was developed in this paper. Concretely, a kind of paraffin@copper (PA@Cu) microcapsule with paraffin as core and nano-Cu particle as “flexible” metal shell was prepared by a simple Pickering emulsion method in an aqueous medium. The encapsulation ratio of paraffin reached 98wt%. Then the PA@Cu microcapsules were introduced into uncured liquid silicone to fabricate flexible composite PCMs (PA@Cu/SE). SEM results demonstrated that the microcapsules were tightly and uniformly wrapped in the three-dimensional network structure of silicone elastomer matrix. Owing to the good compatibility of PA@Cu with the polymer elastomer and a barrier for the melted PA provided by the “flexible” nano-Cu shell, the resulting composite PCMs present superior flexibility and thermal reliability. Tensile tests showed that the flexible composites with a relative higher loading of PA@Cu (40wt%) exhibit outstandingly larger extensibility (>?730%) than many reported literatures. In addition, the composites presenting superior thermal protection for biological tissue make them well-suited for thermal management in wearable electronics.
Graphical abstractIn view of the disadvantages of concentration polarization and trade-off effects in the application of membrane in desalination field, oxide-nano graphene oxide/polyamide (O-NGO/PA) loose intermediate layer and PA ultra-thin dense layer were introduced to fabricate PA/O-NGO/polyphenylene sulfide composite membrane with sandwich structure via multi-step interfacial polymerization (MS-IP) method. The selective permeation mechanism of ultrathin layer produced by different aqueous monomers (PIP and MPD) was studied, the effect of its physicochemical structure on the relief of concentration polarization phenomenon and the breakthrough of trade-off effect was analyzed. The ultra-thin and dense PA layer mainly played the role of interception and shortened the water molecular penetration path. In the retention test of metal salt solution, compared with the rough surface, it was found that the smooth surface was more conducive to the diffusion of intercepted metal ions into the feed solution, thus alleviating the concentration polarization phenomenon.
Graphical abstractAquivion membrane displays improved properties as compared to Nafion membrane, partly due to shorter side chains. However, some improvements are still necessary for proton exchange membrane fuel cell to operate at low relative humidity. To overcome this drawback, the addition of clay nanoparticle into the Aquivion matrix can be considered. In this study, different composite membranes have been prepared mixing short-side-chain PFSA (perfluorosulfonic acid) Aquivion and selectively modified halloysite nanotubes for PEMFC low relative humidity operation. Halloysites were grafted with fluorinated groups, sulfonated groups, or perfluoro-sulfonated groups on inner or outer surface of the tubes. The obtained composite membranes showed improved properties, especially higher water uptake associated with reduced swelling and better mechanical strength compared to pristine Aquivion membrane and commercially available Nafion HP used as reference. The best performance in this study was obtained with Aquivion loaded with 5 wt% of pretreated perfluoro-sulfonated halloysite. The composite membrane, referred to as Aq/pHNT-SF5, displayed the largest water uptake and proton conductivity among the panel of membranes tested. The chemical stability was not affected by the presence of halloysite in the Aquivion matrix.
Graphical abstractNon-dendritic microstructures are generally obtained in metals after semi-solid deformation (deformation during solidification); however, dendritic growth is preferred without deformation. The fragmentation of dendrites is recognized as an essential contributing factor to non-dendritic microstructures. However, the underlying mechanism of fragmentation needs to be clarified in depth. It is infamously hard for researchers to carry out a direct observation of this process. Moreover, a comprehensive numerical survey of this process is not trivial. The present research reported a new method to model dendritic growth during semi-solid deformation. The motion and deformation of the solid coupled with liquid flow in the melt were treated as the two-phase flow because plastic materials could be formulated as non-Newtonian fluids. The vector-valued phase-field formulation and the self-constructed Navier–Stokes solver made it possible to simulate the growth, motion, deformation, fragmentation and agglomeration of two dendrites coupled with liquid flow in the melt. Computational results suggest that fragmentation can occur when the grain boundary is wet and penetrated by the melt, giving new supporting evidence to a previously proposed mechanism for the fragmentation of dendrites.
Graphical abstractThe development of eco-friendly connection material instead of steel is a challenging problem in timber structures. Following densification, the mechanical properties of low-density species can be significantly improved. Densified wood may be a potential connection material in timber structures. This paper reviewed the different processing for densified wood, and obtained favorable mechanical properties and dimensional stability based on small specimen sizes, which are much less than the applicable sizes in practice. A densification processing with alkali pretreatment was adopted for poplar widely cultivated in the world to produce the densified poplar, which has been rarely reported as connection material. Various specimens of densified poplar were tested to obtain their main mechanical properties such as strength and deformability. The set recovery of densified poplar was also measured to observe their dimensional stability. In addition, the hygroscopic swelling strains for the diameter of densified poplar dowel were measured to present their moisture-dependent behavior. The improved mechanical properties and dimensional stability confirmed the fact that densified poplar with alkali pretreatment can be an optimal connection material.
Graphical abstractIn this critical note, the thermal stability behavior of ultra-fine grained (UFG) and nano-structured (NS) metals and alloys produced through severe plastic deformation (SPD) techniques is reviewed. For this case, the common engineering metals with body-centered cubic (BCC), face-centered cubic (FCC), and hexagonal close-packed (HCP) crystal structures such as aluminum, copper, nickel, magnesium, steel, titanium, and their relating alloys were assessed. Microstructural evolution in these severely deformed materials following post-processing annealing treatment was investigated for various times and temperatures below the recrystallization point. The microstructure development reported in the literature was studied in terms of the stable grain structures correlated with different levels of plastic straining. The stacking fault energy (SFE) is noted to be a key issue which has a critical influence in predicting the coalescence or coarsening behavior of ultra-fine and nanoscale grains after SPD treatment by controlling the cross-slip phenomenon for screw dislocations.
Graphical AbstractThe kinetics of electrochemical corrosion of aluminum alloy (AlMg6) surfaces with different wettability was analyzed. The surfaces were processed by three different methods, in particular, polishing, laser texturing, the combination of laser texturing and low-temperature heating. After laser processing, the dimple-like texture was formed on the surface, and the wettability significantly enhanced. Low-temperature heating of laser-textured AlMg6 alloy surfaces led to the wettability inversion from strongly hydrophilicity to superhydrophobicity. Microscopic and profilometric methods were used to estimate the surface degradation due to corrosion when aggressive solution droplets (a mixture of NaCl and hydrogen peroxide aqueous solutions) evaporated. The potentiodynamic polarization measurements of AlMg6 alloy surfaces were conducted. The typical modes of corrosion and evaporation of aggressive solution droplets were detected. The kinetics of corrosion was estimated by the behavior of the corrosion area evolution. In addition, when immersing laser-textured sample with strongly hydrophilic properties into aggressive solution, the higher corrosion rate was found in the liquid meniscus region (aggressive mixture / alloy / air interface) compared to the textured site immersed in the mixture. This was explained by convection increasing the rate of reaction products removal and promoting a stronger deviation from the equilibrium state in the aggressive mixture. Experimental results of the potentiodynamic polarization measurements revealed that laser-textured samples exhibit enhanced corrosion protective properties compared to polished samples.
Graphical abstractIn this work, we systematically investigated the effects of single-step and two-step sintering methods on the structural, dielectric and energy storage properties of pure AgNbO3 lead-free antiferroelectric ceramics. Compared with the single-step sintered ceramic, the ceramic prepared by two-step sintering method has smaller grain size, dense and homogeneous microstructure. In addition, the results of dielectric temperature spectra reveal that the two-step sintering method hardly changes the phase transition temperature of AgNbO3 ceramics but greatly decreases the dielectric loss value. Most importantly, the ceramic prepared by the two-step sintering method displays high breakdown electric field strength (22 kV/mm), larger recoverable energy storage density-Wrec (2.59 J/cm3) and higher energy storage efficiency-η (45%) as well as excellent temperature stability than those of the ceramic by single-step sintering method. Furthermore, it also exhibited high power density (PD?=?25.7 MW/cm3) and extremely fast charge–discharge speed (25 ns). Our results provide a simple and novel way to design high-performance AgNbO3-based energy storage lead-free ceramics.
Graphical abstractSilica aerogel composites reinforced with different aramid fibres have been synthesized and compared considering their potential use in thermal protection systems of Space devices. These composites were prepared from tetraethoxysilane and vinyltrimethoxysilane and the network was strengthened with aramid fibres. The results showed that the physical and chemical properties of the fibres were relevant, leading to composites with different properties/performance. In general, the obtained values for bulk density were low, down to 150 kg m?3. Very good thermal properties were achieved, reaching thermal conductivities bellow 30 mW m?1 K?1, and thermal stability up to 550 °C in all cases. Short length fibres produce stiffer composites with lower thermal conductivities, while among longer fibres, meta-aramid-containing fibres lead to nanocomposites with best insulation performance. Standard tests for Space materials qualification, as thermal cycling and outgassing, were conducted to assess the compliance with Space conditions, confirming the suitability of these aerogel composites for this application.
Graphical abstractThe properties of nanoparticle–polymer composites strongly depend on the network structure of the polymer matrix. By introducing nanoparticles into a monomer (solution) and subsequently polymerizing it, the formation of the polymer phase influences the mechanical and physicochemical properties of the composite. In this study, semi-conducting indium tin oxide (ITO) nanoparticles were prepared to form a rigid nanoparticle scaffold in which 1,6-hexanediol diacrylate (HDDA), together with an initiator for photo-polymerization, was infiltrated and subsequently polymerized by UV light. During this process, the polymerization reaction was characterized using rapid scan Kubelka–Munk FT-IR spectroscopy and compared to bulk HDDA. The conductivity change of the ITO nanoparticles was monitored and correlated with the polymerization process. It was revealed that the reaction rates of the radical initiation and chain propagation are reduced when cured inside the voids of the nanoparticle scaffold. The degree of conversion is lower for HDDA infiltrated into the mesoporous ITO nanoparticle scaffold compared to purely bulk-polymerized HDDA.
Graphical abstractExtension of corrosion inhibitors from traditional molecular-scale to nanoscale will not only be significant to develop green and efficient inhibitors, but also supplement the discipline system of corrosion inhibitors. However, many research on the interfacial behavior of nano-inhibitors have ignored the special colloidal properties of nanoparticles and show no obvious differences with traditional inhibitors. In this study, graphene oxide (GO) was functionalized with polydopamine (PDA) via covalent modifications and self-polymerization, and GO-PDA was studied as a corrosion inhibitor of carbon steel in HCl solution. Diversified measurements confirmed that GO-PDA can effectively protect carbon steel from corrosion, and the inhibition efficiency almost reached 90% at 100 mg/L. Interfering factors including immersion time and concentration were investigated. The lamellar nanoparticles adsorbed on the surface of carbon steel have formed a hydrophobic film in micro-nano structures. The transition from a negative charge on the GO surface to a positively charged GO-PDA contributed to adsorption at the interface. An initial model of nano-inhibitor was established to explicate the inhibition mechanism.
Graphical abstractPlanar perovskite solar cells (PSCs) have excellent photoelectric properties and show great commercialization potential. However, there are a lot of crystal defects in the perovskite films prepared by solution method, which reduces the development process of solar cells. In this work, alizarin red s (ARS) was doped into MAPbI3 films to passivate the defect. It was shown that the addition of ARS increased the quality of perovskite film and doped perovskite film exhibited improved light absorption. In addition, it was found that there was a strong interaction between ARS and perovskite, which reduced the density of defect states. The results showed that the passivated perovskite device had improved PL intensity, increased carrier lifetimes and reduced charge recombination. After passivation, the device obtained a higher open-circuit voltage (VOC) of 1.103 V where the control device was 1.055 V, and the best power conversion efficiency (PCE) of the doped device was 18.82%, which is 11.36% higher than that of the control device of 16.90%.
Graphical abstractOxygen-containing carbon materials have been studied extensively because of their excellent dispersibility, absorptivity, separability, and supportability of catalysts. However, structural control by existing top-down methods is almost impossible. Our group has demonstrated that phloroglucinol (PG, 1,3,5-trihydroxybenzene) can be a promising raw material to synthesize structurally controlled oxygen-containing carbon materials. In this study, in addition to PG, hexahydroxybenzene (HHB), which has more oxygen and high symmetry, was used as the raw material, and a Lewis acid catalyst, tris (pentafluorophenyl) borane (TPB), was used to enhance the structural control rate and the removability of catalysts from the carbonized samples. The solubility of heat-treated HHB was lower than that of heat-treated PG, but the oxygen content of heat-treated HHB was higher than that of heat-treated PG even at 673 K. By adding TPB to PG, dibenzofuran-like structures formed, and the structural control rate increased up to 93.6%. Besides, the content of fluorine in the catalyst was reduced to 0%, indicating that TPB can be a promising recyclable catalyst to promote the structural control rate of carbonized PG.
Graphical abstractThree-dimensional (3-D) printing, also known as additive manufacturing, refers to a method used to generate a physical object by joining materials in a layer-by-layer process from a three-dimensional virtual model. 3-D printing technology has been traditionally employed in rapid prototyping, engineering, and industrial design. More recently, new applications continue to emerge; this is because of its exceptional advantage and flexibility over the traditional manufacturing process. Unlike other conventional manufacturing methods, which are fundamentally subtractive, 3-D printing is additive and, therefore, produces less waste. This review comprehensively summarises the application of additive manufacturing technologies in chemistry, chemical synthesis, and catalysis with particular attention to the production of general laboratory hardware, analytical facilities, reaction devices, and catalytically active substances. It also focuses on new and upcoming applications such as digital chemical synthesis, automation, and robotics in a synthetic environment. While discussing the contribution of this research area in the last decade, the current, future, and economic opportunities of additive manufacturing in chemical research and material development were fully covered.
Graphical abstract