Silver nanowires find use in a myriad of applications, including communication systems, sensors, medical devices and electrical equipment. Temperature-dependent electrical and thermal properties of chemically derived silver nanowires are rarely explored. In the present work, seed-mediated synthesis of silver nanowires has been carried out, and their electrical and thermal conductivity at 300 K is found to be 1.848?×?107 S/m and 64.8 W/mK, respectively. A screen-printable ink of silver nanowires is formulated and printed on low-cost and widely used substrates like paper and cotton fabrics. Flexible printed electrodes could be made possible with uniform printed structures obtained in cotton fabric and paper substrate. The printed pattern exhibited sheet resistance of 0.7 Ω/sq. Screen-printed silver nanowires on paper show shielding efficiency of 99.9% in X band, which promotes them as excellent candidates in fabricating lightweight electronic devices by a one-step printing process.
Graphical abstractThe effect of post-weld solution along with different double aging treatments on precipitation of various strengthening phases in Alloy 718 weld is carried out in the current assessment. The formation of intermetallic phases in the weld zone deteriorates the mechanical properties and quality of the weld joint. The high-temperature solution treatment at 1165 °C/1 h has dissolved the intermetallic phases and makes a suitable quantity of alloying elements accessible for precipitation of the strengthening phases. To analyze the impact of aging temperature and holding time on δ, γ' and γ" phase precipitation, four different heat treatment paths are designed. The heat treatment holding time is reduced by 53% on the welded component by applying a higher aging temperature compared to the conventional standard aging temperatures. The variation in aging temperature and holding time followed by solution treatment changes the platelet morphology of the δ phase to needle shape in the grain boundary. Significant enhancement in the tensile strength (21%) and weld hardness (121%) is witnessed due to duplex aging treatment compared to as-welded condition. The XRD analysis confirms the precipitation of γ' and γ'' strengthening phases inside the grain and δ particles in the grain boundaries.
Graphical abstractThe caloric effects under combined applications of magnetic field and hydrostatic pressure to a MnCoSi meta-magnet were investigated. Under a magnetic field change of 0–5 T, the maximum magnetic entropy change was enhanced by 35.7% when a 3.2kbar hydrostatic pressure was applied, and the cooling temperature span was extended by 60 K when a hydrostatic pressure of 9.7 kbar was applied. The coupled caloric entropy change, which originates from the coupling between the magnetism and volume, was calculated and accounted for the enhanced entropy change of MnCoSi. The present work facilitates the use of MnCoSi as a solid-state refrigerant and also enriches the investigation of the multicaloric effect under multiple external fields.
Graphical abstractOrganic/inorganic thermoelectric composites have played an important role in the development of new, green, and renewable energy sources with potential applications in efficient thermal management, flexible electronics, and bioelectronics. Electrochemical syntheses, including electropolymerization, electrochemical deposition, electrochemical doping, electrochemical post-processing, etc., require no addition of surfactants or oxidants, the products of which are easy to separate and purify, providing clean, efficient, and facile routes for the preparation of organic thermoelectric materials and their composites. In this review, the preparation, properties, and applications of organic/inorganic thermoelectric composites from electrochemical synthesis were reviewed in detail, offering a perspective on the recent advances in the field.
Graphical abstractIn view of the disadvantages of concentration polarization and trade-off effects in the application of membrane in desalination field, oxide-nano graphene oxide/polyamide (O-NGO/PA) loose intermediate layer and PA ultra-thin dense layer were introduced to fabricate PA/O-NGO/polyphenylene sulfide composite membrane with sandwich structure via multi-step interfacial polymerization (MS-IP) method. The selective permeation mechanism of ultrathin layer produced by different aqueous monomers (PIP and MPD) was studied, the effect of its physicochemical structure on the relief of concentration polarization phenomenon and the breakthrough of trade-off effect was analyzed. The ultra-thin and dense PA layer mainly played the role of interception and shortened the water molecular penetration path. In the retention test of metal salt solution, compared with the rough surface, it was found that the smooth surface was more conducive to the diffusion of intercepted metal ions into the feed solution, thus alleviating the concentration polarization phenomenon.
Graphical abstractIn this study, poly(L-lactic acid) (PLA)/low molar mass alkali lignin (aL) (1%, 5% and 10% w/w) composites were prepared primarily for a comprehensive understanding of the effect of aL on their antimicrobial properties, biocompatibility and cytotoxic behavior. The properties were evaluated by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, thermogravimetry and X-ray diffraction. The mechanical, water vapor barrier properties and photodegradability were analyzed as well. The results showed a significant inhibiting effect of aL on the crystallization behavior of PLA, increased water barrier properties (up to 73%) and photodegradability. PLA/aL composites showed a tenfold reduction in Gram-positive bacteria viability, very good cellular response and very low cytotoxicity levels, thus validating these materials as non-cytotoxic and with high potential to be used as food packaging.
Graphical abstractIn this critical note, the thermal stability behavior of ultra-fine grained (UFG) and nano-structured (NS) metals and alloys produced through severe plastic deformation (SPD) techniques is reviewed. For this case, the common engineering metals with body-centered cubic (BCC), face-centered cubic (FCC), and hexagonal close-packed (HCP) crystal structures such as aluminum, copper, nickel, magnesium, steel, titanium, and their relating alloys were assessed. Microstructural evolution in these severely deformed materials following post-processing annealing treatment was investigated for various times and temperatures below the recrystallization point. The microstructure development reported in the literature was studied in terms of the stable grain structures correlated with different levels of plastic straining. The stacking fault energy (SFE) is noted to be a key issue which has a critical influence in predicting the coalescence or coarsening behavior of ultra-fine and nanoscale grains after SPD treatment by controlling the cross-slip phenomenon for screw dislocations.
Graphical AbstractWO3, a visible light reaction catalyst, absorbs light at a wavelength of 470 nm and has many advantages, such as strong stability, long life, non-toxicity, low cost, and suitable band edges. In this review, the photocatalytic mechanism of WO3 in water pollution treatment is introduced, as well as a systematic summary, and some main strategies for improving the photocatalytic activity of WO3 in water pollution treatment are introduced, for example surface and morphology control, synthetic heterojunctions, and doping element. Finally, the main conclusions and prospects of WO3-based photocatalysts are pointed out. It can be expected that this review can provide guidance for designing low-cost, high-efficiency new WO3-based photocatalysts in the process of water pollution treatment and can meet the application prospects of efficient utilization of solar degradation in the field of environmental purification.
Graphical abstractAquivion membrane displays improved properties as compared to Nafion membrane, partly due to shorter side chains. However, some improvements are still necessary for proton exchange membrane fuel cell to operate at low relative humidity. To overcome this drawback, the addition of clay nanoparticle into the Aquivion matrix can be considered. In this study, different composite membranes have been prepared mixing short-side-chain PFSA (perfluorosulfonic acid) Aquivion and selectively modified halloysite nanotubes for PEMFC low relative humidity operation. Halloysites were grafted with fluorinated groups, sulfonated groups, or perfluoro-sulfonated groups on inner or outer surface of the tubes. The obtained composite membranes showed improved properties, especially higher water uptake associated with reduced swelling and better mechanical strength compared to pristine Aquivion membrane and commercially available Nafion HP used as reference. The best performance in this study was obtained with Aquivion loaded with 5 wt% of pretreated perfluoro-sulfonated halloysite. The composite membrane, referred to as Aq/pHNT-SF5, displayed the largest water uptake and proton conductivity among the panel of membranes tested. The chemical stability was not affected by the presence of halloysite in the Aquivion matrix.
Graphical abstractNon-dendritic microstructures are generally obtained in metals after semi-solid deformation (deformation during solidification); however, dendritic growth is preferred without deformation. The fragmentation of dendrites is recognized as an essential contributing factor to non-dendritic microstructures. However, the underlying mechanism of fragmentation needs to be clarified in depth. It is infamously hard for researchers to carry out a direct observation of this process. Moreover, a comprehensive numerical survey of this process is not trivial. The present research reported a new method to model dendritic growth during semi-solid deformation. The motion and deformation of the solid coupled with liquid flow in the melt were treated as the two-phase flow because plastic materials could be formulated as non-Newtonian fluids. The vector-valued phase-field formulation and the self-constructed Navier–Stokes solver made it possible to simulate the growth, motion, deformation, fragmentation and agglomeration of two dendrites coupled with liquid flow in the melt. Computational results suggest that fragmentation can occur when the grain boundary is wet and penetrated by the melt, giving new supporting evidence to a previously proposed mechanism for the fragmentation of dendrites.
Graphical abstractNanotechnologies known as a developing applied science have significant global socioeconomic values and many advantages obtained from nanoscale materials. Its applications can have significant effects on the performance of organizations. The advance of two-dimensional (2D) MXene-derived QDs (MQDs) is currently in the initial stages. Scholars have shown distinguished optical, electronic, thermal and mechanical attributes by surface chemistry and versatile transition metal. In this field of study, many applications are introduced like energy electromagnetic interference shielding, storage, sensors, transparent electrodes, photothermal therapy, catalysis and so on. The vast range of optical absorption attributes of MQDs along with high electronic conductivity has been detected to be key attributes because of their achievement in the mentioned usages. Currently, relatively little materials are highly known because of their basic electronic and optical properties, which can limit their full potentials. From a theoretical and experimental point of view, in this work, electronic and optical properties of MQDs along with applications corresponding to those properties were evaluated.
Graphical abstractThe development of eco-friendly connection material instead of steel is a challenging problem in timber structures. Following densification, the mechanical properties of low-density species can be significantly improved. Densified wood may be a potential connection material in timber structures. This paper reviewed the different processing for densified wood, and obtained favorable mechanical properties and dimensional stability based on small specimen sizes, which are much less than the applicable sizes in practice. A densification processing with alkali pretreatment was adopted for poplar widely cultivated in the world to produce the densified poplar, which has been rarely reported as connection material. Various specimens of densified poplar were tested to obtain their main mechanical properties such as strength and deformability. The set recovery of densified poplar was also measured to observe their dimensional stability. In addition, the hygroscopic swelling strains for the diameter of densified poplar dowel were measured to present their moisture-dependent behavior. The improved mechanical properties and dimensional stability confirmed the fact that densified poplar with alkali pretreatment can be an optimal connection material.
Graphical abstractHere, we report a multiferroic relaxor material 0.41Bi(Ni1/2Zr1/2)O3–0.59PbTiO3, which exhibits a large piezoelectric coefficient (d33, 391 pC/N), high remnant polarization (Pr, 52.3 μC/cm2) and a high electrical freezing temperature (Tf, 498 K). The electric-field-induced transition from a cubic-like phase to a tetragonal phase was confirmed by the XRD patterns and first-cycle bipolar electrostrain loop. The magnetization and magnetic field relationship changes from nonlinear to linear when cooled from 300 to 2 K. The unusual trend in magnetic behavior could be interpreted as the transitions between the super short-range orderings. Furthermore, the maximum value of magnetization shows a 14% decrease at 300 K after electrical poling.
Graphical abstractFumed silica nanoparticles (FSN) are one of the most common synthetic forms of silica, but prolonged exposure leads to cell toxicity and apoptosis due to reactive oxygen species (ROS) generation and cell membrane perturbation resulting from hydrogen bonding and electrostatic interactions. Increasing attention is being put on synthesizing FSN material that is safer both for workers involved in large-scale industrial production, and consumers coming in contact with FSN additives. In the present work, we explore the molecular structural differences and efficacy of Al- and Ti-metal-doped FSN which has previously been shown to reduce toxicity effects of FSN. We use a combination of 29Si and 27Al solid-state magic angle spinning (MAS) NMR, Raman spectroscopy, and thermogravimetric analysis (TGA) to probe the surface and bulk structure and quantify the adsorption capacity and reactivity of the metal-doped FSN with respect to amino acid thermal condensation. Alanine was selected as the amino acid of choice for its simplicity and ubiquity in biochemical reactions. The results indicate that metal doping has a modest impact on the fumed silica molecular structure with a small decrease in amino acid adsorption capacity and thermal condensation reactivity as a function of increased metal doping.
Graphical AbstractA novel bilirubin adsorbent with high hydrophilicity was facilely synthesized via one-step hydrothermal carbonization reaction by using glucose and [3-(methacryloylamino)propyl]trimethylammonium chloride (MAPTAC) as precursors, in which sustainable carbohydrate could be converted into functionalized carbonaceous materials enriched with quaternary ammonium groups using an environmentally mild process. The properties of synthesized adsorbents were characterized by helium ion microscopy, static water contact angle measurement, FT-IR, elemental analysis and nitrogen adsorption/desorption measurement. The contact angle results indicated that these materials possessed very good hydrophilicity along with the lowest contact angle at 16.2°. Moreover, the hydrophilic adsorbent prepared by only one-step demonstrated good adsorption capacity toward bilirubin (141 mg/g) than commercialized activated carbon (70 mg/g) and low non-specific adsorption toward albumin (0.21%), which had great potential to be used in hemoperfusion. In addition, kinetic adsorption behaviors were conducted using pseudo-first-order and pseudo-second-order models. The regression results showed that the kinetic adsorption data were more accurately represented by pseudo-second-order model. The equilibrium adsorption data were analyzed using two widely applied isotherm models: Langmuir and Freundlich. The results revealed that Langmuir isotherm matched the experimental results well.
Graphical AbstractThe development of hydrogen production via environment-friendly and efficient electrochemical water splitting technology leans heavily on the exploitation of highly active and durable oxygen evolution reaction (OER) electrocatalysts. Herein, nanocoral-like cerium-activated cobalt selenide (Ce-CoSe2) nanocomposites to enhance the OER catalytic activity have been successfully prepared by one-pot hydrothermal route via simply altering the cerium content. Owing to the ingenious introduction of cerium, as-prepared Ce-CoSe2 electrode displays remarkable OER performance in comparison with CoSe2. The nanocoral-like Ce-CoSe2 catalyst prepared under optimal condition just needs low overpotential of 276 and 398 mV at 10 and 50 mA cm?2, respectively. Additionally, it attains the current density of 255 mA cm?2 at the potential of 2.0 V vs. RHE, and shows long-term stability during OER. This work offers a simple and feasible pathway for the design and construct of metal dichalcogenides for green and renewable hydrogen production by electrocatalytic water splitting.
Graphical abstractThe electrical conductivity and piezoresistivity of multiwall carbon nanotube (MWCNT)/polypropylene (PP) composites obtained by extrusion are investigated, with particular attention to the possible directional effects generated during the extrusion process. This is accomplished by investigating the electrical and electromechanical responses of the nanocomposites at three MWCNT weight concentrations (3, 4 and 5 wt%) in three directions, viz. the extrusion direction, transverse to extrusion (in-plane) and through thickness. Higher electrical conductivity in the extrusion direction was more evident for the lowest MWCNT content. However, the piezoresistive sensitivity was similar in all directions. Films with 4 wt% showed the highest piezoresistive sensitivity, reaching gage factors of?~?4.5 for strains between 0 and 0.8%, and?~?10.2 for strains between 1 and 3%. After an initial drop in the electrical resistance, concomitant with stress relaxation, the changes in electrical resistance showed large reproducibility. Digital image correlation conducted during cyclic piezoresistive testing at 0.8% strain indicates small accumulation of local plasticity as the number of cycles increases, especially in zones near the electrodes. These irreversible changes in the material are expected to trigger the permanent changes in the electrical resistance measured.
Graphical abstractPlanar perovskite solar cells (PSCs) have excellent photoelectric properties and show great commercialization potential. However, there are a lot of crystal defects in the perovskite films prepared by solution method, which reduces the development process of solar cells. In this work, alizarin red s (ARS) was doped into MAPbI3 films to passivate the defect. It was shown that the addition of ARS increased the quality of perovskite film and doped perovskite film exhibited improved light absorption. In addition, it was found that there was a strong interaction between ARS and perovskite, which reduced the density of defect states. The results showed that the passivated perovskite device had improved PL intensity, increased carrier lifetimes and reduced charge recombination. After passivation, the device obtained a higher open-circuit voltage (VOC) of 1.103 V where the control device was 1.055 V, and the best power conversion efficiency (PCE) of the doped device was 18.82%, which is 11.36% higher than that of the control device of 16.90%.
Graphical abstractOxygen-containing carbon materials have been studied extensively because of their excellent dispersibility, absorptivity, separability, and supportability of catalysts. However, structural control by existing top-down methods is almost impossible. Our group has demonstrated that phloroglucinol (PG, 1,3,5-trihydroxybenzene) can be a promising raw material to synthesize structurally controlled oxygen-containing carbon materials. In this study, in addition to PG, hexahydroxybenzene (HHB), which has more oxygen and high symmetry, was used as the raw material, and a Lewis acid catalyst, tris (pentafluorophenyl) borane (TPB), was used to enhance the structural control rate and the removability of catalysts from the carbonized samples. The solubility of heat-treated HHB was lower than that of heat-treated PG, but the oxygen content of heat-treated HHB was higher than that of heat-treated PG even at 673 K. By adding TPB to PG, dibenzofuran-like structures formed, and the structural control rate increased up to 93.6%. Besides, the content of fluorine in the catalyst was reduced to 0%, indicating that TPB can be a promising recyclable catalyst to promote the structural control rate of carbonized PG.
Graphical abstractRescuing the compromised function of periodontal ligament stem cells (PDLSCs) due to hyperglycemia-induced oxidative stress and reducing the risk of postoperative infection around the interface of scaffold materials are of prime importance for periodontal regeneration in diabetes mellitus. To this end, a facile and green approach for the establishment of surfaces with antioxidative and antibacterial properties was developed in this work. Briefly, the surfaces of polystyrene (PS) plate were pre-modified with polydopamine and then coated with a genipin crosslinked layer-by-layer (LbL) assembly, which was established by using the antibacterial polyelectrolytes carboxymethyl chitosan (CMC) and polylysine (PLL) as building block. Metformin as an antioxidative agent was incorporated into the discrete nanolayers to achieve sustainable release. Our research showed that metformin-loaded LbL assembly presented favorable cytocompatibility. The released metformin could partially rescue the impaired osteogenic function of human PDLSCs induced by high glucose in vitro. Meanwhile, owing to the antibacterial activity of CMC and PLL, the colonization of common pathogenic bacteria related to periodontal disease could be disturbed on the surface of developed coatings. Accordingly, the presented strategy for surface functionalization of materials in our study holds a promising potential for periodontal regeneration application in diabetic patients.
Graphical abstract