Thermodynamic evaluation of hydrazine assisted glycerol reforming for syngas production and coke inhibition

Thermodynamic investigation of glycerol reforming has been performed to study hydrogen production, carbon dioxide evolution and coke formation. Gibb's free energy direct minimization procedure was used to calculate the concentration of different components at equilibrium. The analysis was performed at temperatures from 300K to 1000K under unit atmospheric pressure. A comparative study on steam reforming of glycerol (SRG) and glycerol reforming reaction with hydrazine has been conducted in the presence of hydrazine that act as a suitable reducing agent. Incorporation of hydrazine into glycerol reforming system helped in minimizing coke formation, maximizing hydrogen and syn-gas production. A complete conversion of glycerol with coke free products, along with reduced level of carbon dioxide and maximum hydrogen generation was obtained when glycerol steam reforming process (S/G = 1) was combined with higher moles of hydrazine. Reformation at higher temperatures could enhance the hydrogen production and decrease carbon generation due to methanation reaction and hence optimum results were accomplished at 1000K and atmospheric pressure.     

Hydrogen production by glycerol steam reforming with in situ hydrogen separation: A thermodynamic investigation

Thermodynamic features of hydrogen production by glycerol steam reforming with in situ hydrogen extraction have been studied with the method of Gibbs free energy minimization. The effects of pressure (1–5 atm), temperature (600–1000 K), water to glycerol ratio (WGR, 3–12) and fraction of H₂ removal (f, 0–1) on the reforming reactions and carbon formation were investigated. The results suggest separation of hydrogen in situ can substantially enhance hydrogen production from glycerol steam reforming, as 7 mol (stoichiometric value) of hydrogen can be obtained even at 600 K due to the hydrogen extraction. It is demonstrated that atmospheric pressure and a WGR of 9 are suitable for hydrogen production and the optimum temperature for glycerol steam reforming with in situ hydrogen removal is between 825 and 875 K, 100 K lower than that achieved typically without hydrogen separation. Furthermore, the detrimental influence of increasing pressure in terms of hydrogen production becomes marginal above 800 K with a high fraction of H₂ removal (i.e., f = 0.99). High temperature and WGR are favorable to inhibit carbon production.     

Optimization of two bio-oil steam reforming processes for hydrogen production based on thermodynamic analysis

Thermodynamics of hydrogen production from conventional steam reforming (C-SR) and sorption-enhanced steam reforming (SE-SR) of bio-oil was performed under different conditions including reforming temperature, S/C ratio (the mole ratio of steam to carbon in the bio-oil), operating pressure and CaO/C ratio (the mole ratio of CaO to carbon in the bio-oil). Increasing temperature and S/C ratio, and decreasing the operating pressure were favorable to improve the hydrogen yield. Compared to C-SR, SE-SR had the significant advantage of higher hydrogen yield at lower desirable temperature, and showed a significant suppression for carbon formation. However excess CaO (CaO/C > 1) almost had no additional contribution to hydrogen production. Aimed to achieve the maximum utilization of bio-oil with as little energy consumption as possible, the influences of temperature and S/C ratio on the reforming performance (energy requirements and bio-oil consumption per unit volume of hydrogen produced, Q_D/H2 (kJ/Nm³) and Y_Bio-oil/H2 (kg/Nm³)) were comprehensively evaluated using matrix analysis while ensuring the highest hydrogen yield as possible. The optimal operating parameters were confirmed at 650 °C, S/C = 2 for C-SR; and 550 °C, S/C = 2 for SE-SR. Under their respective optimal conditions, the Y_Bio-oil/H2 of SE-SR is significant decreased, by 18.50% compared to that of C-SR, although the Q_D/H2 was slightly increased, just by 7.55%.     

Reforming of vegetable oil for production of hydrogen: A thermodynamic analysis

The vegetable oils are one of the promising renewable feedstock for production of hydrogen suitable for application in hydrogen based fuel cells for electrical power generation. In the present work, a thermodynamic equilibrium analysis of steam reforming (SR) and autothermal steam reforming (ATSR) of vegetable oils to synthesis gas was investigated by Gibbs free energy minimization method. The thermodynamic equilibrium analysis was performed considering the vegetable oils as a mixture of triglycerides containing three same fatty acid groups in the structure. The property method used for equilibrium analysis was first regressed using available physical and chemical properties of the considered triglycerides. The regressed property method was then used to calculate the equilibrium products composition. The effects of various parameters of SR of vegetable oils, temperature and steam-to-carbon ratio (SCR), on hydrogen yield and selectivity of CO and methane was studied in a broad range of temperature (573-1273 K) and SCRs (1-6). The optimum conditions for SR of vegetable oils were then determined for maximum hydrogen yield with very low selectivity of methane. The thermodynamic equilibrium analysis of ATSR of vegetable oils was then performed at different oxygen-to-carbon ratios and thermoneutral conditions were then determined for various operating conditions.     

Hydrogen production by sorption enhanced steam reforming of propane: A thermodynamic investigation

Thermodynamic features of hydrogen production by sorption enhanced steam reforming (SESR) of propane have been studied with the method of Gibbs free energy minimization and contrasted with propane steam reforming (SR). The effects of pressure (1-5 atm), temperature (700-1100 K) and water to propane ratio (WPR, 1-18) on equilibrium compositions and carbon formation are investigated. The results suggest that atmospheric pressure and a WPR of 12 are suitable for hydrogen production from both SR and SESR of propane. High WPR is favourable to inhibit carbon formation. The minimum WPR required to eliminate carbon production is 6 in both SR and SESR. The most favourable temperature for propane SR is approximately 950 K at which 1 mol of propane has the capacity to produce 9.1 mol of hydrogen. The optimum temperature for SESR is approximately 825 K, which is over 100 K lower than that for SR. Other key benefits include enhanced hydrogen production of nearly 10 mol (stoichiometric value) of hydrogen per mole of propane at 700 K, increased hydrogen purity (99% compared with 74% in SR) and no CO₂ or CO production with the only impurity being CH₄, all indicating a great potential of SESR of propane for hydrogen production.     

Towards autothermal hydrogen production by sorption-enhanced water gas shift and methanol reforming: A thermodynamic analysis

Hydrogen production by the water gas shift reaction (WGS) is equilibrium limited. In the current study, we demonstrate that the overall efficiency of the WGS can be improved by co-feeding methanol and removing CO₂ in situ. The thermodynamics of the water gas shift and methanol reforming/WGS (methanol-to-shift, MtoS) reactions for H₂ production alone and with simultaneous CO₂ adsorption (sorption-enhanced, SEWGS and SEMtoS) were studied using a non-stoichiometric approach based on the minimisation of the Gibbs free energy. A typical composition of the effluent from a steam methane reformer was used for the shift section. The effects of temperature (450–750 K), pressure (5–30 barg), steam and methanol addition, fraction of CO₂ adsorption (0–95%) and energy efficiency of the shift systems have been investigated. Adding methanol to the feed facilitates autothermal operation of the shift unit, with and without CO₂ removal, and enhances significantly the amount of H₂ produced. For a set methanol and CO input, the MtoS and SEMtoS systems show a maximum productivity of H₂ between 523 and 593 K due to the increasing limitation of the exothermic shift reaction while the endothermic methanol steam reforming is no longer limited above 593 K. The heat of adsorption of CO₂ was found to make only a small difference to the H₂ production or the autothermal conditions.     

Hydrogen production via steam and autothermal reforming of beef tallow: A thermodynamic investigation

A thermodynamic analysis of hydrogen production via steam and autothermal reforming of beef tallow has been carried out via the Gibbs free energy minimization method. Equilibrium calculations are performed at atmospheric pressure with a wide range of temperatures (400–1200 °C), steam-to-beef tallow ratios (1–15) and oxygen-to-beef tallow ratios (0.0–2.0).     

Thermodynamic analysis of steam reforming and oxidative steam reforming of propane and butane for hydrogen production

Thermodynamic analyses of cracking, partial oxidation (POX), steam reforming (SR) and oxidative steam reforming (OSR) of butane and propane (for comparison) were performed using the Gibbs free energy minimization method under the reaction conditions of T = 250–1000 °C, steam-to-carbon ratio (S/C) of 0.5–5 and O₂/HC (hydrocarbon) ratio of 0–2.4. The simulations for the cracking and POX processes showed that olefins and acetylene can be easily generated through the cracking reactions and can be removed by adding an appropriate amount of oxygen. For SR and OSR of propane and butane, predicted carbon formation only occurred at low S/C ratios (<2) with the maximum level of carbon formation at 550–650 °C. For the thermal-neutral conditions, the TN temperatures decrease with the increase of the S/C ratio (except for O/C = 0.6) and the decrease of the O/C ratio. The simulated results for SR or OSR of propane and butane are very close under the investigated conditions.     

Thermodynamic analysis of steam reforming of ethanol and glycerine for hydrogen production

In the past few years there has been a growing interest in environmentally clean renewable sources for hydrogen production. In this context new technologies have been developed for ethanol and glycerine reforming. Hydrogen production varies significantly according to the operating conditions such as pressure, temperature and feed reactants ratio. The thermodynamic analysis provides important knowledge about the effects of those variables on the process of ethanol and glycerine reforming. The present work was aimed at analyzing the thermodynamic steam reforming of ethanol and glycerine, using Gibbs free energy minimization using actual temperature and pressure data found in the literature. The nonlinear programming model was implemented in GAMS^® and the CONOPT2 solver was used to solve the equations. The ideality in gaseous phase and the formation of solid carbon was considered. The methodology used reproduced the most relevant papers involving experimental studies and thermodynamic analysis.     

Thermodynamic analysis of hydrogen production for fuel cell via oxidative steam reforming of propane

A thermodynamic analysis of hydrogen production from propane by oxidative steam reforming (OSR) is performed with a Gibbs free energy minimization method. Addition of oxygen reduces the enthalpy of the system and facilitates the heat supply. Equilibrium compositions of OSR as a function of temperature (300, 500, 700 and 900 °C), H₂O/C₃H₈ ratio (1.0–20.0) and O₂/C₃H₈ ratio (0.0–2.0) under oxidative and thermo-neutral (TN) conditions are evaluated. The results for oxidative conditions demonstrate that at 700 °C with H₂O/C₃H₈ ratios above 7.0 and/or O₂/C₃H₈ ratios higher than 1.3 are beneficial for hydrogen production which facilitates superior hydrogen yield, i.e. close to 9.0 mol/mol propane, with coke and methane formation reactions being suppressed effectively. For TN condition, autothermal temperature and equilibrium composition have a stronger dependence on O₂/C₃H₈ ratio than on H₂O/C₃H₈ ratio. Further calculations show that the condition at 700 °C with an appropriate H₂O/C₃H₈ ratio between 7.0 and 13.0 is favorable for achieving a high hydrogen yield and a low carbon monoxide yield. Therefore, a favorable operational range is proposed to ensure the most optimized product yield.     

Thermodynamic study of hydrogen production from crude glycerol autothermal reforming for fuel cell applications

This study presents a thermodynamic analysis of hydrogen production from an autothermal reforming of crude glycerol derived from a biodiesel production process. As a composition of crude glycerol depends on feedstock and processes used in biodiesel production, a mixture of glycerol and methanol, major components in crude glycerol, at different ratios was used to investigate its effect on the autothermal reforming process. Equilibrium compositions of reforming gas obtained were determined as a function of temperature, steam to crude glycerol ratio, and oxygen to crude glycerol ratio. The results showed that at isothermal condition, raising operating temperature increases hydrogen yield, whereas increasing steam to crude glycerol and oxygen to crude glycerol ratios causes a reduction of hydrogen concentration. However, high temperature operation also promotes CO formation which would hinder the performance of low-temperature fuel cells. The steam to crude glycerol ratio is a key factor to reduce the extent of CO but a dilution effect of steam should be considered if reforming gas is fed to fuel cells. An increase in the ratio of glycerol to methanol in crude glycerol can increase the amount of hydrogen produced. In addition, an optimal operating condition of glycerol autothermal reforming at a thermoneutral condition that no external heat to sustain the reformer operation is required, was investigated.     

Hydrogen production from bio-oil: A thermodynamic analysis of sorption-enhanced chemical looping steam reforming

The steam reforming of pyrolysis bio-oil is one proposed route to low carbon hydrogen production, which may be enhanced by combination with advanced steam reforming techniques. The advanced reforming of bio-oil is investigated via a thermodynamic analysis based on the minimisation of Gibbs Energy. Conventional steam reforming (C-SR) is assessed alongside sorption-enhanced steam reforming (SE-SR), chemical looping steam reforming (CLSR) and sorption-enhanced chemical looping steam reforming (SE-CLSR). The selected CO₂ sorbent is CaO(s) and oxygen transfer material (OTM) is Ni/NiO. PEFB bio-oil is modelled as a surrogate mixture and two common model compounds, acetic acid and furfural, are also considered. A process comparison highlights the advantages of sorption-enhancement and chemical looping, including improved purity and yield, and reductions in carbon deposition and process net energy balance.The operating regime of SE-CLSR is evaluated in order to assess the impact of S/C ratio, NiO/C ratio, CaO/C ratio and temperature. Autothermal operation can be achieved for S/C ratios between 1 and 3. In autothermal operation at 30 bar, S/C ratio of 2 gives a yield of 11.8 wt%, and hydrogen purity of 96.9 mol%. Alternatively, if autothermal operation is not a priority, the yield can be improved by reducing the quantity of OTM. The thermodynamic analysis highlights the role of advanced reforming techniques in enhancing the potential of bio-oil as a source of hydrogen.     

Thermodynamic analysis of hydrogen production from glycerol autothermal reforming

In this work, thermodynamics was applied to investigate the glycerol autothermal reforming to generate hydrogen for fuel cell application. Equilibrium calculations employing the Gibbs free energy minimization were performed in a wide range of temperature (700–1000 K), steam to glycerol ratio (1–12) and oxygen to glycerol ratio (0.0–3.0). Results show that the most favorable conditions for hydrogen production are achieved with the temperatures, steam to glycerol ratios and oxygen to glycerol ratios of 900–1000 K, 9–12 and 0.0–0.4, respectively. Further, it is demonstrated that thermoneutral conditions (steam to glycerol ratio 9–12) can be obtained at oxygen to glycerol ratios of around 0.36 (at 900 K) and 0.38–0.39 (at 1000 K). Under these thermoneutral conditions, the maximum number of moles of hydrogen produced are 5.62 (900 K) and 5.43 (1000 K) with a steam to glycerol ratio of 12. Also, it should be noted that methane and carbon formation can be effectively eliminated.     

Thermodynamic analysis of propane dry and steam reforming for synthesis gas or hydrogen production

Thermodynamics was applied to investigate propane dry reforming (DR) and steam reforming (SR). Equilibrium calculations employing the Gibbs free energy minimization were performed upon a wide range of pressure (1–5 atm), temperature (700–1100 K), carbon dioxide to propane ratio (CPR, 1–12) and water to propane ratio (WPR, 1–18). From a thermodynamic perspective, it is demonstrated that DR is promising for production of synthesis gas with low hydrogen content, as opposite to SR which favours generation of synthesis gas with high hydrogen content. Complete conversion of propane was obtained for the range of pressure, temperature, CPR and WPR considered in this study. Atmospheric pressure is shown to be preferable for both DR and SR. Approximately 10 mol of synthesis gas can be produced per mole of propane at a temperature greater than 1000 K from DR when CPR is higher than 6. The optimum conditions for synthesis gas production from DR are found to be 975 K (CPR = 3) for a H₂/CO ratio of 1 and 1100 K (CPR = 1) for a H₂/CO ratio of 2. The greatest CO₂ conversion (95%) can be obtained also at 1100 K and CPR = 1. Preferential conditions for hydrogen production from SR are achieved with the temperatures between 925 and 975 K and WPRs of 12–18. The maximum number of moles of hydrogen produced is 9.1 (925 K and WPR = 18). Under conditions that favour hydrogen production, methane and carbon formation can be eliminated to negligible level.     

Properties of thermodynamic equilibrium-based methane autothermal reforming to generate hydrogen

The characteristics of methane autothermal reforming to generate hydrogen were studied with thermodynamic equilibrium constant method. Results show that the methane steam reforming reaction is prone to backward at low temperature, and there is an inflection point temperature that the reaction turns forward. When steam–methane molar ratio is 2, the inflection point temperature increases with raising air–methane molar ratio. When air–methane molar ratio is 1, the inflection point temperature maintains between 700 and 800 K. Hydrogen yield increases firstly and then decreases with elevated temperature. The increase of air–methane molar ratio leads to a lower hydrogen production when temperature exceeds 1000 K. Increasing steam–methane molar ratio promotes the hydrogen production. Methane autothermal reforming occurs much more easily when temperature keeps at 1000 K and the molar ratio of air–methane and steam–methane is 1 and 2 respectively. Changing the steam–methane molar ratio can regulate H₂/CO molar ratio.     

Microwave-activated methanol steam reforming for hydrogen production

Methanol steam reforming (MSR) was carried out in a catalytic packed bed reactor under electrical and microwave heating using the two most common catalysts for this process-CuZnO/Al₂O₃ and PdZnO/Al₂O₃. Significant two-dimensional temperature gradients were found, especially in the latter case. Our results show that for the same average bed temperature, methanol conversion is higher under microwave heating (>10%). On the other hand, the product distribution is not affected by the heating mode. We demonstrate that even in cases where the maximum temperature along the entire height of the bed is significantly higher under electrical heating, conversion is either higher in the microwave case or approximately the same between the two heating modes. Finally, our experimental data indicate that a given methanol conversion can be achieved with lower net heat input to the reactor under microwave heating. This does not mean lower total energy consumption in the microwave process due to the limitations in the magnetron efficiency and the reflected power. However, it may be an implicit indication of higher temperature at metal sites than in bulk phase (microscale hot spot formation) due to the selective heating principle.     

A thermodynamic equilibrium analysis of hydrogen and synthesis gas production from steam reforming of acetic acid and acetone blends as bio-oil model compounds

Thermodynamic analysis of steam reforming of blends of two model oxygenates, acetic acid and acetone, representing carboxylic acids and ketones in bio-oil is performed to investigate the effects of their potential interactions on hydrogen yield, synthesis gas composition and progress of reaction network. The results show that both acetic acid and acetone reach complete conversion at all operating conditions. Higher S/C molar ratio results in higher H₂ and CO₂ yields for both acetic acid and acetone. With the increase in pressure, H₂ and CO yields are diminished whereas CH₄ and CO₂ yields are enhanced. H₂ and CO₂ yields increase with the decrease in acetone concentration in the feed blend. CO and CH₄ production are affected adversely for acetic acid rich blends. The maximum H₂ yield values are 75.54%, 78.34%, 80.09%, 81.78% and 84.17% at 700 °C for acetic acid/acetone blends of 0.0/1.0, 0.3/0.7, 0.5/0.5, 0.7/0.3 and 1.0/0.0, respectively.     

Thermodynamic analysis of hydrogen production via autothermal steam reforming of selected components of aqueous bio-oil fraction

From a technical and economic point of view, autothermal steam reforming offers many advantages, as it minimizes heat load demand in the reformer. Bio-oil, the liquid product of biomass pyrolysis, can be effectively converted to a hydrogen-rich stream. Autothermal steam reforming of selected compounds of bio-oil was investigated using thermodynamic analysis. Equilibrium calculations employing Gibbs free energy minimization were performed for acetic acid, acetone and ethylene glycol in a broad range of temperature (400–1300 K), steam to fuel ratio (1–9) and pressure (1–20 atm) values. The optimal O₂/fuel ratio to achieve thermoneutral conditions was calculated under all operating conditions. Hydrogen-rich gas is produced at temperatures higher than 700 K with the maximum yield attained at 900 K. The ratio of steam to fuel and the pressure determine to a great extent the equilibrium hydrogen concentration. The heat demand of the reformer, as expressed by the required amount of oxygen, varies with temperature, steam to fuel ratio and pressure, as well as the type of oxygenate compound used. When the required oxygen enters the system at the reforming temperature, autothermal steam reforming results in hydrogen yield around 20% lower than the yield by steam reforming because part of the organic feed is consumed in the combustion reaction. Autothermicity was also calculated for the whole cycle, including preheating of the organic feed to the reactor temperature and the reforming reaction itself. The oxygen demand in such a case is much higher, while the amount of hydrogen produced is drastically reduced.     

Thermodynamic analysis of hydrogen production by autothermal reforming of ethanol

Ethanol steam reforming (ESR) is a strong endothermic reaction and ideally it only produces hydrogen and carbon dioxide.     

Thermodynamic analysis of ethanol steam reforming using Gibbs energy minimization method: A detailed study of the conditions of carbon deposition

In this paper, a thermodynamic analysis of ethanol/water system, using the Gibbs energy minimization method, has been carried out. A mathematical relationship between Lagrange's multipliers and carbon activity in the gas phase was deduced. From this, it was possible to calculate carbon activities in both stable and metastable systems. For the system that corresponds to ethanol steam reforming at very low contact times, composed mainly of ethylene and acetaldehyde, carbon activities were always much greater than unity over the whole temperature range, changing from 1.2 × 10⁷ at 400 K to 1.1 × 10⁴ at 1200 K. Furthermore, there was practically no effect of the inlet steam/ethanol ratio on carbon activity values. These results indicate that such a system is highly favorable to carbon formation. On the other hand, by considering a more stable system, in order to represent high contact times, it was observed that carbon activities are much lower and depend greatly on the inlet steam/ethanol ratio employed. Besides, the complete conversion of ethylene and acetaldehyde into other species, such as CO, CO₂, CH₄ and H₂, lowers the total Gibbs energy of the system. By computing carbon activities in experimental systems, it was also possible to explain deviations between thermodynamic analysis and experimental results regarding carbon deposition.