CPR1000蒸汽发生器二次侧三维稳态热工水力分析

采用三维稳态分析软件GENEPI,对CPR1000蒸汽发生器二次侧管束区进行了热工水力计算,利用多孔介质及局部阻力系数来表征传热管及各几何部件的复杂结构和压降影响,得到了二次侧管束区流场、温度场等的分布情况。计算结果表明:管束区最大干度为0.3;将典型传热管的动能数据提供给流致振动软件进行计算分析,结果显示在本工况下,传热管的流致振动在可接受范围内;对管板附近的流场及温度场进行分析,预测了此模型及工况下的泥渣沉积区域,为排污管的设计提供了输入数据。计算结果验证了CPR1000蒸汽发生器二次侧管束区设计的合理性。     

蒸汽发生器全尺寸汽水分离装置模型开发

汽水分离装置是核动力系统蒸汽发生器(SG)重要组成部分。目前针对汽水分离装置的研究包含试验与模拟两种方法,受限于成本和计算资源,现有研究主要是对汽水分离装置中单一旋叶式分离器或波形板干燥器开展。但在SG不同位置处分离器或干燥器入口参数不相同,存在负荷不均问题。为此,本研究基于已有分离器和干燥器分离效率计算模型,对汽水分离装置适当简化,开发SG全尺寸汽水分离装置模型。研究SG中不同位置处分离器和干燥器分离效率分布特性以及干燥器液滴负荷不均情况。计算结果可为SG汽水分离装置设计提供参考,开发的汽水分离模型已植入自主化SG全流域热工水力计算分析程序STAF。     

蒸汽发生器传热管束过冷沸腾区两相流动数值模拟

基于两流体欧拉数学模型结合RPI壁面沸腾模型,利用大型商用CFD软件ANSYS CFX 12.0对蒸汽发生器传热管束过冷沸腾区一次侧、壁面和二次侧耦合传热过程进行了数值模拟。研究了三叶梅花孔支撑板和不同入口过冷度条件下蒸汽发生器传热管束内的流动沸腾现象,得到一、二次侧流场与温度场,二次侧空泡份额分布,支撑板梅花孔局部的流动状况及不同入口过冷度对蒸汽发生器热工水力特性的影响。数值模拟结果表明,三叶梅花孔支撑板的存在及不同入口过冷度对蒸汽发生器传热管束过冷沸腾区域的热工水力特性影响显著。     

蒸汽发生器一级汽水分离器两相流动数值模拟

采用计算流体力学方法并采用非结构化网格和多块网格技术对流动区域进行了网格划分,用两相流模型对蒸汽发生器一级汽水分离器两相流动进行模拟,得到了汽-液两相流动细节,将出口蒸汽干度与蒸汽发生器热工水力专用计算程序计算结果进行比较,吻合良好.     

高温气冷堆螺旋管式直流蒸汽发生器热工水力学

高温气冷堆蒸汽发生器具有一次侧氦气工质、二次侧直流、螺旋管结构、工作温度高等特点,其热工水力特性与传统压水堆自然循环蒸汽发生器存在很大区别。针对高温气冷堆蒸汽发生器的特点,对其基础热工水力及特有热工水力学问题进行了阐述,主要包括螺旋管内单相及两相流阻及换热计算、横掠螺旋管束流阻及换热计算、温度均匀性及两相流不稳定性等。同时介绍了清华大学核能与新能源技术研究院针对高温气冷堆蒸汽发生器热工设计、温度均匀性及两相流不稳定性等热工水力学问题所开发的一维稳态程序、一维瞬态程序、二维分析程序和方法,并对分析结果和结论进行了讨论。相关研究方法、程序和结论对其他相似参数螺旋管和直管式直流蒸汽发生器具有参考和借鉴意义。     

高温气冷堆螺旋管式直流蒸汽发生器热工水力学

高温气冷堆蒸汽发生器具有一次侧氦气工质、二次侧直流、螺旋管结构、工作温度高等特点,其热工水力特性与传统压水堆自然循环蒸汽发生器存在很大区别。针对高温气冷堆蒸汽发生器的特点,对其基础热工水力及特有热工水力学问题进行了阐述,主要包括螺旋管内单相及两相流阻及换热计算、横掠螺旋管束流阻及换热计算、温度均匀性及两相流不稳定性等。同时介绍了清华大学核能与新能源技术研究院针对高温气冷堆蒸汽发生器热工设计、温度均匀性及两相流不稳定性等热工水力学问题所开发的一维稳态程序、一维瞬态程序、二维分析程序和方法,并对分析结果和结论进行了讨论。相关研究方法、程序和结论对其他相似参数螺旋管和直管式直流蒸汽发生器具有参考和借鉴意义。     

CAP1400蒸汽发生器汽水分离装置研究

汽水分离装置是蒸汽发生器中的主要部件,其性能不仅会影响蒸汽发生器水力循环特性及水位适用性,决定上部尺寸大小,而且会影响汽轮机的正常运行。对CAP1400核电厂蒸汽发生器汽水分离装置进行了不同蒸汽负荷、饱和水量及高水位和正常水位等试验工况下的热态性能试验,获得了SP3型初级分离器与P3X型干燥器组合随蒸汽负荷、饱和水量、水位变化的分离特性。通过初级分离器和干燥器的阻力测量,分别获得了分离器和干燥器的阻力特性,对CAP1400蒸汽发生器的设计研发起到支撑作用。     

基于CFD的汽水分离再热器分析计算研究

通过三维数值模拟研究了实际运行工况下汽水分离再热器（MSR）内部流场细节,并对比了2种不同孔板开孔方式对波形板前气流均匀性的影响。采用标准k-ε湍流模型结合标准壁面函数对MSR内部进行了CFD气相流场三维模拟,其中孔板、波形板和管束采用多孔介质模型,通过UDF调整孔板开孔率,防冲板简化为多孔跃升边界。结果表明：分析计算结果与空气动力学试验结果数据绝对值或数据增减幅度较好符合;在保持平均开孔率与均匀开孔相同的基础上,非均匀开孔的波形板前气流速度更为均匀;蒸汽通过孔板和分离器的总压降不大于14 kPa,满足分离装置的压损设计要求,其中蒸汽的再热器管束的压降占整个流线压降的比例较大。     

秦山核电厂主蒸汽管道破裂事故的RELAP5／MOD2分析

通过使用RELAP5/MOD2程序对秦山核电厂主蒸汽管道破裂事故的计算,对该程序的临界流模型和传热模型进行分析,并与其它大型热工水力分析程序的计算结果及实验结果进行比较。在计算过程中,对RELAP5/MOD2程序汽水分离器模型的使用进行修正,使之符合核电厂安全评审计算的要求。     

基于RELAP5的螺旋管蒸汽发生器热工水力程序研发与验证

由于较高的换热效率和紧凑的结构设计,螺旋管式直流蒸汽发生器（HCOTSG）在多种模块化小型堆的设计中得到了广泛应用。RELAP5作为广泛应用于反应堆热工水力特性分析的大型系统程序之一,采用的热工水力关系式仅针对直管模型开发,不适用于HCOTSG一次侧和二次侧。本文选用螺旋管及横掠管束的热工水力模型,基于RELAP5程序开发了HCOTSG模块。采用实验数据及程序对比等方式对螺旋管模块的流动和换热模型进行了单独验证,利用开发的RELAP5-HCOTSG程序针对国际革新安全反应堆（IRIS）的蒸汽发生器设计进行了整体的热工水力模拟,与原始RELAP5的计算相比,RELAP5-HCOTSG程序计算得到的热工水力参数与设计值符合良好,确认了本文开发的程序模块在HCOTSG热工水力分析中的适用性。     

Preparation of Zn/TiO2 powder and its photocatalytic performance for oxidation of P-nitrophenol

Zn-doped TiO2 catalysts were prepared using a sol-gel method and characterized by XPS,UV-Vis, BET, XRD in this study. Under the irradiation of simulant sunlight, the photocatalytic activity for the degradation of p-nitrophenol was studied too. After irradiation for 2.5 h, the degradation percentage of p-nitrophenol could rise to more than 80 %. The results showed that the spectrum absorption band edge of Zn/TiO2 powder does not broaden obviously comparing with pure TiO2 powder. Zinc exists as Zn （11）. When calcined at 973 K, there is a new phase as ZnTiO3 in Zn/TiO2 catalyst. The order of photocatalytic activity of Zn/TiO2 catalysts calcined at different temperatures for p-nitrophenol is 773 K 〉 673 K 〉 873 K 〉 573 K 〉 973 K and the photocatalytic activity of Zn/TiO2 catalyst calcined at 773 K is better than TiO2 catalysts heated at the same temperature, and outclasses that of commercial TiO2 catalyst. It also showed that the photocatalytic degradation of p-nitrophenol follows first-order kinetics under the irradiation of simulant sunlight.     

Current status of radiation therapy for prostate cancer

Radiotherapy for the treatment of prostate cancer has been extensively explored in the past. Along with the comprehensive understanding of the biology of prostate cancer and rapid advances in terms of technology, the out- come of treatment for the patients with prostate cancer has improved. The authors review radiotherapy as the primary treatment for the disease, with particular emphasis on the technological advances from both the radiobiological and radiophysics aspects. Nonconventional fractionated irradiation like hyper- or hypo-fractionation has been imple- mented in the clinic, the final results still need to be confirmed in the future. Technological advances like IMRT, IGRT, in the last two decades have significantly improved the delivery of external radiotherapy to the prostate. This has re- sulted in an overall increase in the total dose that can be safely delivered to the prostate, which has led to modest im- provements in the biochemical outcome. However, establishing the standard therapy for prostate cancer remains con- troversial. It is hoped that the next decades will bring continued advances in the development of biologicals that will further improve current clinical outcomes.     

The control system for SSRF injection and extraction

This paper introduces the injection and extraction control system design for SSRF,which is a distributed control system aimed at stability and reliability of the pulse power supplies,PPS(Personnel Protection System)and MPS(Machine Protection System).The hardware environment is mainly based on PLC(Programmable Logic Con- troller),and ARM(Advanced RISC Machine)is also applied for studying stability of the power supplies.WinCC and EPICS(Experimental Physics and Industrial Control System)have been selected as the platforms of SCADA(Super- visory Control and Data Acquisition).For unifying the interfacing to the control computer,all front-end equipments are connected via Industrial Ethemet.     

水平管内含空气蒸汽强制对流冷凝换热模型研究

为研究含空气蒸汽在水平管内强制对流冷凝换热特性,基于对传热传质过程的分析,建立了管内为环状流与波状流条件下的流动冷凝换热模型。从潜热、显热和液膜3个环节对整个换热过程进行建模,最终得到计算局部冷凝换热系数的理论关系式。模型预测结果与实验数据的对比表明,二者相对偏差在±20%以内,验证了该换热模型的准确性与适用性。通过进一步的研究发现：从换热管入口至出口,随着冷凝的进行,管内换热主要热阻由液膜热阻向气液界面的凝结热阻转变;主流气体对流换热过程基本可忽略。     

Investigations on landmine detection by BF3 detector

Experiments were carried out to investigate the possible use of neutron backscattering for the detection of polyethylene (PE) sample buried in the soil. In detection of landmine by neutrons, the neutron detector and its shield play an important role. In this paper, the effects of graphite, heavy water, polyethylene and boric acid moderators on the flux of back scattered neutrons were investigated. We have also experimentally verified the effect of BF3 detector shield and obtained good agreement with theory.     

Web Services interface of SSRF archive data analysis system

Accelerator database stores various static parameters and real-time data of accelerator. SSRF (Shanghai Synchrotron Radiation Facility) adopts relational database to save the data. We developed a data retrieval system based on XML Web Services for accessing the archive data. It includes a bottom layer interface and an interface applicable for accelerator physics. Client samples exemplifying how to consume the interface are given. The users can browse, retrieve and plot data by the client samples. Also, we give a method to test its stability. The test result and performance are described.     

有效探测面积大于1000 cm2的正比计数器测量系统性能测试

为对自制的活性面积高达1 000 cm²的大面积源进行表面发射率定值,同时作为现有2πα、2πβ表面发射率标准装置能力的扩充,研制了一套内置式大面积2π多丝正比计数器测量系统,并利用活性区直径为8 mm的²⁴¹Am点源及活性区面积为10 cm×15 cm的大面积²⁴¹Am和⁹⁰Sr-⁹⁰Y源对其进行计量学性能测试。结果表明：计数器内计数响应均匀性优于±0.4%,有效探测面积达1 400 cm²;所得²⁴¹Am源高压坪曲线的坪长为1 400 V,坪斜为0.27%/100 V,坪区内计数变化为0.87%;⁹⁰Sr-⁹⁰Y源高压坪曲线的坪长为300 V,坪斜为0.75%/100 V,坪区内计数变化为0.80%;10次测量重复性好于0.4%,8 h内短期稳定性好于0.3%,1 a内长期稳定性好于0.8%。     

Assessment of radioactivity levels in some oil samples from the western desert, Egypt

Distributions of natural gamma-emitting radionuclides were determined in 93 oil samples collected from some petroleum fields in the western desert of Egypt. The radioisotope activities in the area under investigation lay in the range of (21 ± 4) to (38 ± 13) Bq?L-1 for 226Ra, (9 ± 2) to (15 ± 5) Bq?L-1 for 232Th, and (154 ± 28) to (303 ± 54) Bq?L-1 for 40K. The mean values were 27, 12, and 201 Bq?L-1, respectively. Among oils, variations in radionuclide ac- tivities could be on account of differences in TDS, HCO3, and Ba, with high or low pH. In this environment, oil prop- erties differently affected the mobilization of natural radionuclides. The range of 226Ra variation had been compared with available data from other countries. The calculated absorbed dose rate ranged from 22.33 to 32.66 nGy?h-1 in lo- cation (B) and (E) respectively, which was less than the accepted value.     

Preparation and properties of 117m Sn(IV)-TTHMP in in-vitro and in small animals

In this work,TTHMP was synthesized and labelled with 117m Sn.The preparation conditions,stability and lipophilicity of 117m Sn(IV)-TTHMP were investigated.Biodistribution of the complex in rabbits and mice was studied.It was found that the quantity of TTHMP and pH value of the prepararion solution had vital effects on the labeling yield of 117m Sn(IV)-TTHMP.It was also found that 117m Sn(IV)-TTHMP was hydrophilic and stable at room temperature and 37℃ in open air 117m Sn(IV)-TTHMP showed unexpectedly high bone uptake and bone-to-blood ratio in the animals.This made it potentially useful as an reagent for skeletal scintigraphy and radiotherapy of bone tumors.     

Gamma radiation levels in the ambient environment of the QNPP Base

Monitoring results of gamma dose rate level in 1992～2004 in the ambient environment of the Qinshan Nuclear Power Plants(QNPP)Base,the northeast of Zhejiang Province,are reported in this paper.It is shown that the gamma dose rate of five monitoring sites of 2.5 km to QNPP Base is 84～113 nGy/h,with an average of 96 nGy/h in the 13 years.The average value is close to the background level of 93 nGy/h prior to operation of the QNPP Base,and is lower than the monitoring result of 101 nGy/h at the reference site in Hangzhou City.Within 50 km from the QNPP Base,the cumulative dose rate of the thermoluminescent dosimeter(TLD)is 90 nGy/h,which is lower than the back- ground level of 111 nGy/h.