Electrooxidation of sulfide by cobalt pentacyanonitrosylferrate film on glassy carbon electrode by cyclic voltammetry

A glassy carbon (GC) electrode was modified with cobalt pentacyanonitrosylferrate (CoPCNF) film. Cyclic voltammetry (CV) of the CoPCNF onto the GC (CoPCNF/GC) shows a redox couple (Fe^III/Fe^II) with a standard potential (E^0′) of 580 mV. The current ratio I_pa/I_pc remains almost 1, and a peak separation (ΔE_p) of 106 mV is observed in 0.5 M KNO₃ as the supporting electrolyte. Anodic peak currents were found to be linearly proportional to the scan rate between 10 and 200 mV s⁻¹, indicating an adsorption-controlled process. The redox couple of the CoPCNF film presents an electrocatalytic response to sulfide in aqueous solution. The analytical curve was linear in the concentration range of 7.5 × 10⁻⁵ to 7.7 × 10⁻⁴ M with a detection limit of 4.6 × 10⁻⁵ M for sulfide ions in 0.5 M KNO₃ solution.     

Cobalt oxide nanocomposites and their electrocatalytic behavior for oxygen evolution reaction

In this work, we have described the simple preparation method of cobalt oxide nanocomposites where cobalt oxide nanoparticles were grown on the surface of carbon nanotube, graphene oxide and graphene (Co₃O₄@CNT, Co₃O₄@GO, Co₃O₄@G). The as-grown Co₃O₄@CNT, Co₃O₄@GO, Co₃O₄@G were investigated for H₂O oxidation. The nanoparticles displayed high activity toward oxygen evolution. Further, the stability of the catalysts were tested in alkaline solution, which exhibited good stability. Among all nanoparticles, Co₃O₄@G exhibited higher current density at lower overpotential and also exhibited lower Tafel slope (157.1 mV dec⁻¹) as compared to Co₃O₄@CNT and Co₃O₄@GO. The Co₃O₄@G delivered a current density of 10 mAcm⁻² at 0.8 V (overpotential 535 V versus Ag/AgCl) in 0.1 M KOH solution, which is superior than many electrocatalysts reported for oxygen evolution so far. The good electrocatalytic performance might be due to the structural features of Co₃O₄@G, which cause enhancement of oxygen evolution activity.     

Immobilization of Nafion-ordered mesoporous carbon on a glassy carbon electrode: Application to the detection of epinephrine

A stable suspension of ordered mesoporous carbon (OMC) was obtained by dispersing OMC in a solution of Nafion. By coating the suspension onto glassy carbon (GC) electrode, cyclic voltammetry was used to evaluate the electrochemical behaviors of Nafion-OMC-modified GC (Nafion-OMC/GC) electrode in 0.1 mmol L⁻¹ hexaammineruthenium(III) chloride (Ru(NH₃)₆Cl₃)/0.1 mol L⁻¹ KCl solution, where Nafion-OMC/GC electrode shows a faster electron transfer rate as compared with OMC/GC, Nafion/GC and GC electrodes. Due to the unique properties of Nafion-OMC, an obvious decrease in the overvoltage of the epinephrine (EP) oxidation (ca. 100 mV at pH 4.1 and 115 mV at pH 7.0) as well as a dramatic increase in the peak current (12 times at pH 4.1 and 6 times at pH 7.0) was observed at Nafion-OMC/GC electrode compared to that seen at GC electrode. By combining the advantages of OMC with those of Nafion, the anodic peak of EP and that of ascorbic acid (AA) were separated successfully (by ca. 144-270 mV) in the pH range of 2.0-10.0, which may make Nafion-OMC/GC electrode potential for selective determination of EP in the presence of AA at a broad pH range. As an EP sensor, the EP amperometric response at Nafion-OMC/GC electrode in pH 7.0 PBS is extremely stable, with 99% of the initial activity remaining (compared to 32% at GC surface) after 120 min stirring of 0.20 mmol L⁻¹ EP. And Nafion-OMC/GC electrode can be used to readily detect the physiological concentration of EP at pH 7.0. These make Nafion-OMC/GC electrode potential candidates for stable and efficient electrochemical sensor for the detection of EP. The solubilization of OMC by Nafion may provide a route to more precise manipulation, and functionalization for the construction of OMC-based sensors, as well as allowing OMC to be introduced to biologically relevant systems.     

Nano-structured Ni(II)-curcumin modified glassy carbon electrode for electrocatalytic oxidation of fructose

A nano-structured Ni(II)-curcumin (curcumin: 1,7-bis[4-hydroxy-3-methoxyphenyl]-1,6-heptadiene-3,5-dione) film is electrodeposited on a glassy carbon electrode in alkaline solution. The morphology of polyNi(II)-curcumin (NC) was investigated by scanning electron microscopy (SEM). The SEM results show NC has a nano-globular structure in the range 20-50 nm. Using cyclic voltammetry, linear sweep voltammetry, chronoamperometry, steady-state polarization measurements and electrochemical impedance spectroscopy (EIS) showed that the nano-structure NC film acts as an efficient material for the electrocatalytic oxidation of fructose. According to the voltammetric studies, the increase in the anodic peak current and subsequent decrease in the corresponding cathodic current, fructose was oxidized on the electrode surface via an electrocatalytic mechanism. The EIS results show that the charge-transfer resistance has as a function of fructose concentration, time interval and applied potential. The increase in the fructose concentration and time interval in fructose solution results in enhanced charge transfer resistance in Nyquist plots. The EIS results indicate that fructose electrooxidation at various potentials shows different impedance behaviors. At lower potentials, a semicircle is observed in the first quadrant of impedance plot. With further increase of the potential, a transition of the semicircle from the first to the second quadrant occurs. Also, the results obtained show that the rate of fructose electrooxidation depends on concentration of OH⁻. Electron transfer coefficient, diffusion coefficient and rate constant of the electrocatalytic oxidation reaction are obtained. The modified electrode was used as a sensor for determination of fructose with a good dynamic range and a low detection limit.     

Highly sensitive and simultaneous determination of hydroquinone and catechol at poly(thionine) modified glassy carbon electrode

A simple and highly sensitive electrochemical method for the simultaneous and quantitative detection of hydroquinone (HQ) and catechol (CT) was developed, based on a poly(thionine)-modified glassy carbon electrode (GCE). The modified electrode showed excellent electrocatalytic activity and reversibility towards the oxidation of both HQ and CT in 0.1 M phosphate buffer solution (PBS, pH 7.0). The peak-to-peak separations (ΔE_p) between oxidation and reduction waves in CV were decreased significantly from 262 and 204 mV at the bare GCE, to 63 and 56 mV, respectively for HQ and CT at the poly(thionine) modified GCE. Furthermore, the redox responses from the mixture of HQ and CT were easily resolved in both CV and DPV due to a difference in the catalytic activity of the modified GCE to each component. The peak potential separation of ca. 0.1 V was large enough for the simultaneous determination of HQ and CT electrochemically. The oxidation peak currents of HQ and CT were linear over the range from 1 to 120 μM in the presence of 100 and 200 μM of HQ and CT, respectively. The modified electrode showed very high sensitivity of 1.8 and 1.2 μA μM⁻¹ cm⁻² for HQ and CT, respectively. The detection limits (S/N = 3) for HQ and CT were 30 and 25 nM, respectively. The developed sensor was successfully examined for real sample analysis with tap water and revealed stable and reliable recovery data.     

Preparation and electrochemistry of cadmium pentacyanonitrosylferrate film modified glassy carbon electrode

A glassy carbon (GC) electrode surface was modified with a cadmium pentacyanonitrosylferrate (CdPCNF) film as a novel electrode material. The modification procedure of the GC surface includes two consecutive procedures: (i) the electrodeposition of metallic cadmium on the GC electrode surface from a CdCl₂ solution and (ii) the chemical transformation of the deposited cadmium to the CdPCNF films in 0.05 M Na₂[Fe(CN)₅NO] + 0.5 M KNO₃ solution. The modified GC electrode showed a well-defined redox couple due to [Cd^IIFe^III/II(CN)₅NO]^0/−1 system. The effects of supporting electrolytes and solution pH were studied on the electrochemical behavior of the modified electrode. The diffusion coefficients of alkali-metal cations in the film (D), the transfer coefficient (α) and the charge transfer rate constant at the modifying film | electrode interface (k_s), were calculated in the presence of various alkali-metal cations. The stability of the modified electrode was investigated under various experimental conditions.     

Poly-phenothiazine derivative-modified glassy carbon electrode for NADH electrocatalytic oxidation

Electropolymerization of a new phenothiazine derivative (bis-phenothiazin-3-yl methane; BPhM) on glassy carbon (GC) electrode generates a conducting film of poly-BPhM, in stable contact with the electrode surface. The heterogeneous electron-transfer process corresponding to the modified electrode is characterized by a high rate constant (50.4 s⁻¹, pH 7). The GC/poly-BPhM electrode shows excellent electrocatalytic activity toward NADH oxidation. The rate constant for catalytic NADH oxidation, estimated from rotating disk electrode (RDE) measurements and extrapolated to zero concentration of NADH, was found to be 9.4 × 10⁴ M⁻¹ s⁻¹ (pH 7). The amperometric detection of NADH, at +200 mV vs. SCE, is described by the following electroanalytical parameters: a sensitivity of 1.82 mA M⁻¹, a detection limit of 2 μM and a linear domain up to 0.1 mM NADH.     

A study of the electro-catalytic oxidation of methanol on a cobalt hydroxide modified glassy carbon electrode

Cobalt hydroxide modified glassy carbon electrodes (CHM/GC) prepared by the anodic deposition in presence of tartrate ions have been used for the electro-catalytic oxidation of methanol in alkaline solutions where the methods of cyclic voltammetery (CV), chronoamperometry (CA) and impedance spectroscopy (IS) have been employed. In CV studies, in the presence of methanol the peak current of the oxidation of cobalt hydroxide increase is followed by a decrease in the corresponding cathodic current. This suggests that the oxidation of methanol is being catalysed through the mediated electron transfer across the cobalt hydroxide layer comprising of cobalt ions of various valence states. A mechanism based on the electro-chemical generation of Co(IV) active sites and their subsequent consumptions by methanol have been discussed and the corresponding rate law under the control of charge transfer has been developed and kinetic parameters have been derived. In this context the charge transfer resistance accessible both theoretically and through the IS studies have been used as a criteria. Under the CA regimes the reaction followed a Cottrellian behaviour.     

Hematoxylin multi-wall carbon nanotubes modified glassy carbon electrode for electrocatalytic oxidation of hydrazine

A new hydrazine sensor has been fabricated by immobilizing hematoxylin at the surface of a glassy carbon electrode (GCE) modified with multi-wall carbon nanotube (MWCNT). The adsorbed thin films of hematoxylin on the MWCNT modified GCE show one pair of peaks with surface confined characteristics. The hematoxylin MWCNT (HMWCNT) modified GCE shows highly catalytic activity toward hydrazine electro-oxidation. The results show that the peak potential of hydrazine at HMWCNT modified GCE surface shifted by about 167 and 255 mV toward negative values compared with that at an MWCNT and activated modified GCE surface, respectively. In addition, at HMWCNT modified electrode surface remarkably improvement the sensitivity of determination of hydrazine. The kinetic parameters, such as the electron transfer coefficient, α, and the standard heterogeneous rate constant, k⁰, for oxidation of hydrazine at the HMWCNT modified GCE were determined and also is shown that the heterogeneous rate constant, k′, is strongly potential dependent. The overall number of electron involved in the catalytic oxidation of hydrazine and the number of electrons involved in the rate-determining steps are 2 and 1, respectively. The amperometric detection of hydrazine is carried out at 220 mV in 0.1 M phosphate buffer solution (pH 7) with linear response range 2.0-122.8 μM hydrazine, detection limit of 0.68 μM and sensitivity of 0.0208 μA μM⁻¹. Finally the amperometric response for hydrazine determination is reproducible, fast and extremely stable, with no loss in sensitivity over a continual 400 s operation.     

Electrochemical study on cobalt film modified glassy carbon electrode and its application

A novel electroactive material for ascorbic acid (AA) determination was successfully prepared by plating/potential cycling method. The cobalt film was first deposited on the surface of glassy carbon electrode (GCE) in CoSO₄ solution by potential cycling, and then a cobalt film on the surface of GCE was activated by potential cycling in 0.1 mol L⁻¹ NaOH. The electrochemical performance of the resulted film (Co/GCE) and factors affecting its electrochemical activity were investigated by cyclic voltammetry and amperometry. This film electrode exhibited good electrocatalytic activity to the oxidation of AA. This biosensor had a fast response of AA less than 3 s and excellent linear relationships were obtained in the concentration range of 3 × 10⁻⁷ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 2 × 10⁻⁷ mol L⁻¹ (S/N = 3) under the optimum conditions. Moreover, the selectivity, stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Characterization of self-assembled monolayers of iron and cobalt octaalkylthiosubstituted phthalocyanines and their use in nitrite electrocatalytic oxidation

Cobalt and iron phenylthiosubstituted phthalocyanines have been deposited on Au electrode surfaces through the self-assembled monolayer (SAM) technique. The so formed layers were studied using voltammetric and impedance techniques. These SAMs blocked a number of Faradic processes and electrocatalyzed the oxidation of nitrite. The electrocatalytic parameters of the cobalt and iron phenylthiosubstituted phthalocyanines deposited on Au electrodes in nitrite solution were studied. Nitrite overpotentials which are lower than ever reported were obtained in this work for the iron phenylthiosubstituted phthalocyanines with very high stability.     

预处理玻碳电极线性扫描伏安法测定槲皮素的研究

运用循环伏安法、线性扫描伏安法等测试技术研究了槲皮素在预处理玻碳电极上的电化学行为,建立了一种直接测定槲皮素的电化学分析方法。结果表明,与裸玻碳电极相比,预处理玻碳电极能显著提高槲皮素的氧化峰电流。在优化的实验条件下,氧化峰电流与槲皮素浓度在1.0×10-7～2.0×10-5mol/L范围内呈良好的线性关系,最低检测限为6.2×10-8mol/L。该方法简便、快捷、准确、灵敏度高。本法用于芦丁水解产物槲皮素的测定,效果良好。     

Electrochemical behavior of catechol, resorcinol and hydroquinone at graphene–chitosan composite film modified glassy carbon electrode and their simultaneous determination in water samples

Graphene–chitosan composite film modified glassy carbon electrode was prepared and characterized. The fabricated electrode showed excellent electrochemical catalytic activities towards the oxidation of catechol (CT), resorcinol (RS) and hydroquinone (HQ). The oxidation overpotentials of CT, RS and HQ decreased significantly and the corresponding oxidation currents increased remarkably compared with those obtained at the bare GCE and chitosan modified GCE. Some kinetic parameters, such as the electron transfer number (n), proton transfer number (m), charge transfer coefficient (α) and the apparent heterogeneous electron transfer rate constant (k_s), were calculated. Differential pulse voltammetry was used for the simultaneous determination of CT, RS and HQ in their ternary mixture. The peak-to-peak potential separations between CT and RS, RS and HQ, and HQ and CT were 0.388, 0.484 and 0.096 V, respectively. The calibration curves for CT, RS and HQ were obtained in the range of 1 × 10⁻⁶ to 4 × 10⁻⁴, 1 × 10⁻⁶ to 5.5 × 10⁻⁴ and 1 × 10⁻⁶ to 3 × 10⁻⁴ mol L⁻¹, respectively. The detection limits were 7.5 × 10⁻⁷ mol L⁻¹ (S/N = 3).     

Preparation of tungsten oxide nanoporous thin film at carbon ceramic electrode for electrocatalytic applications

The electrodeposition of nanoporous tungsten oxide (WO₃) on the surface of carbon ceramic electrode (CCE) was described. The morphology of the WO₃ modified electrode was characterized by scanning electron microscopy and X-ray diffraction. The modified electrode was utilized as an electrochemical hydrogen peroxide sensor in a low potential with a high sensitivity and selectivity. The role of supporting matrix on the sensitivity of modified electrode was studied. The detection limit of 0.26 μM (S/N = 3) and the sensitivity of 16.8 A M⁻¹ cm⁻² were compared with some other metal oxides hydrogen peroxide sensors. The modified electrode has exhibited good reproducibility, long-term stability and negligible interference of some inorganic and biological compounds.     

Noble-metal-free cobalt hydroxide nanosheets for efficient electrocatalytic oxidation

Cobalt hydroxide has been emerging as a promising catalyst for the electrocatalytic oxidation reactions, including the oxygen evolution reaction (OER) and glucose oxidation reaction (GOR). Herein, we prepared cobalt hydroxide nanoparticles (CoHP) and cobalt hydroxide nanosheets (CoHS) on nickel foam. In the electrocatalytic OER, CoHS shows an overpotential of 306 mV at a current density of 10 mA·cm^–2. This is enhanced as compared with that of CoHP (367 mV at 10 mA·cm^–2). In addition, CoHS also exhibits an improved performance in the electrocatalytic GOR. The improved electrocatalytic performance of CoHS could be due to the higher ability of the two-dimensional nanosheets on CoHS in electron transfer. These results are useful for fabricating efficient catalysts for electrocatalytic oxidation reactions.     

Electrocatalytic oxidation of deferiprone and its determination on a carbon nanotube-modified glassy carbon electrode

The electrochemical behavior of the anti-thalassemia and anti-HIV replication drug, deferiprone, was investigated on a carbon nanotube-modified glassy carbon (GC-CNT) electrode in phosphate buffer solution, pH 7.40 (PBS). During oxidation of deferiprone, two irreversible anodic peaks, with and , appeared, using GC-CNT. Cyclic voltammetric study indicated that the oxidation process is irreversible and diffusion controlled. The number of exchanged electrons in the electro-oxidation process was obtained, and the data indicated that deferiprone is oxidized via two two-electron steps. The results revealed that carbon nanotube (CNT) promotes the rate of oxidation by increasing the peak current, so that deferiprone is oxidized at lower potentials, which thermodynamically is more favorable. This result was confirmed by impedance measurements. The diffusion coefficient, electron-transfer coefficient and heterogeneous electron-transfer rate constant of deferiprone were found to be 1.49 × 10⁻⁶ cm² s⁻¹, 0.44, and 3.83 × 10⁻³ cm s⁻¹, respectively. A sensitive, simple and time-saving differential-pulse voltammetric procedure was developed for the analysis of deferiprone. Using the proposed method, deferiprone can be determined with a detection limit of 5.25 × 10⁻⁷ M. The applicability of the method to direct assays of spiked human serum and urine fluids is described.     

Copper chloride modified copper electrode: Application to electrocatalytic oxidation of methanol

Copper chloride modified copper (CCMC) electrode was prepared as a new electrode. For the preparation of the modified electrode, the polished copper electrode was placed in 0.1 M CuCl₂ solution for 20 s. In this step, a layer of copper (I) chloride was formed at the surface of copper electrode. Then, the electrode was placed in 0.1 M NaOH and the electrode potential was cycled between −250 and 1000 mV (vs. SCE) at a scan rate of 50 mV s⁻¹ for 5 cycles in a cyclic voltammetry regime until a featureless voltammogram was obtained. Surface physical characteristics of the modified electrode were studied by scanning electron micrographs (SEM). Results showed that considerable amounts of microcrystals have been formed on the copper surface during the modification. Surface elemental analysis of electrode were performed by energy dispersive X-ray (EDX) technique. The results showed that in addition to copper and chloride elements, there is also oxygen at the surface of CCMC electrode. This indicates that a layer of (ClCu)₂O was formed at the surface of the modified electrode. The electrocatalytic activity of the modified electrode for the oxidation of methanol, in aqueous basic solution was studied by using cyclic voltammetry. Results showed that, copper chloride modified electrode can improve the activity of Cu towards the oxidation of this small organic molecule, showing the possibility of attaining good electrocatalytic anodes for fuel cells. The modified electrode shows a stable and linear response in the concentration range of 5 × 10⁻³ to 8 × 10⁻² M with a correlation coefficient of 0.9958.     

Electrocatalytic reduction of oxygen at glassy carbon electrode modified by polypyrrole/anthraquinones composite film in various pH media

The electrocatalytic reduction of dioxygen by one mono and four dihydroxy derivatives of 9,10-anthraquinone (AQ) incorporated in polypyrrole (PPy) matrix on glassy carbon electrode has been investigated. The electrochemical behaviour of the modified electrodes was examined in various pH media and both the formal potential of anthraquinones and reduction potential of dioxygen exhibited pH dependence. AQ and PPy composite film showed excellent electrocatalytic performance for the reduction of O₂ to H₂O₂. pH 6.0 was chosen as the most suitable medium to study the electrocatalysis by comparing the peak potential of oxygen reduction and enhancement in peak current for oxygen reduction. The diffusion coefficient values of AQ at the modified electrodes and the number of electrons involved in AQ reduction were evaluated by chronoamperometric and chronocoulometric techniques, respectively. In addition, hydrodynamic voltammetric studies showed the involvement of two electrons in O₂ reduction. The mass specific activity of AQ used, the diffusion coefficient of oxygen and the heterogeneous rate constants for the oxygen reduction at the surface of modified electrodes were also determined by rotating disk voltammetry.     

铂纳米空球修饰玻碳电极对甲醛的电催化氧化行为

以纳米硒球为模板,H₂PtCl₆为前驱体,以抗环血酸为还原剂,SDSN作稳定剂,在室温下批量制备了铂纳米空球(Pt_Hollow)及其修饰玻碳(GC)电极(Pt_Hollow/GC)。使用XRD、SEM和TEM等检测技术表征了其形貌与结构,结果表明,所制备的铂纳米空球分散性好,粒径比较均匀,约为120 nm;球壳多孔,壳厚<10 nm,由多维、多级的多晶铂原子团簇所构建。以甲醛为探针分子,采用循环伏安及计时电流等常规电化学方法比较了电活性面积基本一致的Pt_Hollow/GC和电沉积铂纳米粒子(Pt_nano)修饰GC电极(Pt_nano/GC)催化甲醛氧化的性能,结果显示,位于0.64 V处的氧化峰电流密度,前者是后者氧化峰电流密度的1.5倍;氧化电流密度为0.5 mA·cm^-2处的氧化电位,前者比后者负移了约30 mV。实验结果表明,与Pt_nano/GC电极相比,甲醛在Pt_Hollow/GC电极上氧化的活化能低,反应速度快,催化活性高。所得结果为直接甲醛燃料电池阳极催化剂的研制提供了一定的实验与理论依据。     

Electrocatalytic oxidation of thioglycolic acid at carbon paste electrode modified with cobalt phthalocyanine: application as a potentiometric sensor

The voltammetric behavior of thioglycolic acid (TGA) was studied at a carbon paste electrode modified with cobalt phthalocyanine (CoPc). The CoPc-modified electrode shows high electrocatalytic activity toward oxidation of TGA, lowering substantially the overpotential of anodic reaction. Results of the cyclic voltammetry show that TGA undergoes a two-step oxidation (each step with one electron) resulting the dimer of thiol. Enhancement of the rate of electron transfer results in a near-Nernstian behavior of modified electrode to the concentration of TGA and makes it as a suitable potentiometric sensor for the detection of this compound. This electrode shows a near-Nernstian response in a wide linear range of the concentration TGA (4 orders of magnitude). The modified electrode was used successfully for the determination of TGA and its salts in hair-treatment products and also in culture media. The modified electrode exhibited a fast response time (<10 s), very good stability, and had an extended lifetime.