Electrochemical reduction of oxygen on thin-film Pt electrodes in acid solutions

The electrochemical reduction of oxygen on thin-film platinum electrodes in 0.1 M HClO₄ and 0.05 M H₂SO₄ solutions has been investigated using the rotating disk electrode (RDE) method. Thin films of Pt (0.25-20 nm thick) were prepared by vacuum evaporation onto glassy carbon substrate. The surface morphology of Pt films was examined by transmission electron microscopy (TEM). The specific activity of O₂ reduction was higher in HClO₄ and decreased with decreasing film thickness. In H₂SO₄, the specific activity was lower and appeared to be independent of the Pt loading. The values of Tafel slopes close to −120 mV dec⁻¹ in high current density range and −60 mV dec⁻¹ in low current density range were obtained for all electrodes in both solutions, indicating that the mechanism of O₂ reduction is the same for thin-film electrodes as for bulk Pt. The number of electrons transferred per O₂ molecule was close to four for all thin Pt films studied.     

In situ radiotracer and voltammetric study of the formation of surface adlayers in the course of Cr(VI) reduction on polycrystalline and (1 1 1) oriented platinum

This paper is focused on the in situ radiotracer and voltammetric studies of the induced HSO₄⁻/SO₄²⁻ adsorption at Pt(poly) and Pt(1 1 1) surfaces in 0.1 mol dm⁻³ HClO₄ solution in the course of Cr(VI) electroreduction. Besides this, the sorption behavior of HSO₄⁻/SO₄²⁻ ions on bare Pt(poly) and Pt(1 1 1) electrodes is compared and discussed. From the experimental results it can be stated that: (i) although the extent of bisulfate/sulfate adsorption is strongly dependent upon the crystallographic orientation of Pt surfaces, the maximum coverage on the Pt(1 1 1) does not exceed 0.2 monolayer; (ii) the Cr(VI) electroreduction on both poly- and (1 1 1) oriented platinum proceeds via a ce (chemical-electron-transfer) mechanism to yield Pt surfaces covered with intermediate surface adlayers containing Cr(VI) particles (and reduced Cr-containing adspecies) and ‘strongly bonded’ HSO₄⁻/SO₄²⁻ ions; (iii) while the coverage of platinum surfaces by the intermediate complexes formed in the course of Cr(VI) electroreduction at E > 0.20 V is basically independent of the crystallographic orientation of the Pt electrode, the onset for rapid Cr(VI) reduction is highly affected by the nature and crystallographic orientation of the electrode.     

Enhanced mass transport to a reticulated vitreous carbon rotating cylinder electrode using jet flow

The mass transport characteristics of a porous, rotating cylinder electrode (RCE, 1.0 cm diameter; 0.5, 0.9 or 1.2 cm long; 1.25, 2.25, 3.00 cm³ overall volume; 250-2000 rpm speed) fabricated from reticulated vitreous carbon (RVC, 60 ppi or 100 ppi) were investigated. The deposition of copper from an acid sulfate electrolyte (typically, deoxygenated 1 mM CuSO₄ in pH 2, 0.5 M Na₂SO₄ at 298 K) was used as a test reaction. The effect of a jet flow of electrolyte towards the electrode and the introduction of polypropylene baffles in the electrochemical cell were studied at controlled rotation rates of the RCE. The product of mass transport coefficient and volumetric electrode area (k_mA_e) is related to the rotation speed of the electrode. For the 60 ppi RVC RCE, the jet electrolyte flow (3.5 cm³ s⁻¹) enhanced the mass transport rates by a factor of 1.46 at low rotation speeds; this factor was reduced to 1.08 at high rotation speeds. For a 100 ppi electrode, the enhanced mass transport decreased from 1.26 to 1.03 at low and high rotation rates, respectively. Under the experimental conditions, baffles showed little effect on the mass transport rates to the RVC RCE. Mass transport to jet flow at an RVC RCE is compared to other RCEs using dimensionless group correlation.     

Synthesis of Pt nanocatalyst with micelle-encapsulated multi-walled carbon nanotubes as support for proton exchange membrane fuel cells

Micelle-encapsulated multi-walled carbon nanotubes (MWCNTs) with sodium dodecyl sulfate (SDS) were used as catalyst support to deposit platinum nanoparticles. High resolution transmission electron microscopy (HRTEM) images reveal the crystalline nature of Pt nanoparticles with a diameter of ∼4 nm on the surface of MWCNTs. A single proton exchange membrane fuel cell (PEMFC) with total catalyst loading of 0.2 mg Pt cm⁻² (anode 0.1 and cathode 0.1 mg Pt cm⁻², respectively) has been evaluated at 80 °C with H₂ and O₂ gases using Nafion-212 electrolyte. Pt/MWCNTs synthesized by using modified SDS-MWCNTs with high temperature treatment (250 °C) showed a peak power density of 950 mW cm⁻². Accelerated durability evaluation was carried out by conducting 1500 potential cycles between 0.1 and 1.2 V with 50 mV s⁻¹ scan rate, H₂/N₂ at 80 °C. The membrane electrode assembly (MEA) with Pt/MWCNTs showed superior performance stability with a power density degradation of only ∼30% compared to commercial Pt/C (70%) after potential cycles.     

Electrochemical degradation of Ibuprofen on Ti/Pt/PbO2 and Si/BDD electrodes

The electrochemical oxidation of Ibuprofen (Ibu) was performed using a Ti/Pt/PbO₂ electrode as the anode, prepared according to literature, and a boron doped diamond (BDD) electrode, commercially available at Adamant Technologies. Tests were performed with model solutions of Ibu, with concentrations ranging from 0.22 to 1.75 mM for the Ti/Pt/PbO₂ electrode and 1.75 mM for the BDD electrode, using 0.035 M Na₂SO₄ as the electrolyte, in a batch cell, at different current densities (10, 20 and 30 mA cm⁻²). Absorbance measurements, Chemical Oxygen Demand (COD) and Total Organic Carbon (TOC) tests were conducted for all samples. The results have shown a very good degradation of Ibu, with COD removals between 60 and 95% and TOC removals varying from 48 to 92%, in 6 h experiments, with higher values obtained with the BDD electrode. General Current Efficiency and Mineralization Current Efficiency, determined for both electrodes, show a similar behaviour for 20 mA cm⁻² but a very different one at 30 mA cm⁻². The combustion efficiency was also determined for both anodes, and found to be slightly higher with BDD at lower current density and equal to 100% for both anodes at 30 mA cm⁻².     

Carbon-coated tungsten and molybdenum carbides for electrode of electrochemical capacitor

New electrode materials for electrochemical capacitor, tungsten carbide WC and molybdenum carbide Mo₂C coated by porous carbon, were prepared through a simple heat treatment of the mixture of K₂WO₄ and K₂MoO₄, respectively, with hydroxy propyl cellulose. Carbide changed to hydroxide during the 1st charge-discharge cycle in H₂SO₄ aqueous electrolyte, which showed redox reaction in further charge-discharge cycles, in addition to electric double layers of the carbon formed on its surface. The carbon-coated carbide gave a high capacitance in 1 mol L⁻¹ H₂SO₄ electrolyte, as about 350 F cm⁻³ for carbon-coated WC and 550-750 F cm⁻³ for carbon-coated Mo₂C. Coating of carbon inhibits the growth of carbide particles during their formation, of which the small particle size make possible to complete transformation to hydroxides during the 1st charge-discharge cycle, and also disturbs the agglomeration of tungsten and molybdenum hydroxides during charge-discharge cycles, as well as porous carbon coated act as electrode material for electric double layers of electrolyte ions.     

Electroreduction of oxygen on gold-supported nanostructured palladium films in acid solutions

The electrochemical reduction of oxygen on thin Pd films with a nominal thickness of 0.25-10 nm on polycrystalline Au substrate (Pd/Au) was studied. The Pd films were prepared by electron beam evaporation and oxygen reduction was studied in 0.1 M HClO₄ and 0.05 M H₂SO₄ solutions using the rotating disk electrode (RDE) method. The surface morphology of Pd overlayers was examined by scanning tunnelling microscopy (STM). O₂ reduction predominantly proceeds through 4e⁻ pathway on all Pd/Au electrodes. The specific activity (SA) of oxygen reduction was lower in H₂SO₄ solution and decreased slightly with decreasing the Pd film thickness. In HClO₄, the SA was higher and not significantly dependent on the film thickness. The Tafel slope values close to −60 mV at low current densities and −120 mV at high current densities were found for all electrodes.     

Electropolymerization of aniline in acid media on the bare and chemically pre-treated aluminum electrodes: A comparative characterization of the polyaniline deposited electrodes

The electrosynthesis of polyaniline on the bare aluminum and pre-treated aluminum surface achieved in aqueous H₂PtCl₆ solution saturated with NaF for few seconds is described. The effect of some factors such as pre-treatment time, aniline and sulfuric acid concentrations on the electropolymerization process was investigated and optimum conditions were obtained. The stability of polyaniline film on the pre-treated aluminum electrode (Al-Pt) was studied as function of the potential imposed on the electrode. For applied electrode potentials of 0.1-0.7 V, the first-order degradation rate constant, k, of polyaniline film varies between 1 × 10⁻⁶ and 2 × 10⁻⁵ s⁻¹, and a relatively low slope (i.e. 2.1) was obtained for the plot of log k versus E. The coatings were characterized by scanning electron microscopy (SEM), and cyclic voltammetric behavior of the polyaniline-deposited Al electrode (Al/PANI) and polyaniline-deposited Al-Pt electrode (Al-Pt/PANI) in 0.1 H₂SO₄ solutions is described. The electrocatalytic activity of the Al-Pt/PANI electrode against para-benzoquinone/hydroquinone (Q/H₂Q) and Fe(CN)₆³⁻/Fe(CN)₆⁴⁻ redox systems was investigated and the obtained results are compared with those obtained on Al/PANI and bulk Pt electrodes.     

The electrochemical synthesis of polyaniline/polysulfone composite films and electrocatalytic activity for ascorbic acid oxidation

Polyaniline (PANI)/polysulfone (PSF) composite films with asymmetric porous structure were successfully prepared by electropolymerization. The back face (in contact with the electrode) of the freestanding composite film is green while the outer face is white. The chemical component and the morphology of the surfaces were characterized by FTIR spectra and scanning electron microscopy, respectively. It was shown that replicate films gave reproducible voltammetry in 0.5 M H₂SO₄. The influence of the electrolyte and the acidic concentration on the redox peak currents of polyaniline were investigated in detail. The composite film electrode showed good electrocatalytic activity for ascorbic acid, which the anodic overpotential was evidently reduced compared with that obtained at bare Pt electrode. The diffusion coefficient of ascorbic acid was 1.38 × 10⁻⁶ cm² s⁻¹.     

Influence of Nafion film on oxygen reduction reaction and hydrogen peroxide formation on Pt electrode for proton exchange membrane fuel cell

The influence of Nafion^® film on ORR kinetics and H₂O₂ formation on a Pt electrode was investigated using RRDE in 0.1 M HClO₄. It was found that the Nafion^®-coated Pt system showed lower apparent ORR activity and more H₂O₂ production than the bare Pt electrode system. From the temperature sensitivity, it was revealed that the apparent activation energies of ORR in the Nafion^®-coated Pt system were lower than the bare Pt electrode system, and the H₂O₂ formation was suppressed with the increase of the temperature. In order to analyze the results furthermore, other systems (0.1/1.0 M, HClO₄/CF₃SO₃H) with the bare Pt electrodes were also examined as references. It was exhibited that the ORR kinetic current, the H₂O₂ formation, and the apparent activation energies of 1.0 M CF₃SO₃H system were close to those of the Nafion^®-coated Pt system. We concluded that the orientation of anion species of Nafion^® and CF₃SO₃H to the Pt surface via water molecules, as well as a fluorocarbon polymer network of Nafion^®, might block O₂ adsorption, resulting in the smaller effective surface area of the Pt electrode for ORR, the smaller ORR kinetic current, and the more H₂O₂ production.     

Kinetics and mechanism of oxygen reduction at hydrous oxide film-covered platinum electrode in alkaline solution

This study uses rotating ring-disk electrode (RRDE) and linear sweep voltammetry (LSV) to characterize oxygen reduction kinetics in alkaline solution on platinum electrodes with various thickness of hydrous oxide (oxyhydroxy) film. Oxyhydroxy films are created on Pt electrodes by pretreatment in 1.0 mol dm⁻³ KOH at a constant voltage. The pretreatment voltage ranges from −1.2 to 1.0 V and is increased stepwise before each new experimental run to produce seven discreet films. LSV plots show oxyhydroxy film thickness strongly inhibits oxygen reduction and is inversely proportional to RRDE oxygen reduction current I_D for LSV voltages E_D from −0.1 to −0.46 V, but this trend reverses at E_D more negative than −0.46 V so that the worst-performing electrode becomes the best. However, this improvement disappears at around −0.8 V, suggesting this change involves a negatively charged ion, possibly embedded into the metal in the top few atomic layers either interstitially or substitutionally. The 1.0 V-pretreated electrode in the E_D range from −0.46 to −0.9 V of highest oxygen reduction current also exhibits the lowest hydrogen peroxide production, with zero H₂O₂ produced at −0.6 V, indicating the brief presence of the oxyhydroxy film on the Pt surface has strong lingering effects. The post-oxyhydroxy Pt surface is very different than the native Pt for oxygen reduction pathway and efficiency. Reaction order with respect to oxygen is close to 1. The rate constants of the direct O₂ to H₂O electroreduction reaction are increased with decreasing the potential from −0.2 to −0.6 V, but the O₂ to H₂O₂ electroreduction is contrary to this expectation. The rate constants of H₂O₂ decomposition on the oxyhydroxy film-covered Pt electrode are near constant around 1 × 10⁻⁴ cm s⁻¹ at E_D > −0.5 V.     

Electrochemical copolymerization of aniline with m-aminophenol and novel electrical properties of the copolymer in the wide pH range

A copolymer, poly(aniline-co-m-aminophenol), has been synthesized using repeated potential cycling. The monomer concentration ratio, acid concentration and applied potential strongly affect the copolymerization rate and the properties of the copolymer. The optimum conditions for the copolymerization are that the scan potential range is controlled between −0.10 and 0.95 V (vs.SCE), and a solution consists of 0.34 M aniline, 0.012 M m-aminophenol and 2 M H₂SO₄. The IR spectra of the copolymers demonstrate that the m-aminophenol units are included in the copolymer chains. The cyclic voltammograms of the copolymers in 0.3 M Na₂SO₄ solution with various pH values were performed at the potential ranges from −0.20 to 0.80 V and at a scan rate of 60 mV s⁻¹. The results indicate that the copolymer still hold 41.7% of the electrochemical activity when the copolymer electrode was transferred from a solution of pH 5.0 to a solution of pH 11.0 in the potential range of −0.20 to 0.80 V. An impedance plot of the copolymer in a solution with pH 12.0 and at 0.40 V is constructed of a semicircle and a Warburg line with a slope of 1. This means that the electrode reaction of the copolymer at pH 12.0 is also under mass transfer control. The conductivity of the copolymer prepared under the optimum conditions is 1.42 S cm⁻¹, and slightly depends on the pH value. Thus, the pH dependence of the electrical properties of the copolymer is improved compared with poly(aniline-co-o-aminophenol), and is much better than that of the parent polyaniline.     

Anodically formed oxide films and oxygen reduction on electrodeposited ruthenium in acid solution

The impedance of the anodically formed hydrous Ru oxide in the system Ru|oxide film|1 M HClO₄ solution has been studied in the range of potentials where the electrode process occurs by a double electron and proton exchange between the oxide film and the solution. The results allowed us to clearly distinguish between the surface process at higher frequency and the bulk process at lower frequency. The high-frequency charging is found to be coupled to Faradaic charging at the film/solution interface. Evaluation of the impedance data at lower frequency, using diffusion equations for the finite boundary conditions, yields an effective proton diffusion coefficient to be 10⁻¹⁰ to 10⁻¹¹ cm² s⁻¹.Oxygen reduction on the spontaneously oxidized ruthenium electrode was discussed on the basis of a rotating ring-disk voltammetry.     

Surface-enhanced IR spectroscopy investigation on the electro-oxidation of CO adlayer at a polycrystalline Pt film electrode in Cl-containing HClO4

The electro-oxidation of CO adlayer on Pt electrode in Cl⁻-containing 0.1 M HClO₄ has been investigated with in situ attenuated-total-reflection surface-enhanced infrared absorption spectroscopy (ATR-SEIRAS). Two potentials were selected for predosing CO on the Pt electrode: one is in the H-UPD region, i.e., 0.1 V (vs. RHE) and the other is in the double-layer region, i.e., 0.45 V (vs. RHE). The broadening of the prewave and the main peak for the CO oxidation is observed, in addition to the positively shifted oxidation potentials. The spectroelectrochemical data suggest the specific adsorption of Cl⁻ starts at a potential as negative as 0.1 V which may compete with the adsorption of OH at CO-unoccupied sites (including but not limited to defect sites) and/or hinder the diffusion of CO to OH adsorption sites on Pt electrode, slowing down the CO oxidation. This competitive Cl⁻ adsorption at lower potentials disrupts the interfacial free H₂O structure on the top of CO adlayer, signaled by a reduced OH stretching band intensity.     

High capacitance properties of polyaniline by electrochemical deposition on a porous carbon substrate

Electrochemical deposition of polyaniline (PANI) is carried out on a porous carbon substrate for supercapacitor studies. The effect of substrate is studied by comparing the results obtained using platinum, stainless steel and porous carbon substrates. PANI deposited at 100 mV s⁻¹ sweep rate by potentiodynamic technique on porous carbon substrate is found to possess superior capacitance properties. Experimental variables, namely, concentrations of aniline monomer and H₂SO₄ supporting electrolyte are varied and arrived at the optimum concentrations to obtain a maximum capacitance of PANI. Low concentrations of both aniline and H₂SO₄, which produce PANI at low rates, are desirable. The PANI deposits prepared under these conditions possess network morphology of nanofibrils. Capacitance values as high as 1600 F g⁻¹ are obtained and PANI coated carbon electrodes facilitate charge-discharge current densities as high as 45 mA cm⁻² (19.8 A g⁻¹). Electrodes are found to be fairly stable over a long cycle-life, although there is some capacitance loss during the initial stages of cycling.     

Synthesis and electrical properties of the (PVA)0.7(KI)0.3·xH2SO4 (0 ≤ x ≤ 5) polymer electrolytes and their performance in a primary Zn/MnO2 battery

Solid acid polymer electrolytes (SAPE) were synthesised using polyvinyl alcohol, potassium iodide and sulphuric acid in different molar ratios by solution cast technique. The temperature dependent nature of electrical conductivity and the impedance of the polymer electrolytes were determined along with the associated activation energy. The electrical conductivity at room temperature was found to be strongly depended on the amorphous nature of the polymers and H₂SO₄ concentration. The ac (100 Hz to 10 MHz) and dc conductivities of the polymer electrolytes with different H₂SO₄ concentrations were analyzed. A maximum dc conductivity of 1.05 × 10⁻³ S cm⁻¹ has been achieved at ambient temperature for electrolytes containing 5 M H₂SO₄. The frequency and temperature dependent dielectric and electrical modulus properties of the SAPE were studied. The charge transport in the present polymer electrolyte was obtained using Wagner's polarization technique, which demonstrated the charge transport to be mainly due to ions. Using these solid acid polymer electrolytes novel Zn/SAPE/MnO₂ solid state batteries were fabricated and their discharge capacity was calculated. An open circuit voltage of 1.758 V was obtained for 5 M H₂SO₄ based Zn/SAPE/MnO₂ battery.     

Supercapacitive properties of a nanowire-structured MnO2 electrode in the gel electrolyte containing silica

Nanowire-structured MnO₂ active materials were prepared by a chemical precipitation method and their supercapacitive properties for use in the electrodes of supercapacitors were investigated by means of cyclic voltammetry in an aqueous gel electrolytes consisting of 1 M Na₂SO₄ and fumed silica (SiO₂). The MnO₂ electrode showed a maximum specific capacitance of 151 F g⁻¹ after 1000 cycles at 100 mV s⁻¹ when using the gel electrolyte containing 3 wt.% of SiO₂, which is higher than 121 F g⁻¹ obtained when using the 1 M Na₂SO₄ liquid electrolyte alone.     

Enhancement of oxygen reduction by incorporation of heteropolytungstate into the electrocatalytic ink of carbon supported platinum nanoparticles

Nafion stabilized inks of Vulcan XC-72 supported platinum (20 wt.%) nanoparticles (Pt/XC-72) were utilized to produce electrocatalytic films on glassy carbon. The catalysts were modified (activated) with phosphododecatungstic acid H₃PW₁₂O₄₀ (PW₁₂). Comparison was made to bare (PW₁₂-free) electrocatalytic films. Electroreduction of dioxygen was studied at 25 °C in 0.5 mol dm⁻³ H₂SO₄ electrolyte using rotating disk voltammetry. For the same loading of platinum (≈95 μg cm⁻²) and for the approximately identical distribution of the catalyst, the reduction of oxygen at a glassy carbon electrode modified with the ink containing PW₁₂ proceeded at ca. 30-60 mV more positive potential (depending on the PW₁₂ content), and the system was characterized by a higher kinetic parameter (rate of heterogeneous electron transfer), when compared to the PW₁₂-free electrocatalyst. Gas diffusion electrodes with Pt/XC-72 supported on carbon paper (Pt loading 1 mg cm⁻²) were also tested. Under the same experimental conditions, while the exchange current density and the total resistance contribution to polarization components, computed from the galvanostatic polarization curves were found to be clearly higher and lower, respectively, for the ink modified with PW₁₂ relative to the unmodified system. The results demonstrate that addition of heteropolytungstatic acid (together with Nafion) enhances the electrocatalytic activity of platinum towards reduction of oxygen.     

Finely dispersed Pt nanoparticles in conducting poly(o-anisidine) nanofibrillar matrix as electrocatalytic material

A new approach based on stepwise oxidation of o-anisidine is explored for generating nanoporous films of poly(o-anisidine), POA and loading of Pt nanoparticles that are subsequently used for electrocatalysis of methanol oxidation are presented and compared with bulk Pt. POA film can easily be prepared by stepwise electro-oxidation procedure with very high porosity consisting of nanofibrillar structure using without templates. Controlled sizes of Pt nanoparticles were entrapped into POA matrix by a two-step process in which first PtCl₆²⁻ ions are sorbed into the pores of polymer matrix followed by electroreduction at −0.55 V in a 0.5 M H₂SO₄ solution. Loading of Pt nanoparticles (10-200 μg/cm²) onto POA matrix were accomplished by varying the concentration (2-10 mM) of the sorbate, i.e., H₂PtCl₆. The sizes of the Pt nanoparticles were determined from TEM analysis and Pt particles were found to be in the range of 10-20 nm. The crystallite phase of Pt particles in POA was examined from XRD pattern. AFM image further supports Pt particles embedded in POA matrix.     

Spray deposited titanium oxide thin films as passive counter electrodes

Titanium dioxide (TiO₂) thin films were deposited from methanolic solution onto fluorine doped tin oxide coated conducting glass substrates by spray pyrolysis technique. The electrochemical properties of TiO₂ thin films were investigated using cyclic voltammetry, chronoamperometry, chronocoulometry and iono-optical studies, in 0.1N H₂SO₄ electrolyte. Performance of the films deposited at three different substrate temperatures, viz. 350, 400 and 450 °C is discussed in view of their utilization in electrochromic devices, as counter electrode. The magnitude of charge storage capacity, Q/t (4.75-6.13 × 10⁻³ mC/(cm² nm)) and colouration efficiency (3.2-4.3 cm²/mC) of TiO₂ rank these films among the promising counter electrodes in electrochromic devices.