Investigation of the Effects of Injection Molding Processing Parameters on Conductive Polymeric Composites for Electromagnetic Interference Shielding Effectiveness

Polycarbonate (PC) composites filled with conductive nickel-coated carbon fibers (NCFs) were injection-molded under different injection process conditions. They were then used to investigate the influence of the injection processing parameters of melt temperature, mold temperature, injection velocity and packing pressure on the electromagnetic interference (EMI) shielding effectiveness (SE). In order to study the effect of the molding variables using the minimum number of experiments, the Taguchi method was employed. The aim of the Taguchi method was to optimize the injection processing parameters for better EMI shielding of the conductive polycarbonate composites. It is found out that the packing pressure and mold temperature affect the EMI shielding efficiency most significantly.     

Effects of molding conditions on the electromagnetic interference performance of conductive ABS parts

Polymers filled with conducting fibers to prevent electromagnetic interference (EMI) performance have recently received great attention due to the requirements of 3C (computer, communication, and consumer electronics) products. In the present article, the effect of fiber content and processing parameters, including melt temperature, mold temperature, and injection velocity, on the electromagnetic interference shielding effectiveness (SE) in injection molded ABS polymer composites filled with conductive stainless steel fiber (SSF) was investigated. The influence of fiber orientation and distribution resulting from fiber content and molding conditions on EMI performance was also examined. It was found from measured results that fiber content plays a significant role in influencing part EMI SE performance. SE value can reach the highest values of approximately 40 dB and 60 dB at 1000 MHz frequency for fiber content 7 wt % and 14 wt %, respectively, under the best choice of molding conditions. Higher melt and mold temperature would increase shielding effectiveness due to a more uniform and random fiber orientation. However, higher injection velocity leading to highly‐orientated and less uniform distribution of fiber reduces shielding effectiveness. Among all molding parameters, melt temperature affects SE performance most significantly. Its influence slightly decreases as fiber content increases. Injection speed plays a secondary importance in affecting SE values, and its influence increases as fiber content increases. Upon examination of fiber distribution via optical microscope and subsequent image analysis, it was found that the fiber becomes more densely and random distributed toward the last melt‐filled region, whereas fiber exhibits less concentration around the middle way of the flow path. This can be attributed to the combined effects of fountain flow, frozen layer thickness, and gapwise melt front velocity. The results indicate that molding conditions, instead of fiber content alone, are very important on the SE performance for injection molded SSF filled ABS composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1072–1080, 2005     

Comparative study of electromagnetic interference shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene composites

This study compares electromagnetic interference (EMI) shielding properties of injection molded versus compression molded multi-walled carbon nanotube/polystyrene (MWCNT/PS) composites, i.e., properties such as EMI shielding effectiveness (EMI SE), electrical conductivity, real permittivity and imaginary permittivity. The injection molded (MWCNT-aligned) samples showed lower EMI shielding properties than compression molded (randomly distributed MWCNT) samples that was attributed to lower probability of MWCNTs contacting each other due to MWCNT alignment. The compression molded samples showed higher electrical conductivity and lower electrical percolation threshold than the injection molded samples. The compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% showed real permittivity two times and imaginary permittivity five times greater than the injection molded samples. The EMI SE for the compression molded samples at MWCNT concentrations of 5.00 and 20.0 wt.% was 15.0 and 30.0 dB, respectively, significantly greater than EMI SE for the injection molded samples. Lower EMI SE for the injection molded samples was ascribed to lower electrical conductivity, real permittivity (polarization loss) and imaginary permittivity (Ohmic loss). Comparison of the EMI shielding properties of the compression molded versus injection molded samples confirmed that EMI shielding does not require filler connectivity; however it increases with filler connectivity.     

Synergistic effect of multiwalled carbon nanotubes and an intumescent flame retardant: Toward an ideal electromagnetic interference shielding material with excellent flame retardancy

To shield undesirable electromagnetic waves caused by electronic devices and simultaneously resolve the flame safety of the electronic components, an electromagnetic interference (EMI) shielding material with excellent flame‐retardant properties is urgently needed. The synergistic effect of the intumescent flame retardant (IFR) and multiwalled carbon nanotubes (MWCNTs) for polystyrene (PS) nanocomposites prepared by melt blending was investigated. The results show that addition of certain amounts of IFRs facilitated the dispersion of MWCNTs in the PS matrix, and the percolation threshold of the MWCNTs in the PS matrix also decreased from 1.67 ± 0.05 to 1.29 ± 0.04 wt %. Moreover, the EMI shielding efficiencies (SEs) of the PS–MWCNT–IFR composites were consistently higher than those of the PS–MWCNT composites without the addition of the IFRs at the same MWCNT content; this indicated that the synergistic effect of the MWCNTs and IFRs effectively improved the EMI SE of the PS–MWCNT–IFR composites. Furthermore, the limiting oxygen index (LOI) testing results show that the LOI values of the PS–MWCNT composites were consistently higher than 27%; this indicated that the PS–MWCNT composites effectively met the needs of flame safety; this indicated that the PS–MWCNT–IFR composite is a novel and promising candidate for an ideal EMI shielding material with excellent flame‐retardant properties for today's electronic devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45088.     

Thermoplastic polyvinyl alcohol/multiwalled carbon nanotube composites: Preparation,mechanical properties,thermal properties,and electromagnetic shielding effectiveness

This study uses the solution mixing method to combine plasticized polyvinyl alcohol (PVA) as a matrix, and multiwalled carbon nanotubes (MWCNTs) as reinforcement to form PVA/MWCNTs films. The films are then laminated and hot pressed to create PVA/MWCNTs composites. The control group of PVA/MWCNTs composites is made by incorporating the melt compounding method. Diverse properties of PVA/MWCNTs composites are then evaluated. For the experimental group, the incorporation of MWCNTs improves the glass transition temperature (T_g), crystallization temperature, T_c), and thermal stability of the composites. In addition, the test results indicate that composites containing 1.5 wt % of MWCNTs have the maximum tensile strength of 51.1 MPa, whereas composites containing 2 wt % MWCNTs have the optimal electrical conductivity of 2.4 S/cm, and electromagnetic shielding effectiveness (EMI SE) of ?31.41 dB. This study proves that the solution mixing method outperforms the melt compounding method in terms of mechanical properties, dispersion, melting and crystallization behaviors, thermal stability, and EMI SE. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43474.     

Graphene nanoplate and multiwall carbon nanotube–embedded polycarbonate hybrid composites: High electromagnetic interference shielding with low percolation threshold

This study has reported the preparation of polycarbonate (PC)/graphene nanoplate (GNP)/multiwall carbon nanotube (MWCNT) hybrid composite by simple melt mixing method of PC with GNP and MWCNT at 330°C above the processing temperature of the PC (processing temperature is 280°C) followed by compression molding. Through optimizing the ratio of (GNP/MWCNT) in the composites, high electromagnetic interference shielding effectiveness (EMI SE) value (∼21.6 dB) was achieved at low (4 wt%) loading of (GNP/MWCNT) and electrical conductivity of ≈6.84 × 10⁻⁵ S.cm⁻¹ was achieved at 0.3 wt% (GNP/MWCNT) loading with low percolation threshold (≈0.072 wt%). The high temperature melt mixing of PC with nanofillers lowers the melt viscosity of the PC that has helped for better dispersion of the GNPs and MWCNTs in the PC matrix and plays a key factor for achieving high EMI shielding value and high electrical conductivity with low percolation threshold than ever reported in PC/MWCNT or PC/graphene composites. With this method, the formation of continuous conducting interconnected GNP‐CNT‐GNP or CNT‐GNP‐CNT network structure in the matrix polymer and strong π–π interaction between the electron rich phenyl rings and oxygen atom of PC chain, GNP, and MWCNT could be possible throughout the composites. POLYM. COMPOS., 37:2058–2069, 2016. © 2015 Society of Plastics Engineers     

Electrical,rheological and electromagnetic interference shielding properties of thermoplastic polyurethane/carbon nanotube composites

Electrically conducting rubbery composites based on thermoplastic polyurethane (TPU) and carbon nanotubes (CNTs) were prepared through melt blending using a torque rheometer equipped with a mixing chamber. The electrical conductivity, morphology, rheological properties and electromagnetic interference shielding effectiveness (EMI SE) of the TPU/CNT composites were evaluated and also compared with those of carbon black (CB)‐filled TPU composites prepared under the same processing conditions. For both polymer systems, the insulator–conductor transition was very sharp and the electrical percolation threshold at room temperature was at CNT and CB contents of about 1.0 and 1.7 wt%, respectively. The EMI SE over the X‐band frequency range (8–12 GHz) for TPU/CNT and TPU/CB composites was investigated as a function of filler content. EMI SE and electrical conductivity increased with increasing amount of conductive filler, due to the formation of conductive pathways in the TPU matrix. TPU/CNT composites displayed higher electrical conductivity and EMI SE than TPU/CB composites with similar conductive filler content. EMI SE values found for TPU/CNT and TPU/CB composites containing 10 and 15 wt% conductive fillers, respectively, were in the range ?22 to ?20 dB, indicating that these composites are promising candidates for shielding applications. © 2013 Society of Chemical Industry     

Electrical and electromagnetic interference shielding properties of flow-induced oriented carbon nanotubes in polycarbonate

The electrical and electromagnetic interference shielding effectiveness (EMI SE) properties of multi-walled carbon nanotubes/polycarbonate (MWCNT/PC) composites are investigated. The composites were prepared by diluting masterbatch (15 wt.% MWCNT) using a Haake mixer and then injection-molded into a dog-bone mold. Various MWCNT alignments were created by changing operating conditions. Electrical resistivity measurements were carried out at three different areas at both parallel and perpendicular to the flow direction. The results showed higher resistivity and percolation threshold at higher alignments in both parallel and perpendicular to the flow direction. By applying Ohm’s law it was seen that after percolation, the field emission mechanisms are more important at higher orientations. Higher MWCNT alignments were observed in areas with higher resistivities, and this was verified using SEM, TEM and Raman spectroscopy techniques. Additionally, EMI SE measurements were done on compression-molded samples at different concentrations and thicknesses. The results showed that both EMI SE by reflection and absorption increased with increase in MWCNT loading and shielding material thickness.     

Mild functionalization of carbon nanotubes filled epoxy composites: Effect on electromagnetic interferences shielding effectiveness

The effect of nitric acid mild functionalized multiwalled carbon nanotubes (MWCNTs) on electromagnetic interference (EMI) shielding effectiveness (SE) of epoxy composites was examined. MWCNTs were oxidized by concentrated nitric acid under reflux conditions, with different reaction times. The dispersion of MWCNTs after functionalization was improved due to the presence of oxygen functional groups on the nanotubes surface. Functionalization at 2 h exhibits the highest EMI SE and electrical conductivity of MWCNTs filled epoxy composites. However, EMI shielding performance of MWCNTs filled epoxy composite declined when the functionalization reaction time was prolonged. This was due to extensive damage on the MWCNT structure, as verified by a Raman spectroscope. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42557.     

多壁碳纳米管复合聚碳酸酯/苯乙烯系聚合物复合材料导电性能的研究

采用一步法将聚苯乙烯（PS）、苯乙烯-丙烯腈共聚物（SAN）和甲基丙烯酸甲酯-苯乙烯共聚物（MS）分别与聚碳酸酯（PC）、多壁碳纳米管（MWCNTs）熔融混合,得到PC/PS/MWCNTs、PC/SAN/MWCNTs和PC/MS/MWCNTs三种复合材料。透射电子显微镜和场发射扫描电子显微镜观察表明,MWCNTs选择性分散在PC相中,这与Sumita模型预测的结果完全吻合,且随着PS、SAN或MS含量的增加,体系的体积电阻率-苯乙烯系聚合物含量曲线能够很好地拟合到PC/MWCNTs体系的体积电阻率-MWCNTs有效体积浓度曲线上,体系的体积电阻率变化符合有效浓度的概念。     

Studies on processing parameters and thermal stability of ENCF/ABS composites for EMI shielding

Electroless nickel coated carbon fibers (ENCF) were blended with acrylonitrile-butadiene-styrene (ABS) to prepare composites for electromagnetic interference (EMI) shielding. The effects of processing parameters, such as additives, temperature, and fiber loading amount, on EMI shielding effectiveness (SE) were researched. The thermal stability of EMI SE of ENCF/ABS composites was tested by heat treating composites in a drying oven at 60°C, and SE was measured at an interval of one week to consider the degradation of SE. The best SE of ENCF/ABS composites could be reached was 44 dB at optimum processing parameters. The thermal stability of ENCF/ABS composites for EMI shielding was steady without obvious degradation after 60°C heat treatment for five weeks. © 1997 John Wiley & Sons, Inc.     

Effect of oxyfluorination on electromagnetic interference shielding of polypyrrole-coated multi-walled carbon nanotubes

The polypyrrole-coated multi-walled carbon nanotubes (MWCNTs) were prepared by in situ chemical oxidative polymerization of pyrrole on the surface of MWCNTs for the novel electromagnetic interference (EMI) shielding materials. The oxyfluorination treatment on MWCNTs introduced the hydrophilic functional groups resulting in well distribution and higher interfacial affinity between polypyrrole (PPy) and MWCNTs. The PPy phases formed on MWCNTs were observed by SEM. The thickness of PPy on the surface of MWCNTs decreased as increasing the hydrophilic groups on MWCNTs by the oxyfluorination treatment. The PPy-coated MWCNT composites showed the remarkable increases in permittivity, permeability, and EMI shielding efficiency (SE). The EMI SE of PPy-coated MWCNTs increased up about 28.6 dB mainly based on the absorption mechanism.     

A comparative study on the influences of whisker and conventional carbon nanotubes on the electrical and thermal conductivity of polyether ether ketone composites

In this study, the electrical and thermal conductivity of polyether ether ketone (PEEK)/carbon nanotubes (CNTs) with different types, namely whisker CNTs (Wh-CNTs) and conventional CNTs were compared. PEEK/CNTs composites were melt mixed in PEEK via two screw extrusion technology. Moreover, the effects of different methods for mixing of PEEK/Wh-CNTs, namely, dry mixing, wet mixing and melt mixing, were compared. The electrical and thermal properties were analyzed. A high thermal conductivity value of about 0.741 W/(m K) could be obtained upon loading with 10 wt% Wh-CNTs and the PEEK/Wh-CNTs composites had low volume resistivity value of 10.96 Ω cm at 10 wt% loading via melt mixing. Thermal conductivity values of 1.066 W/(m K) (out-of-plane) and 1.50 W/(m K) (in-plane) were achieved with 10 wt% loading by wet mixing. Experimental results of out-of-plane thermal conductivity were more consistent with the Nan model. PEEK/Wh-CNTs composites prepared by wet mixing exhibited higher thermal conductivity than the composites mixed using the two other methods. As the content of Wh-CNTs in wet mixed PEEK/Wh-CNTs nanocomposites increased, electromagnetic interference (EMI) shielding effectiveness (SE) was improved. The PEEK/Wh-CNTs composites were 0.6 mm thick and showed an EMI SE of 21.5 dB.     

Enhanced Dielectric Constant for Efficient Electromagnetic Shielding Based on Carbon-Nanotube-Added Styrene Acrylic Emulsion Based Composite

An efficient electromagnetic shielding composite based on multiwalled carbon nanotubes (MWCNTs)-filled styrene acrylic emulsion-based polymer has been prepared in a water-based system. The MWCNTs were demonstrated to have an effect on the dielectric constants, which effectively enhance electromagnetic shielding efficiency (SE) of the composites. A low conductivity threshold of 0.23 wt% can be obtained. An EMI SE of ~28 dB was achieved for 20 wt% MWCNTs. The AC conductivity (σ _ac) of the composites, deduced from imaginary permittivity, was used to estimate the SE of the composites in X band (8.2–12.4 GHz), showing a good agreement with the measured results.     

Multiwalled carbon nanotubes–BaTiO3/silica composites with high complex permittivity and improved electromagnetic interference shielding at elevated temperature

Composites with silica matrix and mixed filler of multiwalled carbon nanotubes (MWCNTs) and BaTiO₃ powder were fabricated. Excellent uniform dispersion of MWCNTs can be obtained using a two-step mixing method. Both of the real and imaginary parts of complex permittivity increased with increasing MWCNT content and measured temperature. The electromagnetic interference (EMI) shielding results showed that the absorption mechanism is the main contribution to the total EMI shielding effectiveness (SE). Compared with the EMI SE resulting from reflection, the absorption showed more dependence on the MWCNT content, measured temperature and frequency. The total EMI SE is greater than 20 dB at 25 °C and 50 dB at 600 °C in the whole frequency range of 12.4–18 GHz with a 1.5 mm composite thickness, which suggests that the MWCNT–BaTiO₃/silica composites could be good candidates for the EMI shielding materials in the measured frequency and temperature region.     

Effects of processing conditions on birefringence development in injection molded parts. II. Experimental measurement

The birefringence of injection molded parts was measured using a digital photoelasticity system, which combines a digital image analysis technique and the half-fringe photoelasticity (HFP) method The effects of processing conditions, including melt temperature, mold temperature, filling time and packing pressure, on the birefringence development in the molded parts were investigated. It was found that temperature and pressure are the two dominant factors that determine the birefringence development in the parts during the molding process. Frozen-in birefringence of the molded parts decreases with increasing melt temperature, mold temperature and injection speed. Birefringence of the parts also increases with increased packing pressure, especially around the gate area. Numerical simulations using the Leonov viscoelastic fluid model predict similar dependence of birefringence of parts on processing conditions. Simulated results are also consistent with measured values.     

Design and fabrication of long‐carbon‐fiber‐reinforced polyamide‐6/nickel powder composites for electromagnetic interference shielding and high mechanical performance

The long‐carbon‐fiber‐reinforced polyamide‐6/nickel powder composites were designed as electromagnetic interference (EMI) shielding materials and then were prepared through the joint processing of melt blending and thermoplastic pultrusion. The obtained composites show high conductivity and permittivity as well as a high dielectric loss with co‐addition of carbon fiber and nickel powders, which makes the resulting composites a higher level of shielding effectiveness due to the combination of conductive and magnetic fillers. The composites are capable of shielding mainly through absorption rather than reflection. On the other hand, the composites achieved significant improvements in tensile, flexural, and impact strength due to the superiority of the long‐carbon‐fiber‐reinforced technique. The residual fiber length in the injection‐molded specimens is greatly superior to the critical one predicted by the Kelly–Tyson model. This takes full advantage of the strength of the reinforcing fiber itself, thus leading to a promising reinforcement effect. The enhancement of impact toughness is due to the energy dissipation by fiber fracture as a result of long fiber effect. The morphologic investigation indicated that the fiber fracture and fiber pullout concurred on the impact and tensile fracture surfaces, and the former preceded the latter. Highlighted with both good EMI shielding properties and excellent mechanical performance, the composites designed by this work exhibit potential applications for the automotive, electronic, aerospace, and military industries. POLYM. COMPOS., 37:2705–2718, 2016. © 2015 Society of Plastics Engineers     

5‐Sulfoisophthalic acid monolithium salt doped polypyrrole/multiwalled carbon nanotubes composites for EMI shielding application in X‐band (8.2–12.4 GHz)

This article describes the synthesis and characterization of highly conductive polypyrrole (PPy)/multiwalled carbon nanotube (MWCNT) composites prepared by in situ polymerization of pyrrole using 5‐sulfoisophthalic acid monolithium salt [lithio sulfoisophthalic acid (LiSiPA)] as dopant and ferric chloride as oxidant. Several samples were prepared by varying the amounts of MWCNTs ranging from 1 to 5 wt %. Scanning electron microscope and transmission electron microscope images clearly show a thick coating of PPy on surface of MWCNTs. The electrical conductivity of PPy increased with increasing amount of MWCNTs and maximum conductivity observed was 52 S/cm at a loading of 5 wt % of MWCNTs. Pure PPy prepared under similar conditions had a conductivity of 25 S/cm. Electromagnetic interference (EMI) shielding effectiveness (SE) also showed a similar trend and average EMI shielding of ?108 dB (3 mm) was observed for sample having 5 wt % MWCNT in the frequency range of 8.2–12.4 GHz (X‐band). The light weight and absorption dominated total SE of ?93 to ?108 dB of these composites indicate the usefulness of these materials for microwave shielding. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45370.     

Effect of molecular weight and molding conditions on the replication of injection moldings with micro‐scale v‐groove features

Injection molded optical plastic parts require accurate replication of micro‐scale features. The effects of melt viscosity and molding conditions on replication of microscopic v‐groove features in injection molded parts were examined for PC with different molecular weight. The micro‐scale feature size was a continuous v‐groove with 20 μm in depth and 50 μm in width. For injection molding conditions, melt temperature, mold temperature, injection velocity and holding pressure were varied in three levels. As the result, the mold temperature had significantly affected replication for all polymers with different molecular weight. Additionally, the molding conditions that lower melt viscosity led to improved replication. In the case of polymer with high molecular weight, the viscosity decreased with increasing melt temperature. It has been found that high replication of micro‐scale features could be achieved by higher mold temperature and higher melt temperature even with high viscosity PC. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Multiwalled carbon nanotube/cement composites with exceptional electromagnetic interference shielding properties

Multi-walled carbon nanotube (MWCNT)/portland cement(PC) composites have been fabricated to evaluate their electromagnetic interference (EMI) shielding effectiveness (SE). The results show that they can be used for the shielding of EMI in the microwave range. The incorporation of 15 wt.% MWCNTs in the PC matrix produces a SE more than 27 dB in X-band (8.2–12.4 GHz), and this SE is found to be dominated by absorption. Furthermore, the structural analysis, surface morphology and surface interaction of MWCNTs with PC matrix have been explored using XRD, SEM and X-ray photoelectron spectroscopy technique.