Adhesion studies of tyre cords with rubber. I. Synthesis and characterization of natural rubber graft copolymers

Glycidyl methacrylate and N-vinyl pyrrolidone have been grafted onto natural rubber at 32°C using the simultaneous cobalt-60 irradiation technique. The natural rubber samples were swollen in the monomers for 24 h and thereafter subjected to gamma irradiation. The homopolymers formed in the graft copolymerization reactions and unreacted monomer were removed by solvent extraction using acetone and methanol for glycidyl methacrylate and N-vinyl pyrrolidone monomer, respectively. The influence of total dose and monomer concentration on the graft parameters was investigated. The dependence of the rate of grafting on the monomer concentration was found to be 0.93 and 0.80 for glycidyl methacrylate and N-vinyl pyrrolidone, respectively. DSC and TGA studies of the polymers were undertaken. Grafted copolymers based on glycidyl methacrylate were relatively less thermally stable compared with ungrafted natural rubber.     

Study of multi‐monomer melt‐grafting onto polypropylene in an extruder

Free‐radical melt‐grafting of the dual‐monomer systems glycidyl methacrylate–styrene (GMA‐St) and hydroxyethyl methacrylate–styrene (HEMA‐St) onto polypropylene (PP) has been studied using a single‐screw extruder. For single monomer grafting systems, degradation of PP was unavoidable and deterioration of the mechanical properties of the grafted PP subsequently occurred because of β‐scission of PP chains during the free‐radical melt‐grafting process. However, for the dual‐monomer systems, it is shown that the addition of styrene as a comonomer can significantly enhance the GMA or HEMA grafting levels on PP and reduce the extent of β‐scission of PP backbone. It has been found that the grafting degree of dual‐monomer melt‐grafted PP, such as PP‐g‐(GMA‐co‐St) or PP‐g‐(HEMA‐co‐St), is about quadruple that of single‐monomer grafted PP for the same monomer and dicumyl peroxide concentrations. Moreover, the melt flow rate of the dual‐monomer grafted PP is smaller than that of the unmodified PP. Hence, PP not only was endowed with higher polarity, but also kept its good mechanical properties. © 2000 Society of Chemical Industry     

Self‐driven graft polymerization of vinyl monomers on poultry chicken feathers in the absence of initiator/catalyst

An efficient and simple method for graft copolymerization of powdered chicken feather (CF) with vinyl monomers without any free radical initiator is reported. Various vinyl monomers such as glycidyl methacrylate (GMA), styrene (S), and methyl methacrylate (MMA); (20–60 wt % with respect to CF) were successfully grafted to chicken feather (CF) by using sodium dodecyl sulfate (SDS, 0.086–0.5 mmol) in the absence of any catalyst or initiator. Most likely, the hydrophilicity, hydrophobicity, and complex forming properties of chicken feather keratin with surfactant molecules were responsible for efficient grafting of polymers on CF surface. The effect of polymerization conditions, such as monomer concentration, temperature, and time of reaction, on the grafting parameters such as monomer conversion, grafting efficiency, and molar grafting ratio were studied. The described method showed a good potential of using low cost, easily accessible poultry chicken feathers as grafting material and self catalyzing agent for graft copolymerization with vinyl monomers to produce low cost commodity plastic for various end uses. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44645.     

Grafting of glycidyl methylacrylate onto chlorinated polypropylene and its bonding to aluminum flake

Glycidyl methacrylate (GMA) was grafted onto chlorinated polypropylene (CPP) in the molten state using benzoyl peroxide (BPO) in the presence of styrene (St) as a comonomer. The differential scanning calorimetry (DSC) results indicated that the thermodynamic curve of unpurified grafted CPP was different from the purified, and showed a new broad endothermic peak at 100°C, which may be attributed to the glass transition temperature (T_g) of remained copolymer of GMA and St. Furthermore, transmission electron microscope (TEM) showed that there were two‐phase structures in the grafted CPP. Because the grafted CPP was to be used as a hot melt adhesive, so the influence of initiator concentration, monomer concentration, and reaction temperature on peel strength was investigated. The experiment results showed that a higher degree of grafting was obtained by using two kinds of monomers, such as GMA and St. Increasing the monomer concentration led to an initial rapid increase in the peel strength. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2515–2521, 2007     

Factors affecting vapor phase photografting of vinyl monomers on cellulose

Effects of water contained in the sample, the type of sensitizer, and the nature of vinyl monomer on vapor phase photografting on cellulose were investigated at 60°C. The grafting was enhanced by the water contained in the cellulose sample, resulting in an increased percent grafting with increasing the quantity of water. The use of sensitizers such as ferric chloride, ferrous sulfate, ceric ammonium nitrate, hydrogen peroxide, benzophenone, and sodium anthraquinone-2,7-disulfonate led to accelerated graftings. However, the maximum grafting was observed at an optimum quantity of sensitizer for each sensitized system, and the formation of grafted polymer was restricted by the use of sensitizer beyond the quantity. Ferric chloride and hydrogen peroxide exhibited higher activities among the sensitizers. With respect to the nature of monomer, methyl methacrylate, acrylic acid, methacrylic acid, and acrylonitrile were observed to be introduced into cellulose substrate by the vapor phase photografting, though no initiation was recorded for styrene and N-vinylpyrrolidone. However, the latter monomers were introduced by using monomer mixtures with acrylonitrile, affording a maximum percent grafting at a certain monomer composition.     

Graft polymerization of vinyl acetate onto starch. Saponification to starch–g–poly(vinyl alcohol)

Graft polymerizations of vinyl acetate onto granular corn starch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinylacetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. However, over half of the polymer was present as ungrafted poly-(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficiency. However, grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate-methyl methacrylate was carried out near 0°C, although conversion of monomers to polymer was low and grafted polymer contained 40-50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch–g–poly(vinyl acetate) to starch–g–poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch–g–poly(vinyl alcohol) in hot water was less than 50%; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized starch for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch–g–poly(vinyl acetate) with about 35% add-on, and a grafting efficiency of about 40% was obtained. A film cast from a starch–g–poly(vinyl alcohol) copolymer in which homopolymer was not removed exhibited a higher ultimate tensile strength than a comparable physical mixture of starch and poly(vinyl alcohol).     

Styrene‐assisted melt‐free radical grafting of glycidyl methacrylate onto isotactic poly(1‐butene)

The melt‐free radical grafting of glycidyl methacrylate (GMA) onto powered isotactic poly(1‐butene) (iPB‐1) using styrene (St) as a comonomer in a Haake mixer was studied. The effects of temperature, initial GMA, and peroxide concentration, as well as the addition of St comonomer, on the final grafting degree, grafting efficiency, and the melt flow rate of grafted polymer were studied. It was shown that the addition of St as a comonomer could significantly enhance the grafting degree of GMA on iPB‐1 and reduce the extent of degradation of iPB‐1 to some degree. It has been found that the grafting degree of dual‐monomer melt‐grafted iPB‐1 was about twice that of single‐monomer‐grafted iPB‐1 for the same monomer and peroxide concentrations. The grafting of GMA onto iPB‐1 remarkably accelerated the crystal form II → I transformation of iPB‐1. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Study on antithrombosis dialytic membrane prepared by preirradiation grafting

A new antithrombosis dialytic membrane with a hydrophilic–hydrophobic microphase structure was prepared by preirradiation grafting of β‐hydroxyethyl methacrylate (HEMA) and styrene (St) onto ethylene–vinyl acetate (EVA). The influence of some effects, such as preirradiation dose, dose rate, grafting reaction temperature, reaction time, and monomer component, on the degree of grafting was determined, and the properties of the grafted films were investigated. Compared with the conventional EVA‐grafted hydrophilic monomer, the EVA films grafted with HEMA and St have superior antithrombogenicity; the antithrombogenicity and permeability of EVA‐g‐(HEMA‐co‐St) were 30 and 20 times higher than those of the ungrafted films, respectively, when the volume ratio (HEMA versus St) was about 7:3. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1321–1327, 2000     

GMA/St双组分单体熔融接枝聚丙烯的研究

分别以甲基丙烯酸缩水甘油酯（GMA）和马来酸酐（MAH）为接枝单体，苯乙烯（St）为接枝共单体，过氧化二异丙苯（DCP）为引发剂对聚丙烯（PP）进行熔融接枝，研究了接枝单体的种类、组分配比等因素对PP的接枝率和熔体流动速率等的影响，并研究了接枝PP的力学性能和耐热变形性能。实验结果表明：作为接枝单体，GMA比MAH更具有优越性；双组分单体熔融接枝PP的接枝率和性能优于单组分单体熔融接枝；接枝PP的结晶参数受其接枝率的影响；当PP／GMA／St／DCP=100／6／3／0、3时，PP—g^-（GMA—CO—St）的接枝率最高，力学性能和耐热变形性能最好。     

N-vinyl pyrrolidone-assisted free radical functionalization of glycidyl methacrylate onto styrene-b-(ethylene-co-butylene)-b-styrene

N-vinyl pyrrolidone (NVP)-assisted free radical functionalization of glycidyl methacrylate (GMA) onto styrene-b-(ethylene-co-butylene)-b-styrene (SEBS) was investigated to attempt to overcome the low grafting reactivity of GMA and the low efficiency of the styrene (St)-assisted functionalization method. By using the optimal amount of NVP, the degree of GMA grafting was increased by at least 7.5 and 2.5-fold when compared to GMA alone and the St-assisted grafting procedure, respectively. Also, no apparent cross-linking or degradation reactions of SEBS were observed. It was proposed that NVP reacted first with SEBS macroradicals, and then the resulting NVP-macroradicals copolymerized with GMA to produce high degrees of grafting of both GMA and NVP onto SEBS.     

Surface functionalization of Si3N4 nanoparticles by graft polymerization of glycidyl methacrylate and styrene

To improve dispersibility and interfacial interaction of nano‐Si₃N₄ particles in epoxy‐based composites, graft of glycidyl methacrylate (GMA) and styrene (St)/GMA onto the nanoparticles' surface was carried out in terms of emulsion polymerization method. The grafting polymers proved to be chemically attached to the nanoparticles via the double bonds introduced during the coupling agent pretreatment. The factors affecting the graft parameters, such as monomer concentration, initiator consumption, reaction time, etc., were investigated. It was shown that higher concentrations of monomer and initiator are favorable for the graft polymerization. When St/GMA was employed as the grafting monomer, the nanoparticles were found to play the role of polymerization loci. The grafted nanoparticles exhibit greatly improved dispersibility in cured epoxy. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 992–999, 2006     

Photografting of N‐isopropylacrylamide and glycidyl methacrylate binary monomers on polyethylene film: Effect of mixed solvent consisting of water and organic solvent

Photografting (λ > 300 nm) of N‐isopropylacrylamide (NIPAAm) and glycidyl methacrylate (GMA) binary monomers (NIPAAm/GMA) on low‐density polyethylene film (thickness = 30 μm) was investigated at 60°C using mixed solvent consisting of water and an organic solvent such as acetone. Xanthone was used as a photoinitiator by coating it on the film surfaces. A maximum percentage of grafting was observed at a certain concentration of acetone in the mixed solvent, which was commonly observed for both ratios of NIPAAm/GMA, 8/2 and 7/3. Based on the photografting of NIPAAm/GMA on xanthone‐coated film, monomer reactivity ratios of NIPAAm (r₁) and GMA (r₂) were calculated using the Fineman–Ross method. The values were 0.31 ± 0.1 and 4.8 ± 0.2 for the water solvent system, while they were 0.96 ± 0.1 and 4.9 ± 0.1 for the mixed solvent system. NIPAAm/GMA‐grafted films with a homogeneous distribution of grafted chains were formed by photografting using water and mixed solvents. The NIPAAm/GMA‐grafted films exhibited temperature‐responsive characters, whereas the grafted films showed a reversible change in the degree of swelling between 0 and 50°C, respectively. Epoxy groups in the grafted poly(NIPAAm/GMA) chains could be aminated with ethylenediamine in N,N′‐dimethylformamide at 70°C for 3 h. Complexes of the aminated NIPAAm/GMA‐grafted chains with cupric ion exhibited catalytic activity for the decomposition of hydrogen peroxide at 20 to 50°C. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2469–2475, 2005     

Photografting of PVC containing N,N‐diethyldithiocarbamate groups with vinyl monomers

Poly(vinyl chloride) (PVC) with pendent N,N‐diethyldithiocarbamate groups (PVC–SR) was prepared through the reaction of PVC with sodium N,N‐diethyldithiocarbamate (NaSR) in butanone and used as a photoinitiator for the grafting polymerization of three vinyl monomers [styrene (St), methyl methacrylate (MMA), and acrylamide (Am)]. The effects of ultraviolet (UV) irradiation time, PVC–SR amount, and the monomer amount on grafting and grafting efficiency were investigated. The results showed that PVC–SR could initiate the polymerization of three vinyl monomers effectively and obtained crosslinked copolymers. The grafting and grafting efficiency of styrene and methyl methacrylate were higher than those of acrylamide. The polymerization activity of three monomers was acrylamide > methyl methacrylate > styrene. By analyzing the UV spectrum of PVC–SR with a different irradiation time, it was confirmed that PVC–SR was dissociated mainly into macromolecular the sulfur radical PVC–S · and the small molecular carbon radical · C(S)N(C₂H₅)₂; the grafting polymerization mechanism was discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2569–2574, 2000     

Hydrogel coating of RVNRL film by electron‐beam irradiation

The tackiness properties of radiation‐vulcanized natural rubber latex (RVNRL) film surfaces coated by various monomers were investigated in order to define the suitable hydrogels which reduce the tackiness of the film. In this context, different types of monomers, namely, N‐vinyl‐2‐pyrrolidone (NVP), N,N‐dimethylaminoethylamide (DMAEA), acrylic acid (AAc), n‐butyl acrylate (n‐BA), and 2‐hydroxyethyl methacrylate (HEMA) as well as the monomer mixtures were tried with varying degrees of success. Coating the RVNRL film with 80% HEMA/20% n‐BA by irradiation at 80 kGy using a low‐energy electron beam gave a remarkable reduction in the surface tackiness of the RVNRL film. Several other attempts were made such as priming the RVNRL film with acid and aluminum sulfate prior to coating, mixing the aluminum sulfate into the monomer mixtures, and dipping the partially wet RVNRL film into the monomer to enhance the wettability of the monomers with the film. The photomicrographs taken illustrate that the decrease in tackiness with the coating is due to the increase of the surface roughness at an 80‐kGy irradiation dose. The studies also revealed that the reduction in the contact angle and the increase in water absorption of the RVNRL film after irradiation are due to the formation of the hydrogel layer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1421–1428, 1999     

Radiation‐induced GMA/DMAA graft copolymerization onto porous PE hollow‐fiber membrane

Radiation‐induced graft copolymerization is a powerful technique to prepare a grafted chain with the desired properties pending onto the trunk material. In this work, a polyethylene hollow‐fiber membrane was modified by this technique. The monomers glycidyl methacrylate (GMA) and N,N‐dimethylacrylamide (DMAA) were cografted onto macroporous polyethylene hollow fiber with a grafting degree in the order of 200%. DMAA/GMA cografted membranes were compared to GMA grafted ones for the introduction of an amino acid as a specific ligand. Grafted membranes with a copolymer composition between 0 and 2 DMAA/GMA were prepared by soaking them in solutions of different mixtures of monomers. Copolymers were characterized by FTIR and their composition was estimated by the analysis of the ratio of carbonyl signals. Copolymers with a higher proportion of DMAA showed improved hydrophilic properties and higher conversion rates of epoxy groups on phenyalanine ligands than those of the GMA grafted ones. However, copolymers with a DMAA/GMA ratio higher than 1 showed a detrimental effect on the pure water flux. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1646–1653, 2003     

Grafting. III. Copolymerization of methyl methacrylate and methacrylic acid

The method of graft copolymerization of methyl methacrylate on halogen-containing polymer has been utilized for grafting of methyl methacrylate–methacrylic acid monomer pair onto poly(vinyl chloride) and chlorinated rubber. Substantial grafting could be obtained by using the method reported earlier. However, the compositions of the grafted chains are found to deviate appreciably from the compositions calculated from r₁ and r₂ values reported in literature. The reactivity ratios for this pair of monomers have been therefore evaluated using azobisisobutyronitrile and n-butane thiol–dimethyl sulfoxide as initiators. The anomalies of the grafted chain compositions have been discussed and an explanation presented on preferential solvation.     

Graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto silica surface by Michael addition

The introduction of peroxycarbonate groups onto a silica surface and the graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto a silica surface were investigated. The introduction of peroxycarbonate groups onto a silica surface was achieved by Michael addition of amino groups introduced onto the silica surface to t‐butylperoxy‐2‐methacryloyloxyethylcarbonate (HEPO). The amount of peroxycarbonate groups was determined to be 0.17 mmol/g. The graft polymerization of various vinyl monomers such as styrene (St), N‐vinyl‐2‐pyrrolidinone (NVPD), and 2‐hydroxyethyl methacrylate (HEMA) was initiated by peroxycarbonate groups introduced onto the silica surface to give the corresponding polymer‐grafted silicas. The percentage of poly(St)‐grafting reached about 120% after 5 h. This means that 1.20 g of poly(St) is grafted onto 1.0 g of silica. The surface of poly(St)‐grafted silica shows a hydrophobic nature, but the surfaces of poly(NVPD) and poly(HEMA)‐grafted silica show a hydrophilic nature. Furthermore, the poly(St)‐grafted silica was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1491–1497, 1999     

Preparation of soapless latexes by sonification of starch-based poly(isoprene–co–acrylonitrile) graft reaction mixtures

Graft copolymerization of isoprene (IP) and acrylonitrile (AN) onto gelatinized starch (S) and cationic starch having quaternary amine functionality through cerium(IV) initiation gave grafted side chains of poly(IP–co–AN). Grafts of various compositions are obtained by controlling the amounts and ratios of monomers added to starch. IP alone does not homograft onto gelatinized starch at 25° or 50°C by cerium(IV) initiation and requires the presence of an “initiator–monomer” such as AN to obtain copolymer side chains. Although cografting of IP and AN onto starch depends on AN to initiate radical chains, the ratio employed of the two monomers is critical for graft polymerization to occur. For example, at a molar ratio of IP to AN of 1 or greater, little polymer was produced; at molar ratios in the range of 0.4 to 0.67, considerable amounts of polymer were produced; and at a molar ratio of 0.13 or less, polymerization of AN was greatly retarded. Concentration of HNO₃ in the cerium(IV) reagent and reaction temperature also influence the grafting reaction. Lower HNO₃ concentrations favor grafting at 50°C, while higher acid concentrations favor grafting at 25°C. Starch graft reaction mixtures were sonified at 20 kHz to form latexes that air dry to clear pliable films. Poly(IP–co–AN) obtained by acid hydrolysis of the starch portion of the grafts failed to dissolve in either dimethylformamide or benzene, thus indicating presence of crosslinks. S–g–poly(IP–co–AN), having about one third starch and grafted side chains averaging about 2 parts polymerized IP per part of polymerized AN, was masticated on steel rolls at 100°C to a tough pliable film which was subsequently vulcanized to a rubber.     

Surface modification of poly(vinyl chloride) for antithrombogenicity study

A process was established to conduct heparinization on the surface of poly(vinyl chloride) for antithrombogenicity utilization. A bifunctional monomer, glycidyl methacrylate (GMA), was grafted onto the surface of PVC by gas‐phase photografting polymerization without degassing first; then heparin was immobilized onto the poly(glycidyl methacrylate) segments. The branch structure of GMA and heparin were characterized by Fourier transfer infrared (FTIR) spectroscopy and electron spectroscopy (ESCA). It was confirmed that the bifunctional monomer GMA and heparin were grafted successfully onto the surface of PVC. The antithrombogenicity of the samples was tested both in vitro and in vivo, respectively. Results indicated that the blood compatibility of those products was improved greatly. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1013–1018, 2002     

Reconsideration on the mechanism of free-radical melt grafting of glycidyl methacrylate on polyolefin

The styrene (St) assisted melt grafting of glycidyl methacrylate (GMA) on polyolefin was carried out by Haake mixer, and the grafting mechanism was investigated and reconsidered. It was revealed that there is equilibrium of grafting of GMA and depolymerization of grafted PGMA chains in the GMA/polyolefin grafting process, which was affected by both of the temperature and GMA concentration. It was found that the depolymerization of PGMA grafted on polyolefin occurred at the temperature above ceiling temperature of PGMA and dominated the grafting process before the addition of styrene monomer, which induced the decrease in grafting ratio of GMA. Adding styrene as co-monomer could promote the equilibrium moving forward to form the St-GMA chains so that the grafting ratio was greatly improved. It is proved that either controlling the reacting temperature below the ceiling temperature or changing the feeding order of styrene and GMA is effective to attain high grafting ratio of GMA on polyolefin.