Effects of synthesis conditions on radiation-induced graft copolymerization of methacrylic acid on to poly(vinyl chloride) films

Poly(vinyl chloride) (PVC) films were grafted with methacrylic acid (MAA) using a simultaneous-irradiation technique. The effect of solvent ratio (methanol-water) on grafting was studied and maximum grafting was found for an equivolume mixture of methanol and water. The graft level increased with increase of the plasticizer (dioctylphthalate) content in PVC. Grafting was found to be higher at low dose rate and increased linearly up to 0.25 Mrad for all dose rates and then levelled off. Grafting also increased continuously with increasing monomer concentrations up to 5.4mol/litre, but a linear increase in grafting was observed only up to 2.5 mol/litre. The dependences of rate of grafting on dose rate and monomer concentration were found to be 0.62 and 1.20 respectively.     

Synthesis and characterization of an interpenetrating polymer network composed of poly(methacrylic acid) and poly(vinyl alcohol)

Temperature and pH‐responsive interpenetrating polymer network (IPN) hydrogels, constructed with poly(methacrylic acid) (PMAA) and poly(vinyl alcohol) (PVA), by a sequential IPN method, were studied. The characterization of IPN hydrogels was investigated by Fourier‐transform infrared spectroscopy, differential scanning calorimetry (DSC) and swelling under various conditions. The IPN hydrogels exhibited relatively high swelling ratios, in the range 230–380 %, at 25 °C. The swelling ratios of the PMAA/PVA IPN hydrogels were pH and temperature dependent. DSC was used for the quantitative determination of the amounts of freezing and non‐freezing water. The amount of free water increased with increasing PMAA content in the IPN hydrogels. Copyright © 2004 Society of Chemical Industry     

Improving the antifouling property of poly(vinyl chloride) membranes by poly(vinyl chloride)‐g‐poly(methacrylic acid) as the additive

To improve the antifouling property of poly(vinyl chloride) (PVC) membranes, a series of poly(methacrylic acid) grafted PVC copolymers (PVC‐g‐PMAA) with different grafting degree were synthesized via one‐step atom transfer radical polymerization process utilizing the labile chlorines on PVC backbones followed by one‐step hydrolysis reaction. PVC/PVC‐g‐PMAA blend membranes with different grafting degree and copolymer content were prepared by nonsolvent induced phase separation method. The surface chemical composition, surface charge, membrane structures, wettability, permeability, separation performances and the fouling resistance of blend membranes were carefully investigated. The results indicated that the PMAA chains were segregated towards the surface and the membranes were endowed with negative charge. The hydrophilicity and permeability of the blend membranes were obviously improved. Furthermore, the antifouling ability especially at neutral or alkaline environments was also significantly increased. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42745.     

聚甲基丙烯酸-苯乙烯-甲基丙烯酸的合成

以萘钠为引发剂双向引发活性阴离子聚合制备嵌段共聚物聚甲基丙烯酸叔丁酯-苯乙烯-甲基丙烯酸叔丁酯(PTBMA—PS—PTBMA)，并在碱性条件下水解合成了ABA型两亲嵌段共聚物聚甲基丙烯酸-苯乙烯-甲基丙烯酸(PMAA—PS—PMAA)。对产物进行了傅立叶红外光谱分析，热分析及凝胶色谱分析。当苯乙烯与α-甲基丙烯酸叔丁酯投料质量比为54：46时，所得共聚物相应嵌段质量比为79：2l左右。     

The influence of poly(vinyl alcohol) suspending agents on suspension poly(vinyl chloride) morphology

The requirements for PVC suspension resin have changed considerably in the last few years, so much so that few companies have products on their ranges that are more than 4 or 5 years old. The suspending agent has a crucial influence on the morphology of the resin, so the changes in resin characteristics have largely been achieved by changes in the suspending agent systems. After a brief review of the mechanism of PVC suspension polymerisation, the properties of polymers made using PVOH suspending agents are related to changes in the latter. The effect of variations in PVAc degree of hydrolysis and viscosity are related to changes in surface tension. Methods of achieving higher porosity by using low hydrolysis co-suspending agents are described. It is shown that higher bulk densities can be achieved by delayed addition of the PVOH. Levels of conjugated unsaturation and copolymer distributions are also shown to have important influences.     

Complexation between poly(methacrylic acid) and poly(vinylpyrrolidone)

The complexation between poly(methacrylic acid) (PMAA) and poly(vinylpyrrolidone) (PVP) in aqueous phase was studied by various fluorescence techniques, including fluorescence anisotropy measurements, fluorescence probe studies, and nonradiation energy transfer. It was demonstrated that the complexation of PMAA with PVP occurs within a pH range of 1 to 5 and along with complexation, the conformation of PMAA changed from a hypercoiled to a loosely coiled form. The complex ratio between the two polymers is 2:1 (PMAA/PVP, in monomer unit). Salt effect studies showed that the complexation occurred due to formation of hydrogen bonds between the two polymers. Based on these conclusions and the “connected cluster model” for PMAA at low pH, a “ladder with connected cluster” model was proposed for the structure of PMAA/PVP complex formed at low pH. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 620–627, 2001     

Studies of electrical and mechanical properties of semiconductive poly(vinyl chloride) compositions

A sample of poly(vinyl chloride) (PVC) and a polar plasticizer consisting of dioctylphthalate (DOP) and triisopropylphenylphosphate (TIPPP) was prepared and found to possess some electrical conductivity. Different samples of PVC compositions were formulated from the PVC-DOP-TIPPP system and also variable proportions of the conductive materials polyaniline or the Ni salt of ethylene glycol bisadipate ester. Dibutyltindilaurate as a heat stabilizer, titanium oxide as a filler, and sandorin red 20 pigment were added. The effect of the structure of polyaniline and Ni adipate ester on the electrical and mechanical properties of the PVC–DOP–TIPPP system was studied to obtain a semiconductive plasticized PVC with good mechanical properties. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 685–693, 1998     

Stabilization of poly(vinyl chloride) by elemental sulfur

The process of stabilization of a poly(vinylchloride) elemental sulfur in thermal and thermooxidative destruction conditions is investigated. The high stabilizing efficiency of elemental sulfur is revealed at the destruction of plasticized poly(vinylchloride) compared with the efficiency of phenolic antioxidants. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Peroxide crosslinking of unplasticized poly(vinyl chloride)

A crosslinking system consisting of 1,1‐di‐t‐butylperoxy‐3,3,5‐trimethyl cyclohexane peroxide and trimethylolpropane trimethacrylate (TMPTMA) has been used to introduce crosslinks into unplasticized poly(vinyl chloride) (PVC). The influence of the concentration of both reagents has been investigated, and crosslinking monitored by determination of the remaining sample weight after Soxhlet extraction with tetrahydrofuran. The system used (i.e., 0.5–2.0 phr peroxide with 5 to 15 phr TMPTMA) has been shown to be effective for crosslinking PVC. Gel contents of 30–40% have been obtained, premature crosslinking during processing is largely avoided, but thermal stability still needs to be improved. Considerable improvements in elevated temperature mechanical properties can be attained using an appropriate TMPTMA/peroxide concentration. The best tensile properties were obtained with 0.5 phr peroxide and 15 phr TMPTMA. Observed increases in T_g, also achievable with only 0.5 phr peroxide, but only slightly dependent on TMPTMA concentration, represent a useful increase in service temperature for the resulting compound. Lower peroxide levels may be adequate to achieve property improvements. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2657–2666, 2000     

Blends of plasticized poly(vinyl chloride) and waste flexible poly(vinyl chloride) with waste nitrile rubber powder

Blends of poly(vinyl chloride) (PVC) with varying contents of plasticizer and finely ground powder of waste nitrile rubber rollers were prepared over a wide range of rubber contents through high‐temperature blending. The effects of rubber and plasticizer (dioctyl phthalate) content on the tensile strength, percentage elongation, impact properties, hardness, abrasion resistance, flexural crack resistance, limiting oxygen index (LOI), electrical properties, and breakdown voltage were studied. The percentage elongation, flexural crack resistance, and impact strength of blends increased considerably over those of PVC. The waste rubber had a plasticizing effect. Blends of waste plasticized PVC and waste nitrile rubber showed promising properties. The electrical properties and LOI decreased with increasing rubber and plasticizer content. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1552–1558, 2004     

Soiling of plasticized poly(vinyl chloride)

The effects of three plasticizers and two plasticizer concentrations on the topography and soiling of poly (vinyl chloride) (PVC) were studied. Palmitic acid and triolein were chosen to represent solid and liquid soils. The feasibility of using infrared spectroscopy to quantify the amount of soil on PVC was examined. The structure of the solid model soil on plasticized PVC was studied with optical microscopy and atomic force microscopy. Palmitic acid formed two different structures on the PVC surface. Both the type and concentration of the plasticizer influenced the structure of the oily soil on plasticized PVC. The wetting of plasticized PVC with the liquid oily soil was compared to wetting with water through the measurement of the contact angles. Plasticized PVC was hydrophobic and oleophilic. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Development of nanocomposites of bentonite with polyaniline and poly(methacrylic acid)

Nanocomposites of bentonite with polyaniline (PANI), poly(methacrylic acid) (PMAA), and poly(aniline‐co‐methacrylic acid) (PANI‐co‐PMAA) were prepared by in situ intercalative polymerization technique. The nanocomposites were characterized by FTIR and UV–visible spectroscopies, XRD, SEM, TEM, as well as TG‐DTA studies. The in situ intercalative polymerization of PANI, PMAA, and PANI‐co‐PMAA within bentonite layers was confirmed by FTIR, XRD, SEM, as well as TEM studies. XRD confirmed the intercalation of polymers and copolymer in bentonite. The average particle size of the nanocomposites was found to be in the range of 250–500 nm. The thermal stability was found be the highest for PANI‐co‐PMAA‐bentonite. The swelling behavior studies suggest that these nanocomposites hold potential for their utilization in absorption of toxic materials from waste water. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3299–3306, 2007     

Influences of individual and composed poly(vinyl alcohol) suspending agents on particle morphology of suspension poly(vinyl chloride) resin

Effects of individual and composed poly(vinyl alcohol) (PVA) suspending agents on the particle morphology of poly(vinyl chloride) (PVC) resins were investigated and discussed in the view of PVA absorption at the oil/water interface and interfacial behavior. It was shown that the percentage and surface coverage of PVA at the oil/water interface decreased with the increase of the degree of hydrolysis (DH) of PVA in the DH range of 70–98 mol %, while the interfacial tension of VC/PVA aqueous solution increased linearly with the increase of DH of PVA. PVC resin with more regular particle shape, increased agglomeration and fusion of primary particles, lower porosity and higher bulk density, was prepared by using PVA with a higher DH as a suspending agent. This was caused by the occurrence of drop coalescence at the very early stage of VC polymerization, the increase of particle shrinkage, and the lower colloidal protection to primary particles. It was also shown that the interfacial tension of VC/water in the presence of composed PVA suspending agents varied linearly with the weight composition of the composed PVA suspending agents. The particle properties of PVC resin prepared by using the composed PVC suspending agents were usually situated in between the properties of PVC resins prepared by using the corresponding individual PVA suspending agent. The particle morphology and properties of PVC resin could be controlled by the suitable choice of the composed PVA suspending agents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3848–3855, 2003     

In-situ polymerization of n-butyl acrylate in poly(vinyl chloride)

The in situ polymerization of n-butyl acrylate with poly(vinyl chloride) has been studied. Butyl acrylate was polymerized using a peroxydicarbonate initiator and a thiol chain transfer agent in the presence of poly (vinyl chloride) beads suspended in water. The products were examined, after pressing into sheets, for optical clarity and by dynamic mechanical analysis. It was found that if 10% butyl acrylate was peesent in the mixture homogeneous blends were formed but if 15% or more butyl acrylate was present two phase mixtures were formed. If homogeneous blends prepared as above were reswollen in butyl acrylate, and the latter then polymerized, homogeneous blends containing more poly(butyl acrylate) could be prepared. The interaction parameters between both poly(vinyl chloride' and poly(butyl acrylate) and butyl acrylate were estimated by inverse gas chromatography. Using these and an estimate of the polymer/polymer interaction parameter the three component phase diagram could be qualitatively explained.     

Synthesis of glycidylethylhexylphthalate and its effects on poly(vinyl chloride) films as a novel plasticizer

To improve the processability and prevent the thermal degradation of poly(vinyl chloride) (PVC), various plasticizers and heat stabilizers have to be compounded. Phthalic plasticizers and metal soap stabilizers are usually used with epoxides as costabilizers. Epoxidized soybean oil (ESO), is one of the most commonly used epoxides because of its typical combined roles as a plasticizer and heat stabilizer in PVC compounds. ESO, however, sometimes causes surface contamination of PVC compounds because saturated fatty acids such as stearic and palmitic acids in soybean oil easily bleed onto the surface. In addition, some ingredients in ESO with hydroxide groups and unreacted double bonds during epoxidization also tend to increase the bleeding of ESO. This is due to their low compatibility with PVC resins. In this study, a novel plasticizer of PVC resins, glycidylethylhexylphthalate (GEHP), was synthesized, and its performance was evaluated. GEHP was designed to act as a plasticizer like normal phthalic plasticizers and to act as a heat stabilizer like ESO. Through the addition of epoxy groups in phthalic compounds, the resistance to bleeding was improved, and the plasticizing and heat‐stabilizing effects on the PVC compounds were preserved. Soft PVC films were prepared with GEHP. The mechanical properties, thermal stability, and bleeding properties of the films were investigated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1347–1356, 2005     

Studies of polyester/chlorinated poly(vinyl chloride) blends

Chlorinated poly(vinyl chloride) (CPVC) was solution blended with poly(caprolactone) (PCL), poly(hexamethylene sebacate) (PHMS), poly(α-methyl-α-n-propyl-β-propiolactone) (PMPPL), poly(valerolactone) (PVL), poly(ethylene adipate), poly(ethylene succinate) and poly(β-propiolactone). From calorimetric glass transition temperature (T_g) measurements, it is concluded that CPVC is miscible with polyesters having a CH₂/COO ratio larger than three (PCL, PHMS, PMPPL and PVL). The Gordon-Taylor k parameter was also calculated and found equal to 1.0 and 0.56 for PCL/CPVC and PHMS/CPVC blends, respectively. From these values, it is concluded that CPVC gives a stronger interaction with polyesters than poly(vinyl chloride) due to its larger chlorine content.     

Contributions to characterization of poly(vinyl chloride)–lignin blends

The present study evaluates the impact of blending organosolv and kraft lignins, which are natural polymer by‐products in the pulp and paper industry, with plasticized poly(vinyl chloride) (PVC) in flooring formulations. Also examined is the impact of replacing dioctyl phthalate, a PVC industry general‐purpose plasticizer, with diethylene glycol dibenzoate (Benzoflex 2‐45), tricresyl phosphate (Lindol), or alkyl sulfonic phenyl ester (Mesamoll) in these formulations. The influence of the different types of lignins and plasticizers on the processibility, thermal, and mechanical properties of the blends is discussed. These properties demonstrate that partial replacement of PVC (20 parts) with different lignins is feasible for some formulations that can be successfully used as matrices for a high level of calcium carbonate filler in flooring products. In addition, the data demonstrate that the presence of certain plasticizers, which interfere with the intramolecular interactions existing in lignins, may allow the lignin molecules to have more molecular mobility. The morphology and the properties of PVC plasticized lignin blends are strongly influenced by the degree and mode of the lignin plasticization and its dispersion within the PVC matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2732–2748, 2006     

Preparation and structural characterization of nanocrystalline poly(vinyl chloride)

This article describes the development of novel nanocrystalline poly(vinyl chloride) (PVC) for potential applications in PVC processes and reports improvements in the mechanical properties and thermal resistance. Before the preparation of nanocrystalline PVC via jet milling, PVC was spray‐treated and heat‐treated to improve its crystallinity. The pulverization and degradation, morphology, crystalline structure, and melting‐point changes of postmodified PVC during jet milling and the relationship between the distributions of the particle size and processing temperature were investigated. X‐ray analysis and density testing indicated increased density and improved crystallinity. The crystalline region of nanocrystalline PVC was less than 80 nm, with a particle size distribution of 5–20 μm and a melting point of less than 128°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 563–569, 2004     

Poly(acrylic acid)–poly(vinyl alcohol) copolymers with superabsorbent properties

Biodegradable polyacrylates were produced by a series of novel copolymerization and/or crosslinking techniques using poly(vinyl alcohol) (PVA) moieties modified by the incorporation of olefinic structures. PVA was modified by a tosylation and/or detosylation reaction. The functionalized PVA was copolymerized and/or crosslinked with acrylic acid or its partially neutralized form to give crosslinked polyacrylates that could swell in water. Their swelling behavior was determined under load. Degradation studies were performed in α-chymotrypsin, trypsin, and papain solutions. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 817–829, 1998