适用于微型燃料电池扩散层的多孔硅的可控制备工艺研究

多孔硅以其多孔结构及大的表面体积比等特点被认为是可在基于MEMS技术的微型燃料电池中代替碳 纸、碳布作为扩散层的材料. 本文考虑传统碳纸、碳布作为扩散层的要求, 并结合多孔硅材料的特点, 选用n<100>(0.04～0.15 Ω·cm)单晶硅进行了多孔硅制备工艺的研究; 考察了腐蚀液的浓度、电流密度和氧化处理时间对多孔硅的孔隙率、孔深度及氧化速率 的影响, 实现了多孔硅的可控制备. 孔隙率为40%、孔径为350～700nm、厚度为60μm的多孔硅膜电极经循环伏安测定, 在0.5mol/L H₂SO₄溶液中, 表现出与碳纸相近的电活性, 显示了潜在的应用价值.     

硅基发光材料研究进展

硅基发光材料是光电子集成的基础材料。发光多孔硅是硅基发光材料的一个新进展，已实现了硅基光电子集成。随着多孔硅研究的深化和纳米科学的发展，硅基发光材料正向纳米方向开拓，与此同时，在新的理论认识与技术条件下，硅材料改性，杂质发光，缺陷工程和硅然异质外延也呈现出新的发展趋势。     

锂离子电池多孔硅/碳复合负极材料的研究

以商业化多晶硅粉为原料, 采用金属银催化剂诱导化学腐蚀的方法制得三维多孔硅材料。通过优化腐蚀条件, 得到孔径约为130 nm, 比表面为4.85 m²/g的多孔硅材料。将多孔硅和PAN溶液混合球磨并经高温烧结后在多孔硅表面包覆上一层致密的无定形碳膜, 从而制得多孔硅/碳复合材料作为锂离子电池的负极材料。3D多孔硅结构可以缓解电化学嵌/脱锂过程中材料的体积效应, 无定形碳膜层可有效改善复合材料的导电性能。电化学性能测试表明, 该多孔硅/碳复合负极材料电池在0.4 A/g的恒电流下, 首次放电容量3345 mAh/g, 首次循环库伦效率85.8%, 循环55次后容量仍保持有1645 mAh/g。并且在4 A/g的倍率下, 容量仍维持有1174 mAh/g。该方法原料成本低廉, 可规模化生产。     

利用UHV／CVD技术在双层多孔硅上外延硅研究

利用ＵＨＶ／ＣＶＤ技术，在较低的温度下，在阳极氧化形成的双层多孔硅上，成功地生长了单晶性好、厚度均匀、电阻率分布合适的硅单晶外延层。这为进一步研制了ＳＯＩ材料与器件提供了所需的薄硅外延层。     

阳极氧化电流密度和时间对多孔硅形貌和电子发射特性的影响

为了应用于场发射显示器,采用电化学阳极氧化,快速热氧化和磁控溅射等方法制备出了金属/多孔硅/硅基底/金属结构的多孔硅电子发射体,并运用扫描电子显微镜观察了多孔硅的微观形貌,结果发现多孔硅的孔径随着电化学阳极氧化电流密度的增加而增加,多孔硅层的厚度随着阳极氧化电流密度和时间乘积的增加而增加。在真空系统中测量了多孔硅的电子发射特性,电子发射的阈值电压Vth随着多孔硅层厚度的增加而增加;最大的发射效率η为7.5‰,此效率出现在孔径6~16 nm,多孔硅层厚度为11.06μm的样品中,对应的器件电压Vps为30V。     

源于溪木贼的高性能锂离子电池三维多孔生物质硅/碳复合负极材料

锂离子电池硅基负极材料的理论比容量比传统石墨材料高10倍,是最有前途的锂离子电池负极材料之一.然而硅基纳米材料的制备工艺复杂、成本高昂,严重限制了锂离子电池硅负极的商业应用.本工作采用溪木贼为原料,通过深度还原、浅度氧化和碳包覆工艺制备了三维多孔生物质硅/碳复合材料(多孔3D-bio-Si/C).三维多孔结构不仅有利于...     

用脉冲电化学法在低HF浓度下制备多孔硅的研究

用脉冲电化学阳极氧化的方法在5％的低HF浓度下获得多孔硅。多孔硅的形成和脉冲电场的施加、去除过程中与电解液－硅半导体体系中物理化学过程的变化有关。在施加电场的间隙，由于Si／电解液界面处HF的补充，SiO2的溶解增强，使得在低HF浓度下Si的溶解速率比其氧化速率高，从而导致多孔硅的形成。同时，在高电场作用下，由于产生了高浓度的空穴，使得氧化层变厚，导致在低HF浓度或大电流密度下多孔硅的平均孔径增大。     

利用UHV／CVD技术在双层多孔硅上外延硅研究

利用 UHV/CVD技术 ,在较低的温度下 ,在阳极氧化形成的双层多孔硅上 ,成功地生长了单晶性好、厚度均匀、电阻率分布合适的硅单晶外延层。这为进一步研制 SOI材料与器件提供了所需的薄硅外延层。     

硅的阳极氧化研究——多孔硅的制备及其发光机制

评介了阳极氧化方法制备多孔硅（Ｐｏｒｏｕｓ Ｓｉｌｉｃｏｎ）的工艺，讨论了多孔硅的形貌及发光机制。     

超高真空电子束蒸发在多孔硅上外延单晶硅

采用超高越空电子束蒸发的方法在用阳极氧化制备的多孔硅衬底上外延单晶硅,研究了不同多孔硅衬底对外延质量的影响。采用高能电子衍射表征外延层的晶体结构,截面透射电镜上材料的微结构,原子力镜表征外延层表面的粗糙度,卢瑟福背散射／沟道表征外延层晶体质量,扩展电阻表征材料的电学性能。一系列的测试结果表明对在5mA／cm^2电流密度下阳极氧化10min形成的多孔硅衬底,可用超高真空电子束蒸发的方法外延出质量良好的单晶硅。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.