Shock response of stainless steel at high temperature

Measurements of the dynamic tensile strength of HR-2 (Cr-Ni-Mn-N) stainless steel have been carried out over the initial temperature range of 300 K–1000 K at shock stress of 8 GPa, the corresponding spall strength _f and Hugoniot elastic limit _HEL are determined from the wave profiles. In the temperature range of 300 K–806 K, _f and _HEL decrease linearly with increasing temperature T, i.e., _f = 5.63-4.32 × 10^–3T, _HEL = 2.08-1.54 × 10^–3T, but when heated to 980 K, _HEL increases from 0.84 GPa at 806 K to 0.93 GPa at 980 K and _f keeps at an almost fixed value of 2.15 GPa. The TEM analysis on recovery samples identified the existence of intermatallic compound Ni₃Al and the carbide Cr₂₃C₆ in the sample of 806 K, another intermatallic compound Ni₃Ti was found in the sample of 980 K. All these products emerge along crystal boundary. While no such products were found in the samples of 300 K and 650 K.     

Quantum statistical foundation to the fermi liquid model and Ginzburg-Landau wave function

An energy eigenvalue equation for a quasi-particle is derived, starting with the Heisenberg equation of motion for an annihilation operator. An elementary derivation of the Fermi liquid model having a sharply defined Fermi surface in thek-space is given, starting with a realistic model of a metal including the Coulomb interaction amongand between electrons and lattice-ions. The Ginzburg-Landau wave function (r), where represents the superconducting pairon (Cooper-pair) state, is shown to be connected with the one-pairon density operatorn by (r) = r¦_n ^1/2¦. A close analogy between supercurrent and laser is indicated.On sabbatical leave from Department of Physics and Astronomy, State University of New York at Buffalo, Buffalo, New York.     

Stress relaxation in hot-drawn low density polyethylene

The tensile stress relaxation behaviour of hot-drawn low density polyethylene, (LDPE), has been investigated at room temperature at various draw ratios. The drawing was performed at 85° C. The main result was an increase in relaxation rate in the draw direction, especially at low draw ratios when compared to the relaxation behaviour of the isotropic material. This is attributed to a lowering of the internal stress. The position of the relaxation curves along the log time axis was also changed as a result of the drawing, corresponding to a shift to shorter times. The activation volume, , varied with the initial effective stress ₀ ^* according to ₀ ^* 10kT, where ₀ ^* =₀ — _i, is the difference between the applied initial stress, ₀, and the internal stress _i. This result supports earlier findings relating to similarities in the stress relaxation behaviour of different solids.     

Statistical analysis of the brittle fracture of sintered tungsten

A Weibull analysis was applied to the fracture data of sintered tungsten round bar specimens. Fracture data were obtained by performing flexural and tensile tests on these components. Two quantities were obtained which characterized the material variability and strength for each test method. The correlation between these quantities for the two test methods was found to be close.Nomenclature C least square line intercept - P _f failure probability - P _f ⁱ experimental failure probability - V specimen volume - W applied load - X horizontal coordinate of least square line - Y vertical coordinate of least square line - d specimen diameter - L distance between supporting knife edges - m Weibull modulus - v unit volume - stress - ₀ normalizing stress - _fV failure stress of specimen - _fv unit volume failure stress of specimen - _fv ^B unit volume failure stress in bending - ⁱ experimental stress - gamma function     

On the measurement and physical meaning of the cleavage fracture stress in steel

Elastic-plastic two-dimensional (2D) and three-dimensional (3D) finite element models (FEM) are used to analyze the stress distributions ahead of notches of four-point bending (4PB) and three-point bending (3PB) specimens with various sizes of a C-Mn steel. By accurately measuring the location of the cleavage initiation sites, the local cleavage fracture stress _f and the macroscopic cleavage fracture stress _F is accurately measured. The _f and _F measured by 2D FEM are higher than that by 3D FEM. _f values are lower than the _F, and the _f values could be predicted by _f=(0.8––1.0)_F. With increasing specimen sizes (W,B and a) and specimen widths (B) and changing loading methods (4PB and 3PB), the fracture load P _f changes considerably, but the _F and _f remain nearly constant. The stable lower boundary _F and _f values could be obtained by using notched specimens with sizes larger than the Griffiths–Owen specimen. The local cleavage fracture stress _f could be accurately used in the analysis of fracture micromechanism, and to characterize intrinsic toughness of steel. The macroscopic cleavage fracture stress _F is suggested to be a potential engineering parameter which can be used to assess fracture toughness of steel and to design engineering structure.     

Methodology for the determination of the interfacial properties of brittle matrix composites

The interfacial properties of a glass-ceramic matrix composite (SiC/CAS) were determined from single-fibre push-out tests using the interfacial test system. The coefficient of friction, , the residual clamping stress, _c, and fibre axial residual stress, _z , were extracted by fitting the experimental stress versus fibre-end displacement curves using the models of Hsueh, and Kerans and Parthasarathy. Using Hsueh's model, the intrinsic interfacial frictional stress (=_c) was found to be 11.1±3.2 MPa, whereas by using Kerans-Parthasarathy's model it was found to be 8.2±1.5 MPa. Comparisons between these models are included, together with a discussion of data analysis techniques.Nomenclature _z Axial fibre residual stress (Pa) - ^* Effective clamping stress (Pa) - _c Residual clamping stress (Pa) - _p Poisson's effect-induced clamping stress (Pa) - _d ⁰ Debond stress in the absence of residual stresses (Pa) - _d Experimental debond stress (Pa) - Compressive applied stress (Pa) - Interfacial shear stress (Pa) - u Fibre-end displacement (m) - h Debond length (m) - r Fibre radius (m) - E _f Fibre Young's modulus (Pa) - E _m Matrix Young's modulus (Pa) - v _f Fibre Poisson's ratio (dimensionless) - v _m Matrix Poisson's ratio (dimensionless) - f Fibre volume fraction (dimensionless) - k Parameter (dimensionless) - D Parameter (dimensionless) - Interfacial coefficient of friction (dimensionless) - G _i Interface toughness (J m^–2) - C _m Load-train compliance (m N^–1)     

Fatigue of metallic glasses

The fatigue behaviour of Ni₄₉Fe₂₉P₁₄B₆Si₂, Ni₄₈Fe₂₉P₁₄B₆Al₃ and Pd_77.5Cu₆Si_16.5 metallic glasses is examined. In the finite lifetime regime the relationship between stress amplitude ( _a), fracture stress ( _f), mean stress ( _m) and cycles to failure (N _f) is _a=A( _f–_m) (2N _f) ^b , whereA andb are 16.9 and –0.40 respectively for reduced gauge section Ni₄₉ strips (for _m 140 kg mm^–2) and 27.0 and –0.44 for Pd base wires. These results are unusual in thatA 1. Consequently, a sharp discontinuity exists near _a( _f– _m) –1. In a simple tensile test failure occurs at _f(=_y) and 2N_f=1; for peak stresses only a percent or so less than _f the sample will withstand hundreds of cycles of stress. For uniform cross-section glassy metal filaments, a fatigue limit is observed at stress ratios ( _a/ _f) in the vicinity of 0.07 to 0.15. The fatigue limit for reduced section specimens is a factor of 2 higher. Fatigue failure of the Ni-Fe strips may occur under partially or fully plane stress or plane strain conditions, depending on sample thickness and stress. Final failure of the Pd_77.5Cu₆Si_16.5 wires always occurs by general yielding of the remaining section.     

Crack-tip damaged zones in rubber-toughened amorphous polymers: a micromechanical model

The various stages of crack propagation in rubber-toughened amorphous polymers (onset and arrest, stable and unstable growth) are governed by the rate of energy dissipation in the cracktip damaged zone; hence the relationship between the applied stress intensity factorK ₁ and the damaged zone size is of utmost importance. The size of the crack-tip damaged zone has been related toK ₁ via a parameter which is characteristic of the material in given conditions: this factor is proportional to the threshold stress for damage initiation in a triaxial stress field, and has been denoted by ^*. Theoretical values of ^* have been calculated by means of a micromechanical model involving the derivation of the stresses near the particles and the application of damage initiation criteria. The morphology, average size and volume fraction of the rubbery particles have been taken into account together with the nature of the matrix. The calculated values of ^* have been successfully compared with the experimental ones, for a wide set of high-impact polystyrenes (HIPS) and rubber-toughened poly(methyl methacrylate) (RTPMMA).Nomenclature PS; HIPS polystyrene; high-impact polystyrene - PMMA; RTPMMA poly(methyl methacrylate); rubber-toughened PMMA - MI; CS/H; CS/R particle morphologies (multiple inclusion; hard core - rubber shell; rubber core - rigid shell) - K _r;K _g bulk moduli of rubber and glassy materials - G _r;G _g shear moduli of the same materials - v _p particle volume fraction - L mean centre-to-centre distance between neighbouring particles - B; H; W standard names for the dimensions of the compact tension specimen - R _y size of the crack-tip plastic zone in a homogeneous material - h half thickness of the crack-tip damaged zone - r; polar coordinates around the crack tip (Fig. 1) - r;r _p distance from particle centre; particle radius - p normalized distance from the particle (Equation 5) - K ₁;K _1c;K _1p stress intensity factor; critical values ofK ₁ at the onset of and during crack growth - G _1c plane strain energy release rate - _y yield stress in uniaxial tension - _th macroscopic threshold stress for the onset of local damage initiation in a composite material - ^* characteristic parameter (Equation 3) - ⁰; ₁ ⁰ ; ₂ ⁰ ; ₃ ⁰ applied stress tensor and its three principal stresses - ⁰ uniaxial applied stress - ; ₁; ₂; ₃ local stress tensor and its three principal stresses - A tensor which elements are the ratios of those of over those of ⁰ (Equation 4) - v Poisson's coefficient of the matrix - g triaxiality factor of the crack-tip stress field - _e; _p Mises equivalent stress; dilatational stress (negative pressure) - I ₁;I ₂ invariants of the stress tensor - U ₁;U ₂ material parameters for argon and Hannoosh's craze initiation criterion (Equation 12)     

Absence of Phase-Fluctuation Contribution to the Low-Frequency Optical Conductivity in d-Wave Superconductors at Zero Temperature

The behavior of the low-frequency optical conductivity _reg() in superconducting cuprates is, at the present, an open and interesting issue. In particular, since the zero-temperature and zero-frequency limit of _reg() attains a value much larger than the universal value expected within a self-consistent T-matrix calculation, an intriguing possibility is that the collective mode can also contribute to _reg(). By taking into account the effect of dissipation on the collective mode in a d-wave superconductor, we evaluate the phase-fluctuation contribution to _reg(0) within the formalism of the phase-only action. We show that even though the collective mode contributes to _reg() at finite frequencies, approaching the zero-temperature and zero-frequency regime the corrections at _reg() due to phase fluctuations vanish.     

Stress-strain behaviour of nitrogen bearing austenitic stainless steels in the temperature range 298–473 K

The stress-strain behaviour of three nitrogen-bearing low-nickel austenitic stainless steels has been investigated via a series of tensile tests in the temperature range 298–473 K at an initial strain rate of 1.6×10^–5s^–1. Experimental stress-strain data were analysed employing Rosenbrock's minimization technique in terms of constitutive equations proposed by Hollomon, Ludwik, Voce and Ludwigson. Ludwigson's equation has been found to describe the flow behaviour accurately, followed by Voce's equation. The resultant strain-hardening parameters were analysed in terms of variations in temperature. A linear relationship between ultimate tensile stress and the Ludwigson parameters has been established. The influence of nitrogen on the Ludwigson modelling parameters has also been explained.Nomenclature True stress - _t True strain - _f True fracture strain - Strain rate - T Temperature - K _H, n _H Hollomon parameters - K _L, n _L Ludwik parameters - K _1L, k _2L, n _1L, n _2L Ludwigson parameters - _s, K _V, n _V Voce parameters - _{u relation} Uniform strain computed from a particular relation - _L Transient strain - ₀ Flow stress at zero plastic strain (Ludwik) - _L Transient stress - _y Yield stress - _u Ultimate tensile stress     

Electrical conductivity,thermoelectric power and dielectric constant of NiWO4

The a.c. electrical conductivity ( _ac), thermoelectric power () and dielectric constant () of antiferromagnetic NiWO₄ are presented. _ac and have been measured in the temperature range 300 to 1000 K and in the temperature range 600 to 1000 K. Conductivity data are interpreted in the light of band theory of solids. The compound obeys the exponential law of conductivity = ₀ exp (–W/kT). Activation energy has been estimated as 0.75eV. The conductivity result is summarized in the following equation =2.86 exp (–0.75 eV/kT)^–1 cm^–1 in the intrinsic region. The material is p-type below 660 K and above 950 K, and is n-type between 660 and 950 K.     

Carbon fibre-reinforced cement

This review describes fabrication processes for aligned fibre and random fibre carbonreinforced cement and links important process parameters with composite theory. The way in which the material fits into the general framework of crack constraint and matrix cracking theories is discussed. A broad survey is made of the mechanical properties, durability and dimensional stability of a variety of carbon-reinforced cement composites, and economic constraints on potential applications are considered.List of symbols b breadth of three-point bend specimen - d depth of three-point bend specimen - E _c composite Young's modulus - E _f fibre Young's modulus - E _m matrix Young's modulus - l fibre length - l _c fibre critical transfer length - l _s specimen span in three-point bend test - m Weibull modulus - r fibre radius - P applied load - V _f fibre volume fraction - V _m matrix volume fraction - x length of fibre needed to transfer load _mu V _m - x _d crack spacing in a composite with short, aligned fibres - _fu fibre ultimate strain - _mu matrix ultimate strain - _fu fibre ultimate strength - _mu matrix ultimate strength - _cu composite ultimate strength - _MOR modulus of rupture - _T tensile strength - interlaminar shear strength - _i interfacial shear strength - _m matrix work of fracture - _F work of fracture     

Isochoric Heat Capacity Measurements for 2,2-Dichloro-1,1,1-Trifluoroethane (R123) at Temperatures from 167 to 341 K and 1-Chloro-1,2,2,2-Tetrafluoroethane (R124) from 94 to 341 K at Pressures to 35 MPa

Molar heat capacities at a constant volume (C _v) of 2,2-dichloro-1,1,1-trifluoroethane (R123) and 1-chloro-1,2,2,2-tetrafluoroethane (R124) were measured with an adiabatic calorimeter. Temperatures ranged from 167 K for R123 and from 94 K for R124 to 341 K, and pressures were up to 33 MPa. Measurements were conducted on the liquid in equilibrium with its vapor and on compressed liquid samples. The samples were of a high purity, verified by chemical analysis of each fluid. For the samples, calorimetric results were obtained for two-phase (C ⁽²⁾ _v), saturated liquid (C or C _x ), and single-phase (C _v) molar heat capacities. The C data were used to estimate vapor pressures for values less than 100 kPa by applying a thermodynamic relationship between the saturated liquid heat capacity and the temperature derivatives of the vapor pressure. Due to the tendency of both R123 and R124 to subcool, the triple-point temperature (T _tr) and the enthalpy of fusion ( _fus H) could not be measured. The principal sources of uncertainty are the temperature rise measurement and the change-of-volume work adjustment. The expanded uncertainty (at the 2 level) for C _v is estimated to be 0.7%, for C ⁽²⁾ _v it is 0.5%, and for C it is 0.7%.     

Surface Tension and Density of Oxygen-Free Liquid Aluminum at High Temperature

New values of densities and surface tensions of liquid aluminum obtained in the range 1600 to 2360 K by contactless techniques in neutral gases are reported. Conditions for oxygen-free aluminum are fulfilled which allow determination of the surface tension of aluminum. Extrapolation to the melting point, T _m = 933 K, confirms the value of (T = 933K) = 1.05 N m^–1.     

Application of a new iterative method for elastic-plastic stress analysis

A new iterative method for elastic-plastic stress analysis based on a new approximation of the constitutive equations is proposed and compared with standard methods on the accuracy and the computational time in a test problem. The proposed method appears to be better than the conventional methods on the accuracy and comparable with others on the computational time. Also the present method is applied to a crack problem and the results are compared with experimental ones. The agreement of both results are satisfactory.List of symbols u = (u ₁, u ₂) displacements u ^(H) = u ⁽ⁿ⁺¹⁾ - u ⁽ⁿ⁾ u _k ⁽ⁿ⁾ = u _(k ^{(n + 1)} - u ⁽ⁿ⁾ (n, k = 0, 1, 2, ...) - = ₁₁, ₂₂, ₁₂) stresses - = (₁₁, ₂₂, ₁₂) strains - = (₁₁, ₂₂, ₁₂) center of yield surface - D elastic coeffficient matrix, C = D ^–1 - von Mises yield function. The initial yielding is given by f() = _Y - f {f/} - ^* transposed f - H hardening parameter (assumed to be a positive constant for kinematic hardening problems) - time derivative of - [K] total elastic stiffness matrix - T traction vector - = [B] relation between nodal displacements and strains     

Size effect on the strength of glassy carbon

Three-point bend tests were conducted on three sets of commercial glassy carbon specimens having volumes of V, 2V, and 4V, and mean strengths of these specimens decreased with increasing volume (from 37 to 32 to 28×10³ psi). These results are in good agreement with Weibull predictions of (V)=1.12(2V)=1.26(4V), which are based on a uniform distribution of flaws throughout a volume of material that is characterized by a Weibull modulus of m=6.0. Moreover, the resulting strength formulation for any volume V(in.³), =6 V ^–1/6×10³ psi, correlates well with widerspread data from other sources. In common with other brittle materials, glassy carbon satisfies the crack bifurcation relationship of r ^1/2=constant, and this was used to provide additional support for the validity of the volume-dependent Weibull theory. Failures in this material usually originated at interior spherical pores, and the mean size of these flaws for different sets of specimens increased with test volume.     

Plastic instability related to grain-boundary failure in an Al-Zn-Mg alloy at low temperatures

The strength and ductility of an Al-6 wt % Zn-1.2 wt % Mg alloy at low temperatures have been investigated by varying the grain size, the amount of grain-boundary precipitate and the nature of the precipitates in the matrix. Pronounced grain-boundary embrittlement has been observed at temperatures below — 100° C in alloys age-hardened by GP zones and especially in coarse-grained alloy specimens, but was not observed in over-aged specimens. From the condition for plastic instability related to the grain-boundary micro-cracking, the temperature and structure dependences of the ultimate tensile properties are expressed by; ( _i – _o)/_i= _u/n + C, where _i is the instability stress (true ultimate tensile strength), ₀ the 0.2% proof stress, _u the uniform elongation, n a constant found to be about 1/2 and C a constant related to the work-hardening rate of the matrix.     

Transient thermal stress analysis of multilayered hollow cylinder

Summary This paper deals with the transient response of one-dimensional axisymmetric quasistatic coupled thermoelastic problems. Laplace transform and finite difference methods are used to analyze the problems. Using the Laplace transform with respect to time, the general solutions of the governing equations are obtained in the transform domain. The solution is obtained by using the matrix similarity transformation and inverse Laplace transform. We obtain solutions for the temperature and thermal stress distribution in a transient state. Moreover, the computational procedures established in this article can solve the generalized thermoelasticity problem for a multilayered hollow cylinder with orthotropic material properties.Nomenclature Lame's constant - density - C _v specific heat - k _r ,k radial and circumferential thermal conductivity - _r , linear radial and circumferential thermal expansion coefficient - E _r ,E radial and circumferential Young's modulus - v _r Poisson's ratio - ₀ reference temperature - ,T dimensional and nondimensional temperature - r ^*,r dimensional and nondimensional radial coordinate - ,t dimensional and nondimensional time - _r ^* , _r dimensional and nondimensional radial stress - ^* , dimensional and nondimensional circumferential stress - U, u dimensional and nondimensional radial component of displacement     

Effect of magnesium content on the stress exponent and effective stress in the steady state creep of Al-Mg alloys

The stress exponent of steady state creep,n, and the internal ( _i) and effective stresses ( _e) have been determined using the strain transient dip test for a series of polycrystalline Al-Mg alloys creep tested at 300° C and compared with previously published data. The internal or dislocation back stress, _i, varied with applied stress,, but was insensitive to magnesium content of the alloy, being represented by the empirical equation _i=1.084 ^1.802. Such an applied stress dependence of _i can be explained by using an equation for _i of the form _i (dislocation density)^1/2 and published values for the stress dependence of dislocation density. Values of the friction stress, _f, derived using the equation _e/=(1–c) (1– _f/), indicate that _f is not dependent on the magnesium content. A constant value of _f can best be rationalized by postulating that the creep dislocation structure is relatively insensitive to the magnesium content of the alloy.On leave from Engineering Materials Department, University of Windsor, Windsor, Ontario N9B 3P4, Canada.     

Thermal diffusivity of inhomogeneous systems

The possibility of analyzing the nonsteady temperature fields of inhomogeneous systems using the quasi-homogeneous-body model is investigated.Notation t, t_I, t_i temperature of quasi-homogeneous body inhomogeneous system, and i-th component of system - a, , c thermal diffusivity and conductivity and volume specific heat of quasi-homogeneous body - a_{i i}, c_i same quantities for the i-th component - q heat flux - S, V system surface and volume - x, y coordinates - macrodimension of system - dimensionless temperature Fo=a/² - Bi=/ Fourier and Biot numbers - N number of plates - =h/ ratio of micro- and macrodimensions - _V, volumeaveraged and mean-square error of dimensionless-temperature determination - time - m_i i-th component concentration Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 39, No. 1, pp. 126–133, July, 1980.