An isolated bridgeless AC-DC PFC converter using a LC resonant voltage doubler rectifier

This paper proposed an isolated bridgeless AC–DC power factor correction (PFC) converter using a LC resonant voltage doubler rectifier. The proposed converter is based on isolated conventional single-ended primary inductance converter (SEPIC) PFC converter. The conduction loss of rectification is reduced than a conventional one because the proposed converter is designed to eliminate a full-bridge rectifier at an input stage. Moreover, for zero-current switching (ZCS) operation and low voltage stresses of output diodes, the secondary of the proposed converter is designed as voltage doubler with a LC resonant tank. Additionally, an input–output electrical isolation is provided for safety standard. In conclusion, high power factor is achieved and efficiency is improved. The operational principles, steady-state analysis and design equations of the proposed converter are described in detail. Experimental results from a 60 W prototype at a constant switching frequency 100 kHz are presented to verify the performance of the proposed converter.     

Power factor correction converter using delay control

A low cost universal input voltage single-controller power factor correction converter for a 200 W power supply is proposed. It consists of the PFC part followed by a DC-DC converter as in a conventional two-stage scheme. However a single PWM controller is used as in a single-stage PFC scheme. The switch in the PFC part is synchronized with the switch in the DC-DC converter and has a fixed frequency. Employing an adaptive delay scheme, the PPC switch is controlled to limit the capacitor voltage within a desired range for optimum efficiency and to reduce input current harmonic distortion. The design procedures of the delay scheme, the feedback loop, and experimented results are presented to verify the performance     

Reduced conduction loss zero-voltage-transition power factorcorrection converter with low cost

A new low conduction loss low-cost zero-voltage-transition (ZVT) power factor correction converter (PFC) is presented. The conventional PFC, which consists of a bridge diode rectifier and a boost converter (one active switch), always has three semiconductor conduction drops. The two-switch-type PFC, which was presented recently, reduces conduction loss by reducing one conduction drop, but the cost is increased because of one additional switch. The proposed PFC reduces conduction loss with one switch. Conduction loss reduction is a little bit less than that of the two-switch type, but it is achieved with low cost. Operation, features, and characteristics are comparatively illustrated and verified by the experimental results from a 2.5-kW 100-kHz laboratory prototype     

中大功率单相功率因数校正器的设计与实现

采用有源功率因数校正技术(active power factor correction,APFC)设计并实现了一款高功率因数、高效率、低谐波、低噪声的"绿色"功率因数校正装置.1700 W样机实验结果表明:所设计的功率因数校正装置能在165～275 V AC宽电压范围内,得到稳定的直流电压输出;输入交流电流能很好的跟踪...     

A high-efficiency single-stage single-switch high-power-factorAC/DC converter with universal input

A single-stage single-switch power-factor-correction (PFC) AC/DC converter with universal input is presented in this paper. The PFC can be achieved based upon the charge-pump concept, and the PFC stage operates in the continuous current mode (CCM). The switch has less current and voltage stresses over a wide range of load variation so that a low-voltage rating device can be used. The presented converter features high power factor, high efficiency, and low cost. An 80-W prototype was implemented to show that it has 85% efficiency with low-voltage stress from 0.5% to 100% load variation over universal line input     

A High-Quality Rectifier Based on Sheppard–Taylor Converter Operating in Discontinuous Capacitor Voltage Mode

This paper presents a single-phase soft-switched high power factor (PF) Sheppard-Taylor rectifier suitable for applications requiring low-voltage and high-current output. The proposed rectifier is designed to operate at discontinuous capacitor voltage mode. The Sheppard-Taylor converter in this mode of operation provides zero-voltage turnoff switching, as well as natural input PF correction over a wide range of input voltage, which makes the converter suitable for universal input applications. Due to its simplified control circuitry and reduced switch current stress, this converter presents better efficiency and higher reliability. In addition, the presented converter features continuous input-output currents, which result in low electromagnetic interference emission. Principle of operation, theoretical analysis, and experimental results from a laboratory prototype rated at 45 W/10 Vdc output voltage are presented. The measured efficiency and total harmonic distortion of the input line current were 85% and 3.2%, respectively. The input current harmonics meet the EN61000-3-2 Class D requirements.     

A soft-switching mode rectifier with power factor correction andhigh frequency transformer link

This paper presents a soft-switching mode rectifier (SSMR) consisting of a power factor correction zero-voltage-transition-pulse-width-modulated (PFC ZVT-PWM) converter and a high-frequency transformer-coupled DC/DC zero voltage switching clamped voltage (ZVS-CV) converter. An easily implemented ZVT soft-switching mechanism is developed to reduce the switching losses and stresses of the power switches in the PFC ZVT-PWM converter. The operations of the proposed SSMR in various modes are analyzed in detail and the associated governed equations are derived. Then accordingly, a quantitative design procedure is developed to find the values of soft-switching circuit components. In the control aspect, the dynamic model of the SSMR is derived and a current waveform controller is designed, such that sinusoidal line current with low harmonics and near unity power factor is obtained. Under this condition, a voltage controller is also designed for yielding good DC output voltage control characteristics. Validity of the designed SSMR is verified experimentally     

新型三相单开关功率因数校正器的研究

为解决传统三相单开关功率因数校正器输入电流谐波较大的问题,设计了一种新型拓扑结构的三相单开关升压型PFC(Power Factor Correction)电路。通过在Boost电感和整流桥之间插入合适电容构成二阶滤波器,虽然控制算法不变,但可以在保证功率因数不变的前提下优化输入电流THD（Total Harmonic Distortion）。基于对电路原理的简要分析,建立Matlab仿真模型,再以TMS320F28335为控制核心,搭建Boost PFC 变换器的实验平台。仿真和实验均表明该方案可行,实验电路测试的输入电流THD值小于10%,具有实际应用价值。     

一种改进的ZCT无桥功率因数校正电路设计

为了降低开关损耗,提高变换器的效率,提出了一种改进的零电流转化软开关无桥功率因数校正电路,实现了变换器主开关管和辅助开关管的零电流导通和零电流关断,有效地减小了导通损耗,提高了电路的效率。详细分析了电路的工作模态、工作条件和主开关管的导通损耗。仿真和实验结果表明,该功率因数校正电路实现了输入电流对输入电压的良好跟踪,功率因数高,谐波含量少,效率较传统的全桥功率因数校正电路有明显的提高。 关键词：全桥;零电流转换;无桥;功率因数校正     

A digitally controlled switch mode power supply based on matrix converter

High power telecommunication power supply systems consist of a three-phase switch mode rectifier followed by a dc/dc converter to supply loads at -48 V dc. These rectifiers draw significant harmonic currents from the utility, resulting in poor input power factor with high total harmonic distortion (THD). In this paper, a digitally controlled three-phase switch mode power supply based on a matrix converter is proposed for telecommunication applications. In the proposed approach, the matrix converter directly converts the low frequency (50/60Hz, three-phase) input to a high frequency (10/20kHz, one-phase) ac output without a dc-link. The output of the matrix converter is then processed via a high frequency isolation transformer to produce -48V dc. Digital control of the system ensures that the output voltage is regulated and the input currents are of high quality under varying load conditions. Due to the absence of dc-link electrolytic capacitors, power density of the proposed rectifier is expected to be higher. Analysis, design example and experimental results are presented from a three-phase 208-V, 1.5-kW laboratory prototype converter.     

Low-harmonic GTO converter for fundamental power factorcompensation

A low-harmonic GTO (gate turn-off) thyristor AC-to-DC converter with line current lead-lag phase shift control ability is proposed and analyzed. The converter can be used either as a low-harmonic GTO-controlled rectifier or a fundamental input power factor compensator in a power supply system. The effect of PWM (pulse width modulation) current phase number on the harmonic contents and converter output voltage control range is investigated. Lower order input current harmonics are eliminated over a wide range, using a specially designed PWM current pattern. The effect of the PWM current pulse number on the power factor compensation characteristic is investigated     

A simple and effective method to alleviate the rectifierreverse-recovery problem in continuous-current-mode boostconverters

Rectifier reverse-recovery problems cause a significant efficiency reduction as well as severe electromagnetic interference (EMI) in continuous-current-mode (CCM) boost converters. To alleviate these problems, this paper presents a simple and effective solution that involves shifting the original rectifier current to a new branch, which consists of a rectifier and a coupled winding of the boost inductor. When the active switch turns on, the current through the original boost rectifier is zero and the current decrease rate di/dt in the new branch is controlled by the leakage inductor. Based on the operation analysis, design issues to guarantee complete current shift are also addressed. Applying the proposed concept to a 500 W CCM DC/DC boost converter and a 500 W CCM power factor correction (PFC) boost converter with universal-line input generates a 2% efficiency improvement. The same concept can be easily extended to other basic DC/DC and CCM PFC converters     

A single-stage fast regulator with PFC based on an asymmetrical half-bridge topology

This work presents single-stage regulators with power-factor correction (PFC) based on an asymmetrical half-bridge topology. The proposed regulator is formed from a boost converter with two coupled inductors and an asymmetrical half-bridge converter with the synchronous switch technique, and it is controlled with pulsewidth modulation to achieve zero-voltage switching (ZVS). The boost converter is operated in discontinues conduction mode to achieve PFC. With the coupled inductors, input current ripple and power factor can be improved significantly. The proposed regulator has the features of constant-frequency operation, ZVS, and low voltage stress imposed on the active switches. Moreover, the regulator can achieve high power factor, high power density, high efficiency, low switching loss, and low component count, which makes its applications at medium-power levels feasible. Experimental results have verified the discussed features of the proposed regulator.     

A robust low quiescent current power receiver for inductive power transmission in bio implants

In this paper, a robust low quiescent current complementary metal-oxide semiconductor (CMOS) power receiver for wireless power transmission is presented. This power receiver consists of three main parts including rectifier, switch capacitor DC–DC converter and low-dropout regulator (LDO) without output capacitor. The switch capacitor DC–DC converter has variable conversion ratios and synchronous controller that lets the DC–DC converter to switch among five different conversion ratios to prevent output voltage drop and LDO regulator efficiency reduction. For all ranges of output current (0–10 mA), the voltage regulator is compensated and is stable. Voltage regulator stabilisation does not need the off-chip capacitor. In addition, a novel adaptive biasing frequency compensation method for low dropout voltage regulator is proposed in this paper. This method provides essential minimum current for compensation and reduces the quiescent current more effectively. The power receiver was designed in a 180-nm industrial CMOS technology, and the voltage range of the input is from 0.8 to 2 V, while the voltage range of the output is from 1.2 to 1.75 V, with a maximum load current of 10 mA, the unregulated efficiency of 79.2%, and the regulated efficiency of 64.4%.     

A single-stage quasi-resonant flyback converter using a synchronous rectifier

A single-stage quasi-resonant flyback converter using the synchronous rectifier (SR) is proposed for improving power factor and system efficiency. This converter operates at the critical conduction mode with the variable frequency (VF) control to reduce the switching loss of the primary switch. The bulk capacitor voltage can be independent of the output load and kept within a practical range for the universal line input. Therefore, the problem of high-voltage stress across the bulk capacitor is reduced. The proposed converter features relatively low bulk capacitor voltage in the universal line voltage and also complies with the Standard IEC 61000-3-2 Class D limits. Moreover, since it uses the voltage-driven SR, it achieves a high efficiency. The operational principle and theoretical analysis are presented. Experimental results for a 100?W (19?V/5.3?A) adapter at the VF were obtained to show the performance of the proposed converter.     

Novel zero-voltage-transition current-fed full-bridge PWM converterfor single-stage power factor correction

A novel zero-voltage-transition (ZVT) current-fed full-bridge pulsewidth modulation (PWM) power converter for single-stage power factor correction (PFC) is presented to improve the performance of the previously presented ZVT converter. A simple auxiliary circuit which includes only one active switch provides a zero-voltage-switching (ZVS) condition to all semiconductor devices (two active switches are required for the previous ZVT converter). This leads to reduced cost and a simplified control circuit compared to the previous ZVT converter. The ZVS is achieved for wide line and load ranges with minimum device voltage and current stresses. Operation principle, control strategy and features of the proposed power converter are presented and verified by the experimental results from a 1.5 kW 100 kHz laboratory prototype     

Analysis and design of a low-stress buck-boost converter in universal-input PFC applications

In converters for power-factor-correction (PFC), the universal-input capability, i.e., the ability to operate from any ac line voltage world-wide, comes with a heavy penalty in terms of component stresses and losses, and with restrictions on the dc output voltage. In this paper, we propose a new two-switch topology, boost-interleaved buck-boost (BoIBB) converter, which can offer significant performance improvements over single-switch buck-boost converters (including flyback, SEPIC, or Cuk topologies) or other two-switch buck-boost converters in universal-input PFC applications. The paper presents an analysis of the converter operation and component stresses, as well as design guidelines. High efficiency (over 93%) throughout the universal-input ac line voltage range is demonstrated on an experimental 100-W, 200-V dc output, universal-input BOIBB PFC rectifier.     

Improved control strategy on single-phase buck-type power factor correction converter

A buck-type power factor correction (PFC) converter is not only effectively capable of eliminating utility input current harmonics; its related characteristics also include high efficiency, absence of inrush current, capability of obtaining low dc output voltage, ability to protect against short circuit, and so forth. On the other hand, because this type of rectifier must employ inductors design for high inductance, the buck-type PFC converter tends to increase the volumetric size and weight, and this has prevented its widespread use. This paper presents a new control strategy for this type of converter which can reduce the size and weight of the inductor and also eliminate the ripple components included in the output voltage waveform. The operating principle, simulation and experimental results obtained by a prototype rectifier are described.     

Implementation of zero current switch turn-ON based buck-boost-buck type rectifier for low power applications

A single-stage single-switch AC–DC integrated converter is proposed in this paper, as a tight DC voltage regulator with unity input power factor for the fundamental component of the input current. Proposed converter is formed by the integration of buck-boost configuration with a buck converter operated by a single switch. The buck-boost section of the proposed configuration is operated in current discontinuous conduction mode (DCM) to get unity input power factor at the supply terminals and the buck section is operated up to boundary current conduction mode (BCM). The features acquired by the converter operating in complete discontinuous conduction mode (DCM) are unity input power factor, zero-current turn-ON for the Switch, fast and good DC output voltage regulation with extensive conversion range and low voltage stress on the switch. Additionally, the intermediate capacitor voltage stress is independent of converter load variations and so the switch also is subjected to constant peak voltage stress. A comprehensive study is carried out to obtain the necessary design equations. A design model is implemented using simulation and hardware. The results confirm the performance of the proposed configuration.     

A zero voltage transition boost converter employing a soft switching auxiliary circuit with reduced conduction losses

This paper presents a zero-voltage-transition (ZVT) boost converter using a soft switching auxiliary circuit for power factor correction (PFC) applications. The improvement over existing topologies lies in the positioning of the auxiliary circuit capacitors and the subsequent reduction in the resonant current and therefore the conduction losses as compared to other similar topologies. The proposed converter operates in two modes - Mode 1 and Mode 2. It is shown in the paper that the converter should be designed using the constraints obtained in Mode 1 to achieve low-loss switching. The converter is analyzed and characteristic curves presented which are then used in a detailed design example. Experimental results from a 250 W, 127 V input laboratory prototype switching at 100 kHz verify the design process and highlight the advantages of the proposed topology. The proposed converter is suitable for single-phase, two stage power factor correction circuits with universal input voltage range and power levels up to 3 kW.