Blend of sharpness and strength on a ball nose endmill geometry for high speed machining of Ti6Al4V

The applications of titanium alloys are increasingly common at marine, aerospace, bio-medical and precision engineering due to its high strength to weight ratio and high temperature-withstanding properties. However, whilst machining the titanium alloys using the solid carbide tools, even with application of high pressure coolant, reduced tool life was widely reported. The generation of high temperatures at the tool–work interface causes adhesion of work material on the cutting edges, and hence, shorter tool life was reported. In order to reduce the high tool–work interface temperature-positive rake angle, higher primary relief and higher secondary relief were configured on the ball nose endmill cutting edges. Despite of careful consideration of tool geometry, after an initial working period, the growth of flank wear accelerates the high cutting forces followed by work material adhesion on the cutting edges. Hence, it is important to blend the strength, sharpness, geometry and surface integrity on the cutting edges so that the ball nose endmill would exhibit an extended tool life. This paper illustrates the effect of ball nose endmill geometry on high speed machining of Ti6Al4V. Three different ball nose endmill geometries were configured, and high speed machining experiments were conducted to study the influence of cutting tool geometry on the metal cutting mechanism of Ti-6Al-4V alloy. The high speed machining results predominantly emphasize the significance of cutting edge features such as K-land, rake angle and cutting edge radius. The ball nose endmills featured with a short negative rake angle of value ?5° for 0.05～0.06 mm, i.e. K-land followed by positive rake angle of value 8°, has produced lower cutting forces signatures for Ti-6Al-4V alloy.     

Effect of tool stiffness upon tool wear in high spindle speed milling using small ball end mill

Longer tool life can be tentatively achieved at a higher feed rate using a small ball end mill in high spindle speed milling (over several tens of thousands of revolutions per minute), although the mechanism by which tool life is improved has not yet been clarified. In the present paper, the mechanism of tool wear is investigated with respect to the deviation in cutting force and the deflection of a ball end mill with two cutting edges. The vector loci of the cutting forces are shown to correlate strongly with wear on both cutting edges of ball end mills having various tool stiffnesses related to the tool length. The results clarified that tool life can be prolonged by reducing tool stiffness, because the cutting forces are balanced, resulting in even tool wear on both cutting edges as tool stiffness is lowered to almost the breakage limit of the end mill. A ball end mill with an optimal tool length showed significant improvement in tool life in the milling of forging die models.     

The effect of cutting parameters and cutting tools on machining performance of carbon graphite material

Abstract

The present study focuses on the effects of cutting speed, feed rate and cutting tool material on the machining performance of carbon graphite material. Polycrystalline Diamond (PCD) cutting tools are used in machining experiments and its performance is compared with the tungsten carbide (WC) and Cubic Boron Nitride (CBN) tools. Machining performance criteria such as flank and nose wear and resulting surface topography and roughness of machined parts were studied. This study illustrates that feed rate and cutting tool material play a dominant role in the progressive wear of the cutting tool. The highest feed rate and cutting speed profoundly reduce the tool wear progression. The surface roughness and topography of specimens are remarkably influenced from the tool wear. Major differences are found in the wear mechanisms of PCD and WC and CBN cutting tools.     

Determining the cutting conditions for sculptured surface machining

This paper deals with a new method for determining cutting conditions for the machining of 3D sculptured surface shapes with a ball endmill. Since the interaction area between workpiece and cutting tool changes during ball endmill machining, the cutting conditions have to be changed accordingly. To determine the spindle speed, the tool-workpiece contact area is obtained from the depth of cut, path interval, and cutter contact (CC) data. The spindle speed is determined so that the tangential cutting speed of the centroid of the tool-workpiece contact area becomes the value suggested in the machining data handbook. The feedrate is determined so that the material removal rate is maximised within the range of the cutting-force constraint. The practical feasibility of the proposed scheme has been verified through experiments performed on a workpiece with sculptured surfaces. The test result shows that the new method can be used to increase the tool life, and improve the production rate.     

Machining performance of a grooved tool in dry machining Ti-6Al-4 V

In this paper, dry machining experiment of Ti-6Al-4 V was carried out to investigate the machining performance of a grooved tool in terms of its wear mechanisms and the effects of cutting parameters (cutting speed, feed rate, and cutting depth) on tool life and surface roughness of the machined workpiece. The results showed that chip-groove configuration substantially improved the machining performance of cutting tool. The main wear mechanisms of the grooved tool were adhesive wear, stripping wear, crater wear, and dissolution-diffusion wear. The resistance to chipping was enhanced due to the decrease of contact pressure of tool-chip interface. And the resistance to plastic deformation of tool nose was weakened at the cutting speed of more than 60 m/min. The appropriate cutting speed and feed rate were less than 70 m/min and 0.10 mm/r, respectively. With cutting speed increasing, the surface roughness of machined workpiece decreased. A high feed rate helped the formation of higher surface roughness except 0.21 mm/r. When cutting depth increased, tool nose curvature and phase transformation of workpiece material had great impact on surface roughness.     

Influence of machining parameters on the machinability of particulate reinforced Al/SiC–MMC

The paper presents the result of an experimental investigation on the machinability of silicon carbide particulate aluminium metal matrix composite during turning using a rhombic uncoated carbide tool. The influence of machining parameters, e.g. cutting speed, feed and depth of cut on the cutting force has been investigated. The influence of the length of machining and cutting time on the tool wear and the influence of various machining parameters, e.g. cutting speed, feed, depth of cut on the surface finish criteria has been analyzed through the various graphical representations. The combined effect of cutting speed and feed on the flank wear has also been investigated. The influence of cutting speed, feed and depth of cut on the tool wears and built-up edge is analyzed graphically. The job surface condition and wear of the cutting tool edge for the different sets of experiments have been examined and compared for searching out the suitable cutting condition for effective machining performance during turning of Al/SiC-MMC. Test results show that no built-up edge is formed during machining of Al/SiC-MMC at high speed and low depth of cut. From the test results and different SEM micrographs, suitable range of cutting speed, feed and depth of cut can be selected for proper machining of Al/SiC-MMC.     

Experimental investigations while hard machining of DIEVAR tool steel (50 HRC)

This paper describes hard machining which offers many potential benefits over traditional manufacturing techniques. In this work, investigations were carried out on end milling of hardened tool steel DIEVAR (hardness 50 HRC), a newly developed tool steel material used by tool- and die-making industries. The objective of the present investigation was to study the performance characteristics of machining parameters such as cutting speed, feed, depth of cut and width of cut with due consideration to multiple responses, i.e. volume of material removed, tool wear, tool life and surface finish. Performance evaluation of physical vapour deposition-coated carbide inserts, ball end mill cutter and polycrystalline cubic boron nitride inserts (PCBN) was done for rough and finish machining on the basis of flank wear, tool life, volume of material removed, surface roughness and chip formation. It has been observed from investigations that chipping, diffusion and adhesion were active tool wear mechanisms and saw-toothed chips were formed whilst machining DIEVAR hard steel. PCBN inserts give an excellent performance in terms of tool life and surface finish in comparison with carbide-coated inserts. End milling technique using PCBN inserts could be a viable alternative to grinding in comparison to ball end mill cutter in terms of surface finish and tool life.     

Analysis model of parameters affecting cutting performance in high-speed machining

Further progress in green cutting applications depends on the innovativeness of machine tools, advances in tool development, and, especially, more complex tool and cutting technologies. Therefore, this study analyzes the factors influencing high-speed cutting performance. Grey relational analysis and the Taguchi method are then incorporated in the experimental plan with high-speed milling of AISI H13 tool steel. Experimental results indicate that the contributions of tool grinding precision, geometric angle, and cutting conditions to the multiple quality characteristics of high-speed milling for AISI H13 tool steel are 11.75, 9.80, and 73.11 %, respectively. For rough machining, tool life and metal removal volume are the primary evaluation indicators and cutting parameters should be prioritized, especially cutting speed and feed per tooth. In finish machining, workpiece surface roughness is the primary evaluation indicator. Besides the selection of cutting parameters, the design and grinding of endmill are critical factors, especially the design and grinding of relief angles.     

Some studies on hard turning of AISI 4340 steel using multilayer coated carbide tool

Hard turning with multilayer coated carbide tool has several benefits over grinding process such as, reduction of processing costs, increased productivities and improved material properties. The objective was to establish a correlation between cutting parameters such as cutting speed, feed rate and depth of cut with machining force, power, specific cutting force, tool wear and surface roughness on work piece. In the present study, performance of multilayer hard coatings (TiC/TiCN/Al₂O₃) on cemented carbide substrate using chemical vapor deposition (CVD) for machining of hardened AISI 4340 steel was evaluated. An attempt has been made to analyze the effects of process parameters on machinability aspects using Taguchi technique. Response surface plots are generated for the study of interaction effects of cutting conditions on machinability factors. The correlations were established by multiple linear regression models. The linear regression models were validated using confirmation tests. The analysis of the result revealed that, the optimal combination of low feed rate and low depth of cut with high cutting speed is beneficial for reducing machining force. Higher values of feed rates are necessary to minimize the specific cutting force. The machining power and cutting tool wear increases almost linearly with increase in cutting speed and feed rate. The combination of low feed rate and high cutting speed is necessary for minimizing the surface roughness. Abrasion was the principle wear mechanism observed at all the cutting conditions.     

Use of Ceramic Tools in Hard Turning of Hardened AISI M2 Steel

Tool wear and machining performance of hardened AISI M2 steel in hard turning has been studied. Ceramic tools were used in the cutting tests without coolants, and the workpiece was heat treated to increase its hardness up to Re 60. Cutting forces, temperature, and tool wear were measured in the experiments and the effects of cutting conditions on these were investigated. Important aspects from the research are summarized as follows: 1. Flank wear was the dominant wear mode on the ceramic tool insert in hard turning. In contrast, crater wear was very small due to the ceramics high resistance against chemical reactions at high temperature. A notch was unlikely to be formed in the tool.

2. The initial flank wear rate mainly depends on the feed rate. High feed rates cause a high initial flank wear rate.

3. Depth of cut was the most important cutting parameter to affect cutting force variation, and the cutting force increased due to tool wear.

     

硬车削滚动轴承套圈的试验研究

针对滚动轴承套圈硬车削加工过程中表面质量存在的问题,对硬车削过程中切削用量和刀具参数对表面粗糙度的影响进行了研究,采用CBN刀具进行了6205滚动轴承套圈的硬车削加工试验,将进给量、切削速度、切削深度和刀尖圆弧半径作为试验因子,通过正交试验分析了它们对零件加工后表面粗糙度的影响规律,并归纳出了该试验范围内的最佳切削用量和刀具参数组合。研究结果表明,进给量对表面粗糙度的影响最大,刀尖圆弧半径对表面粗糙度的影响次之,切削速度对表面粗糙度的有一定影响,切削深度对表面粗糙度的影响非常小。     

铁基粉末冶金材料的高速干切削试验研究

用陶瓷刀具、涂层刀具和硬质合金刀具进行了铁基粉末冶金零件的干切削对比试验,研究了切削速度、切削深度以及进给速度与刀具耐用度和加工表面粗糙度的关系,分析了陶瓷刀具的磨损机理。结果表明所选用陶瓷刀具的切削性能明显优于涂层刀具和硬质合金刀具;陶瓷刀具前刀面主要磨损形式为月牙洼磨损与剥落,后刀面的主要磨损原因为磨粒磨损;认为陶瓷刀具更适合用于粉末冶金零件的切削加工。     

Performance prediction of high-pressure coolant assisted turning of Ti-6Al-4V

The present study focuses on the development of predictive models of average surface roughness, chip-tool interface temperature, chip reduction coefficient, and average tool flank wear in turning of Ti-6Al-4V alloy. The cutting speed, feed rate, cutting conditions (dry and high-pressure coolant), and turning forces (cutting force and feed force) were the input variables in modeling the first three quality parameters, while in modeling tool wear, the machining time was the only variable. Notably, the machining environment influences the machining performance; yet, very few models exist wherein this variable was considered as input. Herein, soft computing-based modeling techniques such as artificial neural network (ANN) and support vector machines (SVM) were explored for roughness, temperature, and chip coefficient. The prediction capability of the formulated models was compared based on the lowest mean absolute percentage error. For surface roughness and cutting temperature, the ANN and, for chip reduction coefficient, the SVM revealed the lowest error, hence recommended. In addition, empirical models were constructed by using the experimental data of tool wear. The adequacy and good fit of tool wear models were justified by a coefficient of determination value greater than 0.99.     

Evaluation on Effectiveness of CVD and PVD Coated Tools during Dry Machining of Incoloy 825

With wide applications of nickel-based superalloys in strategic fields, it has become increasingly necessary to evaluate the performance of different advanced cutting tools for machining such alloys. With a view to recommend a suitable cutting tool, the present work investigated various machinability characteristics of Incoloy 825 using an uncoated tool, chemical vapor deposition (CVD) of a bilayer of TiCN/Al₂O₃, and physical vapor deposition (PVD) of alternate layers of TiAlN/TiN-coated tools under varying machining conditions. The influence of cutting speed (51, 84, and 124 m/min) as well as feed (0.08, 0.14, and 0.2 mm/rev) was comparatively evaluated on surface roughness, cutting temperature, cutting force, coefficient of friction, chip thickness, and tool wear using different cutting tools. Although the CVD-coated tool was not useful in decreasing surface roughness and temperature, a significant reduction in cutting force and tool wear could be achieved with the same coated tool under a high cutting speed of 124 m/min. On the other hand, the PVD-coated tool outperformed the other tools in terms of machinability characteristics. This might be attributed to the excellent antifriction and antisticking property of TiN and good toughness due to the multilayer configuration in combination with a thermally resistant TiAlN phase. Adhesion, abrasion, edge chipping, and nose wear were the prominent wear mechanisms of the uncoated tool, followed by the CVD-coated tool. However, remarkable resistance to such wear was evident with the PVD TiAlN/TiN multilayer-coated tool.     

Effects of Cutting Parameters on Tool Insert Wear in End Milling of Titanium Alloy Ti6A14V

Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6Al4 V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6Al4 V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as: feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6Al4 V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.     

Effects of cutting parameters on tool insert wear in end milling of titanium alloy Ti6Al4V

Titanium alloy is a kind of typical hard-to-cut material due to its low thermal conductivity and high strength at elevated temperatures, this contributes to the fast tool wear in the milling of titanium alloys. The influence of cutting conditions on tool wear has been focused on the turning process, and their influence on tool wear in milling process as well as the influence of tool wear on cutting force coefficients has not been investigated comprehensively. To fully understand the tool wear behavior in milling process with inserts, the influence of cutting parameters on tool wear in the milling of titanium alloys Ti6Al4V by using indexable cutters is investigated. The tool wear rate and trends under different feed per tooth, cutting speed, axial depth of cut and radial depth of cut are analyzed. The results show that the feed rate per tooth and the radial depth of cut have a large influence on tool wear in milling Ti6Al4V with coated insert. To reduce tool wear, cutting parameters for coated inserts under experimental cutting conditions are set as: feed rate per tooth less than 0.07 mm, radial depth of cut less than 1.0 mm, and cutting speed sets between 60 and 150 m/min. Investigation on the relationship between tool wear and cutting force coefficients shows that tangential edge constant increases with tool wear and cutter edge chipping can lead to a great variety of tangential cutting force coefficient. The proposed research provides the basic data for evaluating the machinability of milling Ti6Al4V alloy with coated inserts, and the recommend cutting parameters can be immediately applied in practical production.     

高硅铝合金切削性能的试验研究

由于Al-Si合金比重小、强度高、导热性好和便于回收利用等优点,广泛应用于飞机、汽车和电子科技等行业产品中。因其切削加工过程中易发生刀屑粘结、刀具磨损严重和划伤已加工表面等问题,难以获得良好的表面质量和较高的加工精度。为研究高硅铝合金的切削性能,本文以切削力和切削温度为研究对象,采用正交试验法试验,分析切削速度、进给量、铣削宽度和背吃刀量对铣削力和温度的影响。通过本研究,期望改善生产中刀具磨损严重和加工表面质量差的状况。     

Design of micro square endmills for hard milling applications

In experiments of machining hardened tool steels (such as AISI H11, H13, and D2, up to 56 HRC) by commercial ? 0.5?mm square endmills, it is observed that the tested micro endmills showed severe wear at an early stage of the process due to chipping off around cutting edge corners, resulting in unsatisfactory tool life and product appearance (burr formation). Detailed examination of current tool geometry shows that it is mainly inherited from that of macro endmills, making the cutting edge corners the weakest part on the tool. As the micromilling process is characterized by small values of machining parameters, the cutting edge corners of the micro endmill are the most loaded part of the cutting edges. New design rules are studied for improving the stiffness and strength of micro endmills used in micro hard milling applications. Analytical modelling and finite element method analysis are used to aid the design of tool geometry. By using a larger neck angle, optimizing tool core geometry, and choosing a negative rake angle, tool stiffness and cutting edge strength are improved. The new endmill designs, both two-flute and four-flute, are tested in experiments on hardened tool steels and showed considerable lower tool wear and increased tool life. Furthermore, the geometrical accuracy and appearance of the workpiece (burr formation) has been improved drastically.     

An empirical survey on the influence of machining parameters on tool wear in diamond turning of large single-crystal silicon optics

We conducted a series of screening experiments to survey the influence of machining parameters on tool wear during ductile regime diamond turning of large single-crystal silicon optics. The machining parameters under investigation were depth-of-cut, feed rate, surface cutting speed, tool radius, tool rake angle and side rake angle, and cutting fluid. Using an experimental design technique, we selected twenty-two screening experiments. For each experiment we measured tool wear by tracing the tool edge with an air bearing linear variable differential transformer before and after cutting and recording the amount of tool edge recession. Using statistical tools, we determined the significance of each cutting parameter within the parameter space investigated. We found that track length, chip size, tool rake angle and surface cutting speed significantly affect tool wear, while cutting fluid and side rake angle do not significantly affect tool wear within the ranges tested. The track length, or machining distance, is the single most influential characteristic that causes tool wear. For a fixed part area, a decrease in track length corresponds to an increase in feed rate. Less tool wear occurred on experiments with negative rake angle tools, larger chip sizes and higher surface velocities. The next step in this research is to perform more experiments in this region to develop a predictive model that can be used to select cutting parameters that minimize tool wear.     

Evaluation of performance of nanofluid using multiwalled carbon nanotubes for machining of Ti–6AL–4V

Machining of titanium alloys generate very high temperature in the cutting zone. This results in rapid tool wear and poor surface properties. Therefore, improvement in cutting performance in machining of titanium alloys is very much dependent on effectiveness of the cooling strategies applied. In the present work, performance of nanofluid using multiwalled carbon nanotubes (MWCNTs) dispersed in distilled water and sodium dodecyl sulfate (SDS) as surfactant is evaluated for turning operation on Ti–6Al–4V workpieces. Turning operations were carried out under three different conditions – dry, with conventional cutting fluid and with nanofluid. Nanofluid application was limited to 1 L/h and it was applied at the tool tip through gravity feed. Various machining responses like cutting force, surface finish and tool wear were analyzed while turning at optimum cutting parameters as 150 m/min, 0.1 mm/rev and 1 mm depth of cut. Later on, machining performance of nanofluid is confirmed at low cutting speed of 90 m/min. Nanofluid outperformed conventional cutting fluid with 34% reduction in tool wear, average 28% drop in cutting forces and 7% decrease in surface roughness at cutting speed of 150 m/min.