Thermodynamic modeling of the NiO–SiO2, MgO–NiO,CaO–NiO–SiO2, MgO–NiO–SiO2, CaO–MgO–NiO and CaO–MgO–NiO–SiO2 systems

A complete literature review, critical evaluation and thermodynamic optimization of phase equilibrium and thermodynamic properties of all available oxide phases in the NiO–SiO₂, MgO–NiO, CaO–NiO–SiO₂, MgO–NiO–SiO₂, CaO–MgO–NiO and CaO–MgO–NiO–SiO₂ systems at 1 bar pressure are presented. The molten oxide phase is described by the modified quasichemical model, and the Gibbs energies of solid olivine and pyroxene solutions were modeled using the compound energy formalism. A set of optimized model parameters of all phases is obtained which reproduces all available and reliable thermodynamic and phase equilibrium data within experimental error limits from 25 °C to above the liquidus temperatures over the entire composition range. The unexplored ternaries and quaternary phase diagrams and activity of liquid phase in the CaO–MgO–NiO–SiO₂ system have been predicted for the first time. The database of the model parameters can be used along with software for Gibbs energy minimization to calculate all thermodynamic properties and any phase diagram section of interest.     

Effect of MgO calcination temperature on the reaction products and kinetics of MgO–SiO2–H2O system

MgO-based binders have been widely studied for decades. Recently, the MgO–SiO₂–H₂O system was developed as a novel construction material, however, its reaction mechanism remains unclear. This paper investigated the reaction products and kinetics of MgO/silica fume (SF) pastes with MgO calcinated at different temperatures. The results indicate that MgO presented larger grain size after calcination at higher temperature. Mg(OH)₂ and magnesium silicate hydrate (M–S–H) gel were formed when using MgO calcined at 850, 950, and 1050°C. However, only M–S–H gel was formed when using MgO calcined at 1450°C. The reaction kinetics of MgO could be described using α = 1 − e^−k*t. The reaction rate of MgO increased with decreasing calcination temperature, increasing SF dosage, and the addition of sodium hexametaphosphate. Only M–S–H gel was formed when the reaction rate of MgO was below the demarcation line (about 0.250 × 10⁻⁶ s⁻¹), and the corresponding demarcation area was around 14 days.     

The impact of nano-quartz on the structure of glass-ceramic glazes from the SiO2–Al2O3–CaO–MgO–Na2O–K2O system

The present study reports the impact of the introduction of nano-grained quartz (SA = 325 m²/g) into the composition on the structure and properties of the ceramic glaze of the CMAS-Na₂O–K₂O system. The results were compared to the glaze which had an identical oxide composition, with a difference that quartz was introduced in the form of quartz powder with a much smaller specific surface area SA = 1.41 m²/g. Both glazes are characterized by a large part of the glassy phase, above 90% by volume. The results obtained show a higher arrangement of the continuous glassy phase structure in the glaze with the addition of nano-quartz. This glaze also shows significantly higher values for all measured mechanical properties. It seems that if, in the near future, new cheaper methods for the production of nano-quartz are developed, it will be a new interesting direction of research aimed at improving the parameters of glazes and glass-ceramic materials of CMAS type.     

Experimental investigation on high temperature wettability and structural behaviour of SAW fluxes using MgO–TiO2–SiO2 and Al2O3–MgO–SiO2 flux system

To establish the relationship between wettability and structure with the change in SAW flux composition, the contact angle measurement study was performed at 1700 K. For MgO–TiO₂–SiO₂ and Al₂O₃–MgO–SiO₂ flux system the wetting behaviour was studied by evaluating the contact angle as well as surface tension properties. Sessile drop method was used to determine the wetting properties of SAW fluxes. Twenty-one SAW fluxes were designed & developed by applying mixture design approach of design of experiments. Chemical, phase and structural properties of SAW fluxes were measured using modern techniques such as X-ray fluorescence (XRF), X-ray diffraction (XRD) & Fourier Transform Infra-red spectroscopy (FTIR). As per the calculated contact angle value, different surface tension values for MgO–TiO₂–SiO₂ and Al₂O₃–MgO–SiO₂ flux system was calculated using Young's & Boni's equations. Using Dupre's equation the adhesion energy for twenty-one basic fluxes was also calculated. Measured contact angle value increased with increase in the TiO₂/MgO & TiO₂/Al₂O₃ flux ratio. Lower contact angle gives higher wettability between the flux and the heating substrate. With increase of TiO₂/SiO₂ ratio up to 1.5 to 2.0 the calculated surface tension value is decreasing while after that it is increased with increase in TiO₂/SiO₂ ratio.     

Structural and thermal characterization of CaO–MgO–SiO2–P2O5–CaF2 glasses

The influence of varying the CaO/MgO ratio on the structure and thermal properties of CaO–MgO–SiO₂–P₂O₅–CaF₂ glasses was studied in a series of eight glass compositions in the glass forming region of diopside (CaMgSi₂O₆)–fluorapatite [Ca₅(PO₄)₃F]–wollastonite (CaSiO₃) ternary system. The melt-quenched glasses were characterized for their structure by infrared spectroscopy (FTIR) and magic angle spinning (MAS)-nuclear magnetic resonance (NMR) spectroscopy. Silicon is predominantly present as Q² (Si) species, while phosphorus tends to coordinate in orthophosphate environment. The sintering and crystallization parameters of the glasses were obtained from differential thermal analysis (DTA) while crystalline phase fractions in the sintered glass–ceramics were analyzed by X-ray diffraction adjoined with Rietveld refinement. Diopside, fluorapatite, wollastonite and pseudowollastonite crystallized as the main crystalline phases in all the glass–ceramics with their content varying with respect to variation in CaO/MgO ratio in glasses. The implications of structure and sintering behaviour of glasses on their bioactivity were discussed.     

The chemical durability of SrO–MgO–ZrO2–SiO2 glasses in strongly alkaline environments

A large region of glass formation was found in the system SrO–MgO–ZrO₂–SiO₂ and some properties have already been reported. Detailed studies have shown that glasses with only 40 wt% silica unusually durable in 1 M NaOH and also in model cement extract solutions. Glasses with higher silica contents are more easily attacked; zirconia and magnesia are the constituents giving the best durability. These results suggest that these glasses could be of interest for reinforcement of cement and concrete.     

Corrosion modeling of magnesia aggregates in contact with CaO–MgO–SiO2 slags

Ladle refining is an efficient process for improvement of quality of steel on secondary metallurgy under harsh conditions. Magnesia refractories with high purity are important raw materials for ladle lining in high-quality steel production. However, the penetration by CaO–MgO–SiO₂ slags damages magnesia refractories, which considerably limits their service life. Abundant grain boundaries in magnesia create channels for slag penetration and lead to the destruction of the structure. The effect of the microstructure on the slag corrosion behavior of magnesia aggregates requires further systematic investigation. In this study, a corrosion model was established to describe the slag penetration process of magnesia aggregates. The effects of the grain-boundary size and slag CaO/SiO₂ mass ratio (C/S ratio) on slag penetration were investigated, and the possibility of the microstructure optimization of magnesia aggregates was discussed. The results indicated that magnesia aggregates exhibited excellent slag resistance for slag with a C/S ratio above 1.5 or even 2.0. When the slag C/S ratio was lower than 1.5, the dissolution rate of magnesia decreased more rapidly with the increase in the slag C/S ratio. In addition, the much smaller grain-boundary size increased the slag penetration resistance by promoting the formation of a dense isolation layer and inhibiting further penetration processes. The calculation results agreed well with the experimental results, suggesting that the corrosion model is promising for predicting slag corrosion.     

Characterization and sintering of gels in the system MgO–Al2O3–SiO2

Cordierite aerogels, made by supercritical drying, and xerogels, formed by ambient pressure drying, have been prepared by combining two different recipes. The chemical composition of the gels varied from stoichiometric cordierite 2MgO·Al₂O₃·5SiO₂ to 0·5MgO·1·4Al₂O₃·5SiO₂ due to different procedures for washing of the gels. The crystallization of nearly stoichiometric cordierite gels was shown to be relatively complex involving the formation of several metastable phases such as μ-cordierite (Mg₂Al₄Si₅O₁₈), spinel (Al₆Si₂O₁₃) and sapphirine (Mg₄Al₈Si₂O₂₀) before the equilibrium phase composition was obtained at around 1350°C. On the other hand, during crystallization of gels with stoichiometry close to 0·5MgO·1·4Al₂O₃·5SiO₂ the equilibrium phases mullite, cristobalite and α-cordierite were the major phases formed during heat treatment. A lower densification rate was observed for aerogels compared to xerogels due to a larger pore size. A lower crystallization temperature in aerogels probably due to heterogeneous nucleation reduced the densification. For gels with a composition near 0·5MgO·1·4Al₂O₃·5SiO₂ nucleation and densification occur simultaneously and large differences in the densification behavior was observed. ©     

The role of MgO on the structural properties of CaO–Na2O(MgO)–P2O5–CaF2–SiO2 derived glass ceramics

The effect of increasing MgO/Na₂O replacements (on mole basis) on the crystallization characteristics of glasses based on the CaO–Na₂O(MgO)–P₂O₅–CaF₂–SiO₂ system were studied by using DTA, XRD, and SEM. The crystallization characteristics of the glasses, the type of crystalline phases formed and the resulting microstructure were investigated. The main crystalline phases formed after controlled heat-treatment of the base glass were diopside, wollastonite solid solution, fluoroapatite and sodium calcium silicate phases. The increase of MgO at the expense of Na₂O led to decrease the amount of sodium calcium silicate phase. The Vicker's microhardness values (5837–3362 MPa) of the resulting glass–ceramics were markedly improved by increasing the MgO-content in the glasses. The obtained data were correlated to the nature and concentration of the crystalline phases formed and the resulting microstructure.     

Raman and X-ray photoelectron spectroscopy study on the influence of La2O3 on the melt structure of SiO2–CaO–Al2O3–MgO

In order to gain more insights into the influence of rare earth elements on the melt structure of SiO₂–CaO–Al₂O₃–MgO glass ceramics, Raman and X-ray photoelectron spectroscopy techniques were used to study the influence of La₂O₃ on the Si–O/Al–O tetrahedron structure within SiO₂–CaO–Al₂O₃–MgO–quenched glass samples in this study. Results showed that some Raman peak shapes at low frequencies (200–840 cm^?1) changed significantly after the addition of La₂O₃, compared to the high frequency (840–1200 cm^?1) region that corresponds to the [SiO₄] structure, suggesting that the depolymerization of the low-frequency T–O–T (T=Si or Al) structure was more prevalent with La³⁺ addition. Besides, the depolymerization extent of the Si–O/Al–O tetrahedral network varied when the melt composition altered. Most notably, depolymerization is the most significant at a low CaO/SiO₂ ratio (0.25) and a high Al₂O₃ content (8%). Meanwhile, La³⁺ can promote the transformation of Si–O–Si and Al–O–Al bonds to the Si–O–Al ones, thereby forming a complex ionic cluster network interwoven with Si–O and Al–O tetrahedrons.     

Effect of P2O5 on evolution of microstructure of MgO–Al2O3–SiO2 glass ceramics

Abstract

MgO–Al₂O₃–SiO₂ (MAS) cordierite based glass ceramics were prepared by volume crystallisation. X-ray diffraction, Scanning electron microscopy and Energy diffraction scanning were used to investigate crystallisation behaviour and the influence of P₂O₅ on microstructure MAS based glass ceramics. The results showed that P⁵⁺ could promote the phase separation of MAS glass and that the glass was divided into two areas, such as Mg₄Al₂Ti₉O₂₅ and the containing P⁵⁺ area at <900°C. Mg₄Al₂Ti₉O₂₅ and Mg₃(PO₄)₂ in the area were both advantageous to the precipitation of μ cordierite, which further transformed to α cordierite due to P⁵⁺ in the residual glassy phase. However, P⁵⁺ inhibited the presence of cordierite when the heat treatment temperature was >900°C.     

Dissolution behavior of silica in molten CaO–SiO2–Fe2O3–MgO–MnO slag

The modification of basic oxygen furnace (BOF) slag by adding silica can improve the properties of BOF slag for applications in the cement industry. The rapid dissolution of silica is essential to hot slag modification. In this work, the dissolution behavior of silica in the molten CaO–SiO₂–Fe₂O₃–MgO–MnO system as synthetic BOF slag was investigated by using the traditional rotating cylinder technique. Effects of rotation speed, temperature, immersion time, and slag basicity on the silica dissolution were studied. Scanning electron microscopy equipped with energy dispersive spectrometer (SEM-EDS) and FactSage simulations were employed to reveal the dissolution mechanism. It was found that the dissolution of the silica rod was affected by both the thermodynamic driving force and the slag viscosity. The silica dissolution rate in molten CaO–SiO₂–Fe₂O₃–MgO–MnO slag increased with increasing the rotation speed and temperature, but first increased and then decreased when decreasing the slag basicity from 2.5 to 1.5. A linear correlation between the logarithm of the dissolution rate and the logarithm of cylinder periphery velocity with a slope of 0.44 was observed, indicating the mass transfer within the boundary layer as the dissolution rate determining step. A direct dissolution way was found during the dissolution of silica in molten CaO–SiO₂–Fe₂O₃–MgO–MnO slag.     

Preparation of α-cordierite through mechanochemical activation of MgO–Al2O3–SiO2 ternary system

Samples of the ternary system MgO–Al₂O₃–SiO₂ with stoichiometric composition in relation to α-cordierite (Mg₂A_l4Si₅O₁₈), consisting of 22.2 mol% MgO, 22.2 mol% Al₂O₃, and 55.6 mol% SiO₂, were activated in a low energy mill with a constant speed of 100 rpm, in an aqueous medium. The precursors used were corundum (Al₂O₃), silica gel HF254 type 60 (SiO₂), and periclase (MgO). The objective of the present study was to evaluate the effect of mechanochemical activation on the solid-state synthesis of α-cordierite, using a low energy ball mill. Another objective was to shed light on the effect of mechanochemical activation on the steps of α-cordierite formation. For this end several grinding conditions were evaluated, varying the time and mass ratio of precursors/grinding elements, as well as calcination at different temperatures between 950 °C and 1350 °C for 2 h. The samples were analyzed for the determination of the formed phases by Infrared (IR) and X-ray Diffraction (XRD). The phases identified in uncalcined samples were brucite (Mg(OH)₂), forsterite (Mg₂SiO₄), enstatite (MgSiO₃), spinel (MgAl₂O₃), amorphous silica (SiO₂), corundum (α-Al₂O₃), and zirconia (monoclinic and tetragonal ZrO₂). The lowest temperature corresponding to the formation of α-cordierite (α-Mg₂Al₄Si₅O₁₈) was 1150 °C and a considerable amount of this phase (16.2%) was observed at this temperature, for the sample with the higher mechanochemical activation. In a solid-state reaction, α-cordierite is normally obtained at around 1400 °C, therefore, the formation of this phase at 1150 °C confirms that the mechanochemical activation method, using a low-cost ball mill, is efficient in reducing the solid-state reaction temperature.     

Phase equilibria studies in the CaO–SiO2–Al2O3–MgO system with CaO/SiO2 ratio of 0.9

Phase equilibria and liquidus temperatures in the CaO–SiO₂–Al₂O₃–MgO system at a CaO/SiO₂ weight ratio of 0.9 in the liquid phase have been experimentally determined employing high-temperature equilibration and quenching technique followed by electron probe X-ray microanalysis. Isotherms at 1573, 1623, 1673, and 1773 K were determined and the primary phase fields of wollastonite, melilite, olivine, periclase, spinel, and corundum have been located. Compositions of the olivine and melilite solid solutions were analyzed and discussed. Comparisons between the newly constructed diagram, existing data, and FactSage predicted phase diagrams were performed and differences were discussed. The present study will be useful for guidance of industrial practices and further development of thermodynamic modeling.     

Influence of nucleating agents on crystallization and electrical properties of SiO2–MgO–MgF2–K2O mica glass-ceramics

The effects of adding ZrO₂ and TiO₂ at the expense of MgF₂ on the crystallization, microstructure, mechanical properties, thermal properties and electrical properties of mica glass-ceramics based on the SiO₂–MgO–MgF₂–K₂O system were investigated by the differential scanning calorimetry (DSC), X-ray powder diffraction (XRD), scanning electron microscopy (SEM), microhardness tester and resistivity tester. The electrical properties were discussed emphatically. The results showed that the additions of ZrO₂ and/or TiO₂ at the expense of MgF₂ effectively increase the viscosity, the glass transition temperatures (T_g) and the crystallization temperatures (T_p) of the glasses. The crystallization activation energy (E_c) of the amorphous glasses varied with the nucleating agents was discussed in depth. It was discovered that the nucleating agents had no effect on the crystal phase type but had a certain effect on the crystallinity and microstructure. Tetrasilicic fluoromica and enstatite were precipitated at different crystallization temperatures. Due to the non-stoichiometric ratio of tetrasilicic fluoromica crystal, the prepared glass-ceramics had high dielectric constant (24.4–34.3) and volume resistivity (>2 × 10¹¹ Ω cm) at 25 ^°C, and the dielectric loss was almost zero.     

Thermal Stability and Crystallization Kinetics of MgO–Al2O3–B2O3–SiO2 Glasses

To support commercialization of the MgO–Al₂O₃–B₂O–SiO₂-based low-dielectric glass fibers, crystallization characteristics of the relevant glasses was investigated under various heat-treatment conditions. The study focused on the effects of iron on the related thermal properties and crystallization kinetics. Both air-cooled and nucleation-treated samples were characterized by using the differential thermal analysis/differential scanning calorimeter method between room temperature and 1200°C. A collected set of properties covers glass transition temperature (T_g), maximum crystallization temperature (T_p), specific heat (ΔC_p), enthalpy of crystallization (ΔH_cryst), and thermal stability (ΔT=T_p—T_g). Using the Kinssiger method, the activation energy of crystallization was determined. Crystalline phases in the samples having various thermal histories were determined using powder X-ray diffraction (XRD) and/or in situ high-temperature XRD method. Selective scanning electron microscope/energy-dispersive spectroscopy analysis provided evidence that crystal density in the glass is affected by the iron concentration. Glass network structures, for air-cooled and heat-treated samples, were examined using a midinfrared spectroscopic method. Combining all of the results from our study, iron in glass is believed to function as a nucleation agent enhancing crystal population density in the melt without altering a primary phase field. By comparing the XRD data of the glasses in two forms (bulk versus powder), the following conclusions can be reached. The low-dielectric glass melt in commercial operation should be resistant to crystallization above 1100°C. Microscopic amorphous phase separation, possibly a borate-enriched phase separating from the silicate-enriched continuous phase can occur only if the melt is held at temperatures below 1100°C, that is, below the glass immiscibility temperature. The study concludes that neither crystallization nor amorphous phase separation will be expected for drawing fibers between 1200°C and 1300°C in a commercial operation.     

Microwave dielectric materials based on the MgO–SiO2–TiO2 system

Ceramics in the system MgO–SiO₂–TiO₂ were prepared by standard mixed oxide route. By adding ZnO–B₂O₃ to the starting mixtures, the firing temperature of the ceramics could be reduced to 1160 °C. Small additions of MnCO₃ and CaTiO₃ improve microwave dielectric properties leading to an increase in insulation resistance and a decrease in temperature coefficient of capacitance. By adding Co₂O₃ grain growth can be inhibited and the dielectric Qf value greatly increased. The resultant ceramic material exhibited low dielectric constant and low dielectric loss: relative permittivity (ε_r): 20±2; temperature coefficient of capacitance (τ_c): 0±30 ppm/°C; Qf: 100,000 (at 10 GHz); insulation resistance: 10¹³ Ω cm:     

Synthesis of K2O–MgO–SiO2 compounds as slow-release fertilisers from acid-leached biotite residues

For the utilisation of mineral residues and improving the nutrient use efficiency in fertilisers, the K₂O–MgO–SiO₂ compounds prepared as slow-release K fertilisers by using the acid-leached biotite residues, K₂CO₃, and Mg(OH)₂ as the starting materials were systematically studied and evaluated in this work. Sintering experiments were performed at 700–1000 °C and solubility experiments were conducted by dissolving the sintered samples in 0.50 M HCl solution, 0.10 M citric acid solution, and water. The results showed that K₂MgSiO₄ (KMS), KMS-K_1.14Mg_0.57Si_1.43O₄(K₂M₂S₅)–K₂MgSi₃O₈(KMS₃) mixtures, and K₂MgSi₅O₁₂ (KMS₅) were synthesised at 800 °C, 850–900 °C, and 950 °C, respectively. These compounds are citrate-soluble, and the solubilities followed the order KMS > K₂M₂S₅ ≫ KMS₃ > KMS₅. The release properties of the K₂O accumulated in water for all the K₂O–MgO–SiO₂ compounds fit the release kinetics Elovich equations, which suggest that KMS and KMS-K₂M₂S₅-KMS₃ can be used as slow-release K fertilisers and that KMS₅ with a much slower release of K₂O may be more suitable as a soil conditioner. Evaluation of the raw materials, synthesis approach, product properties, and environmental benefits shows that K₂O–MgO–SiO₂ slow-release fertilisers are eco-friendly and offer plenty of advantages with regard to soil fertility, environmental protection, resource utilisation, and energy consumption.     

The MgO–TiO2–SiO2 system: Experiments and thermodynamic assessment

Phase relations in the MgO–TiO₂–SiO₂ system have been investigated in air over a wide temperature range using the equilibration method. X-ray powder diffraction, scanning electron microscopy combined with wave length X-ray spectroscopy (SEM/EPMA), and differential thermal analysis (DTA) have been used for sample characterization. Based on the obtained experimental results, isothermal sections of the system at 1523, 1673, and 1773 K have been established. The solid-state invariant reaction MgTi₂O₅ + T-SiO₂⇋P-MgSiO₃ + TiO₂ has been detected at 1625 ± 8 K by step-wise heat treatment. A partial liquidus projection has been suggested, and the temperatures and compositions of three eutectic invariant reactions have been experimentally measured by DTA and ex-situ analysis of the sample microstructures after melting using SEM/EPMA. Considering the newly obtained experimental data, thermodynamic parameters describing the system have been thermodynamically evaluated within the CALPHAD approach.