Near infrared light-induced photocurrent in NaYF4:Yb3+, Er3+/WO2.72 composite film

Spectral conversion technology based on NaYF₄:Yb³⁺, Er³⁺ upconversion nanoparticles was extensively used to improve photovoltaic conversion efficiency of solar cells. However, the response mismatch between absorption of semiconductors and upconversion luminescence (UCL) limits the application of spectral conversion technology. Nonstoichiometric WO_2.72 nanoparticles display the broad absorption from visible to near-infrared region due to the presence of oxygen vacancy, which is overlapped with the UCL of NaYF₄:Yb³⁺, Er³⁺ nanoparticles. Thus, the combination between NaYF₄:Yb³⁺, Er³⁺ nanoparticles, and nonstoichiometric WO_2.72 provides a possibility for designing a novel UCL spectral converted solar cells. In this work, composite film consisted of NaYF₄:Yb³⁺, Er³⁺ nanoparticles, and WO_2.72 nanofibers was prepared. The UCL of NaYF₄:Yb³⁺, Er³⁺/WO_2.72 film was decreased in contrast to pure NaYF₄:Yb³⁺, Er³⁺ nanoparticles due to energy transfer from NaYF₄:Yb³⁺, Er³⁺ nanoparticles to WO_2.72 nanofibers. The NaYF₄:Yb³⁺, E³⁺/WO_2.72film exhibits the photocurrent generation upon the 980 nm excitation. This novel UCL spectral converted solar cells based on the broad absorption of defects in the WO_2.72 host will provide a novel view for photovoltaic devices.     

Abnormal upconversion luminescence induced by defects and Er3+–Yb3+ distance change in Cs3GdGe3O9:Er3+/Yb3+ phosphors

A series of Er³⁺/Yb³⁺ co-doped Cs₃GdGe₃O₉ (CGG) phosphors were prepared by solid-phase sintering method, and the microstructure and upconversion luminescence (UCL) properties were tested by variable-temperature X-ray diffractometry and variable-temperature spectrometer. Abnormal UCL phenomena were found, which include UCL intensity continuously increasing under 980 nm laser continuous irradiation and UCL thermal enhancement. After 10 min of continuous irradiation by 980 nm laser at 513 K, the UCL intensity increased 2.91 times compared with the initial UCL intensity. The phenomenon is due to the electron releasing of host defects. The green UCL intensity of CGG:0.1Er³⁺/0.2Yb³⁺ decreases at 303–423 K and increases at 423–723 K, which reaches 13.23 times compared with that at 423 K. The phenomenon is due to Er³⁺–Yb³⁺ distance change by temperature and phonon-assisted transitions. In addition, the absolute temperature sensitivities of samples are calculated by luminescence intensity ratio technology, the maximum absolute sensitivity of CGG:0.1Er³⁺/0.4Yb³⁺ is 0.00691 K⁻¹ at 546 K, and the maximum relative sensitivity of CGG:0.1Er³⁺/0.1Yb³⁺ is 0.01224 K⁻¹ at 303 K. These results indicate that CGG:Er³⁺/Yb³⁺ phosphors can be used as a high-temperature optical thermometer.     

Upconversion emission,cathodoluminescence and temperature sensing behaviors of Yb3+ ions sensitized NaY(WO4)2:Er3+ phosphors

A series of Yb³⁺ ions sensitized NaY(WO₄)₂:Er³⁺ phosphors were synthesized through a solid-sate reaction method. The X-ray diffraction (XRD), upconversion (UC) emission and cathodoluminescence (CL) measurments were applied to characterize the as-prepared samples. Under the excitation of 980 nm light, bright green UC emissions corresponding to (²H_11/2,⁴S_3/2)→⁴I_15/2 transitions of Er³⁺ ions were observed and the UC emission intensities showed an upward trend with increasing the Yb³⁺ ion concentration, achieving its optimum value at 25 mol%. Furthermore, the temperature sensing behavior based on the thermally coupled levels (²H_11/2,⁴S_3/2) of Er³⁺ ions was analyzed by a fluorescence intensity ratio technique. It was found that the obtained samples can be operated in a wide temperature range of 133–773 K with a maximum sensitivity of approximately 0.0112 K⁻¹ at 515 K. Ultimately, strong CL properties were observed in NaY(WO₄)₂:0.01Er³⁺/0.25Yb³⁺ phosphors and the CL emission intensity increased gradually with the increment of accelerating voltage and filament current.     

Preparation,luminescence properties,and application of temperature sensing and anti-counterfeiting of La2MgTiO6:Yb3+/Ln3+/Mn4+

The doping of transition metal ions in the up-conversion (UC) luminescent material doped with Yb³⁺/Ln³⁺ is a facile way to increase their UC luminescence intensities and alter their colors. In this study, La₂MgTiO₆:Yb³⁺/Mn⁴⁺/Ln³⁺ (Ln³⁺ = Er³⁺, Ho³⁺, and Tm³⁺) phosphors showing excellent luminescence properties were prepared by a solid-state method. The sensitivity of the La₂MgTiO₆:Yb³⁺/Ln³⁺/Mn⁴⁺ phosphor was double that without Mn⁴⁺, because Mn⁴⁺ affects the UC emissions of Ln³⁺ via energy transfer between these ions. Moreover, Mn⁴⁺ also acts as a down-conversion activator, which can combine with UC ions to achieve multi-mode luminescence at different wavelengths. Under 980 nm excitation, these samples emit green light (from Er³⁺ and Ho³⁺) and blue light (from Tm³⁺). In contrast, under 365 nm excitation, they emit red light (from Mn⁴⁺). Further testing revealed that the La₂MgTiO₆:Yb³⁺/Mn⁴⁺/Ln³⁺ phosphors have potential applications in temperature sensing and anti-counterfeiting.     

Microwave Sol–Gel Synthesis of CaGd2(MoO4)4:Er3+/Yb3+ Phosphors and Their Upconversion Photoluminescence Properties

CaGd₂(MoO₄)₄:Er³⁺/Yb³⁺ phosphors with the doping concentrations of Er³⁺ and Yb³⁺ (x = Er³⁺ + Yb³⁺, Er³⁺ = 0.05, 0.1, 0.2, and Yb³⁺ = 0.2, 0.45) have been successfully synthesized by the microwave sol–gel method, and the crystal structure refinement and upconversion photoluminescence properties have been investigated. The synthesized particles, being formed after heat‐treatment at 900°C for 16 h, showed a well‐crystallized morphology. Under the excitation at 980 nm, CaGd₂(MoO₄)₄:Er³⁺/Yb³⁺ particles exhibited strong 525 and 550‐nm emission bands in the green region and a weak 655‐nm emission band in the red region. The Raman spectrum of undoped CaGd₂(MoO₄)₄ revealed about 15 narrow lines. The strongest band observed at 903 cm^?1 was assigned to the ν₁ symmetric stretching vibration of MoO₄ tetrahedrons. The spectra of the samples doped with Er and Yb obtained under 514.5 nm excitation were dominated by Er³⁺ luminescence preventing the recording Raman spectra of these samples. Concentration quenching of the erbium luminescence at ²H_11/2→⁴I_15/2 and ⁴S_3/2→⁴I_15/2 transitions in the CaGd₂(MoO₄)₄:Er³⁺/Yb³⁺ crystal structure was established to be approximately at the 10 at.% doping level.     

A Novel Multifunctional Upconversion Phosphor: Yb3+/Er3+ Codoped La2S3

Yb³⁺/Er³⁺ codoped La₂S₃ upconversion (UC) phosphors have been synthesized using high‐temperature solid‐state method. Under 971‐nm excitation, the maximum luminescence power can reach 0.64 mW at the excitation power density of 16 W/cm² and an absolute power yield of 0.36% was determined by an absolute method at the excitation power density of 3 W/cm², and the quantum yield of La₂S₃:Yb³⁺, Er³⁺ (green ~0.18%, red ~0.03%, integration ~0.21) was comparable to that of NaYF₄:Yb³⁺, Er³⁺ nanocrystals (integration ~0.005–0.30). Frequency upconverted emissions from two thermally coupled excited states of Er³⁺ were recorded in the temperature range 100–900 K. The maximum sensitivity of temperature sensing is 0.0075 K^?1. As the excitation power density increases, the temperature of host materials rapidly rises and the top temperature can reach to 600 K. Given the intense UC emission, high sensitivity, as well as good photothermal stability, La₂S₃:Yb³⁺/Er³⁺ phosphor can become a promising composite material for photothermal ablation of cancer cells possessing the functions of temperature sensing and in vivo imaging.     

Thermal enhancement of up-conversion luminescence in Lu2W2.5Mo0.5O12: Er3+, Yb3+ phosphors

Lu₂W_2.5Mo_0.5O₁₂: Er³⁺/Yb³⁺ phosphors were synthesized through high temperature solid state method. Under 980 nm laser excitation, the Lu₂W_2.5Mo_0.5O₁₂: Er³⁺/Yb³⁺ compounds show thermal enhancement of up-conversion luminescence (UCL), which is attributed to the lattice contraction and distortion from negative thermal expansion (NTE) of Lu₂W_2.5Mo_0.5O₁₂ host enhancing the energy transfer of Yb³⁺ to Er³⁺, eliminating the energy transfer of Er³⁺ to Er³⁺ through Er³⁺ single-doped Lu₂W_2.5Mo_0.5O₁₂ phosphors without thermal enhancement of UCL. The green luminescence intensities at 693 K of the Lu_1.98-xW_2.5Mo_0.5O₁₂: 0.02Er³⁺, xYb³⁺ (x = 0.2, 0.3, 0.4) samples are 4.6, 4.3 and 7.0 times as that of 302 K, respectively. And through fluorescence intensity ratio (FIR) technique, the corresponding maximum absolute sensitivities are 0.00741, 0.00744 and 0.00723, respectively. The green monochromaticity of UCL spectra in Er³⁺/Yb³⁺ co-doped samples increase with the increasing of temperature, and the possible UCL mechanism with temperature was discussed. The results indicate that the Lu₂W_2.5Mo_0.5O₁₂: Er³⁺/Yb³⁺ phosphors can be applied at a high temperature as optical thermometer with a good green monochromaticity.     

BiLaWO6: Er3+/Tm3+/Yb3+ phosphor: Study of multiple fluorescence intensity ratiometric thermometry at cryogenic temperatures

Highly thermally stable Er³⁺/Tm³⁺/Yb³⁺ tri-doped bismuth lanthanum tungstate phosphors were prepared by high temperature solid-state reaction method. The structural and morphological properties of the prepared phosphors were analysed by X-ray diffraction (XRD), Raman spectroscopy and Scanning electron microscopy (SEM) coupled with energy dispersion spectrum (EDS). Visible upconversion (UC) luminescence was measured by exciting the phosphors with 980 nm laser radiation. The dependence of the UC intensity of each emission band of Er³⁺ and Tm³⁺ ions as a function of temperature in the range from 30 to 300 K was monitored. Fluorescence intensity ratios (FIR) of thermally coupled levels (TCL) and non-thermally coupled levels (NTCL) were analysed and verified with appropriate theoretical validation. The absolute (S_A) and relative sensitivities (S_R) were estimated and compared with the reported systems. In the present case of BiLaWO₆: Er³⁺/Tm³⁺/Yb³⁺, S_R (0.43 % K^?1) related to TCL of Er³⁺ UC is found to have maximum sensitivity compared to any of the NTCL combinations at 300 K. From this study we inferred that the S_R values estimated from NTCL are smaller than that of TCL involved in BLW: Er³⁺/Tm³⁺/Yb³⁺ phosphor. The temperature dependent CIE color coordinates were also evaluated in the cryogenic temperature region.     

Tunable multicolor upconversion luminescence of Yb3+ sensitized Na3La(VO4)2 crystals

Multicolor upconversion luminescence materials show significantly applications in materials science. In this paper, the novel Yb³⁺-sensitized Na₃La(VO₄)₂ upconversion luminescence crystals are synthesized by the solid-state reaction method. Three primary colors upconversion luminescence are successfully achieved in Na₃La(VO₄)₂:Yb³⁺,Tm³⁺, Na₃La(VO₄)₂:Yb³⁺,Er³⁺, and Na₃La(VO₄)₂:Yb³⁺,Ho³⁺ crystals excited by the single 980 nm LD. Multicolor upconversion luminescence can be obtained by simply adjusting the combination ratios of these three samples. Luminescence mechanisms of the Yb³⁺-sensitized system are discussed in detail. In the Na₃La(VO₄)₂ host material, the Yb³⁺/Ho³⁺ codoped system exhibits unusual red upconversion luminescence based on the short decay time of Ho³⁺ ion ⁵I₆ level, which provides the possibility of three primary color luminescence under 980 nm excitation.     

Broad-scope dual-mode modulation thermometry based on up-conversion phosphor GaNbO4: Yb3+/Er3+

Fluorescence temperature measurement technology has set off another upsurge in non-contact temperature measurement, but still suffers from the large error for single-mode thermometry. Herein, in a broad temperature range of 93–633 K, a dual-mode modulation thermometry based on up-conversion phosphor of GaNbO₄:Yb³⁺/Er³⁺ is realized with the maximum relative sensitivity (S_r) of 11.7% K⁻¹ (93 K) and 13.1% K⁻¹ (123 K), respectively. GaNbO₄:Yb³⁺/Er³⁺ phosphors were synthesized by high temperature solid-state method. The structure, surface morphology and the optical properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and photoluminescence (PL). The fluorescence intensity ratio (FIR) readout method based on Er³⁺ thermal-coupled energy level (TCL) and non-thermal-coupled energy level (NTCL) was used to achieve the dual-mode temperature measurement with high temperature resolution and good repeatability in GaNbO₄:5 mol% Yb³⁺ and 5 mol% Er³⁺ phosphors. All the results show that GaNbO₄:Yb³⁺/Er³⁺ phosphors have great application potential in high sensitivity broadband thermometry.     

Color-tunable up-conversion emission from Yb3+/Er3+/Tm3+/Ho3+ codoped KY(MoO4)2 microcrystals based on energy transfer

Tunable up-conversion luminescent material KY(MoO₄)₂: Yb³⁺, Ln³⁺ (Ln=Er, Tm, Ho) has been synthesized by a typical hydrothermal process. Under 980 nm laser diode (LD) excitation, the emission intensity and the corresponding luminescence colors of KY(MoO₄)₂: Yb³⁺, Ln³⁺ (Ln=Er, Tm, Ho) have been investigated in detail. The energy transfer from the Yb³⁺ sensitizer to Ho³⁺, Er³⁺ and Tm³⁺ activators plays an important role in the development of color-tunable single- phased phosphors. The emission intensity keep balance through control of the Ho³⁺ co-doping concentrations, white light was experimentally shown at KY(MoO₄)₂: 20 mol% Yb³⁺, 0.8 mol% Er³⁺, 0.5 mol% Tm³⁺, 1.0 mol% Ho³⁺ phosphor with further calcination at 800 °C for 4 h under 980 nm laser excitation. The color tunability, high quality of white light and high intensity of the emitted signal make these up-conversion (UC) phosphors excellent candidates for applications in solid-state lighting.     

Visible green upconversion luminescence of Er3+/Yb3+/Li+ co-doped CaWO4 particles

The upconversion (UC) luminescence of Li⁺/Er³⁺/Yb³⁺ co-doped CaWO₄ phosphors is investigated in detail. Single crystallized CaWO₄:Li⁺/Er³⁺/Yb³⁺ phosphor can be obtained, co-doped up to 25.0/5.0/20.0 mol% (Li⁺/Er³⁺/Yb³⁺) by solid-state reaction. Under 980 nm excitation, CaWO₄:Li⁺/Er³⁺/Yb³⁺ phosphor exhibited strong green UC emissions visible to the naked eye at 530 and 550 nm induced by the intra-4f transitions of Er³⁺ (²H_11/2,⁴S_3/2→⁴I_15/2). The optimum doping concentrations of Yb³⁺/Li⁺ for the highest UC luminescence were verified to be 10/15 mol%, and a possible UC mechanism that depends on the pumping power is discussed in detail.     

Upconversion thermal enhancement of 2H11/2→4I15/2 of Er3+ and blue emission of impurity Tm3+ in Sr3(PO4)2:Er3+/Yb3+

A series of Sr_2.99-x(PO₄)₂:.01Er³⁺/xYb³⁺ (x = .02, .04, .06, .08, .10) phosphors in the presence of impurity Tm³⁺ were synthesized by high temperature solid-state method, and X-ray diffraction results show that these samples are pure R-3 m(166) space group phase. The upconversion luminescence (UCL) of Er³⁺ and impurity Tm³⁺ under 980-nm laser excitation were investigated, and the results show that the intense blue UCL of impurity Tm³⁺ and thermal enhancement of ²H_11/2→⁴I_15/2 of Er³⁺ simultaneously exist. When Er³⁺ doping concentration is kept at .01, both the blue UCL intensity of impurity Tm³⁺ and green and red UCL intensity of Er³⁺ reach the maximum at Yb³⁺ doping concentration of .08. The thermal enhancement effect of ²H_11/2→⁴I_15/2 of Er³⁺ was observed as high as 3.27 times from 303 to 723 K, which is because of lattice distortion and phonon-assisted transition. In addition, the optical temperature performance of Sr_2.91(PO₄)₂:.01Er³⁺/.08Yb³⁺ sample was studied, and the maximum absolute temperature sensitivity was calculated as .00623 K⁻¹ at 538 K. This study suggests that Sr₃(PO₄)₂:Er³⁺/Yb³⁺ phosphors in the presence of impurity Tm³⁺ have a promising application prospect as optical temperature sensor at high temperature.     

Yb3+/Er3+ co-doped Gd2Te4O11 nanosheets with intrinsic polarity: One-step hydrothermal synthesis and upconverted optical temperature measuring ability

The digadolinium tellurite phosphors of Gd₂Te₄O₁₁(GTO):Yb³⁺/Er³⁺ have been successfully synthesized as upconversion luminescence (UCL) materials via one-step hydrothermal method. The crystal structure, morphology, and upconversion luminescence property were systematically characterize by XRD, SEM, and spectroscopy techniques. The Rietveld refinements of crystal structure were carried out on the XRD patterns and the feature of crystal structure was analyzed. Under the 980 nm NIR excitation, these materials showed very bright upconverted emissions. The concentrations of Yb³⁺ and Er³⁺ were optimized and the strongest upconverted emissions were achieved in the GTO:15%Yb³⁺/1%Er³⁺. The possible energy transfer mechanism of UCL was proposed based upon the analysis of power-dependent UCL and fluorescence kinetics. Furthermore, the fluorescence intensity ratio (FIR) derive from the two thermally coupled energy levels (²H_11/2 and ⁴S_3/2) of Er³⁺ was employed as indicator for temperature measurement. The maximum absolute sensitivity can be achieved to be 7.34 × 10^?3 K^?1 at 501 K. This material exhibited good reliability and repeatability in optical temperature measurement, which could be a novel promising candidate for noncontact temperature sensors.     

Upconversion luminescence properties of NaBi(MoO4)2:Ln3+, Yb3+ (Ln = Er,Ho) nanomaterials synthesized at room temperature

Studies on lanthanide ions doped upconversion nanomaterials are increasing exponentially due to their widespread applications in various fields such as diagnosis, therapy, bio-imaging, anti-counterfeiting, photocatalysis, solar cells and sensors, etc. Here, we are reporting upconversion luminescence properties of NaBi(MoO₄)₂:Ln³⁺, Yb³⁺ (Ln = Er, Ho) nanomaterials synthesized at room temperature by simple co-precipitation method. Diffraction and spectroscopic studies revealed that these nanomaterials are effectively doped with Ln³⁺ ions in the scheelite lattice. DR UV–vis spectra of these materials exhibit two broad bands in the range of 200–350 nm correspond to MoO₄²⁻ charge transfer, s-p transition of Bi³⁺ ions and sharp peaks due to f-f transition of Ln³⁺ ions. Upconversion luminescence properties of these nanomaterials are investigated under 980 nm excitation. Doping concentration of Er³⁺ and Yb³⁺ ions is optimized to obtain best upconversion photoluminescence in NaBi(MoO₄)₂ nanomaterials and is found to be 5, 10 mol % for Er³⁺, Yb³⁺, respectively. NaBi(MoO₄)₂ nanomaterials co-doped with Er³⁺, Yb³⁺ exhibit strong green upconversion luminescence, whereas Ho³⁺, Yb³⁺ co-doped materials show strong red emission. Power dependent photoluminescence studies demonstrate that emission intensity increases with increasing pump power. Fluorescence intensity ratio (FIR) and population redistribution ability (PRA) of ²H_11/2 → ⁴I_15/2, ⁴S_3/2 → ⁴I_15/2 transitions of Er³⁺ increases with increasing the Yb³⁺ concentration. Also, these values increase linearly with increasing the pump power up to 2 W. It reveal that these thermally coupled energy levels are effectively redistributed in co-doped samples due to local heating caused by Yb³⁺.     

Designing dual-mode luminescence in Er3+ doped Y2WO6 microparticles for anticounterfeiting and temperature measurement

In recent years, rare earth ions doped optical materials have been extensively utilized in anticounterfeiting, temperature measurement, and other fields. However, it is difficult for single-mode photoluminescence to meet the increasingly complex anticounterfeiting needs in practice. In this article, Yb³⁺/Er³⁺ codoped Y₂WO₆ multifunctional microparticles have been designed and prepared, which can emit multimode luminescence and are used for anticounterfeiting and temperature measurement. Under excitation at 254, 365, and 980 nm, Y₂WO₆:Yb³⁺/Er³⁺ microparticles can emit blue, green, and yellow-green luminescence, respectively. The multicolor emission is helpful to improve the security of anticounterfeiting in multimode. In addition, the upconversion, downconversion luminescence, and downconversion lifetime attenuation of this material can be used for fast responsive and noncontact temperature measurement. Among the three temperature measurement methods, the material has the highest sensitivity under the downconversion temperature measurement method, which is 1.25 × 10^–2 K^–1 (at 303 K). The results suggest that the Y₂WO₆:Yb³⁺/Er³⁺ microparticles have excellent applications in the domain of multimode anticounterfeiting and temperature measurement.     

Optical temperature sensor based on upconversion luminescence of Er3+ doped GdTaO4 phosphors

For the development of optical temperature sensor, a series of GdTaO₄ phosphors with various Er³⁺-doping concentrations (0, 1, 5, 10, 25, 35, 50 mol%) were synthesized by a solid-state reaction method. The monoclinic crystalline structure of the prepared samples was determined by X-ray diffraction (XRD). Under excitations of 980 and 1550 nm lasers, the multi-photon-excited green and red upconversion (UC) luminescence emissions of Er³⁺ were studied, and the critical quenching concentration of Er³⁺-doped GdTaO₄ phosphor was derived to be 25 mol%. By changing the pump power of laser, it was found that the two-photon and three-photon population processes happened for the UC emissions of Er³⁺-doped GdTaO₄ phosphors excited by 980 and 1550 nm lasers, respectively. Furthermore, based on the change of thermo-responsive green UC luminescence intensity corresponding to the ²H_11/2 → ⁴I_15/2 and ⁴S_3/2 → ⁴I_15/2 transitions of Er³⁺ with temperature, the optical temperature sensing properties of Er³⁺-doped GdTaO₄ phosphor were investigated under excitations of 980 and 1550 nm lasers by using the fluorescence intensity ratio (FIR) technique. It was obtained that the maximum absolute sensitivity (S_A) and relative sensitivity (S_R) of Er³⁺-doped GdTaO₄ phosphors are as high as 0.0041 K⁻¹ at 475 K and 0.0112 K⁻¹ at 293 K, respectively. These significant results suggest that the Er³⁺-doped GdTaO₄ phosphors are a promising candidate for optical temperature sensor.     

Optical Temperature Sensing Behavior of High‐Efficiency Upconversion: Er3+–Yb3+ Co‐Doped NaY(MoO4)2 Phosphor

A class of Yb³⁺/Er³⁺ co‐doped NaY(MoO₄)₂ upconversion (UC) phosphors have been successfully synthesized by a facile hydrothermal route with further calcination. The structural properties and the phase composition of the samples were characterized by X‐ray diffraction (XRD). The UC luminescence properties of Yb³⁺/Er³⁺ co‐doped NaY(MoO₄)₂ were investigated in detail. Concentration‐dependent studies revealed that the optimal composition was realized for a 2% Er³⁺ and 10% Yb³⁺‐doping concentration. Two‐photon excitation UC mechanism further illustrated that the green enhancement arised from a novel energy‐transfer (ET) pathway which entailed a strong ground‐state absorption of Yb³⁺ ions and the excited state absorption of Yb³⁺–MoO₄^2? dimers, followed by an effective energy transfer to the high‐energy state of Er³⁺ ions. We have also studied the thermal properties of UC emissions between 303 and 523 K for the optical thermometry behavior under a 980 nm laser diode excitation for the first time. The higher sensitivity for temperature measurement could be obtained compared to the previous reported rare‐earth ions fluorescence based optical temperature sensors. These results indicated that the present sample was a promising candidate for optical temperature sensors with high sensitivity.     

Highly Sensitive Optical Thermometry of Yb3+‐Er3+ Codoped AgLa(MoO4)2 Green Upconversion Phosphor

Er³⁺–Yb³⁺ codoped AgLa(MoO₄)₂ phosphors with intense green emission from ²H_11/2/⁴S_3/2 → ⁴I_15/2 transitions and negligible red emission from ⁴F_9/2 → ⁴I_15/2 transition of Er³⁺ were synthesized by sol–gel process. Its temperature sensing performance was evaluated based on the temperature dependence of fluorescence intensity ratio (FIR) of two green emission bands in the range 300–510 K. The maximum sensitivity of AgLa(MoO₄)₂: 0.02Er³⁺/0.4Yb³⁺ is approximately 0.018 K^?1 at 480 K, which is much higher than those of reported samples based on green emissions of Er³⁺. Result suggests that AgLa(MoO₄)₂: Er³⁺/Yb³⁺ has a great potential application in optical temperature sensors.     

NUV light induced visible emission in Er3+-activated NaSrLa(MoO4)O3 phosphors for green LEDs and thermometer

Er³⁺-activated NaSrLa(MoO₄)O₃ phosphors were synthesized by a traditional solid-state reaction technique, which exhibited bright green emissions ascribing to the (²H_11/2, ⁴S_3/2) → ⁴I_15/2 transitions of Er³⁺ ions under 377 nm excitation. The luminescence intensity increased with increasing the Er³⁺ ion concentration and achieved its maximum value when the doping concentration was 4 mol%. Moreover, the critical distance was estimated to be 25.32 Å, and the dipole-dipole interaction played a significant role in NR energy transfer between Er³⁺ ions in NaSrLa(MoO₄)O₃ host lattices. At a forward bias current of 100 mA, the Light Emitting Diode (LED) device emitted a bright green emission with the color coordinate of (0.2547, 0.5996) that can be observed by the naked eye. Besides, based on the thermally coupled levels of ²H_11/2 and ⁴S_3/2, the temperature sensing performances of the prepared phosphors in the temperature range of 303-483 K were studied using the fluorescence intensity ratio technique. The maximum sensor sensitivity was about 0.0150 K⁻¹ when the temperature was 483 K, and the Er³⁺ ion concentration largely influenced the sensor sensitivity of studied samples. Furthermore, the prepared phosphors exhibited excellent water resistance and thermal stability behavior. These characteristics demonstrated that the Er³⁺ activated NaSrLa(MoO₄)O₃ phosphors were dual-functional materials for solid-state illumination and non-contact temperature measurement.