Mobility enhancement by using silk fibroin in F16CuPc organic thin film transistors

High performance n-type F₁₆CuPc organic thin-film transistors (OTFTs) were fabricated on polyethylene terephthalate (PET) using silk fibroin as the gate dielectric. The average field-effect mobility (μ_FE) value in the saturation regime is 0.39 cm² V⁻¹ s⁻¹ approximately one order of magnitude higher than the reported values in the literature. A typical F₁₆CuPc OTFT exhibits an on/off current ratio of 9.3 × 10², a low threshold voltage of 0.65 V, and a subthreshold swing value of 730 mV/decade. The enhancement of μ_FE results from very good crystal quality of F₁₆CuPc on silk fibroin, supported by grazing incidence X-ray diffraction (GIXD) data.     

Hydrated bovine serum albumin as the gate dielectric material for organic field-effect transistors

Bovine serum albumin (BSA) is a natural protein with good hydration ability which contains acidic and basic amino acid residues of ca. 34% in total. In vacuum, pentacene organic field-effect transistors (OFETs) with BSA as the gate dielectric exhibits a field-effect mobility value (μ_FE,sat) of 0.3 cm² V⁻¹ s⁻¹ in the saturation regime and a threshold voltage (V_TH) of ca. −16 V. BSA is easy to be hydrated in air ambient. Electrical properties of BSA in vacuum and hydrated BSA in air ambient are characterized. Similar to polyelectrolyte, hydrated BSA may act the gate dielectric with the formation of electric double-layer capacitors (EDLCs) to improve the device performance. In a relative humidity of 47%, the μ_FE,sat value increases to 4.7 cm² V⁻¹ s⁻¹ and the V_TH reduces to −0.7 V. Generation of mobile ions in hydrated BSA and the formation of EDLCs are discussed.     

The role of water in the device performance of n-type PTCDI-C8 organic field-effect transistors with solution-based gelatin dielectric

Gelatin is a natural protein, which works well as the gate dielectric for N,N-dioctyl-3,4,9,10-perylene tetracarboxylic diimide (PTCDI-C₈) organic field-effect transistors (OFETs). An aqueous solution process was applied to form the gelatin gate dielectric on poly(ethylene terephthalate) (PET) by spin-coating and subsequent casting. The field-effect mobility in the saturation regime (μ_FE,sat) and the threshold voltage (V_T) values of a typical 40 nm PTCDI-C₈ OFET are (0.22 cm² V⁻¹ s⁻¹, 55 V) in vacuum and (0.74 cm² V⁻¹ s⁻¹, 2.6 V) in air ambient. The maximum voltage shift in hysteresis is also reduced from 10 V to 2 V when the operation environment for PTCDI-C₈ OFETs is changed from vacuum to air ambient. Nevertheless, a slight reduction of electron mobility was found when the device was stressed in the air ambient. The change in the device performance has been attributed to the charged ions generation owing to water absorption in gelatin in air ambient.     

Performance comparison of pentacene organic field-effect transistors with SiO2 modified with octyltrichlorosilane or octadecyltrichlorosilane

Performance of pentacene organic field-effect transistors (OFETs) is significantly improved by treatment of SiO₂ with octyltrichlorosilane (OTS-8) compared to octadecyltrichlorosilane (OTS-18). The average hole mobility in these OFETs is increased from 0.4 to 0.8 cm²/Vs when treating the dielectric with OTS-8 versus OTS-18 treated devices. The atomic force microscope (AFM) images show that the OTS-8 treated surface produces much larger grains of pentacene (∼500 nm) compared to OTS-18 (∼100 nm). X-ray diffraction (XRD) results confirmed that the pentacene on OTS-8 is more crystalline compared to the pentacene on OTS-18, resulting in higher hole mobility.     

Operation voltage reduction and gain enhancement in organic CMOS inverters with the TTC/gelatin bilayer dielectric

An air ambient operated organic complementary metal oxide semiconductor (CMOS) inverter has been fabricated on poly(ethylene terephthalate) (PET) using pentacene and N,N-dioctyl-3,4,9,10-perylene tetracarboxylic diimide (PTCDI-C₈) as active layers with a bilayer dielectric of tetratetracontane (TTC) and gelatin. The inverter performance is greatly improved by replacing the gelatin dielectric with the TTC/gelatin bilayer. With the TTC/gelatin bilayer, both types of organic field-effect transistor (OFET) show better pinch-off and current saturation in output characteristics and negligible hysteresis transfer characteristics. The organic CMOS inverter with the TTC/gelatin bilayer dielectric exhibits balanced motilities of 0.5 (pentacene) and 0.3 cm² V⁻¹ s⁻¹ (PTCDI-C₈) with low threshold voltages of −1 (pentacene) and 3 V (PTCDI-C₈). A high static gain of 60 may be achieved with sharp inversion.     

Low-voltage p-channel, n-channel and ambipolar organic thin-film transistors based on an ultrathin inorganic/polymer hybrid gate dielectric layer

A key issue in research into organic thin-film transistors (OTFTs) is low-voltage operation. In this study, we fabricated low-voltage operating (below 3V) p-channel, n-channel and ambipolar OTFTs based on pentacene or/and C₆₀ as the active layers, respectively, with an ultrathin AlO_X/poly(methyl methacrylate co glycidyl methacrylate) (P(MMA–GMA)) hybrid layer as the gate dielectric. Benefited from the enhanced crystallinity of C₆₀ layer and greatly reduced density of electron trapping states at the interface of channel/dielectric due to the insertion of ultrathin pentacene layer between C₆₀ and P(MMA–GMA), high electron mobility can be achieved in present pentacene/C₆₀ heterostructure based ambipolar OTFTs. The effect of the thickness of pentacene layer and the deposition sequence of pentacene and C₆₀ on the device performance of OTFTs was studied. The highest electron mobility of 3.50 cm²/V s and hole mobility of 0.25 cm²/V s were achieved in the ambipolar OTFT with a pentacene (3.0 nm)/C₆₀ (30 nm) heterostructure.     

Comparison of short and long wavelength absorption electron donor materials in C60-based planar heterojunction organic photovoltaics

Buckminsterfullerene, C₆₀-based planar heterojunction (PHJ) organic photovoltaics (OPVs) have been created using a short wavelength absorption (λ_max = 490 nm) electron-donating bis(naphthylphenylaminophenyl)fumaronitrile (NPAFN). NPAFN exhibits a hole mobility greater than 0.07 cm² V⁻¹ s⁻¹ as determined by its field-effect transistor. It can be attributed to such hole mobility that enables a thin layer (<10 nm) NPAFN in PHJ OPV, ITO/NPAFN/C₆₀/bathocuproine/Al. Because of the low lying HOMO energy level (5.75 eV) of NPAFN and relatively high ionization potential ITO (∼5.58 eV), such OPVs exhibit a very high open circuit voltage of ∼1.0 V, relatively high fill factor of 0.60, and a relatively high shunt resistance of 1100 Ω cm⁻², which all compensate for a relatively low short circuit current of 3.15 mA cm⁻² due to the short absorption wavelength and inferred short exciton diffusion length of NPAFN. Altogether, NPAFN OPVs display a power conversion efficiency (η_PC) of 2.22%, which is better than other long wavelength absorption materials in similar PHJ OPVs, such as pentacene (λ_max 670 nm, HOMO 5.12 eV, η_PC 1.50%) and copper phthalocyanine (λ_max 624, 695 nm, HOMO 5.17 eV, η_PC 1.43%).     

Electrical responses of short-channel organic transistor prepared by solution-processed organic crystal wire mask

We report a formation of a solution-grown single crystal wire mask for the fabrication of short-channel organic field-effect transistor with enhanced dynamic response time. The various channel length, ranging from submicrometer to a few micrometers, were obtained by controlling the concentration of solution and processing conditions. We fabricated p- and n-channel bottom-contact organic field-effect transistors using pentacene and PTCDI-C₁₃, respectively, and static and dynamic electrical characteristics of the devices were investigated. The highest and average field-effect hole mobility values were found to be 0.892 cm²/V s and 0.192 cm²/V s, respectively. The load type inverter based on the short-channel transistor connected with a 2 MΩ resistor showed a clear switching response when square wave input signals up to 1 kHz were applied at V_DD = −60 V.     

Synthesis,size-dependent optoelectronic and charge transport properties of thieno(bis)imide end-substituted molecular semiconductors

The synthesis of two new thieno(bis)imide (TBI, N) end functionalized oligothiophene semiconductors is reported. In particular, trimer (NT3N) and pentamer (NT5N) have been synthesized and characterized. Two different synthetic approaches for their preparation were tested and compared namely conventional Stille cross coupling and direct arylation reaction via C–H activation. Theoretical calculations, optical and electrochemical characterization allowed us to assess the role of the π-conjugation extent, i.e., of the oligomer size on the optoelectronic properties of these materials. In both TBI ended compounds, due to the strong localization of the LUMO orbital on the TBI unit, the LUMO energy is almost insensitive to the oligomer size, this being crucial for the fine-tailoring of the energy and the distribution of the frontier orbitals. Surprisingly, despite its short size and contrarily to comparable TBI-free analogues, NT3N shows electron charge transport with mobility up to μ_N = 10⁻⁴ cm² V⁻¹ s⁻¹, while increasing the oligomer size to NT5N promotes ambipolar behavior and electroluminescence properties with mobility up to μ_N = 0.14 cm² V⁻¹ s⁻¹ and to μ_P = 10⁻⁵ cm² V⁻¹ s⁻¹.     

H-aggregation mode in triple-decker phthalocyaninato-europium semiconductors. Materials design for high-performance air-stable ambipolar organic thin film transistors

Two new tris(phthalocyaninato) europium complexes Eu₂(Pc)[Pc(OPh)₈]₂ (1) and Eu₂[Pc(OPh)₈]₃ (2) [Pc = unsubstituted phthalocyaninate; Pc(OPh)₈ = 2,3,9,10,16,17,23,24-octaphenoxyphthalocyaninate], were designed and synthesized. Introduction of different number of electron-withdrawing phenoxy substituents at the phthalocyanine periphery within the triple-decker complexes not only ensures their good solubility in conventional organic solvents, but more importantly successfully tunes their HOMO and LUMO levels into the range of air-stable ambipolar organic semiconductor required on the basis of electrochemical studies over both 1 and 2, meanwhile fine controlling of aggregation mode (H vs. J) in solution-based film for improving OTFT performance is also achieved. Measurements over the OTFT devices fabricated from these sandwich compounds by a solution-based quasi–Langmuir–Shäfer (QLS) method reveal their ambipolar semiconductor nature associated with suitable HOMO and LUMO energy levels. Due to the H-aggregation mode employed by the heteroleptic triple-decker molecules in the QLS film, excellent performances with the electron and hole mobility in air as high as 0.68 and 0.014 cm² V⁻¹ s⁻¹, respectively, have been revealed for the OTFT devices of heteroleptic triple-decker 1. This represents the best performance so far for solution-processable ambipolar single-component phthalocyanine-based OTFTs obtained under ambient conditions. In good contrast, homoleptic analogue 2 prefers to J-type aggregation and this results in relatively lower electron and hole mobility, around 0.041 and 0.0026 cm² V⁻¹ s⁻¹ in air, respectively, for the devices fabricated. In particular, the performance of the devices fabricated based on 1 was found to remain almost unchanged in terms of both the carrier mobilities and on/off ratio even after being stored under ambient for 4 months.     

Pentacene organic thin-film transistors with solution-based gelatin dielectric

Gelatin is a natural protein in the field of food, pharmaceutical and tissue engineering, which works very well as the gate dielectric for pentacene organic thin-film transistors (OTFTs). An aqueous solution process has been applied to form a gelatin thin film on poly(ethylene terephthalate) (PET) or glass by spin-coating and subsequent casting. The device performance of pentacene OTFTs depend on the bloom number (molecular weight) of gelatin. The pentacene OTFT with 300 bloom gelatin as the gate dielectric in air ambient exhibits the best performance with an average field-effect mobility (μ_FE) value of ca. 16 cm² V^?1 s^?1 in the saturation regime and a low threshold voltage of ?1 V. The high performance of the pentacene OTFT in air ambient is attributed to the water resided in gelatin. The crystal quality of pentacene is not the key factor for the high performance.     

A new diketopyrrolopyrrole-based co-polymer for ambipolar field-effect transistors and solar cells

A new thieno[3,2-b]thiophenediketopyrrolopyrrole-benzo[1,2-b:4,5-b′]dithiophene based narrow optical gap co-polymer (PTTDPP-BDT) has been synthesized and characterized for field-effect transistors and solar cells. In field-effect transistors the polymer exhibited ambipolar charge transport behaviour with maximum hole and electron mobilities of 10⁻³ cm² V⁻¹ s⁻¹ and 10⁻⁵ cm² V⁻¹ s⁻¹, respectively. The respectable charge transporting properties of the polymer were consistent with X-ray diffraction measurements that showed close molecular packing in the solid state. The difference in hole and electron mobilities was explained by density functional theory calculations, which showed that the highest occupied molecular orbital was delocalized along the polymer backbone with the lowest unoccupied molecular orbital localized on the bis(thieno[3,2-b]thiophene)diketopyrrolopyrrole units. Bulk heterojunction photovoltaic devices with the fullerene acceptor PC₇₀BM were fabricated and delivered a maximum conversion efficiency of 3.3% under AM1.5G illumination.     

MOS devices with tetragonal ZrO2 as gate dielectric formed by annealing ZrO2/Ge/ZrO2 laminate

A Ge-stabilized tetragonal ZrO₂ (t-ZrO₂) film with permittivity (κ) of 36.2 was formed by depositing a ZrO₂/Ge/ZrO₂ laminate and a subsequent annealing at 600 °C, which is a more reliable approach to control the incorporated amount of Ge in ZrO₂. On Si substrates, with thin SiON as an interfacial layer, the SiON/t-ZrO₂ gate stack with equivalent oxide thickness (EOT) of 1.75 nm shows tiny amount of hysteresis and negligible frequency dispersion in capacitance-voltage (C-V) characteristics. By passivating leaky channels derived from grain boundaries with NH₃ plasma, good leakage current of 4.8 × 10⁻⁸ A/cm² at V_g = V_fb − 1 V is achieved and desirable reliability confirmed by positive bias temperature instability (PBTI) test is also obtained.     

Dibenzothiophene-S,S-dioxide based medium-band-gap polymers for efficient bulk heterojunction solar cells

Medium-band-gap polymers based on indacenodithiophene (IDT) and dibenzothiophene-S,S-dioxide (SO) derivatives, PIDT-SO and PIDT-DHTSO, were synthesized via a microwave assisted Stille polycondensation. The polymers have the maximum absorption ∼500 nm, high absorption coefficients above 0.6 × 10⁻² nm⁻¹, and medium band gaps of ∼2.2 eV. Their hole mobilities are around 2 × 10⁻⁴ cm² V⁻¹ s⁻¹ as measured by field effect transistors. The photovoltaic performances of the polymers were investigated on the inverted bulk heterojunction (BHJ) devices of ITO/PFN/PIDT-DHTSO:PC₇₁BM (1:3, w/w)/MoO₃/Al, and a power conversion efficiency (PCE) of 3.81% with an open-circuit voltage (V_oc) of 0.95 V, a short-circuit current (J_sc) of 8.20 mA cm⁻² and a fill factor (FF) of 48% were achieved. Those results indicated that dibenzothiophene-S,S-dioxide derivatives could be an excellent electron-deficient building block for medium-band-gap electron-donor polymers.     

Pentacene/n-Si heterojunction diodes and photovoltaic devices investigated by I-V and C-V measurements

The forward and reverse current density-voltage (J-V) and capacitance-voltage (C-V) characteristics of pentacene/n⁻-silicon heterojunction diodes were investigated to clarify the carrier conduction mechanism at the organic/inorganic heterojunction. Current rectification characteristics of the pentacene/n⁻-Si junctions can be explained by a Schottky diode model with an interfacial layer. The diode parameters such as Schottky barrier height and ideality factor were estimated to be 0.79-1.0 eV and 2.4-2.7, respectively. The C-V analysis suggests that the depletion layer appears selectively in the n⁻-Si layer with a thickness of 1.47 μm from the junction with zero bias and the diffusion potential was estimated at 0.30 eV at the open-circuit condition. The present heterojunction allows the photovoltaic operation with power conversion efficiencies up to 0.044% with a simulated solar light exposure of 100 mW/cm².     

Charge trapping and interface characteristics in normally-off Al2O3/GaN-MOSFETs

Normally-off GaN-MOSFETs with Al₂O₃ gate dielectric have been fabricated and characterized. The Al₂O₃ layer is deposited by ALD and annealed under various temperatures. The saturation drain current of 330 mA/mm and the maximum transconductance of 32 mS/mm in the saturation region are not significantly modified after annealing. The subthreshold slope and the low-field mobility value are improved from 642 to 347 mV/dec and from 50 to 55 cm² V⁻¹ s⁻¹, respectively. The I_D-V_G curve shows hysteresis due to oxide trapped charge in the Al₂O₃ before annealing. The amount of hysteresis reduces with the increase of annealing temperature up to 750 °C. The Al₂O₃ layer starts to crystallize at a temperature of 850 °C and its insulating property deteriorates.     

A simple droplet pinning method for polymer film deposition for measuring charge transport in a thin film transistor

Thin-film field-effect transistors (FETs) are widely used to evaluate charge transport properties of semiconducting polymers. Discovery of high performance materials require design and synthesis of new polymers. However, most polymers require multi-step synthesis and are difficult to be obtained in a large scale for comprehensive device evaluations. Here, we report a simple method to cast semiconducting polymer films from solutions with polymer concentration as low as 0.5 mg/mL, which is substantially less than typical values (∼10 mg/mL) used in conventional spin coating method. Here, we demonstrate that using this method, our cast films of a previously-reported polymer (PDPP-TT2T) exhibited field-effect mobility (μ_hole = 0.89 ± 0.13 cm² V⁻¹ s⁻¹, μ_e = 0.025 ± 0.005 cm² V⁻¹ s⁻¹), which is comparable to the reported values using the same device geometry. Furthermore, we extend this method to examine cast films of a pair of polymers (PDPP-3T-Ref, PDPP-3T-Si) to study the effect of siloxane substitution in the side chains on the molecular packing and their subsequent FET performance. We observed that shorter π-stacking distance (3.61 Å) for the siloxane-terminated polymer, when compared to that for the reference polymer (3.73 Å), resulted in improved FET performance (e.g., μ_hole = 0.63 ± 0.046 cm² V⁻¹ s⁻¹ for PDPP-3T-Si vs μ_hole = 0.17 ± 0.062 cm² V⁻¹ s⁻¹ for PDPP-3T-Ref). Taken together, this work presents an efficient alternative film-casting approach to produce polymer FETs that consumes much less material for their fabrication, lending viability for evaluation of various polymeric materials.     

High-mobility pentacene thin-film transistor by using LaxTa(1−x)Oy as gate dielectric

Pentacene organic thin-film transistors (OTFTs) using La_xTa_(1−x)O_y as gate dielectric with different La contents (x = 0.227, 0.562, 0.764, 0.883) have been fabricated and compared with those using Ta oxide or La oxide. The OTFT with La_0.764Ta_0.236O_y can achieve a carrier mobility of 1.21 cm² V⁻¹s⁻¹s, which is about 40 times and two times higher than those of the devices using Ta oxide and La oxide, respectively. As supported by XPS, AFM and noise measurement, the reasons lie in that La incorporation can suppress the formation of oxygen vacancies in Ta oxide, and Ta content can alleviate the hygroscopicity of La oxide, resulting in more passivated and smoother dielectric surface and thus larger pentacene grains, which lead to higher carrier mobility.     

Interface optimization using diindenoperylene for C60 thin film transistors with high electron mobility and stability

C₆₀-based organic thin film transistors (OTFTs) with high electron mobility and high operational stability are achieved with (1 1 1) oriented C₆₀ films grown by using template effects of diindenoperylene (DIP) under layer on the SiO₂ gate insulator. The electron mobility of the C₆₀ transistor is significantly increased from 0.21 cm² V⁻¹ s⁻¹ to 2.92 cm² V⁻¹ s⁻¹ by inserting the template-DIP layer. Moreover much higher operational stability is also observed for the DIP-template C₆₀ OTFTs. A grazing incidence X-ray diffraction and ultrahigh-sensitivity photoelectron spectroscopy measurements indicate that the improved electron mobility and stability arise from the decreased density of trap states in the C₆₀ film due to increased (1 1 1) orientation of C₆₀-grains and their crystallinity on the DIP template.     

Stable Delocalized Singlet Biradical Hydrocarbon for Organic Field‐Effect Transistors

Delocalized singlet biradical hydrocarbons hold promise as new semiconducting materials for high‐performance organic devices. However, to date biradical organic molecules have attracted little attention as a material for organic electronic devices. Here, this work shows that films of a crystallized diphenyl derivative of s‐indacenodiphenalene (Ph₂‐IDPL) exhibit high ambipolar mobilities in organic field‐effect transistors (OFETs). Furthermore, OFETs fabricated using Ph₂‐IDPL single crystals show high hole mobility (μ_h = 7.2 × 10^?1 cm² V^?1 s^?1) comparable to that of amorphous Si. Additionally, high on/off ratios are achieved for Ph₂‐IDPL by inserting self‐assembled mono­layer of alkanethiol between the semiconducting layer and the Au electrodes. These findings open a door to the application of ambipolar OFETs to organic electronics such as complementary metal oxide semiconductor logic circuits.