共查询到20条相似文献,搜索用时 281 毫秒
1.
2.
空气流量为30万m3/h的离心空压机,其出口压力变送器和入口压差变送器因为使用环境温度超极限而发生故障,导致空压机卸载。通过改进空压机现场压力变送器安装位置,降低空压机本体对变送器的热辐射影响,使变送器的使用环境温度满足其极限环境温度要求,以降低空压机现场变送器的故障率,提高变送器的可靠性,确保空压机安全运行。介绍变送器安装位置的改进情况及其效果。 相似文献
4.
《中国计量学院学报》2017,(2):169-175
针对空压机进气增压可提高大功率燃料电池发动机性能和功率密度,但空压机超高速电机转子-轴承系统存在共振失稳乃至断轴的实际工程问题.本文采用有限元法建立空压机高速电机轴承-转子系统动力学模型,基于ANSYS软件对某超高速永磁电机转子进行动力学仿真,分析某燃料电池空压机高速电机转子-轴承系统的临界转速,揭示轴承刚度、轴承位置以及转轴质量等因素对临界转速的影响规律,并提出改善措施.结果显示,增大轴承刚度、适当减小轴承跨距以及减轻转轴的质量可以有效地增加转子轴承系统的临界转速. 相似文献
5.
6.
空压机站为工业企业提供压缩空气,是重的动力来源。为使空压机能提供稳定的压力,分析了传统工频空压机供气系统中存在的缺点,提出了空压机变频改造方案,计算了变频改造后的节能效果,对式空压机变频改造控制以达到节能降耗目的进行了可行性研究,并做出了经济效益分析。 相似文献
7.
压缩空气系统是火力发电机组中非常重要的公用系统,其主要作用是为机组自动控制系统中的气动执行机构、吹扫及冷却系统提供安全可靠的气源。因此,空压机的运行工况直接关系到机组的安全稳定运行。但是,喘振是离心式空压机的固有属性,如何避免离心式空压机在运行过程中发生喘振,使空压机运行在稳定工况区是空压机控制系统需要解决的问题。本文采用OMRONCJ系列PLC控制器,对系统压力和流量采用双PID控制,利用入口门、旁路门“快开慢关”原则,有效的避免了喘振的发生。该控制系统已经在华能国际上安电厂应用,运行结果良好。 相似文献
8.
介绍了空分设备透平空压机降低能耗的方法(技术改造,提高等温效率;减小吸气阻力、降低各段进气温度、随需氧量相应改变空气量;适当降低设备操作压力、降低单位产品的空气消耗量等),着重对空压机气量小的情况作了分析。列出了DA350-61型空压机改造前后的参数对比。最后提出应加强巡回检查与维修。图1表2。 相似文献
9.
本文介绍在空压机自动控制系统的基础上再利用电磁环、水位传感器和电磁阀改造的压风机冷却系统自动补水装置取代人工补水和停水,来实现空压机冷却水循环保护功能的方法和优点,用可靠、安全、维修简便、成本低及降低人工劳动强度的空压机冷却效果,实现空压机安全运转的方法。又进一步完善了空压机的无人值守的目的。 相似文献
10.
一、前言 我院动力实验室空压站有两台日本进口的OPT-307对称平衡卧式空压机。其单机排量为43.3m~3/min、压力7.0kgf/cm~2,电机转速585r/min。空压站布置见图1。 相似文献
11.
The helium supply and outlet lines of a rotating superconducting magnet can be arranged so that the self-pumping mechanism due to the centrifugal forces effects a pressure and temperature decrease in the rotor. Several parameters such as speed of rotation, diameter of the rotor, outlet pressure, and quality of the helium supplied to the rotor have been modified in a computer study. The calculation shows that the self-pumping mechanism is so effective that even the temperature at the periphery of a large scale rotor decreases with increasing speed of rotation. This refrigeration cycle appears to have a strong self-regulating characteristic. 相似文献
12.
本文介绍了一种内燃机发电机组运行状态信号采集电路,包括冷却水温,机油温度,机油压力,油门位置上下限以及转速信号的采集,文中给出了较详细的硬件电路,并进行了简要分析说明,该电路可用于微机自动控制系统,且除转速外,其它信号均采用开关量形式,采集简单,便于软件编程。该电路也可用于其它需开关量控制的场合,具有一定的通用性。 相似文献
13.
目的研究20~#钢连续驱动摩擦焊接过程工艺参数对焊接过程温度场和变形行为的变化规律。方法基于ABAQUS有限元软件二次开发环境,建立了20~#钢连续驱动摩擦焊接过程中的完全热-结构耦合模型。通过对比模拟和实验获得的焊接温度场、轴向缩短量和飞边形貌,对模型进行了验证。研究了工艺参数对摩擦焊接过程温度场与大变形行为和接头组织与性能的影响规律。结果在不稳定摩擦阶段,峰值温度出现在外表面附近。在稳定摩擦阶段,峰值温度稳定在距焊缝中心约2/3半径位置。接头温度的升高速度随着摩擦压力和转速的增大而增大,摩擦压力和转速对稳定阶段温度场的影响很有限;经过顶锻阶段之后摩擦面温度分布更加均匀,顶锻力越大在接头相同的位置温度越低,顶锻力越大轴向缩短量越大。结论所建立的完全热-结构耦合模型可以模拟20~#钢连续驱动摩擦焊接过程的塑性变形过程,在不稳定摩擦阶段,摩擦压力和转速对温度场和变形的影响较大。在稳定摩擦阶段,摩擦压力和转速对温度场的影响不显著。顶锻阶段轴向缩短量随着摩擦压力、转速和顶锻压力的增大而增加。 相似文献
14.
在构建的汽车水泵总成半消声室噪声测试系统中,针对汽车水泵的工作噪声特性,确立了企业水泵总成噪声测试规范,用于评价汽车水泵总成件的噪声性能。测试表明:正常水泵工作噪声声压谱在400 Hz~10 kHz范围内呈现高低两个单频峰值结构噪声源,高转速下水泵主要噪声源为宽频涡流噪声。转速和防冻液温度对工作噪声影响较大,低速、高温工况下的工作噪声应为水泵噪声主要质量控制点。水泵工作噪声合格性评判除包括稳态工作转速下测量表面总声功率和声功率谱外,还需控制其提速过程中的总声功率,以防止结构共振噪声。 相似文献
15.
汪俊勇 《制冷与空调(北京)》2012,(3):42-45
针对一种能在低温环境下正常运行的空调系统进行系统分析。研究结果表明,在空调系统的排气管上增加一个压力开关就可以实现低温制冷功能:将压力开关的通断信号传递到控制调速板上,通过调速板控制室外风机的转速,当系统压力低时降低室外风机转速,当系统压力高时提高室外风机转速。通过控制室外风机转速实现低温制冷的方案是可行的,不仅可靠性能够得到保证,而且成本比现有产品低200元左右,具有很强的实用性。 相似文献
16.
本研究选择有限容积法, 采用Fluent软件对KH2PO4(KDP)晶体在不同转速下成帽过程的温度场及速度场分布进行了数值模拟。晶体转速较低(9 r/min)时, 晶体附近温度分布比较均匀, 相应的晶体只出现一个帽区, 但温度较高, 成帽较慢; 晶体转速较高(55和77 r/min)时, 温度分布也比较均匀, 所以晶体也只有一个帽区, 此时温度较低, 成帽较快; 晶体转速介于两者之间时, 温度分布出现扰动, 晶体成帽同时出现两个或多个帽区, 成帽速度介于两者之间。在所模拟晶体转速范围内, 较高转速77 r/min是晶体帽区恢复的最优转速。 相似文献
17.
18.
19.
Afshin Taghizadeh Seyed Hassan Hashemabadi Esmaeil Yazdani Soheil Akbari 《Granular Matter》2018,20(3):56
Hydrodynamic behavior of two dimensional horizontal rotating drum was studied by using finite volume method and granular kinetic theory. In this work, the effects of the different parameters such as rotation speed, restitution coefficient and particle size on the hydrodynamic and especially on the granular temperature of particles were investigated. At first, the results of present work were verified with previous experimental results. Packing limit of 0.6 and restitution coefficient of 0.95 with Gidaspow inter-phase momentum coefficient showed the good agreement with experimental works. It is found that by increasing the restitution coefficient, the granular temperature at different depth of bed increased and affected the hydrodynamic behavior of the bed. Also, particle size and rotation speed directly changed the granular temperature. Moreover, augmentation of the rotation speed leads to increasing the repose angle which caused better mixing of bed, granular temperature rising and consequently particle velocity alteration in the bed. 相似文献
20.
Rashid HA Heinämäki J Antikainen O Yliruusi J 《Drug development and industrial pharmacy》1999,25(5):605-611
Preparation of microcrystalline cellulose (MCC) beads with a laboratory-scale centrifugal granulating apparatus was studied, and the pharmaceutical quality of the beads was characterized with respect to the subsequent drug layering. Five process parameters of potential importance, including rotor rotation speed X1, slit air X2, spray air pressure X3, spray air rate X4, and height of nozzle setting X5, were evaluated using a fractional factorial design (FFD 2(5-2)) as the experimental design. The responses evaluated were expected yield, mean size, size distribution, shape characteristics (including roundness, circularity, elongation, rectangularity, and modelx), and friability. All five process parameters studied were found to have an influence on the selected properties of the beads, but the effects of rotor rotation speed, slit air flow rate, and spray air rate were statistically significant (p < .05). The effect of the rotor rotation speed was found to be the most potent on all the responses studied. The results also show some significant interactions between the parameters tested. The most significant interactions were between rotor rotation speed and slit air, rotor rotation speed and spray air, and slit air and spray air. 相似文献