瞬态热线法导热系数测量的数值模拟

利用有限元方法对瞬态热线法导热系数测量进行了数值模拟,对各种因素如加热功率、热线半径以及实验温度等对测量过程的影响进行了分析,并将模拟得到的温升曲线与实验测量得到的温升曲线进行了比较,结果表明:通过选择适当的参数值,模拟曲线可以与实测曲线吻合得很好,实验值与模拟值的偏差小于实验结果的不确定度.本结果的获得对进一步理解瞬态热线法导热系数测量过程,提高导热系数测量技术水平具有借鉴意义.     

Simultaneous measurements of thermal conductivity and thermal diffusivity of liquids under microgravity conditions

A transient short-hot-wire technique is proposed and used to measure the thermal conductivity and thermal diffusivity of liquids simultaneously. The method is based on the numerical evaluation of unsteady heat conduction from a wire with the same length diameter ratio and boundary conditions as those in the experiments. To confirm the applicability and accuracy of this method. Measurements were made for five sample liquids with known thermophysical properties and were performed under both normal gravity and microgravity conditions. The results reveal that the present method determines both the thermal conductivity and the diffusivity within 2 and 5%. respectively. The microgravity experiments clearly indicate that even under normal gravity conditions, natural-convection effects are negligible for at least l s after the start of heating. This method would be particularly suitable for a valuable and expensive liquid, and has a potential for application to electrically conducting and or corrosive liquids when the probe is effectively coated with an insulating and anticorrosive material. Paper presented at the Fourth Asian Thermophysical Properties Conference, September 5–8, 1995, Tokyo, Japan.     

A transient hot-wire method for measuring the thermal conductivity of gases and liquids

In this paper we describe a version of a transient hot-wire apparatus which employs an integrating digital voltmeter to measure the bridge out-of-balance signal. The integrating period of the voltmeter is variable and is routinely set equal to one 60-Hz power-line cycle, 16.67 ms. Use of measurement or integration periods less than an integral multiple of the power-line period results in substantially more electronic noise and a significant degradation in experimental precision. A correction to the working equation which accounts for the integration of the out-of-balance signal is also presented. The precision of the digital voltmeter used with the apparatus is ±0.1 V, which translates into an ultimate precision of ±0.03 mK in the measured temperature rise. In practice the precision in the temperature rise is typically ±0.3 mK, which represents a moderate improvement over the precision generally obtained with transient techniques employing automatic bridge balancing schemes. Although the current apparatus is designed principally for measurements of the thermal conductivity of liquids, it can been used for gas-phase measurements, with some decrease in accuracy due to the somewhat larger heat capacity correction which must be applied to the temperature rise measurements. The operation of the instrument was verified by measuring the thermal conductivities of toluene and nitrogen. Preliminary data are presented for the new environmentally acceptable fluorocarbons such as R-134a (CF₃CH₂F), R-123 (CHCl₂CF₃), and R-141b (CCl₂FCH₃).Paper presented at the Tenth Symposium on Thermophysical Properties, June 20–23, 1988, Gaithersburg, Maryland, U.S.A.     

Absolute measurements of the thermal conductivity of alcohols by the transient hot-wire technique

New absolute measurements of the thermal conductivity of methanol, ethanol, propanol, butanol, pentanol, and hexanol at atmospheric pressure and in the temperature range 290–350 K are reported. The overall uncertainty in the reported thermal conductivity data is estimated to be better than ±0.5%, an estimate confirmed by the measurement of the thermal conductivity of water. The measurements presented in this paper have been used to develop a consistent theoretically based correlation for the prediction of the thermal conductivity of alcohols. The proposed scheme, based on an extention of the rigid-sphere model, permits the density dependence of the thermal conductivity of alcohols, for temperatures between 290 and 350 K and atmospheric pressure, to be represented successfully by an equation containing just one parameter characteristic of the fluid at each temperature.Paper presented at the Tenth Symposium on Thermophysical Properties, June 20–23, 1988, Gaithersburg, Maryland, U.S.A.     

Radiative heat transfer in transient hot-wire measurements of thermal conductivity

New measurements of the thermal conductivity of liquid toluene between 300 and 550 K have been used to study the importance of radiative heat transfer when using the transient hot-wire technique. The experimental data were used to obtain the radiation correction to the hot-wire temperature rises. Radiationcorrected values of thermal conductivity are reported. This study shows that the transient hot-wire method is much less affected by radiation than steady-state techniques.     

Establishment of accuracy limits and standards for comparative thermal conductivity measurements

New techniques have been developed for reducing thermal conductivity data from thermal comparative measurements. The first of these techniques is based on making a Taylor-series expansion of the stack centerline temperature profile. The result is an expression giving the ratio of sample to reference conductivities at any temperature as a function of measured quantities, the stack thermocouple readings and stack element thicknesses. The conventional formula presently used to reduce comparative conductivity data is shown to be a special result of the general analysis. A second technique involves the use of linear least-squares (LS) techniques to derive both the sample and the reference conductivities from the measured data. The LS technique provides the coefficients for a polynomial temperature expansion of the reference and sample conductivities directly. Use of the new techniques is illustrated in a reduction of some comparative data on the conductivities of Pyrex 7740 and Pyroceram 9606. It is shown that a highly self-consistent pair of conductivity functions can be derived for these two commonly used reference materials if the conductivity vs temperature relation for Pyrex is modified slightly from its recommended value. The Pyroceram conductivity results from the comparative measurements are in good agreement with a conductivity derived from pulse diffusivity and differential scanning calorimetry measurements and also in good agreement with the recommended Pyroceram conductivity function.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

Determination of thermal conductivity from specific heat and thermal diffusivity measurements of plasma-sprayed cermets

The thermal conductivities of three plasma-sprayed cermets have been determined over the temperature range 23–630°C from the measurement of the specific heat, thermal diffusivity, and density. These cermets are mixtures of Al and SiC prepared by plasma spray deposition and are being considered for various applications in magnetic confinement fusion devices. The samples consisted of three compositions: 61 vol% Al/39 vol% SiC, 74vol% Al/26vol% SiC, and 83 vol% Al/17 vol% SiC. The specific heat was determined by differential scanning calorimetry through the Al melt transition up to 720°C, while the thermal diffusivity was determined using the laser flash technique up to 630°C. The linear thermal expansion was measured and used to correct the diffusivity and density values. The thermal diffusivity showed a significant increase after thermal cycling due to a reduction in the intergrain contact resistance, increasing from 0.4 to 0.6 cm²·^–1 at 160°C. However, effective medium theory calculations indicated that the thermal conductivities of both the Al and the SiC were below the ideal defect-free limit even after high-temperature cycling. The specific heat measurements showed suppressed melting points in the plasmasprayed cermets. The 39 vol% SiC began a melt endotherm at 577°C, which peaked in the 640–650°C range depending on the sample thermal history. Chemical and X-ray diffraction analysis indicated the presence of free silicon in the cermet and in the SiC powder, which resulted in a eutectic Al/Si alloy.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

A New Pulse Hot Strip Sensor for Measuring Thermal Conductivity and Thermal Diffusivity of Solids

The pulse hot strip method is a newly developed dynamic method to measure the thermal conductivity and thermal diffusivity of solids. It is based on monitoring the temperature response of a sample to a very short heat pulse liberated by a strip heat source. The instrument's uncertainty is estimated to be less than 3% for both quantities.     

Simultaneous measurement of thermal conductivity and thermal diffusivity of solids by the parallel-wire method

An improved parallel-wire technique for simultaneous measurement of thermal conductivity and thermal diffusivity is presented. The deviation between experimental results and recommended (or another author's) values is less than 5% for fused quartz and refractory brick.     

A computer-controlled transient needle-probe thermal conductivity instrument for liquids

A computerized system utilizing the transient needle-probe technique has been developed for thermal conductivity measurements on solids and liquids. Thermal conductivities are determined to an accuracy of better than 5%. The instrument is unique in that it uses off the shelf components such as a personal computer and analog-to-digital conversion devices, together with software developed in our laboratory. The initial expense and time required to begin measurements are less than 20% of those for normal transient hot-wire measurements. Typical results are presented for liquid tertiary butyl alcohol, 1-methylnaphthalene, and glycerin.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.     

热针法瞬态测量热物性研究

该文从一维圆柱面传热模型的定解问题出发,分析热线法测量材料热导率的局限性,推证热针法瞬态测量材料热物性的基本原理、热扩散系数和热导率的计算公式,设计和开发针式热物性瞬态测量的软硬件,试制SHT-C针式热物性瞬态测量仪,实现对材料热物性的瞬态测量,并实测证明该测量仪有很好的重复性和实用价值.     

瞬态热线法液体导热系数测试系统的研制

根据瞬态热线法测量导热系数的原理,研制了测量装置和数据采集系统.利用阳极氧化的方式,在热线表面进行绝缘处理,使其能够适用于导电性或者极性物质的导热系数的研究.为了检验该系统的性能,在常温常压下对蒸馏水的导热系数进行了测量.测试结果表明,该系统能够满足导热系数测试的需要.     

Comparison of thermal conductivity data for partially stabilized zirconia with values derived from thermal diffusivity results

The thermal conductivity of partially stabilized zirconia was measured over the temperature range 320–1273 K using the radial heat flow method. The data have an absolute uncertainty of about ±2% and repeat measurements showed no evidence of changes in the thermal conductivity at high temperatures. This also was true for the thermal diffusivity data, which were obtained in vacuum over the temperature range 300–1473 K. Both sets of thermal conductivity data pass through minima at high temperatures. Quantitative differences were observed in the temperatures and thermal conductivities of the two minima. The results were analyzed by assuming parallel conduction by phonons and photons, and the phonon component was identified by fitting lower-temperature data. Extrapolating this curve allowed identification of the photon contribution to the thermal conductivity at high temperatures. The photon contribution approached a T ³ function and was larger in the thermal conductivity specimens. The difference in the photon contributions correlates with changes in the optical properties of the samples produced during the high temperature measurments.     

Thermal-wave resonant-cavity measurements of the thermal diffusivity of air: A comparison between cavity-length and modulation-frequency scans

The application of a thermal-wave resonant cavity to thermal-diffusivity measurements of gases has been investigated. The cavity was constructed using a thin aluminum foil wall as the intensitv-modulated laser-beam oscillator source opposite a pyroclectric polyvilidene fluoride wall acting as a signal transducer. Theoretically, cavity-length and modulation-frequency scans both produce resonance-like extrema in lock-in in-phase and quadrature curses. These extrema can be used to measure the thermal diffusivity of the gas within the cavity. It was found experimentally that one can obtain. very accurate and reproducible measurements of the thermal diffusivity of the gas by using simple cavity-length scanning without any signal normalization procedure. rather than traditional modulation-frequency scanning; normalized by the frequency-dependent transfer function of the instrumentation. By scanning the cavity length, the thermal diffisivity of room air at 299 K was measured with three-significant figure precision as 0.216±11.001 cm²·s^–1, with a standard deviation 0.5%. Only two significant figure accuracy could be obtained by scanning the frequency: 0.22±0.03 cm²·s^–1, with a standard deviation of 14%. Cavity-length scanning consistently exhibited a much higher signal-to-noise ratio.     

The thermal conductivity of some alkyl ethers and alkanones

New absolute measurements, by the transient hot-wire technique, of the thermal conductivity of some alkyl ethers and alkanones are presented. The alkyl ethers studied are tert-butyl methyl ether, di-iso-propyl ether and di-butyl ether, while the alkanones studied are 2-butanone, 4-methyl pentan-2-one, and 2-octanone. The temperature range examined was 295–350 K, and the pressure atmospheric. The overall uncertainty in the reported thermal conductivity data is estimated to be better than ±1%, an estimate confirmed by the measurement of the thermal conductivity of water.     

材料热扩散率的非稳态测量与应用

热扩散率是材料热物性中一个非常重要的参数。在材料热扩散率的测试中,主要是利用非稳态方法进行测量。非稳态测量方法具有测量周期短、测试方便、结果准确等优点。主要对常用的5种利用非稳态测试材料热扩散率的方法进行了阐述,详细介绍了它们的工作原理、方法特点以及近几年来的科研成果。同时,列举了目前热扩散率测试的一些常用产品和相关测试标准。最后,对热扩散率测试的未来发展趋势进行了展望。     

Compression work using the transient hot-wire method

A new treatment of the effect of the work of compression upon thermal conductivity measurements by the transient hot-wire technique is presented. The new analysis improves upon those given earlier and leads to quite a different result. The result makes it clear that the dilute gaseous state need not be excluded from the range of thermodynamic states in which accurate measurements are made owing to this effect, in contrast to the conclusions of earlier work.     

Accurate measurement of the thermal conductivity and thermal diffusivity of toluene andn-heptane

Accurate and simultaneous measurements of the thermal conductivity and thermal diffusivity of toluene andn-heptane were made with an improved transient hot-wire method by using a transfer function having a feedback loop, in the temperature range of 0 to 45°C at atmospheric pressure. The accuracy of the empirical equations as a function of temperature is estimated to be 0.4 to 0.5% for the thermal conductivity and about 4% for the thermal diffusivity. Paper presented at the Fourth Asian Thermophysical Properties Conference, September 5–8, 1995, Tokyo, Japan.     

A noncontact method for measuring thermal conductivity and thermal diffusivity of anisotropic materials

A noncontact method for measuring the thermal conductivity and thermal diffusivity of anisotropic materials is proposed. This method is based on the fact that the surface temperature variation with time depends on the thermal properties of the material when its surface is heated locally. The three-dimensional transient heat conduction equation in the material is solved numerically. The dimensionless average surface temperature variations are obtained along each principal axis: that is, thex andy axes. The relation between the dimensionless temperature and the Fourier number is expressed by a polynomial equation and used as a master plot, which is a basic relation to be compared with measured temperature variation. In the experiments, the material surface is heated with a laser beam and the surface temperature profiles are measured by an infrared thermometer. The measured temperature variations with time are compared with the master plots to yield the thermal conductivity λ _x and thermal diffusivityx _v in thex direction and the thermal conductivity ratioE _xy (=λ _y λ _x ) simultaneously. To confirm the applicability and the accuracy of the present method, measurements were performed on multilayered kent-paper, vinyl chloride, and polyethylene resin film, whose thermal properties are known. From numerical simulations, it is found that the present method can measure the thermophysical properties λ _x , α _x andE _xy within errors of ±6, ±22, and ±5%, respectively, when the measuring errors of the peak heat flux, the heating radius, and the surface temperature rise are assumed to be within ±2, ±3%, and ±0.2 K, respectively. This method could be applied to the measurement of thermophysical properties of biological materials.     

A transient hot-wire instrument for thermal conductivity measurements in electrically conducting liquids at elevated temperatures

This paper describes a novel type of transient hot-wire cell for thermal conductivity measurements on electrically conducting liquids. A tantalum wire of 25 m. diameter is used as the sensing element in the cell, and it is insulated from the conducting liquids by an anodic film of tantalum pentoxide, 70 nm thick. The cell is suitable for measurements on conducting liquids at elevated temperatures. The results of test measurements on liquid water at its saturation vapor pressure are reported in order to confirm the correct operation of the thermal conductivity cell. The data, which have an estimated accuracy of ±3%, depart by less than ±1.8% from the correlation proposed by the International Association for the Properties of Steam. Results are also presented for concentrated aqueous solutions of lithium bromide, which are frequently used in absorption refrigerator cycles.