一种新型垂直极化同轴波导缝隙天线

结合波导缝隙和同轴线结构,提出了一种新型同轴波导缝隙结构实现天线小型化。首先,分析了同轴波导缝隙天线内金属摆线上的电流分布,改进了缝隙形式和摆线设计;然后,利用HFSS软件建立不同缝隙数目的同轴波导缝隙天线模型进行仿真,对比分析驻波带宽和方向图带宽;最后,建立不同缝隙数目的同轴波导缝隙天线有限阵列,对比分析阵列中天线增益和效率。     

基于光子晶体的多频微带缝隙天线的设计与仿真

在普通微带缝隙天线介质基板内引入光子晶体结构,设计了一种基于PBG结构的多频微带缝隙天线,采用平面波展开法对该天线进行了理论分析,并用HFSS 10.0对该天线进行了仿真.与传统的微带缝隙天线相比,PBG结构的引入改善了微带缝隙天线的辐射特性及多频工作性能.该天线可以用于跳频通信系统中.     

表面波放电狭缝天线辐射电磁场的三维数值分析

针对平板型表面波放电等离子体源,建立了表面波放电狭缝天线辐射电磁波模型,对狭缝天线辐射电磁场分布进行了三维数值计算,并与表面波电磁场进行对比分析,讨论了平板型表面波放电机理。结果表明:整个狭缝天线阵激发的电磁场是每个狭缝天线激发电磁场的线性叠加;狭缝天线阵直接激发的电磁场强度在临近波导壁面处很大,并且随着空间距离的增大迅速衰减;狭缝天线阵直接激发和表面波的电场均远大于各自的磁场,分析电、磁场对带电粒子的力作用时可以忽略磁场力的作用;表面波电磁场远大于狭缝天线阵直接辐射的电磁场,强电磁场范围也远大于狭缝天线阵直接激发的强电磁场范围,等离子体有增强电磁场强度、扩大强电磁场范围的作用。     

Circularly-Polarized Wide Slot Antenna Loaded With a Parasitic Patch

A design is described of a broadband circularly-polarized (CP) slot antenna. A conventional annular-ring slot antenna is first analyzed, and it is found that two adjacent CP modes can be simultaneously excited through the proximity coupling of an L-shaped feed line. By tuning the dimensions of this L-shaped feed line, the two CP modes can be coupled together and a broad CP bandwidth is thus formed. The design method is also valid when the inner circular patch of the annular-ring slot antenna is vertically raised from the ground plane. In this case, the original band-limited ring slot antenna is converted into a wide-band structure that is composed of a circular wide slot and a parasitic patch, and consequently the CP bandwidth is further enhanced. For the patch-loaded wide slot antenna, its key parameters are investigated to show how to couple the two CP modes and achieve impedance matching. The effects of the distance between the parasitic patch and wide slot on the CP bandwidth and antenna gain are also presented and discussed in details.      

人体中心网络微带缝隙天线设计和研究

设计了一款小型微带缝隙天线.通过电磁仿真软件CST的参数优化功能,对微带缝隙天线缝隙的长度、宽度、馈电点等参数进行优化,得到了工作频率为2.45GHz,带宽100 MHz、阻抗匹配良好、辐射效率较高的用于人体中心网络的微带缝隙小型天线,根据仿真设计,制作了天线,测试结果和仿真结果吻合较好.     

Broadband printed ring-slot array with circular polarisation

A novel design of a printed ring-slot antenna with circular polarisation (CP) is first proposed. The CP radiation of the slot antenna is achieved by a series microstrip-line feed configuration. Using the single CP slot antenna as an array element, the 1times2 and 2times2 slot arrays are constructed and measured. To obtain wider CP bandwidth, phase sequential rotation technique is applied to the feed network of these printed slot arrays. The experimental results show that the 2times2 slot array antenna is capable of 15% bandwidth for an axial ratio of less than 3 dB     

Size reduction of cavity-backed slot antennas

A technique for reducing the dimensions of the cavity of a cavity-backed slot antenna (CBSA) is presented, which facilitates proper fabrication and integration of miniaturized slot antennas on multilayer substrates. This is accomplished by replacing the solid metal around the traditional slot antennas with a specific metallic pattern that can be viewed as a series of parallel strip lines placed around the slot antenna. This metallic pattern is then modified by designing the parallel strips in a compact fashion to reduce the overall antenna dimensions and obtain a reduced-size CBSA. It is shown that, for a simple straight slot antenna, the overall occupied volume of the modified cavity backing the slot antenna can be reduced by more than 65% without affecting the high radiation efficiency of the antenna. A number of traditional cavity backed slot antennas and the proposed modified CBSAs are designed, fabricated, and measured. The reduced-size CBSAs show a very low input VSWR, low cross-polarized radiation levels, and high radiation efficiency. Despite their small ground plane size, the proposed cavity backed slot antennas have front-to-back ratio (FTBR) values in the range of 6-7 dB.     

Broadband circularly-polarised slot antenna array

A stacked slot antenna is proposed and studied to improve the performance of a circularly-polarised (CP) annular-ring slot antenna that has the disadvantages of a narrow bandwidth, a lower gain and bidirectional radiation. The stacked antenna structure is composed of a circular wide slot, a parasitic patch and a metallic reflector, and its CP radiation is excited through the proximity coupling of an L-shaped microstrip line. A 4 times 4 array using the stacked slot antenna as an element is also developed and designed at X-band. Details of the antenna design and obtained results are presented.     

Small annular slot antenna with capacitor loading

A small-size annular slot antenna with miniaturised slot shrunk by a loaded capacitor has been realised. A 23.4% slot antenna area size reduction has been achieved with capacitor loading compared with the ordinary slot antenna. The antenna has the advantages of a good impedance bandwidth and good linearly polarised radiation patterns after chip capacitor loading     

Compact wound-type slot antenna with wide bandwidth

A new type of a slot antenna in which a slot is formed in wound-type around a dielectric substrate is proposed. In comparison with a conventional meander slot antenna, the proposed antenna has a wider bandwidth and smaller size. The proposed antenna has been designed on a gallium arsenide (GaAs) substrate and fabricated by integrated circuit process for the integration of the antenna with active components. The fabricated antenna has dimensions of 6.2 /spl times/4.1 mm/sup 2/ and a 10-dB bandwidth of 300 MHz at 5.8 GHz.     

Performance characteristics of the dual exponentially tapered slot antenna (DETSA) for wireless communications applications

The dual exponentially tapered slot antenna (DETSA) is a low-profile slot line radiator that is a modified form of a Vivaldi radiator. The DETSA is created by taking a Vivaldi radiator and tapering the outside edge of the slot line conductors. The shape of the outside edge of the slot line conductors adds additional antenna design degrees of freedom. This paper describes how the different shape parameters of the DETSA impact antenna performance.     

X 波段加膜片式单脊波导裂缝天线的研究

等效导纳值是波导宽边纵缝天线的关键设计参数。为克服传统波导裂缝天线副瓣偏高、设计效率低下等问题,本文提出了一种单脊波导裂缝天线的改进设计方法,在传统波导裂缝阵列天线设计的基础上,利用等效导纳值对天线等效电路的影响,在裂缝单元下增加金属膜片,通过改变金属膜片的高度,优化裂缝等效导纳值,使得每个裂缝口径场分布更加接近于理论设计值,并在设计过程中使用牛顿迭代法提取导纳进一步缩短设计时间。通过设计实例表明:应用此方法设计单脊波导裂缝天线能够有效抑制副瓣电平,天线方位面副瓣电平可达到-30 dB 以下;在满足主要指标要求的前提下,设计效率显著提升。     

一种等边三角形缝隙环宽带天线的设计

提出一种带有枝节槽的等边三角形缝隙环结构宽带天线.基于多模谐振原理,将天线馈源设置在三角形缝隙环中非对称位置,同时在三角形缝隙环上对称添加2个枝节槽以便形成更多谐振回路,从而激励出多个模式,得到多模谐振,提高缝隙天线带宽.仿真和实测结果基本一致.实测所设计的天线的阻抗带宽为2.11～3.32 GHz,|S11|<-10...     

Development of a Cavity-Backed Broadband Circularly Polarized Slot/Strip Loop Antenna With a Simple Feeding Structure

A cavity-backed loop antenna is developed for producing broadband circularly polarized (CP) radiation. The antenna configuration consists of a slot loop and a strip loop. The slot loop radiates a CP wave at a lower frequency while the strip loop produces CP radiation at a higher frequency. A combination of the two frequencies leads to a bandwidth enhancement. The slot/strip loop antenna is fed by a single straight microstrip line. It is demonstrated that the cavity-backed slot/strip loop antenna can achieve an axial ratio (les 3 dB) bandwidth of 19% with good impedance matching. The antenna configuration is described and the operating principles for broadband circular polarization and impedance matching are analyzed. The antenna performance is confirmed by experimental results.     

Stainless steel slot antenna with integrated solar cells

A new principle of a solar slot antenna is presented. The slot antenna integrates amorphous silicon solar cells which are directly grown on the ground plane where the slot antenna is cut. To facilitate the deposition of the solar cells, stainless steel was used for the ground plane. The effect on the efficiency of the antenna of this rather unusual choice for the conducting ground plane is also described     

一种新型 SIW 背腔缝隙天线的研究

介绍了一种新型基片集成波导背腔六边形缝隙线极化天线。背腔缝隙天线是一种技术成熟的天线类型,但是笨重的体积限制了传统金属腔体缝隙天线的发展。基于基片集成波导结构的背腔缝隙天线以其低损耗、高功率容量、高增益 以及易集成等诸多优点而备受关注。文中设计了一款基于基片集成波导加开六边形缝隙的背腔天线,通过CST软件仿真,并制作了天线实物进行测试。天线的中心工作频率为10 GHz,增益为4. 87 dB,带宽为147 MHz。     

RCS reduction and gain enhancement of SRR inspired circularly polarized slot antenna using metasurface

In this work, a novel Circularly Polarized (CP) slot antenna is proposed for low RCS and high gain applications. The proposed antenna is designed in two phases. Initially, a metasurface is designed, which is composed of two similar artificial magnetic conductor (AMC) unit cells arranged orthogonally in chessboard-like configuration for broadband RCS reduction. Then, the CP slot antenna is designed by placing dual SRR on the backside of the slot for impedance matching and to achieve circular polarization. Detailed analysis is conducted to investigate the performance of metasurface loaded CP slot antenna. The proposed antenna shows 10 dB RCS reduction over the bandwidth of 41.3% at boresight direction compared to CP slot antenna. The maximum in-band and out-of-band RCS reduction achieved is 24 dB and 20 dB, respectively. The maximum gain of the antenna is also increased by 2.7 dB as a result of parasitic radiation of the metasurface and an improvement in overall performance of the antenna is observed by the employment of metasurface. Measured results of the fabricated prototype are in good agreement with the simulated results.     

一种新型CPW 馈电宽带圆极化缝隙天线

设计了一种新型的CPW 馈电宽带圆极化缝隙天线,圆形槽天线与共面波导馈电在介质板的同面上。通过在 两个圆形槽的中间开一个纵向插槽,调整槽之间的相对位置和各自的几何参数,可以得到一个由两个正交九十度相位 差的电场激发的圆极化波。最终仿真结果表明该天线在频带1.0GHz 到1.8GHz 满足反射系数小于-10dB、轴比小于3dB, 相对带宽达到57%,工作频带覆盖了GPS 等卫星导航系统。该天线具有十分紧凑的平面结构,结构简单,容易加工, 便于实验调试,具有广阔的应用前景。     

一种共面波导馈电的缝隙型超宽带天线

针对超宽带通信系统,提出一种小型超宽带天线,可以应用于终端设备。天线类型为共面波导馈电的缝隙型,缝隙结构为一矩形与一圆形组合而成,馈电结构与缝隙结构相似。天线的面积为22 mm×27 mm,印刷在厚度为0. 5 mm的FR4衬底上. 通过软件仿真分析了天线的工作原理以及尺寸对带宽的影响,仿真结果显示天线的带宽在不同的衬底厚度下均能覆盖UWB频段。天线的测试带宽为2.4 GHz~14.4 GHz,在超宽带的工作频段内测试效率超过76% ,测试增益大于2.1 dBi。     

一种展宽波导缝隙阵列天线驻波带宽的新方法

辐射缝隙导纳和耦合缝隙阻抗的频率特性,是影响缝隙阵列天线驻波带宽的主要因素。以改善整个缝隙阵阻抗匹配频率特性为出发点,提出了一种展宽波导缝隙阵列天线驻波带宽的新方法,即选择合适的辐射缝隙的总导纳常数。仿真分析表明,改变后的缝隙阵列天线的驻波带宽有了较大改善,其与理论分析的结果是一致的。