Scalable multi-QoS IP+ATM switch router architecture

This article proposes a scalable multi-QoS IP+ATM switch router architecture. The proposed switch router is based on a core ATM switching system with multi-QoS capability. Forwarding engines and a routing engine are attached in front of the line cards of the ATM switching system. The FEs and RE are interconnected with each other via internal VCs. A novel longest matching algorithm is employed at the FE to achieve packet forwarding at wire-speed of OC-12c rate (622.08 Mb/s). Wire-speed unicast and multicast packet forwarding are performed using point-to-point and point-to-multipoint VCs in a unified way. Because FEs and RE are decoupled from the base ATM switching system, the full spectrum of ATM QoS capability is nicely applied for IP QoS control with a packet classification at the edge of the network. The core switching fabric is scalable from 40 to 160 Gb/s capacity (371 MPPS in terms of packet forwarding throughput). Feedback rate control is employed at each line card to eliminate congestion in the high-speed core switching fabric even with a small amount of buffer.     

宽带综合IP网的MPLS技术及其应用

多协议标记交换（MPLS）技术是综合利用网络第二层交换技术的有效性和第三层IP路由的灵活性等优点而产生的多层交换技术。通过在传统的IP包里加入标记，使路由转发依赖于标记，大大地提高IP包的转发速度，同时可使传统IP网络具有服务质量（QoS）能力。现主要分析MPLS体系结构，指出MPLS的一些应用。     

Quality-of-service mechanisms in IP-over-WDM networks

Classical approaches to QoS provisioning in IP networks are difficult to apply in all-optical networks. This is mainly because there is no optical counterpart to the store-and-forward model that mandates the use of buffers for queuing packets during contention for bandwidth in electronic packet switches. Since plain IP assumes a best effort service model, there is a need to devise mechanisms for QoS provisioning in IP over wavelength-division multiplexing networks. Such mechanisms must consider the physical characteristics and limitations of the optical domain. This article presents a classification and survey of proposals for QoS provisioning and enforcement in IP-over-WDM networks. The different QoS proposals surveyed cover three major optical switching methods: wavelength routing, optical packet switching, and optical burst switching.     

Architecture, design, and modeling of the OPSnet asynchronous optical packet switching node

An all-optical packet-switched network supporting multiple services represents a long-term goal for network operators and service providers alike. The EPSRC-funded OPSnet project partnership addresses this issue from device through to network architecture perspectives with the key objective of the design, development, and demonstration of a fully operational asynchronous optical packet switch (OPS) suitable for 100 Gb/s dense-wavelength-division multiplexing (DWDM) operation. The OPS is built around a novel buffer and control architecture that has been shown to be highly flexible and to offer the promise of fair and consistent packet delivery at high load conditions with full support for quality of service (QoS) based on differentiated services over generalized multiprotocol label switching.     

光突发交换网络中的突发分组组装策略

光突发交换(OBS)技术集成光电路交换和光分组交换的优势,能满足现有大容量、高速率的多媒体信息交换与传输,将成为下一代光IP骨干网的核心技术。本文详细论述了OBS网络中的关键技术———突发分组的组装技术的各种策略与实现方式,指出具有良好QoS保证又可降低可操控性的突发组装策略将成为最佳选择。     

ITU-T QoS standards for IP-based networks

To support IP/PSTN convergence, future IP networks will need to provide reliable differentiated QoS to a diverse set of user applications, including telephony. To achieve end-to-end QoS solutions, IP network providers will need to agree on a common set of IP packet transfer performance parameters and QoS objectives. This article describes two new ITU-T Recommendations, Y.1540 and Y.1541, that document such an agreement.     

A novel IP with MPLS over WDM-based broad-band wavelength switchedIP network

This paper presents a new technology for constructing IP over photonic systems. An IP with multiprotocol label switching (MPLS) over wavelength division multiplexing (WDM)-based broad-band IP network architecture and protocol is proposed and analyzed in this paper, which supports variable-length IP-like optical packet label switching and optical virtual path routing. This system tries to merge into one layer the functionalities of the wavelength switching, SONET mux/demux, and IP routing, and is sometimes known as the concept of optical MPLS. The label banding, forwarding/switching process, and node architecture of the proposed network are discussed and studied. A unique as well as important function of a lambda/label edge router (LER) is a flow assembly device that can encompass MPLS' forward equivalence classes, label stacking, and label switching path aggregation function. At the same time, a particular function of the core label switching router is wavelength merging. A fiber delay line is used to delay the data stream in order to process the label information and resolve contention. Transmission bit error rate measurements of the baseband data stream and back-to-back is also demonstrated to show its feasibility     

High-Performance Hybrid-Switching Optical Router for IP over WDM Integration

Because pure electrical routers with their bandwidth limitations can hardly keep up with the tremendous traffic growth in the Internet, optical routers based on various optical switching techniques including optical wavelength switching (OWS), optical burst switching (OBS), and optical packet switching (OPS) have been suggested to cope with this problem. However, because OBS and OPS are both in their early experimental phase and OWS only provides coarse granularity switching, a hybrid-switching optical router with combined OWS and electrical packet switching is a necessity in order to accommodate the entire multi-granularity traffic with multi-service requirements in a cost-effective manner. Its coordination capability of optical circuit switching and electrical packet switching enables efficient/intelligent usage of network resources. In this paper, we first review research and developments of such IP routers employing optical switching/interconnection techniques and examine how these techniques can be used inside routers to scale node capacity and to improve optical Internet performance. We also present and study the performance of a terabit optical router with an optical-electrical hybrid-switching fabric. The node architecture is based on the idea of IP over WDM integration with Generalized Multi-Protocol Label Switching (GMPLS). The network-level performance evaluations show that the proposed hybrid-switching optical router is a cost-effective solution for building the next generation GMPLS-based multi-granularity optical Internet.     

End-to-End Adaptive QoS Provisioning over GPRS Wireless Mobile Network

The General Packet Radio Service (GPRS) offers performance guaranteed packet data services to mobile users over wireless frequency-division duplex links with time division multiple access, and core packet data networks. This paper presents a dynamic adaptive guaranteed Quality-of-Service (QoS) provisioning scheme over GPRS wireless mobile links by proposing a guaranteed QoS media access control (GQ-MAC) protocol and an accompanying adaptive prioritized-handoff call admission control (AP-CAC) protocol to maintain GPRS QoS guarantees under the effect of mobile handoffs. The GQ-MAC protocol supports bounded channel access delay for delay-sensitive traffic, bounded packet loss probability for loss-sensitive traffic, and dynamic adaptive resource allocation for bursty traffic with peak bandwidth allocation adapted to the current queue length. The AP-CAC protocol provides dynamic adaptive prioritized admission by differentiating handoff requests with higher admission priorities over new calls via a dynamic multiple guard channels scheme, which dynamically adapts the capacity reserved for dealing with handoff requests based on the current traffic conditions in the neighboring radio cells. Integrated services (IntServ) QoS provisioning over the IP/ATM-based GPRS core network is realized over a multi-protocol label switching (MPLS) architecture, and mobility is supported over the core network via a novel mobile label-switching tree (MLST) architecture. End-to-end QoS provisioning over the GPRS wireless mobile network is realized by mapping between the IntServ and GPRS QoS requirements, and by extending the AP-CAC protocol from the wireless medium to the core network to provide a unified end-to-end admission control with dynamic adaptive admission priorities.     

LOBS网络的QoS分析

网络的服务质量(QoS)是下一代IP over WDM光因特网中一个很重要的问题。光标签突发包交换技术(LOBS)作为一种新出现的光交换技术,必须支持QoS。文章主要介绍了LOBS网络的特点,并回顾和总结了已有的光突发交换(OBS)网络QoS方案,讨论了在LOBS中的QoS准则。     

Optical burst switching: a viable solution for terabit IP backbone

Wavelength-division multiplexing has emerged as an important physical layer technology. Optical transmission provides a physical layer capable of carrying bits at the speed at the order of a gigabit per second. Optical burst switching is proposed to overcome the shortcomings of conventional WDM deployment, such as lack of fine bandwidth granularity in wavelength routing and electronic speed bottlenecks in SONET/SDH. We describe an architecture for IP network over the OBS WDM transmission core. The use of MPLS-type technique for forwarding data bursts and the inclusion of a medium access control layer between the optical (WDM) and IP layers are the key ingredients of the proposed architecture. In particular, the architecture is based on provisioning MPLS paths, also called label switched paths, of desired quality of service through the OBS WDM transmission core. The MAC layer performs various OBS-specific functions, such as burst assembly, burst scheduling, and offset setting/traffic shaping. While burst assembly and burst scheduling are relatively straightforward, we point out that the offset setting strategy has significant impact on the performance of IP network operating over OBS WDM core. We describe a shaping scheme to set the offset, an important system parameter for OBS, between the successive data bursts of a given data stream (label switched path) and their associated control packets. This scheme results in robust operation of the network and also facilitates traffic engineering. Guidelines are provided for implementing various IP QoS mechanisms in the optical backbone using OBS.     

Topics in Optical Communications - Operational Evaluation of ASON/GMPLS Interdomain Capability over a JGN II Network Testbed

Traffic engineering in backbone networks is an important issue in supporting an appropriate QoS level to accommodate various types of traffic flows efficiently. Automatically switched optical networks and generalized multiprotocol label switching control planes are promising functionalities to achieve the sophisticated mechanism of interdomain traffic engineering. In this article we address dynamic operational scenarios to control IP traffic flows using the ASON/GMPLS control plane. This includes cut-through IP/MPLS routers and the rerouting of failed links through the tunnel of optical label-switched paths. This article presents an operational evaluation of traffic engineering. More specifically, we present QoS recovery for protecting high priority traffic using policy controllers and fault recovery of inter-domain LSPs over the JGN II network testbed. This article evaluates and discusses the feasibility of these operational scenarios using state-of-the-art optical switching and control- plane technologies.     

Critical issues of onboard switching in DVB-S/RCS broadband satellite networks

The next generation of broadband satellite networks is challenged to accommodate multimedia services while concurrently integrating with terrestrial IP networks. With IP applications dominating the Internet, carrying IP traffic over the satellite has been under intensive study. Originally developed to bring digital television home through satellites, the DVB-S and DVB-RCS standards empower interactive satellite communications with economical standardized satellite terminals. Furthermore, onboard switching technology is increasingly gaining attention, due to optimized bandwidth usage, fully meshed network topology through one satellite hop, and quality of service guarantee. This article investigates the onboard switching technologies in DVB-S/DVB-RCS broadband satellite networks. Aside from the network system infrastructure and switch hardware architecture, the QoS mechanisms supported by the switch onboard the satellite are discussed in depth.     

Demonstration of the highly reliable Hikari router network based on a newly developed disjoint path selection scheme

Integration of multiprotocol label switching functions and multiprotocol lambda switching functions can enhance the throughput of IP networks and remove bottlenecks that are derived from electrical packet processing. To enhance the packet forwarding capability, NTT proposed a photonic MPLS concept that includes MP/spl lambda/S, and demonstrated IP, MPLS, and photonic MPLS integrated router systems called the photonic MPLS router. This router system is now called the Hikari router. The word Hikari is Japanese meaning beam, light, lightwave, optical, photonic, and sunshine. The amount of IP data traffic has grown remarkably. Massive IP routers and flexible route control mechanisms are now required to cope with the increased amount of traffic. The Hikari router can offer two solutions utilizing photonic switching technologies, and photonic network operation and management technologies. The first solution is utilizing photonic switching technologies realized using optical-switch-based crossconnect systems. The other solution is realized using the MPLS and MP/spl lambda/S signaling protocol and photonic network protection functions. In this article we report on the implementation of the Hikari router systems, propose a newly developed disjoint path selection scheme for generalized MPLS networks with shared risk link group constraints, and demonstrate the signaling protocol and network protection functions. The demonstration system achieves a distributed optical path set-up/tear-down protocol with an extended constraint-based routing label distribution protocol. Fast self-healing through automatic protection switching and a new restoration scheme are also implemented. These functions are successfully implemented, and the performance is verified on a demonstration network. The protection switching scheme achieves protection in less than 20 ms, and the optical path restoration scheme achieves restoration in less than 500 ms.     

UMB网络架构

超移动觅带（UMB）无线接入技术能以非常高的速率实现IP分组的有效无线传送,同时,即使在小区边缘,也可提供无缝移动和最佳的服务质量（QoS）,而不会降低频率再用。UMB系统利用高度创新的扁平化网络架构,简化了核心网和网络接口,从而易于实现网络扩展。UMB架构的一个主要原则是无缝移动。网络架构的设计是关键所在,有利于实现在UMB网络内和不同技术间的无缝切换。革新性的概念可实现基站间的快速交换,同时最大限度地减少开销和提供简化的网络接口。新的隧道机制提供在数据一链路层（层2）和IP层（层3）的信令交换,实现了跨基站的快速移动。本文探讨了UMB网络架构的主要特性,并对不同架构设计选择进行了深入分析。     

An optical packet contention resolution supporting QoS differentiation with LRWC wavelength converters for OPS

The wavelength conversion is regarded as an effective way to resolve the optical packet contention in the wavelength domain for optical packet switching. An optical packet switching node, based on shared-per-node equipped with limited range wavelength converters and parametric wavelength converters (SPN-LP), is designed to further reduce optical packet loss probability. A novel optical packet contention resolution with priority differentiation wavelength scheduling algorithm to support quality of service (QoS) for the SPN-LP architecture is put forward in the article. The simulation results show that proposed optical packet resolution enables a good QoS differentiation, namely the high priority contending optical packet has the sufficient low packet loss probability.     

Demonstration of 10 Gbit Ethernet/Optical-Packet Converter for IP Over Optical Packet Switching Network

We developed novel network interfaces, for example 10 Gbit Ethernet to 80 Gbit/s optical-packet (10 GbitE–80 GbitOP) or 80 Gbit/s optical-packet to 10 Gbit Ethernet (80 GbitOP–10 GbitE) converters (collectively called as 10 GbitE/80 GbitOP converters), to connect optical packet switching (OPS) networks with IP technology-based networks. By using newly developed arrayed burst-mode optical packet transmitters/receivers together, the 10 GbitE–80 GbitOP converter at the ingress edge node of the OPS network encapsulates an IP packet into an $80(8lambdatimes 10) {rm Gbit/s}$ dense wavelength division multiplexing (DWDM)-based optical packets and generates an optical label based on a lookup table and the destination addresses of the IP packet. The 80 GbitOP–10 GbitE converter at the egress edge node decapsulates the IP packet from the optical packet and generates a 10 GbitE frame accommodating the IP packet according to a lookup table. By using these network interface devices and OPS system based on multiple optical label processing, we achieved, for the first time, 74-km single-mode fiber transmission, switching, and buffering of $80(8lambdatimes 10) {rm Gbit/s}$ DWDM-based optical packets encapsulating almost 10 Gbit/s IP packets with error-free operation (IP packet loss rate $≪ 10^{-6}$).      

A Study on a Differentiated Service Queuing Scheme Based on Transmitted Bytes Within a UMTS Core Network Gateway

Universal mobile telecommunications system (UMTS) is a popular 3G system to support network applications full of variety. According to the quality of service (QoS) features of four types of UMTS traffic, this study proposes a BBQ (byte-based queuing) scheme to handle a UMTS packet forwarding process in differentiation. With the BBQ scheme, four types of UMTS traffic depend on their QoS features to receive differentiated packet forwarding performance within a UMTS core network. Several scenarios are simulated to realize the packet transmission performance of the BBQ scheme. Moreover, a packet transmission performance comparison between the IETF RIO scheme and the BBQ scheme is discussed in this study. The simulation results show that a differentiated packet forwarding behavior among UMTS traffic can be provided by the BBQ scheme with low cost operation/architecture; this demonstrate the effectiveness of the proposed queuing scheme.     

QoS Provisioning in Wireless IP Networks

This paper deals with quality of service (QoS) provision in wireless IP networks. QoS provision is particularly challenging in wireless networks, where network resources are generally limited, variable over time and shared. In the design of possible measures to assure QoS one should consider that standardization is well established for the network layer Internet Protocol and for many underlying technologies of frequent use (e.g. IEEE 802.11, BLUETOOTH or HIPERLAN II). Therefore, as far as research on QoS is concerned, there is little room in both the IP and the link-layers for improved IP over wireless interfaces. In this paper we illustrate a solution in which an intermediate Wireless Adaptation Layer (WAL) is transparently interposed between the IP layer and specific link-layer technologies as a solution to provide QoS. The WAL addresses two main issues: (i) compensation for channel impairments in different platforms in order to enhance wireless channel reliability and (ii) implementation of traffic control and packet scheduling mechanisms to satisfy bandwidth and delay requirements, as well as to enforce a general principle of fairness among the IP associations contending for network resources and achieve optimal exploitation of transmission capacity. The WAL consists of a set of modules, each one in charge of a specific task, which can be enabled or disabled depending on the specific network environment. The novelty of the WAL approach is its capability of adapting itself to different wireless interfaces selecting performance enhancing modules for specific networks. This requires to modify the standard TCP/IP protocol stack by introducing an intermediate layer between the IP layer and the Data Link layer, with performance enhancement purposes. This paper focuses on two modules in particular, namely a traffic control module, which is in charge of performing congestion control and channel state dependent scheduling (CSD) packet scheduling, and a forward error correction (FEC) module, which compensates for channel impairments. This paper presents the proposed architecture provided with these modules and reports some measurements and simulations highlighting benefits resulting from the use of such modules.     

Demonstration of 100 Gbps optical packet switching using header processor based on 48-bit longest prefix matching

Wire-rate packet processing and its energy saving for over 100 Gbps speed of line are major issues to be resolved in optical packet switching (OPS) networks. For that purpose, we newly develop a high-speed, deterministic-latency electronic header processor based on longest prefix matching (LPM) for searching optical packet destination addresses (OP-DAs). This paper reports the successful experimental results of electronic header processing based on LPM search of up to 48 bits and optical switching of 100 Gbps optical packets by the use of the header processor. We demonstrate 48-bit LPM-capable optical packet switching. We also demonstrate IP packet transfer and 32-bit LPM-capable optical packet switching. In the latter demonstration, the 32-bit OP-DA of optical packets is directly copied from the 32-bit destination address of Internet Protocol version 4 (IPv4) packets. This result indicates that OPS networks can be deployed with electronic IP networks by the use of integrated network operation between OPS and IP networks.