Corrosion behaviour of corrugated lean duplex stainless steels in simulated concrete pore solutions

This work studies the corrosion behaviour of two corrugated lean duplex stainless steels (SAF 2001 and 2304 grades) in eight alkaline solutions (carbonated and non-carbonated, saturated Ca(OH)₂ solutions with different chloride contents). 2001 stainless steel is a new grade in market because of its composition. 2304 is a grade previously studied under different conditions. However, its use as reinforcement in concrete is new. Studies are carried out by polarization curves following scanning electronic microscopy (SEM) and optical observations. Results are compared to those of carbon steel and austenitic AISI 304 and duplex SAF 2205 under similar conditions. After corrosion tests in alkaline media with chloride, ferrite tends to corrode selectively in 2304 duplex, while austenite corrodes selectively in 2001 under the same conditions. The influence of the duplex microstructure on attack development and morphology is analyzed. The electrochemical parameters obtained from the polarization curves suggest 2001 could replace 304 keeping the structure its corrosion performance (and with clear economical advantages). 2304 shows better corrosion behaviour than the more expensive 304, but somewhat lower than the excellent behaviour shown by 2205.     

Effect of ageing heat treatments on the microstructure and intergranular corrosion of powder metallurgy duplex stainless steels

The influence of ageing heat treatments (675 and 875 °C for 1.5 to 48 h) on the microstructure and intergranular corrosion resistance of sintered in nitrogen duplex stainless steels was investigated. The materials were obtained by sintering mixtures of austenitic AISI 316L and ferritic AISI 430L powders. Corrosion behaviour was evaluated by using electrochemical techniques. The beneficial effect of nitrogen on corrosion behaviour of solution annealed samples was established. During ageing, secondary phases were precipitated and the intergranular and transgranular corrosion resistance significantly decreased though repassivation was observed in specimens aged at 875 °C for times up to 8 h.     

Electrochemical reactivation methods applied to PM austenitic stainless steels sintered in nitrogen-hydrogen atmosphere

Exposure methods (ASTM A262 Practice A and Modified Strauss Test) and electrochemical reactivation methods such as EPR and EPRDL was applied to PM 304L and PM 316L stainless and comparisons with wrought stainless steels were made. Sintering in vacuum and nitrogen-hydrogen atmosphere was chosen. The latter was the focus of the work and the former was used on comparative basis. It was seen how nitrogen in PM stainless steels plays a relevant role both when is dissolved and when is in intermetallic precipitates. A set of heat treatments were applied: annealing and sensitizing at 375, 675 and 875 °C. The results indicate that the electrochemical reactivation methods are suitable to evaluate the degree of sensitization of PM austenitic stainless steels.     

Pitting corrosion behaviour of PM austenitic stainless steels sintered in nitrogen-hydrogen atmosphere

PM 304L and 316L stainless steel have been compacted at 400, 600 and 800 MPa and sintered in vacuum and in nitrogen-hydrogen atmosphere. Postsintered heat treatments (annealing solution and ageing at 375, 675 and 875 °C) have been applied. Pitting corrosion resistance has been studied using anodic polarization measurements and the ferric chloride test. Anodic polarization curves reveal that densities and atmospheres are relevant on anodic behaviour. Pitting resistance is higher for PM 316L and for higher densities and vacuum as sintered atmosphere. Ageing heat treatments at medium and high temperatures are detrimental to passivity although susceptibility to pitting corrosion barely changes. But heat treatments at 375 °C even show certain improvement in pitting corrosion resistance. The results were correlated to the presence of precipitates and mainly to the lamellar constituent which appears in some samples sintered in nitrogen-hydrogen atmosphere. The role of nitrogen on the samples sintered under nitrogen-hydrogen atmosphere and its relation to the microstructural features was described.     

Pitting corrosion behaviour of austenitic stainless steels - combining effects of Mn and Mo additions

Mn and Mo were introduced in AISI 304 and 316 stainless steel composition to modify their pitting corrosion resistance in chloride-containing media. Corrosion behaviour was investigated using gravimetric tests in 6 wt.% FeCl₃, as well as potentiodynamic and potentiostatic polarization measurements in 3.5 wt.% NaCl. Additionally, the mechanism of the corrosion attack developed on the material surface was analysed by scanning electron microscopy (SEM), X-ray mapping and energy dispersive X-ray (EDX) analysis. The beneficial effect of Mo additions was assigned to Mo⁶⁺ presence within the passive film, rendering it more stable against breakdown caused by attack of aggressive Cl⁻ ions, and to the formation of Mo insoluble compounds in the aggressive pit environment facilitating the pit repassivation. Conversely, Mn additions exerted an opposite effect, mainly due to the presence of MnS inclusions which acted as pitting initiators.     

Comparative study of stress corrosion cracking susceptibility of Fe18Cr10Mn- and Fe18Cr10Mn1Ni-based high nitrogen stainless steels

The stress corrosion cracking (SCC) behavior of Fe18Cr10Mn1Ni(0.3–0.8)N alloys was investigated in aqueous NaCl environment by using slow strain rate test method, and the results were compared to those of Ni-free counterparts. The addition of N tended to improve the SCC resistance of Fe18Cr10Mn- and Fe18Cr10Mn1Ni-based alloys. The alloying Ni magnified the beneficial effect of N on the SCC susceptibility and, eventually, the Fe18Cr10Mn0.8N alloy was immune to SCC in 2 M NaCl solution at 50 °C. The SCC behavior of the present alloys was found to be closely related to the repassivation tendency and the resistance to pitting corrosion.     

Electrochemical behaviour of duplex stainless steels in caustic environment

Recent studies have shown that duplex stainless steels can be susceptible to general corrosion and stress corrosion cracking in high pH caustic environments. This difference in the corrosion resistance can be attributed to changes in the electrochemical behaviour of steels. The present study has shown that the corrosion rates of duplex stainless steels increase with an increase in temperature and sulphide addition to caustic environments. Moreover, alloying Fe with Cr and Ni helps to raise the corrosion potential and lower critical current density of DSS in an alkaline environment whereas Mo can be detrimental to the corrosion resistance of the steel.     

Electrochemical behavior of sintered oxide dispersion strengthened stainless steels

The electrochemical behavior of powder metallurgy (P/M) oxide dispersion strengthened stainless steels (SS) (316L and 434L) have been compared with standard 430 and 316 wrought samples in 0.05 mol/l sulfuric acid. The effects of sintering temperature and yttria addition on the electrochemical behavior have been studied. The behaviour of the dispersion strengthened SS was comparable to that of the straight P/M samples. The straight P/M samples sintered at 1400 °C exhibited better corrosion resistance compared to the samples sintered at 1250 °C and this has been correlated to sintered densities. The P/M austenitic SS were superior to the P/M ferritic SS. Pitting resistance, studied by cyclic polarization experiments in 3.56 wt.% NaCl, of the P/M samples were comparable to the wrought samples. The addition of Y₂O₃ did not affect the pitting resistance.     

Aqueous corrosion behaviour of sintered stainless steels manufactured from mixes of gas atomized and water atomized powders

The electrochemical corrosion improvement of a powder metallurgical (PM) stainless steel is studied in this work. Water atomized (WA) ferritic AISI 434L powders have been mixed with gas atomized (GA) austenitic (AISI 316L type) and ferritic (AISI 430L type) powders and processed through the traditional PM route. The addition of GA powder to the usual WA powder decreases the mean size of the pores of the sintered stainless steels. As the bigger pores are the ones that are able to act as crevices, unlike the smaller ones - that act as closed porosity, reduction in the number of big pores tends to improve the corrosion behaviour of PM stainless steels. Reductions of the corrosion rate (i_corr) and increases of the corrosion potential (E_corr) have been measured in neutral media, with and without chlorides. Moreover, the additional beneficial effect of achieving a duplex microstructure through the addition of GA austenitic powders to the WA ferritic powders has also been verified.     

The effect of large heat input on the microstructure and corrosion behaviour of simulated heat affected zone in 2205 duplex stainless steel

In the simulated heat affected zone of 2205 duplex stainless steels, effects of large welding heat inputs on the microstructure and corrosion behaviour were investigated. Reformed austenite content increased with the coarsening of grain boundary austenite (GBA) and the growth of intragranular austenite (IGA) and Widmanstatten austenite (WA), thus improving the low temperature toughness and affecting corrosion state. Reduction of chromium nitrides contributed to better resistance to pitting corrosion. Moreover, the pitting corrosion and intergranular corrosion were improved resulting from the formation of more GBA and WA. The specimen with a Δt_8/5 of 100 s presents better comprehensive performance.     

Potentiodynamic polarization behaviour of AISI type 316 stainless steel in NaCl solution

Potentiodynamic polarization behaviour of AISI type 316 SS in NaCl solution was investigated in terms of the potential scan rate effect. The critical pitting potential, E_pit, of the stainless steel appeared to be strongly dependent on the potential scan rate. A cumulative anodic electric charge density of the steel was defined as the total charge density from the open circuit potential, E_ocp, and calculated using the potentiodynamic polarization curves. It was found that, plotted as a function of the polarization time, the values of the cumulative charge density consisted of two lines with different slopes. It was confirmed that the deflection of the cumulative charge density vs. time plots corresponded to E_pit and the values of the cumulative charge density at the deflection were little dependent on the applied scan rate. The cumulative charge density at the deflection was defined as a critical electric charge density for the stable pitting. Also, it was suggested that this electric charge density should be associated with the critical condition for the stable pitting and the critical electric charge for stable pitting should be a representative parameter for the pitting resistance of a material.     

Effect of N and C on stress corrosion cracking susceptibility of austenitic Fe18Cr10Mn-based stainless steels

Stress corrosion cracking (SCC) susceptibility of austenitic Fe18Cr10Mn alloys with 0.3N, 0.6N and 0.3N0.3C was investigated in aqueous chloride environment using a slow strain rate test method. The SCC susceptibility of Fe18Cr10Mn alloys in 2 M NaCl solution at 50 °C under constant anodic potential condition decreased with increase in N content from 0.3 to 0.6 wt%, and with addition of 0.3 wt% C to the Fe18Cr10Mn0.3N alloys. The present study strongly suggested that the beneficial effects of N and C on the SCC behavior of Fe18Cr10Mn alloys would be associated with the resistance to pitting corrosion initiation and the repassivation kinetics.     

Effect of laser surface melting on intergranular corrosion behaviour of aged austenitic and duplex stainless steels

In the present study, the effect of laser surface melting (LSM) on intergranular corrosion behaviour of aged austenitic stainless steels (UNS S30400, S31603, S32100 and S34700) and aged duplex stainless steels (UNS S31803 and S32950) were investigated. LSM of the aged stainless steels was carried out using a 2.5 kW CW Nd:YAG laser. The microstructure of the aged stainless steels after LSM depends on their compositions. After LSM, the aged austenitic stainless steels mainly contain austenite (γ) with some ferrite (δ) as the minor phase, but the carbide phases are completely eliminated. For the aged duplex stainless steels after LSM, δ becomes the major phase and the δ/γ phase balance is disturbed, whereas the sigma (σ) phase is eliminated. The degree of sensitization (DOS) and corrosion morphology of the aged stainless steels before and after LSM were determined by the double loop electrochemical potentiokinetic reactivation (DL-EPR) using a potentiostat and SEM observation, respectively. Desensitization of the aged stainless steels has been successfully achieved by LSM and their intergranular corrosion resistance is found to be significantly enhanced as reflected by the decrease in DOS due to dissolution of the carbides or σ phase, which reduced Cr depletion or the possibility of solute segregation at the grain or phase boundaries, despite the presence of δ and disturbance of δ/γ phase balance.     

Pitting corrosion behaviour of austenitic stainless steels with Cu and Sn additions

The influence of Cu and Sn on the pitting corrosion resistance of AISI 304 and 316 stainless steels in chloride-containing media has been investigated. The corrosion behaviour was evaluated by cyclic polarization, potentiostatic CPT measurements and electrochemical impedance spectroscopy in 3.5 wt% NaCl. The corrosion resistance was also studied in FeCl₃ under Standard ASTM G-48. According to the results, Cu addition favours pit nucleation but inhibits its growth, whereas Sn exerts the opposite effect, favouring pit growth and inhibiting its nucleation. Studies by SEM, X-ray mapping and EDS analysis showed Cu-, Cl- and O-rich corrosion products that reduce the extent of corrosion damage.     

Electrochemical behaviour enhancement of stainless steels by a SiO2 PACVD coating

Amorphous silica coatings have been deposited by plasma assisted chemical vapor deposition (PACVD) process on M2 steel and 304 stainless steel substrates. The chemical inertia of the coating has been established by resonant quartz crystal microbalance (RQCM), and no porosity has been observed at the AFM scale. The barrier effect has been evaluated on M2 steel by applying the concept of dipolar relaxation. The protection is very efficient, and no deleterious galvanic coupling with the uncoated metallic surface can occur.

A coated stainless steel was also investigated in NaCl solution in order to understand how the passive properties are influenced by such a barrier coating. When deposited on stainless steel, coated part keeps the beneficial passive behaviour inherent to the substrate. They evidence almost no corrosion. The silica based layer behaves as a quasi perfect dielectric. The corrosion rate is then greatly reduced, and the pitting resistance is improved. The excellent localized corrosion protection has been explained by a tiny porosity rate, and a limited access of chloride ions through open pores.     

Corrosion behaviour of intermetallic aluminide coatings on nitrogen-containing austenitic stainless steels

The present work reports the effect of aluminide layers on the aqueous corrosion behaviour of four different 316L stainless steels containing various nitrogen contents (0.015%, 0.1%, 0.2% and 0.56% N). Diffusion annealed aluminide layers are generated over the surface by heat treatment of the aluminium precoated alloys at 750 °C for 25 h in nitrogen atmosphere. X-ray diffraction patterns of the surface modified samples showed the presence of AlN, Al₁₃Fe₄ and FeAl₂ phases. Diffusion of aluminum into the alloy, and the formation of AlN by the reaction of aluminium with matrix nitrogen, was identified using secondary ion mass spectrometry (SIMS). The nitrogen peak in the diffused layer was found to increase with increasing nitrogen content of the base alloy. SEM observation of cross-sectionally mounted alloys showed the presence of spherical AlN phase in addition to iron aluminide intermetallic phases. The role of such a composite surface layer containing intermetallic aluminides and nitride on the corrosion resistance of austenitic stainless steels in 0.5 M NaCl and 0.5 M sulphuric acid is discussed in greater detail based on open circuit potential (OCP)–time measurements, potentiodynamic polarisation studies and electrochemical impedance spectroscopy (EIS) investigations. The aluminide layered alloy with 0.1% N content showed better corrosion performance. The presence of nitrogen was found to have a positive effect in enhancing the hardness of the composite layer. Role of matrix nitrogen on the microstructure and microchemical distribution at the surface, and its role on corrosion resistance in acidic and chloride media are discussed in detail.     

Effects of solution heat-treatment and nitrogen in shielding gas on the resistance to pitting corrosion of hyper duplex stainless steel welds

The effects of solution heat-treatment and shielding gas on the pitting corrosion of hyper duplex stainless steel (HDSS) welds were investigated in highly concentrated chloride environments. The pitting resistance of a solution heat-treated HDSS after welding with an Ar shielding gas supplemented with N₂ was greatly increased due to the dissolution of Cr₂N in α-phase, which followed the diffusion of N atoms from the α-phase to the γ-phase and an increase of the γ-phase in the weld metal and heat affected zone. It was also attributed to a decrease of the pitting resistance equivalent number difference between the two phases.     

Intergranular corrosion of welded joints of austenitic stainless steels studied by using an electrochemical minicell

An intergranular corrosion study of welded joints of austenitic stainless steels (AISI 304 and 316L) has been addressed. A specific small-scale electrochemical cell (minicell) has been used. Four different weldment zones have been studied. The electrochemical methods applied were the electrochemical potentiokinetic reactivation test and electrochemical potentiokinetic reactivation double loop test. These techniques showed that the HAZ was the most critical zone to intergranular corrosion for both materials. The weld metal was susceptible to interdendritic corrosion and the fusion line showed a mixture of intergranular and interdendritic corrosion. The effect of pre- and post-welding heat treatments for AISI 316L was analyzed. The HAZ was again the most critical zone in every heat treatment condition. The results were correlated to the microstructural features of the materials.     

Microstructure and pitting corrosion resistance of annealed duplex stainless steel

The transition from metastable to stable pitting was studied in 0.5 M NaCl water solution for two cast duplex stainless steels under different microstructural conditions achieved by annealing in the range from 900 °C to 1200 °C. The ensuing microstructural changes in heat treated steels were defined and correlated with established pitting potentials (E_p) and sites of corrosion damage initiation. The variations in E_p have been discussed in terms of secondary phases precipitation. The critical condition for pit stability was quantified and used to select an appropriate microstructural state, resulting in the higher potential at which stable pit growth is first observed.     

Correlation between critical pitting temperature and degree of sensitisation on alloy 2205 duplex stainless steel

In this study effect of different ageing conditions on intergranular corrosion, pitting corrosion and relation between critical pitting temperature (CPT) and degree of sensitisation (DOS) was investigated by potentiostatic polarisation and double loop-EPR methods. The results showed by increasing sensitisation time, DOS increased and measured CPT value decreased. In addition the values of DOS and CPT of specimens aged at 650 °C showed almost liner relation while this correlation was diminished for the specimens aged at 800 °C. The results may be attributed to the further formation of precipitates on specimens aged at temperature of 800 °C.