Synergistic inhibition behaviour of methylbenzyl quaternary imidazoline derivative and iodide ions on mild steel in H2SO4 solutions

The inhibition behaviour of 2-undecyl-1-ethylamino-1-methylbenzyl quaternary imidazoline (2UMQI) and KI on mild steel in 1.0 M H₂SO₄ solutions was investigated at 25 °C using electrochemical methods. The results indicated that 2UMQI inhibited the corrosion of mild steel and the extent of inhibition increased with 2UMQI concentrations. The inhibition action in the presence of 2UMQI is due to physical adsorption of 2UMQI. A mixed-inhibition mechanism is proposed for the inhibitive effects of 2UMQI. Inhibition efficiency of 2UMQI was enhanced by the addition of iodide ions. In the presence of KI, the potentials of unpolarization, E_u was observed and increased with KI concentration.     

Corrosion and corrosion control of mild steel in concentrated H2SO4 solutions by a newly synthesized glycine derivative

A newly synthesized glycine derivative (GlyD1), 2-(4-(dimethylamino)benzylamino)acetic acid hydrochloride, was used to control mild steel corrosion in 4.0 M H₂SO₄ solutions at different temperatures (278–338 K). Tafel extrapolation, linear polarization resistance (LPR) and impedance methods were used to test corrosion inhibitor efficiency. An independent method of chemical analysis, namely ICP-AES (inductively coupled plasma atomic emission spectrometry) was also used to test validity of corrosion rate measured by Tafel extrapolation method. Results obtained were compared with an available glycine derivative (GlyD2) and glycine (Gly). Tafel polarization measurements revealed that the three tested inhibitors function as mixed-type compounds. The inhibition efficiency increased with increase in inhibitor concentration and decreased with temperature, suggesting the occurrence of physical adsorption. The adsorptive behaviour of the three inhibitors followed Temkin-type isotherm and the standard free energy changes of adsorption () were evaluated for the three tested inhibitors as a function of temperature. The inhibition performance of GlyD1 was much better than those of GlyD2 and Gly itself. Results obtained from the different corrosion evaluation techniques were in good agreement.     

Corrosion inhibition of mild steel in hydrochloric acid solution by some double Schiff bases

The inhibition effect of four double Schiff bases on the corrosion of mild steel in 2 M HCl has been studied by polarization, electrochemical impedance spectroscopy (EIS) and weight loss measurements. The inhibitors were adsorbed on the steel surface according to the Langmuir adsorption isotherm model. From the adsorption isotherm, some thermodynamic data for the adsorption process were calculated and discussed. Kinetic parameters activation such as E_a, ΔH∗, ΔS∗ were evaluated from the effect of temperature on corrosion and inhibition processes. Quantum chemical calculations have been performed and several quantum chemical indices were calculated and correlated with the corresponding inhibition efficiencies.     

Corrosion inhibition of mild steel by plant extract in dilute HCl medium

The inhibition effect of Zenthoxylum alatum plant extract on the corrosion of mild steel in 5% and 15% aqueous hydrochloric acid solution has been investigated by weight loss and electrochemical impedance spectroscopy (EIS). The corrosion inhibition efficiency increases on increasing plant extract concentration till 2400 ppm. The effect of temperature on the corrosion behaviour of mild steel in 5% and 15% HCl with addition of plant extract was studied in the temperature range 50-80 °C. Surface analysis (SEM, XPS and FT-IR) was also carried out to establish the corrosion inhibitive property of this plant extract in HCl solution. Plant extract is able to reduce the corrosion of steel more effectively in 5% HCl than in 15% HCl. The adsorption of this plant extract on the mild steel surface obeys the Langmuir adsorption isotherm.     

Corrosion inhibition of mild steel in hydrochloric acid solution by Schiff base furoin thiosemicarbazone

A heterocyclic Schiff base furoin thiosemicarbazone was tested for its corrosion inhibition towards mild steel in 1 M HCl solution using weight loss, Tafel polarization and electrochemical impedance spectroscopy techniques. Furoin thiosemicarbazone revealed good corrosion inhibition efficiency even at low concentrations towards mild steel in HCl medium. Comparison of corrosion inhibition efficiency of Schiff base and its parent amine and effect of temperature on inhibition efficiency were also investigated. The adsorption of furoin thiosemicarbazone on mild steel surface obeys Langmuir isotherm.     

N-Aminorhodanine as an effective corrosion inhibitor for mild steel in 0.5 M H2SO4

The corrosion inhibition effect of N-aminorhodanine (N-AR) on mild steel (MS) in 0.5 M H₂SO₄ was studied in both short and long immersion duration using potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), linear polarization resistance (LPR), chronoamperometry and hydrogen gas evolution. The surface morphology of MS was examined with scanning electron microscopy (SEM) in absence and presence inhibitor. The inhibitor adsorption process on MS surfaces obeys the Langmuir adsorption isotherm. The results show that NAR is a good inhibitor for MS in the acidic medium. The inhibition efficiency obtained from potentiodynamic polarization, EIS and LPR up to 98% is determined.     

Copper corrosion inhibition in O2-saturated H2SO4 solutions

Corrosion inhibition of copper in O₂-saturated 0.50 M H₂SO₄ solutions by four selected amino acids, namely glycine (Gly), alanine (Ala), valine (Val), or tyrosine (Tyr), was studied using Tafel polarization, linear polarization, impedance, and electrochemical frequency modulation (EFM) at 30 °C. Protection efficiencies of almost 98% and 91% were obtained with 50 mM Tyr and Gly, respectively. On the other hand, Ala and Val reached only about 75%. Corrosion rates determined by the Tafel extrapolation method were in good agreement with those obtained by EFM and an independent chemical (i.e., non-electrochemical) method. The chemical method of confirmation of the corrosion rates involved determination of the dissolved Cu²⁺, using ICP-AES (inductively coupled plasma atomic emission spectrometry) method of chemical analysis. Nyquist plots exhibited a high frequency depressed semicircle followed by a straight line portion (Warburg diffusion tail) in the low-frequency region. The impedance data were interpreted according to two suitable equivalent circuits. The kinetics of dissolved O₂ reduction and hydrogen evolution reactions on copper surface were also studied in O₂-saturated 0.50 M H₂SO₄ solutions using polarization measurements combined with the rotating disc electrode (RDE). The Koutecky-Levich plot indicated that the dissolved O₂ reduction at the copper electrode was an apparent 4-electron process.     

Corrosion of X65 steel in CO2-saturated oilfield formation water in the absence and presence of acetic acid

Electrochemical corrosion behavior of X65 steel in CO₂-saturated formation water in the absence and presence of acetic acid was studied by electrochemical measurements, scanning vibrating micro-electrode (SVME), localized electrochemical impedance spectroscope (LEIS) and surface analysis techniques. It is found that, when steel is immersed in formation water, the dissolution of Fe dominates the anodic process and the steel is in active dissolution state. Adsorption of intermediate product on the electrode surface results in generation of an inductive loop in the low frequency range of EIS plot. As corrosion proceeds, the concentration of Fe²⁺ in the solution increases. When the product of [Fe²⁺] × [] exceeds solubility product of FeCO₃, FeCO₃ will deposit on the electrode surface, and protects the steel substrate from further corrosion. The steel is in a “passive” state. When the electrode surface is completely covered with FeCO₃ film, the inductive loop in the low frequency range disappears. In the presence of acetic acid in formation water, the cathodic reaction will be enhanced due to the direct reduction of undissociated acetic acid. Addition of acetic acid degrades the protectiveness of corrosion scale, and thus, enhances corrosion of steel by decreasing the FeCO₃ supersaturation in solution.     

Tryptamine as a corrosion inhibitor of mild steel in hydrochloric acid solution

The inhibitor effect of tryptamine on the corrosion of mild steel in 0.5 M hydrochloric acid at 30 °C was investigated using linear polarization, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The inhibition efficiency increases with an increase in concentration of tryptamine. At 500 ppm tryptamine the inhibition efficiency calculated by these techniques is around 97%. Cathodic and anodic polarization curves of mild steel in the presence of different concentrations of tryptamine at 30 °C reveal that it is a mixed type inhibitor. Tryptamine follows Langmuir adsorption with adsorption free energy of −35.07 kJ mol⁻¹.     

The inhibition of CO2 corrosion of N80 mild steel in single liquid phase and liquid/particle two-phase flow by aminoethyl imidazoline derivatives

The inhibitory behaviour of 2-undecyl-1-aminoethyl imidazoline (AEI-11) and 2-undecyl-1-aminoethyl-1-hydroxyethyl quaternary imidazoline (AQI-11) on CO₂ corrosion of N80 mild steel in single liquid phase and liquid/particle two-phase flow was investigated using weight loss, linear polarization, potentiodynamic polarization, EIS methods and SEM observations. The two compounds inhibited the CO₂ corrosion of N80 steel and the extent of inhibition was dependent on the flow conditions and particulate content. In both phases, AQI-11 exhibited better inhibition ability than AEI-11 due to the polycentric adsorption sites on its structure. Theoretical calculation on the inhibition abilities of the compounds and their modes of adsorption are reported.     

Corrosion inhibition of mild steel in sodium chloride solution by some zinc complexes

The corrosion inhibitive effect of zinc acetate, zinc acetylacetonate and zinc gluconate on the mild steel immersed in 3.5% NaCl solution was evaluated by electrochemical impedance spectroscopy (EIS). The results revealed superiority of zinc gluconate whilst zinc acetate showed inferior corrosion inhibition. The surface of the samples exposed to the inhibited solutions was analyzed using XRD and SEM techniques. The pH measurement of the test solutions before and after corrosion, also before and after addition of Fe⁺² and Fe⁺³ revealed that the superior inhibition of zinc gluconate is related to formation of insoluble corrosion products on the mild steel surface.     

Experimental and theoretical studies for mild steel corrosion inhibition in 1 M HCl by two new benzothiazine derivatives

The inhibition effect of new heterocyclic compounds, namely 2-aryl-benzothiazin-3-one (P1) and 3-aryl-benzothiazin-2-one (P2) on mild steel corrosion in 1 M HCl was investigated using electrochemical measurements. The results indicated that the inhibition efficiency depends on concentration and molecular structure of the investigated compounds. It is also found that the inhibition of P1 is greater than P2. The molecular structure effect on the corrosion inhibition efficiency was investigated using DFT calculations. The structural and electronic parameters were calculated and discussed. The obtained results show that the experimental and theoretical studies agree well and confirm that P1 is the better inhibitor.     

The inhibition mechanism of imidazoline phosphate inhibitor for Q235 steel in hydrochloric acid medium

The inhibitive effect of a newly synthesized imidazoline phosphate inhibitor against Q235 steel and its adsorption behavior were investigated in 1 M HCl solution using weight-loss method, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The results showed that the inhibition efficiency increased with the increase of the inhibitor concentration. The imidazoline phosphate is a mixed-type inhibitor whose adsorption behavior onto Q235 steel can be well fitted by Langmuir isotherm equation. The quantum chemistry calculation exhibited that the imidazoline ring and heteroatoms of N, O, and P were the active sites of the inhibitors.     

An investigation of benzimidazole derivative as corrosion inhibitor for mild steel in different concentration HCl solutions

The influences of a benzimidazole derivative, namely 1,8-bis (1-chlorobenzyl-benzimidazolyl) -octane (CBO) on the corrosion behaviour of mild steel in different concentration HCl solutions were studied by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) measurements and SEM observations. The results showed that CBO acted as an excellent and a mixed-type inhibitor via strongly chemical adsorption onto mild steel surface to suppress simultaneously both anodic and cathodic processes according to the Langmuir adsorption isotherm. Inhibition efficiencies increased with increasing concentration of inhibitor and HCl. An inhibition mechanism was proposed in terms of strongly adsorption of inhibitor molecules on mild steel surface.     

EN, EIS and polarization studies to evaluate the inhibition effect of 3H-phenothiazin-3-one, 7-dimethylamin on mild steel corrosion in 1 M HCl solution

The corrosion inhibition effect of 3H-phenothiazin-3-one, 7-dimethylamin as a new inhibitor was studied using different electrochemical and weight loss methods. It was found that this compound acts as a strong inhibitor for mild steel in 1 M HCl even at very low concentration (1 ppm). Results showed that this compound acts as a mixed type inhibitor. As the inhibitor concentration increased, the charge transfer resistance of mild steel increased and double layer capacitance decreased. The results of EN measurements after trend removal were in good agreement with other methods results. It was found that this inhibitor acts through adsorption on the metal surface. Also, adsorption obeys the Langmuir isotherm.     

Corrosion inhibition by Justicia gendarussa plant extract in hydrochloric acid solution

Corrosion inhibition effect of Justicia gendarussa extract (JGPE) on mild steel in 1 M HCl medium has been investigated by weight loss and electrochemical techniques. Inhibition efficiency of 93% was achieved with 150 ppm JGPE at 25 °C. The polarization studies showed that JGPE acts as mixed-type inhibitor. The Nyquist plots showed that on increasing JGPE concentration, increases charge transfer resistance and decreases double layer capacitance. JGPE obeys the Langmuir adsorption isotherm. AFM and ESCA confirmed the adsorption of JGPE on mild steel surface. Finally, JGPE inhibition efficiency was discussed in terms of adsorption and protective film formation.     

Benzimidazole and its derivatives as corrosion inhibitors for mild steel in 1M HCl solution

In this paper, the inhibition ability of benzimidazole and its derivatives against the corrosion of mild steel in 1M HCl solution was studied. The change of impedance parameters observed by variation of inhibitors concentration within the range of 50-250 ppm was an indication of their adsorption. The thermodynamic adsorption parameters proposed that these inhibitors retard both cathodic and anodic processes through physical adsorption and blocking the active corrosion sites. The adsorption of these compounds obeyed the Langmuir’s adsorption isotherm. The inhibition efficiency was increased with inhibitor concentration in the order of 2-mercaptobenzimidazole > 2-methylbenzimidazole > benzimidazole, which is in accordance with the variation of apparent activation energy of corrosion.     

Synergistic effect of halide ions on improving corrosion inhibition behaviour of benzisothiozole-3-piperizine hydrochloride on mild steel in 0.5 M H2SO4 medium

The synergistic effect of iodide ions and benzisothiozole-3-piperizine hydrochloride (BITP) on corrosion inhibition of mild steel in 0.5 M H₂SO₄ solution has been studied by both chemical and electrochemical methods. The corrosion performance of BITP in 1.0 M HCl and 0.5 M H₂SO₄ media was examined and compared. The adsorption of BITP and its combination with iodide ions on mild steel surface followed Langmuir adsorption isotherm via chemisorption mechanism. The calculated values of synergism parameter (S_θ) were found to be greater than unity. This result clearly showed the existence of synergism between iodide ions and BITP molecules.     

A preliminary investigation of corrosion inhibition of mild steel in 0.5 M H2SO4 by 2-amino-5-(n-pyridyl)-1,3,4-thiadiazole: Polarization, EIS and molecular dynamics simulations

The efficiency, as steel corrosion inhibitors in 0.5 M H₂SO₄, of two thiadiazole derivatives, 2-amino-5-(3-pyridyl)-1,3,4-thiadiazole (3-APTD) and 2-amino-5-(4-pyridyl)-1,3,4-thiadiazole (4-APTD), was investigated by polarization and electrochemical impedance spectroscopy. The protection efficiency increases with increasing inhibitors concentration, but the temperature has hardly effect on the inhibition efficiency of APTD. The adsorption of APTD on iron surface obeys the Langmuir isotherm. The experimental results show that the inhibition efficiency of 4-APTD is higher than that of 3-APTD, and the molecular dynamics (MD) simulations show that the adsorption of 4-APTD on iron surface has the higher binding energy than that of 3-APTD.