Corrosion behaviour of silicon-carbide-particle reinforced AZ92 magnesium alloy

The corrosion behaviour of silicon-carbide-particle (SiCp) reinforced AZ92 magnesium alloy manufactured by a powder metallurgy process was evaluated in 3.5 wt.% NaCl solution, neutral salt fog (ASTM B 117) and high relative humidity (98% RH, 50 °C) environments. The findings revealed severe corrosion of AZ92/SiC/0-10p materials in salt fog environment with formation of corrosion products consisting of Mg(OH)₂ and (Mg,Al)_x(OH)_y. The addition of SiCp increased the corrosion rate and promoted cracking and spalling of the corrosion layer for increasing exposure times. Composite materials revealed higher corrosion resistance in high humidity atmosphere with almost no influence of SiCp on the corrosion behaviour.     

Corrosion behaviour of magnesium/aluminium alloys in 3.5 wt.% NaCl

Corrosion behaviour of commercial magnesium/aluminium alloys (AZ31, AZ80 and AZ91D) was investigated by electrochemical and gravimetric tests in 3.5 wt.% NaCl at 25 °C. Corrosion products were analysed by scanning electron microscopy, energy dispersive X-ray analysis and low-angle X-ray diffraction. Corrosion damage was mainly caused by formation of a Mg(OH)₂ corrosion layer. AZ80 and AZ91D alloys revealed the highest corrosion resistance. The relatively fine β-phase (Mg₁₇Al₁₂) network and the aluminium enrichment produced on the corroded surface were the key factors limiting progression of the corrosion attack. Preferential attack was located at the matrix/β-phase and matrix/MnAl intermetallic compounds interfaces.     

Electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd in NaCl solution

The electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd (x = 0, 1, 2 and 4 wt.%) alloys in 3.5% NaCl solution was investigated. The corrosion behavior of the alloys was assessed by open circuit potential measure, potentiodynamic polarization, and electrochemical impedance spectroscopy. The electrochemical results show the intermetallic precipitates with Nd behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. During corrosion, Al₂O₃ and Nd₂O₃, in proper ratio, is incorporated into the corrosion film, and enhances the corrosion resistance.     

The corrosion performance of anodised magnesium alloys

The corrosion performance of anodised magnesium and its alloys, such as commercial purity magnesium (CP-Mg) and high-purity magnesium (HP-Mg) ingots, magnesium alloy ingots of MEZ, ZE41, AM60 and AZ91D and diecast AM60 (AM60-DC) and AZ91D (AZ91D-DC) plates, was evaluated by salt spray and salt immersion testing. The corrosion resistance was in the sequential order: AZ91D ≈ AM60 ≈ MEZ ? AZ91D-DC ? AM60-DC > HP-Mg > ZE41 > CP-Mg. It was concluded the corrosion resistance of an anodised magnesium alloy was determined by the corrosion performance of the substrate alloy due to the porous coating formed on the substrate alloy acting as a simple corrosion barrier.     

Corrosion protection of magnesium alloys by cerium, zirconium and niobium-based conversion coatings

A new Ce, Zr and Nb-based conversion coating was designed for AZ91 and AM50 magnesium alloys. The corrosion protection provided by this coating was evaluated by electrochemical measurements (polarization curves, electrochemical impedance spectroscopy) in Na₂SO₄ electrolyte, and accelerated atmospheric corrosion tests (humid, SO₂ polluted air, and salt spray). Its chemical composition was characterized by X-ray photoelectron spectroscopy (XPS). Electrochemical measurements showed that Mg alloys treated during 24 h in the Ce-Zr-Nb conversion bath exhibit: (i) increased corrosion potential, (ii) decreased corrosion and anodic dissolution current densities, and (iii) increased polarization and charge transfer resistances. The accelerated corrosion tests revealed excellent atmospheric corrosion resistance for all Ce-Zr-Nb-treated samples, with or without an additional layer of epoxy-polyamide resin lacquer or paint. XPS analysis showed that the coating includes CeO₂, Ce₂O₃, ZrO₂, Nb₂O₅, MgO, and MgF₂ as main components. No significant modification of the chemical composition was observed after cathodic and anodic polarization in Na₂SO₄. This new coating provides improved corrosion resistance, and excellent paint adhesion. It offers an alternative to the chromate conversion coating for magnesium alloys.     

Corrosion behaviour in salt spray and in 3.5% NaCl solution saturated with Mg(OH)2 of as-cast and solution heat-treated binary Mg–RE alloys: RE = Ce,La, Nd,Y, Gd

Corrosion behaviour was characterised in salt spray and in 3.5% NaCl solution saturated with Mg(OH)₂ of as-cast and solution heat-treated binary Mg–RE alloys. The corrosion rate in the immersion test for the solution heat-treated Mg–RE alloys was substantial, and was greater than that of high-purity Mg. These corrosion rates were probably caused by the particles in the microstructure and/or by Fe rich particles precipitated during the solution heat-treatment. The corrosion rate in the immersion tests for each as-cast Mg–RE alloy was greater than that of high-purity Mg, attributed to micro-galvanic acceleration caused by the second phase. Corrosion rates in salt spray had a general correlation with corrosion rates in the immersion tests, but there were differences. The values of apparent valence were always less than 2 consistent with Mg corrosion being only partly under electrochemical control.     

The effect of substrate composition on the electrochemical and mechanical properties of PEO coatings on Mg alloys

Plasma electrolytic oxidation (PEO) is a unique surface treatment technology which is based on anodic oxidation forming ceramic oxide coatings on the surface of light alloys such as Mg, Al and Ti. In the present study, PEO coatings prepared on AZ91D, AZ31B, AM60B and AM50B Mg alloys have been investigated. Surface morphology and elemental composition of coatings were determined using scanning electron microscope (SEM) equipped with energy dispersive spectrometer (EDS). SEM results showed that the coating exhibited a porous top surface layer and a subsequent dense layer with micro-pores and shrinkage cracks. Phase analysis of coatings was carried out by X-ray diffraction (XRD). XRD analyses indicated that PEO coatings on AZ alloys had higher amount of Periclase (MgO) followed by the presence of Spinel (MgAl₂O₄) e.g. on the AZ91D alloy compared to that on AM series alloys. In order to examine the effect of substrate composition on adhesion strength of PEO coating scratch tests were carried out. Electrochemical corrosion tests were undertaken by means of potentiodynamic polarization technique in 3.5% NaCl solution at room temperature (20 ± 2 °C). Corrosion test results indicated that the corrosion rates of coated Mg alloys decreased by nearly two orders of magnitude as compared to bare Mg alloys. PEO coatings on AZ series alloys showed better corrosion resistance and higher adhesion properties than AM series alloys. In addition to the PEO processing parameters, such are mainly attributes of the compositional variations of the substrate alloys which are responsible for the formation, phase contents and structural properties of the PEO coatings.     

Surface spreading of intergranular corrosion on stainless steels

The spreading of intergranular corrosion was investigated using micrometer scale simulations and experimental verifications on sensitized stainless steel [UNS S30400]. The degree of sensitization, presence of a pit, and applied potential all affected spreading. The inputs used in the simulation were obtained from Fe-XCr(X = 10, 12, 14, 16 wt.%)-Mo-Ni alloys representing various grain boundary Cr depletion levels. Corroding grain boundaries and pits triggered corrosion of nearby sensitized boundaries due to Ohmic potential drop. Large connected clusters of corroding grain boundaries formed at high fractions of Cr-depleted grain boundaries. The metallurgical, electrochemical and geometric conditions for this behavior could be forecasted.     

Effect of carbon nanotubes on corrosion of Mg-CNT composites

Carbon nanotubes (CNTs) may be added to Mg matrix to produce composites of better mechanical properties, but their effect on the corrosion behaviour is not well understood. The corrosion resistance of pure Mg and its composites reinforced with 0.3 and 1.3 wt.% CNTs was studied in 3.5 wt.% NaCl solution using immersion testing and electrochemical measurements. It was found that the corrosion rate was increased considerably by the presence of CNTs because of microgalvanic action between the cathodic CNTs and the anodic Mg matrix.     

Corrosion behaviour in salt spray and in 3.5% NaCl solution saturated with Mg(OH)2 of as-cast and solution heat-treated binary Mg–X alloys: X = Mn,Sn, Ca,Zn, Al,Zr, Si,Sr

Corrosion of binary Mg–X alloys (as-cast and solution heat-treated) was characterised by immersion tests in 3.5% NaCl solution saturated with Mg(OH)₂, and by salt spray. Alloys with high corrosion rates in immersion tests also had high corrosion rates in salt spray. Corrosion rates of the solution heat-treated alloys did not meet the expectation that they should be equal to or lower than those of high-purity Mg. There was circumstantial evidence that the higher corrosion rates were caused by the particles in the microstructure; the second phases had been dissolved. The corrosion rate of all alloys was faster than that of high-purity Mg.     

Electrochemical corrosion parameters of as-cast Al-Fe alloys in a NaCl solution

The aim of this study is to evaluate the general electrochemical corrosion resistance of Al-Fe alloys in the range of hypoeutectic compositions, Al-0.5 wt.% Fe and Al-1.5 wt.% Fe alloy. EIS plots, potentiodynamic polarization curves and an equivalent circuit analysis were used to evaluate the electrochemical parameters in a 0.5 M NaCl solution at 25 °C. It is shown that for an Al-0.5 wt.% Fe alloy, coarse cells tend to improve the corrosion resistance mainly due to the reduction in cellular boundaries and for an Al-1.5 wt.% Fe alloy, an opposite trend has been detected.     

Corrosion behaviour of AIP NiCoCrAlYSiB coating in salt spray tests

NiCoCrAlYSiB coatings were deposited by arc ion plating (AIP) and annealed/pre-oxidised under various conditions. The corrosion behaviour of as-deposited and annealed/pre-oxidised coatings was studied by salt spray testing in a neutral mist of 5 wt% NaCl at 35 °C for 200 h. The results showed that the as-deposited NiCoCrAlYSiB coating behaved poorly while the annealed and pre-oxidised ones performed much better in salt spray tests. The dense microstructure in annealed coatings and formation of α-Al₂O₃ scales on the surface during pre-oxidation improved the corrosion resistance in salt spray test. The corrosion process was investigated from the aspects of corrosion products, and its electrochemical mechanism was proposed as well.     

Formation and breakdown of surface films on magnesium and its alloys in aqueous solutions

The influences of surface films formed by open-circuit exposure to neutral solutions on the corrosion and electrochemical behaviour of pure Mg and Mg alloys have been examined by in situ ellipsometric analysis and electrochemical measurements. Surface films mainly composed of Mg(OH)₂ grew rapidly during open-circuit exposure to 0.1 M NaCl and 0.1 M Na₂SO₄ solutions. These films had protective ability to passivate Mg in the solutions. However, they suffered local breakdown under anodic polarisation. The passive current density decreased and the breakdown potential increased with increasing immersion time and film thickness. Influences of purity and alloying elements on the passivity and its breakdown of Mg have been discussed.     

Electrochemical response of AlNiLa amorphous and devitrified alloys

The electrochemical response of Al_94−xNi₆La_x alloys (x = 4, 5, 6, 7) after different stages of devitrification was studied in 0.05 M Na₂SO₄ as well as in different concentrations [0.001 M, 0.01 M and 0.1 M] NaCl solutions. Complementary crystallization studies were carried out to elucidate the composition dependent phase evolution in these alloys. It was observed that the primary crystallization did not cause any deterioration in the corrosion resistance of the alloys as compared to the amorphous alloys. In the case of Al₈₇Ni₆La₇, there was actually an improvement in the passivating ability in benign media. The various primary crystalline phases in the different alloys investigated did not cause different electrochemical responses. However, the onset of secondary crystallization caused a reduction in the corrosion resistance in the NaCl media through a loss in passivating ability of all the alloys. This is due to increased galvanic activity as well as the loss of the amorphous phase.     

Corrosion behavior of Cr/Cu-coated Mg alloy (AZ91D) in 0.1 M H2SO4 with different concentrations of NaCl

An electroplating process was proposed for obtaining a protective Cr/Cu deposit on the two-phase Mg alloy AZ91D. The corrosion behavior of Cu-covered and Cr/Cu-covered AZ91D specimens was studied electrochemically in 0.1 M H₂SO₄ with different NaCl concentrations. Experimental results showed that the corrosion resistance of an AZ91D specimen improved significantly after Cr/Cu electrodeposition. The corrosion resistance of Cr/Cu-covered AZ91D decreased with increasing NaCl concentration in 0.1 M H₂SO₄ solution. After immersion in a 0.1 M H₂SO₄ with a NaCl-content above 3.5 wt.%, the surface of Cr/Cu-covered AZ91D suffered a few blisters. Cracks through the Cr deposit provided active pathways for corrosion of the Cu and the AZ91D substrate. Formation of blisters on the Cr/Cu-covered AZ91D surface was confirmed based on the results of an open-circuit potential test, which detected an obvious potential drop from noble to active potentials.     

Microstructure and corrosion performance of a cold sprayed aluminium coating on AZ91D magnesium alloy

A pure Al coating was deposited on AZ91D magnesium alloy through cold spray (CS) technique. The microstructure of the coating was characterized using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). It was found that the grain interfaces and subgrains formed close to the particle/particle boundaries. Electrochemical tests revealed that the cold sprayed pure Al coating had better pitting corrosion resistance than bulk pure Al with similar purity in neutral 3.5 wt.% NaCl solution. In addition, a mass-transfer step was found to be involved in the corrosion during 10 days immersion.     

Corrosion product formation during NaCl induced atmospheric corrosion of magnesium alloy AZ91D

Magnesium alloy AZ91D was exposed in humid air at 95% relative humidity (RH) with a deposition of 70 μg/cm⁻² NaCl. The corrosion products formed and the surface electrolyte were analysed after different exposure times using ex situ and in situ FTIR spectroscopy, X-ray diffraction and Ion Chromatography. The results show that magnesium carbonates are the main solid corrosion products formed under these conditions. The corrosion products identified were the magnesium carbonates hydromagnesite (Mg₅ (CO₃)₄ (OH)₂4H₂O) and nesquehonite (MgCO₃ 3H₂O). The corrosion attack starts with the formation of magnesite at locations with higher NaCl contents. At 95% RH, a sequence of reactions was observed with the initial formation of magnesite, which transformed into nesquehonite after 2-3 days. Long exposures result in the formation of pits containing brucite (Mg(OH₂)) covered with hydromagnesite crusts. The hydromagnesite crusts restrict the transport of CO₂ and O₂ to the magnesium surface and thereby favour the formation of brucite. Analysis of the surface electrolyte showed that the NaCl applied on the surface at the beginning was essentially preserved during the initial corrosion process. Since the applied salt was not bound in sparingly soluble corrosion products a layer of NaCl electrolyte was present on the surface during the whole exposure. Thus, Na⁺ and Cl⁻ ions can participate in the corrosion process during the whole time and the availability of these species will not restrict the atmospheric corrosion of AZ91D under these conditions. It is suggested that the corrosion behaviour of AZ91D is rather controlled by factors related to the microstructure of the alloy and formation of solid carbonate containing corrosion products blocking active corrosion sites on the surface.     

Formation of Mg,Al-hydrotalcite conversion coating on Mg alloy in aqueous HCO3/CO3 and corresponding protection against corrosion by the coating

An environmentally clean method is studied for synthesizing a conversion coating on Mg alloy in aqueous at 50 °C. A precursor layer was firstly formed on AZ91D sample. The precursor layer transformed into a crystallized Mg,Al-hydrotalcite when the sample was continuously immersed in the bath until the bath changed from acidic to alkaline. A rapid conversion treatment was, therefore, developed: it involved maintaining the pH under 6 for precursor layer formation and then increasing it to 11.5 to form crystallized Mg,Al-hydrotalcite coating. No corrosion spot on the Mg,Al-hydrotalcite-coated sample was observed after a 72-hour salt spray test.     

Corrosion behavior of equal-channel-angular-pressed pure magnesium in NaCl aqueous solution

Effect of microstructure change on corrosion behavior of equal-channel-angular-pressed (ECAPed) pure Mg was investigated. The ECAPed sample after 6 passes obtained finer grains (50-100 μm) compared with as-cast one (800-1500 μm). The strain-induced grain refinement with more crystalline defects weakened corrosion resistance of pure Mg, resulting in more and deeper pits after in-situ corrosion, higher mass-loss rate immersed in NaCl solution, larger I_corr values in polarization curves and lower fitted R_t values in EIS plots. However, the enhanced initial OCP values indicate better weather resistance. Furthermore, corrosion improvement can be expected by reducing defects via subsequent annealing.     

Corrosion behaviour of dc magnetron sputtered Fe1−xMgx alloy films in 3 wt% NaCl solution

Fe_1−xMg_x alloy films (with x ? 43.4 at.% Mg) were deposited by dc magnetron sputtering onto glass slide substrates. The objective of this study was to characterise the corrosion properties of these alloys in saline solution for application as new friendly environmentally sacrificial coatings in the protection of steel structures. The morphological and structural properties of the alloys were systematically studied prior to electrochemical experiments, and then the degraded surfaces were analysed to determine the composition and nature of corrosion products. Alloys with <25  at.% Mg were single-phase body-centred cubic (bcc) with enlarged lattice parameters, whereas for magnesium contents above 25 at.%, amorphisation occurred. The reactivity of the alloys in saline solution is strongly dependent on the Mg content and the alloy structure. The incorporation of magnesium leads to an open circuit potential shift of the alloy towards more negative values, that confers an attractive interest of these alloys as sacrificial coatings. A transition in corrosion activity is observed at 25 at.% Mg from which the reactivity decreases with the magnesium content increase. The evolution of the alloy corrosion behaviour is discussed in terms of structural and corrosion products evolution versus magnesium content.