Electrochemical behaviour of high nitrogen stainless steel in acidic solutions

The electrochemical behaviour of high nitrogen stainless steel in acidic solutions was studied by potentiodynamic polarization, EIS, Mott-Schottky and XPS. The passive film formed in neutral NaCl solution was very stable, but the stability of the film decreased with the addition of H₂SO₄ into the solution. The passive film formed in acidic Na₂SO₄ has a superior protective ability than that in acidic NaCl solution. The stability of the film formed in tested solution decreased with increase of applied potentials. The film formed on steel surface was of n-type semiconductor. Chloride penetration mechanism was proposed for the observed passive film breakdown.     

Effect of solution concentration on semiconducting properties of passive films formed on austenitic stainless steels

The semiconductor properties of passive films formed on AISI 316L in three acidic solutions were studied by employing Mott-Schottky analysis in conjunction with the point defect model (PDM). Based on PDM, the key parameters for passive film growth are the diffusivity and density of the defects within the film. The results indicated that donor densities are in the range 1-4 × 10²¹ cm⁻³ and increased with solution concentration. By assuming that the donors are oxygen ion vacancies and/or cation interstitials, the diffusion coefficient of the donors in three acidic solutions are calculated to be approximately 1-5 × 10⁻¹⁶ cm²/s.     

XPS analysis of manganese in stainless steel passive films on 1.4432 and the lean duplex 1.4162

Passive films were compared on two stainless steels: the recent lean duplex EN 1.4162 and EN 1.4432 (316L). For alloys with significant amount of manganese and nickel, the Mn 2p_3/2 peak will overlap with the Ni-LMM. To resolve this overlap, Ni 2p_3/2 to Ni-LMM intensity ratios were recorded on 1.4432, compensated for overlayer thickness, and then used to fix the Ni-LMM intensities in the Mn 2p spectra on the duplex material. Manganese was found in oxidation states II and V/VI; its film content was not dependent on the bulk composition.     

Effects of alloy and solution chemistry on the fracture of passive films on austenitic stainless steel

The Taguchi analysis method was used to simultaneously study the effects of alloy chemistry, pH, and halide ion concentrations on the fracture of electrochemically grown passive films using a nanoindentation technique. Three austenitic stainless steels, 304L, 316L, and 904L were potentiostatically polarized in hydrochloric acid solutions. The fracture load was dominated primarily by alloy chemistry. Passive films mechanically weaken as the atomic iron concentration increases in the film. Prolonged anodic ageing time increases the fracture load of passive films.     

XPS analysis of the passive film formed on austenitic stainless steel coated with conductive polymer

Improvement of the passivation behavior of Type 304 austenitic stainless steel (SS) by coating with conductive polymers (CPs), like polyaniline (PANI) and poly(o-phenylenediamine) (PoPD), followed by exposure in an acid solution has been demonstrated. The passive films formed on SSs (after peeling off the polymer layer) are compared with those formed during anodic polarization under the same exposure condition. The passive films beneath the CPs are thicker and less hydrated than those formed on uncoated stainless steel. The polymer layer enhances the enrichment of chromium and nickel in the entire passive oxide, forming a more protective film than that formed during anodic polarization. The elemental distribution within the passive film is different in the two modes of passivation. The type of the polymer influences on the composition of the passive film. The best passivation is obtained by PoPD, with the passive film resulting in significant resistance of the SS to pitting corrosion in the 3% NaCl solution. The oxide film of this steel is characterized, in its inner and outer layers, by the highest ratio of Cr(OH)₃/Cr₂O₃ and the lowest content of iron species.     

Corrosion behaviour of corrugated lean duplex stainless steels in simulated concrete pore solutions

This work studies the corrosion behaviour of two corrugated lean duplex stainless steels (SAF 2001 and 2304 grades) in eight alkaline solutions (carbonated and non-carbonated, saturated Ca(OH)₂ solutions with different chloride contents). 2001 stainless steel is a new grade in market because of its composition. 2304 is a grade previously studied under different conditions. However, its use as reinforcement in concrete is new. Studies are carried out by polarization curves following scanning electronic microscopy (SEM) and optical observations. Results are compared to those of carbon steel and austenitic AISI 304 and duplex SAF 2205 under similar conditions. After corrosion tests in alkaline media with chloride, ferrite tends to corrode selectively in 2304 duplex, while austenite corrodes selectively in 2001 under the same conditions. The influence of the duplex microstructure on attack development and morphology is analyzed. The electrochemical parameters obtained from the polarization curves suggest 2001 could replace 304 keeping the structure its corrosion performance (and with clear economical advantages). 2304 shows better corrosion behaviour than the more expensive 304, but somewhat lower than the excellent behaviour shown by 2205.     

Surface physico-chemistry study of an austenitic stainless steel: Effect of simple cold rolling treatment on surface contamination

The surface physico-chemistry properties of stainless steel and the effects of a cold rolling treatment were investigated. X-ray photoelectron spectroscopy (XPS) analyses were carried out on rolled surfaces at different rates. Thus, by characterizing passive film chemistry and contamination layer, the modifications due to this treatment were quantified, in particular an increase of the ratio (Fe/Cr)_oxide is evidenced with the level of the cold rolling treatment. Moreover, based on an angle resolved analysis, a new model where the contamination layer is represented as isolated parts was developed in order to describe the geometry of this carbon contamination. XPS experiments show an iron enrichment of the passive film during the cold rolling treatment, which seems to be explained by a surface heating during the mechanical treatment. Therefore, the new island model puts in evidence the effects of ageing time and surface condition on the geometry of carbon contamination. Hence, cold rolling increases the thickness and the recovery of carbon contamination on the stainless steel surface.     

Direct imaging of native passive film on stainless steel by aberration corrected STEM

A cross-section of a native passive film on a commercial type 304 stainless steel was directly imaged and characterized using an aberration corrected STEM-EDS in combination with FIB sectioning. The technique demonstrated an enrichment of Cr in the lower part of the passive film, and a depletion of Cr and an enrichment of Ni in the matrix side closest to the passive film/matrix interface in accordance with previous studies, further proving the advantage of this technique with respect to spatial resolution. That is, the STEM-EDS showed a compositional profile with higher spatial resolution compared to AES which has been mainly used for this type of investigation. The technique will be applicable to the investigation of nm to sub-nm compositional fluctuation of passive films, steel surfaces adjacent to inclusions and grain boundaries postulated as an initiating site of pitting corrosion or stress corrosion cracking (SCC).     

Electrochemical polishing as a 316L stainless steel surface treatment method: Towards the improvement of biocompatibility

A 316L stainless steel (316L-SS) surface was electrochemically polished (EP) in an electrolyte of a new chemical composition at different cell voltages, with the aim of improving its corrosion resistance and biocompatibility. X-ray photoelectron spectroscopy results revealed that the EP-formed oxide films were characterized by a significantly higher atomic Cr/Fe ratio and film thickness, in comparison to the naturally-grown passive oxide film formed on the untreated (control) 316L-SS surface. As a result of the increase in the oxide film thickness and relative Cr enrichment, the EP-treated 316L-SS surfaces offered a notable improvement in general corrosion resistance and pitting potential. In addition, the attachment of endothelial cells (ECs) and smooth muscle cells (SMCs) to the 316L-SS surfaces revealed a positive effect of electropolishing on the preferential attachment of ECs, thus indicating that the EP surfaces could be endothelialized faster than the control (unmodified) 316L-SS surface. Furthermore, the EP surfaces showed a much lower degree of thrombogenicity in experiments with the platelet-rich plasma. Therefore, the use of the electrochemical polishing technique in treating a 316L-SS surface, under the conditions presented in this paper, indicates a significant improvement in the surface’s performance as an implant material.     

High corrosion resistance of austenitic stainless steel alloyed with nitrogen in an acid solution

Passivity of austenitic stainless steel containing nitrogen (ASS N25) was investigated in comparison with AISI 316L in deareated acid solution, pH 0.4. A peculiar nature of the passivation peak in a potentiodynamic curve and the kinetic parameters of formation and growth of the oxide film have been discussed. The electronic-semiconducting properties of the passive films have been correlated with their corrosion resistance. Alloying austenitic stainless steel with nitrogen increases its microstructure homogeneity and decreases the concentration of charge carriers, which beneficially affects the protecting and electronic properties of the passive oxide film.     

Photocurrent and capacitance investigations into the nature of the passive films on austenitic stainless steels

Photocurrent and capacitance measurements of semiconductor passive films formed on metals and alloys can be used to study the electronic properties and reveal indirect information about structure and composition. The current work used these techniques to investigate the electronic properties of the passive films formed on three austenitic stainless steels, types 304L, 316L and 254SMO, in borate. Evidence was found for the existence of a large number of localised mid bandgap states, consistent with amorphous oxides. However, the flat-band potentials of the austenitic stainless steel passive films were found to be independent of both composition and measuring frequency. The most credible explanation for the bandgap values determined from photocurrent measurements is that the passive films are formed as dual layers, iron oxide outer layer and chromium oxide inner layer. This model does not need to evoke the potential dependent bandgaps used by previous authors.     

The semiconducting properties of passive films formed on AISI 316 L and AISI 321 stainless steels: A test of the point defect model (PDM)

The semiconductor properties of passive films formed on AISI 316L in 1 M H₂SO₄ in three temperatures and AISI 321 in 0.5 M H₂SO₄ were studied by employing Mott–Schottky analysis in conjunction with the point defect model (PDM). Based on the Mott–Schottky analysis in conjunction with PDM, it was shown that the calculated donor density decreases exponentially with increasing passive film formation potential. Also, the results indicated that donor densities increased with temperature. By assuming that the donors are oxygen ion vacancies and/or cation interstitials, the diffusion coefficients of the donors for two stainless steels are calculated.     

Soft X-ray absorption spectroscopy study of the effects of Si, Ce, and Mo ion implantation on the passive layer of AISI 304 stainless steel

The chemical modifications introduced in the passive layer of AISI 304 stainless steel after Si, Ce, and Mo ion implantation were investigated and compared with non-implanted steel by soft X-ray absorption spectroscopy. The influence of ion implantation on the passive properties was evaluated by measuring soft X-ray absorption spectra at the Cr, Fe, Ni, Mn and Si 2p in addition to oxygen 1s thresholds. All ion implanted samples show a relative Cr-enrichment at the surface as compared with non-implanted samples. Fe 2p as well as O 1s spectral changes reveal chemical differences in the passive layer as a function of the element ion-implanted.     

Nanostructure and local properties of oxide layers grown on stainless steel in simulated pressurized water reactor environment

The morphology and local electrical resistance of duplex oxide films formed on 316L stainless steel at 325 °C in simulated primary coolant of pressurized water reactor have been investigated at the nanometre scale with Conductive Atomic Force Microscopy. The electrical resistance varies over ∼1 order of magnitude for most oxide grains and over 2–3 orders of magnitude locally at grains and grain boundaries. This is rationalized in terms of local variation of the composition and thus resistivity of the mixed Fe(II)–Cr(III) barrier inner layer of the oxide films with grain boundaries of the outer layer possibly promoting Cr(III) enrichment.     

Surface chemistry and corrosion behaviour of 304 stainless steel in simulated seawater containing inorganic sulphide and sulphate-reducing bacteria

Although many studies have been carried out regarding the role of sulphide anions in promoting microbial corrosion of various metal substrates, very little is known about the differences between inorganic sulphide and biogenically-derived sulphide by sulphate-reducing bacteria (SRB) and what the reasons for differing corrosion behaviour between the two types of sulphide may be towards common metals. In this study, various electrochemical and surface analytical techniques were employed to study the effect of the inorganic and biogenic sulphide (active SRB present) on the surface chemistry and corrosion behaviour of 304 stainless steels in a simulated seawater-based modified Baar’s (SSMB) medium. Clear differences in the surface chemistry of the sulphurised passive film by inorganic and biogenic sulphide (active SRB present) were quantified by X-ray photoelectron spectroscopy (XPS). The transformation of metal sulphides in abiotic and biotic sulphide solutions with the exposure time was correlated with different corrosion behaviour of 304 stainless steels.     

Effect of sulphide on the corrosion behaviour of AISI 316L stainless steel and its constituent elements in simulated Kraft digester conditions

The electrochemical behaviour of AISI 316L steel and its constituent metals in simulated Kraft digester white liquor at 170 °C has been studied by registering slow scan rate voltammograms and impedance spectra at the corrosion potential. Interpretation of the results in terms of two approaches - the Mixed-Conduction Model for passive films and a two-step dissolution reaction - allowed for the estimation of corrosion currents and polarisation resistances as depending on the material and electrolyte medium. Tentative conclusions on the effect of sulphur-containing species in the white liquor on the corrosion mechanism of the studied materials are drawn.     

Hydrogen effects on stainless steel passive film fracture studied by nanoindentation

Hydrogen effects on the fracture stress of passive film formed on 316L stainless steel were studied by nanoindentation. Hydrogen accumulated primarily on the sample surface and in the passive film. Displacement excursion related to film fracture appeared in load-controlled load–displacement curves when electrochemically polished and anodically passivated samples were indented. The excursion disappeared after the passivation film was removed electrochemically or by nanowear. The critical load, excursion depth and length decreased with higher hydrogen concentration, along with Young’s modulus and fracture stress of the passive film.     

Factors that influence the release of metals from stainless steels exposed to physiological media

Release rates of chromium, nickel and iron from grade 304 stainless steel with three different surface finishes, BA, 2B and 2D, have been determined after exposure to artificial lysosomal fluid. Metal release rates are discussed in relation to corrosion resistance, compositional changes of the outermost surface film of the stainless steel and to measurements of the effective surface area and roughness. The total metal release decreased in the following sequence: 2D > 2B ≈ BA, and was primarily related to the electrochemically active surface area. No direct correlation was observed between corrosion resistance and metal release rates.     

Metal release from various grades of stainless steel exposed to synthetic body fluids

Release rates of individual alloy constituents have been determined from seven grades of stainless steels exposed to two synthetic body fluids, used as surrogates for different areas of potential exposure in the lung: “Gamble’s solution”, (pH 7.4) that represents the interstitial fluid of the deep lung, and artificial lysosomal fluid (ALF) that represents the more acidic (pH 4.5-5) milieu of particles following their phagocytosis by macrophages. Total metal release rates from all grades of stainless steel investigated were low (<5 μg cm⁻² week⁻¹). The more acidic environment of ALF resulted in significantly higher total metal release rates (0.3-4.6 μg cm⁻² week⁻¹) compared to Gamble’s solution (<0.1 μg cm⁻² week⁻¹).     

Depth profile analysis of thin passive films on stainless steel by glow discharge optical emission spectroscopy

Thin passive films formed on highly corrosion-resistant type-312L stainless steel, containing 20 mass% chromium and 6 mass% molybdenum, in 2 mol dm⁻³ HCl solution at 293 K have been analyzed by glow discharge optical emission spectroscopy (GDOES). The stainless steel does not suffer pitting corrosion even in this aggressive solution, showing a wide passive potential region. The depth profiles obtained clearly show a two-layer structure of the air-formed and passive films: an outer iron-rich layer and an inner layer highly enriched in chromium. Alloy-constituting molybdenum is deficient in the inner layer of the passive films and is enriched in the outer layer, particularly at the active dissolution potential. The molybdenum species in the outer layer may retard the active dissolution of stainless steel, promoting the formation of stable passive films highly enriched in chromium. Chloride ions are present only at the outermost part of the passive films, not penetrating into the interior part.