The characteristics of primary and secondary arcs on a solar array in low earth orbit

In this paper, the characteristics of the primary arc and secondary arc on a solar array in low earth orbit(LEO) are investigated. The vacuum plasma environment in LEO has been used to study the primary arc and secondary arc of a high-voltage solar array. Silicon solar cells with rigid substrate specimens are used for the experiment. The series-parallel spacing of the silicon solar cells is 1 mm. The string currents of the solar cells are 0.7 A, 1.5 A and 2 A. The primary arc and secondary arc are photographed by high-speed cameras. The differences between the primary arc and secondary arc are observed. The secondary arc can be observed before the primary arc is extinguished. The primary arc is a single arc when the string current is 0.7 A. Multiple arc columns are accompanied by higher arc current. Two arc columns of the primary arc can be observed at 1.5 A string current and 2 A string current. The multiple primary arc columns are related to higher bias voltage. The threshold for sustained arcing is near 145 V/0.7 A, 105 V/1.5 A and 100 V/2 A at 1 mm string gap. Moreover, the transition time of secondary arc formation is analyzed, and found to be about 10–13 μs. The string currents, string voltages and primary arc have no effect on the transition time of the secondary arc formation.     

Properties of intermediate-frequency vacuum arc in sinusoidal curved contact and butt contact

In this report,two new contact structures of a vacuum interrupter with a sinusoidal curved surface are proposed to improve the capability by increasing the surface area.The experimental investigation of vacuum arc at intermediate frequency(360-800 Hz)was conducted and the results were compared with a butt contact with the same contact diameter(41 mm)and the same material.By analyzing the arc behavior,arc voltage characteristics,arc energy,current interrupting capacity,ablation of the anode contact and condensation of the arc products at a 3 mm gap,the differences in their vacuum arc characteristics were determined.The correlations of their arc energy with the amplitude and the frequency of the current were also achieved.Analysis suggests that the ruled curved contact has strong application potentiality because of its low arc energy,low arc voltage noise and arc voltage peak,light ablation on the surface of the anode contact and high interrupting capacity.     

Interruption Phenomenon in Intermediate-Frequency Vacuum Arc

In the condition of the 3 mm gap, experiments for 360 Hz intermediate-frequency vacuum arc are carried out in interrupters with the diameters being 41 mm and with the contact materials being CuCr50 and Cu-W-WC alloy respectively. The results indicate that the contacts material is closely related to the breaking capacity of the vacuum interrupters and characteristics of an intermediate-frequency vacuum arc. For contacts with the same diameter, the breaking capacity of CuCr50 is better than that of Cu-W-WC. When the current fails to be interrupted, the arcs overflow the gap and present irregular performances in the first half wave. Consequently a voltage spike appears. More macroscopic metal droplets can be seen in the arc column between CuCr50 contacts because of the lower melting point. It is observed that the droplet emission is much more severe during arc reignition than that in the first half wave. It is much more conspicuous that the high frequency arc voltage noises appear in Cu-W-WC contacts when the vacuum arcs reignite, for higher temperature and stronger electronic emission ability of Cu-W-WC contacts.     

Effects of background pressure on the arc characteristics of gas spark gap

Gas spark gap is widely used in any pulsed power system as the key element which directly determines its repetitive performance and output characteristics. Among many factors of threeelectrode gas spark gap, background pressure is of much importance in determining the gap performance parameters such as the delay and jitter, and relevant studies have been rarely performed. A magneto-hydrodynamic model of the arc in gas spark gap is built and the effects of background pressure on the arc characteristics are discussed in this paper. It is demonstrated that a higher background pressure may result in radial compression of the arc column, a higher arc voltage, and a lower declination rate of arc resistance in the first quarter cycle. Relevant simulation data would be helpful for the optimization of the design of gas spark gap.     

Characteristic Analysis of AC Plasma Arc in Water

An experimental system of AC arc discharge in water was designed with pole-pole electrodes and a peak voltage of 1500 V and a test circuit was set up using virtual instrument technology. The mechanism of an AC plasma arc generated in water was analyzed. The voltage- current characteristic of the AC plasma arc was obtained from the waveform. The temperature characteristic was tested with a spectrum diagnosis system, and the effect of different electrode materials on the striking voltage and peak current was analyzed. The results show that when a power supply of 6 KW is applied on electrodes with a gap of 2 mm in water, the striking voltage is from 900 to 1300 V, the arc voltage is from 40 to 100 V, the arc current is from 2 to 7 A, and the zero rest period is from 1 to 2 ms. In addition, the arc voltage and current are different for electrodes in aluminum, copper and stainless steel. The arc voltage is lower and the current is higher for an aluminum electrode than those for copper and stainless steel ones. The highest temperature of the arc is 7643 K.     

Design and characteristics of a new type laminar plasma torch for materials processing

Laminar plasma jet(LPJ) generated by laminar plasma torch(LPT) has a favorable temperature and velocity distribution. Thus, it is superior to the turbulent plasma jet in material processing.However, most of the reported LPTs usually operate at a relatively low output power with a relatively low arc voltage and thermal efficiency, which limits its capabilities. In this context, this paper attempts to design a new type of high-power LPT with a relatively low arc current and a high thermal efficiency. In the first section, the design principle of the main components is studied and discussed in detail, and a new high-power LPT is proposed. Then, the experimental characteristics of the proposed high-power LPT are examined. Experimental results reveal the following characteristics of the proposed LPT.(1) The max jet length of the proposed LPT reaches at 540 mm.(2) Its mean arc voltage is higher than 290 V when the LPT works with arc currents lower than 200 A, leading to an output power greater than 50 kW.(3) The mean thermal efficiency is higher than 50%. Lastly, the proposed LPT has been applied to spheroidize the aluminum oxide powers. The experiment results for the production of spherical powders show that the proposed LPT has a good characteristic for material processing.     

Typical Motion and Extinction Characteristics of the Secondary Arcs Associated with Half-Wavelength Transmission Lines

Secondary arc discharge is a complicated physical phenomenon and one of the key fundamental issues associated with ultra high voltage （UHV） half-wavelength transmission lines （HWTL）. With the establishment of a physicM simulation platform for the HWTLs, experiments were carried out regarding the motion and extinction characteristics of secondary arcs. The cathode arc root and the anode arc root were found to show an obvious polarity effect while the arc column was moving in a spirM, due to their different motion mechanisms. The extinction behavior was also recorded and experiments were designed with different compensation conditions. Results show that the arcing time can be greatly reduced if there exists an electrical compensation network. The research provides fundamentals for understanding the physics involved, especially the motion and extinction mechanisms of the secondary arcs.     

Convection effect on an arc plasma evolution process in a two parallel contact system

A low voltage circuit breaker(LVCB) is an important piece of protection equipment which will switch off the fault current in a power system. The moving contact of a low voltage circuit breaker with a higher rated current consists of two parallel contacts. Therefore, the convection effect on the air arc evolution process in a two parallel contact system is analyzed. A threedimensional(3 D) magneto–hydro–dynamic(MHD) model of arc simulation is built. In this model, the anode consists of two parallel contacts and a bonding conductor. A nonlinear voltage–current density characteristic is employed to represent the near-anode and near-cathode voltage. The current density, arc voltage and currents through every contact are obtained. The influence of convection and conduction on the arc evolution process are quantitatively calculated. The displacements of the arc roots are obtained and the asymmetry of the arc root motion is analyzed. The arc evolution process of a two parallel contact system is preliminarily revealed.     

Arc characteristics during the instability stage on transverse magnetic field contacts

The arcing process greatly affects the breaking ability after current zero. The instability stage is the transition stage from the ignition to the movement stage, which affects the arc movement characteristics. In this paper, the arc characteristics during the instability stage on spiral-type contacts were investigated using a high-speed video camera. A multi-column parallel instability mode and a single-column instability mode were found during the instability stage. The arc appearance and constriction degree changed rapidly. The arc voltage usually increased accompanied by fluctuations. In addition, it was found that the current significantly influenced the arc mode and duration in the instability stage. With increased peak current, the probability of a single-column instability mode increased, and the fluctuation range and average time decreased.     

Study of Distortion of a Vacuum Arc at a Long-Gap Distance

Experimental study of the long-gap distance vacuum arc distortion for three types of axial magnetic field (AMF) contacts, by using high-speed charge coupled device (CCD), is presented. The arc current was of a half-cycle sine wave with a frequency of 50Hz, produced by an L-C discharging circuit. The time of appearance and duration of vacuum arc distortion under three conditions were studied. It was found that the gap distance, current and diameter of the electrode affected the characteristics of vacuum distortion at a long-gap distance. Some characteristics of the vacuum arc at a long-gap distance was revealed and the experience and data for further investigation were provided.     

Experimental investigation of thermal transfer coefficient by a simplified energy balance of fault arc in a closed air vessel

The themial transfer coefficient that represents the portion of energy heating the surrounding gas of fault arc is a key parameter in evaluating the pressure effects due to fault arcing in a closed electrical installation.This paper presents experimental research on the thermal transfer coefficient in a closed air vessel for Cu,Fe and A1 electrode materials over a currcni range from 1-20 kA with an electrode gap from 10-50 mm and gas pressure from 0.05-0.4 MPa.With a simplified energy balance including Joule heating,arc radiation,ihc energies related to electrode melting,vaporization and oxidation constructed,and the influences of different factors on thermal transfer coefficient are studied and evaluated.This quantitative estimation of the energy components confirmed that the pressure rise is closely related to the change in heat transport process of fault arc.particularly in consideration of the evaluation of Joule healing and radiation.Factors such as the electrode material,arc current,filling pressure and gap length between electrodes have a considerable effect on the thermal transfer coefficient and thus,the pressure rise due to the differences in the energy balance of fault arc.     

The Influence of Contact Space on Arc Commutation Process in Air Circuit Breaker

In this paper,a 3D magneto-hydrodynamic (MHD) arc simulation model is applied to analyze the arc motion during current interruption in a certain air circuit breaker (ACB).The distributions of pressure,temperature,gas flow and current density of the arc plasma in the arc region are calculated,and the factors influencing the commutation process are analyzed according to the calculated results.Based on the airflow in the arc chamber,the causes of arc commutation asynchrony and the back commutation are investigated.It indicates that a reasonable contact space design is crucial to a successful arc commutation process.To verify the simulation results,the influence of contact space on arc voltage and arc commutation is tested.This research can provide methods and references to the optimization of ACB design.     

Critical Length Criterion and the Arc Chain Model for Calculating the Arcing Time of the Secondary Arc Related to AC Transmission Lines

The prompt extinction of the secondary arc is critical to the single-phase reclosing of AC transmission lines,including half-wavelength power transmission lines.In this paper,a lowvoltage physical experimental platform was established and the motion process of the secondary arc was recorded by a high-speed camera.It was found that the arcing time of the secondary arc rendered a close relationship with its arc length.Through the input and output power energy analysis of the secondary arc,a new critical length criterion for the arcing time was proposed.The arc chain model was then adopted to calculate the arcing time with both the traditional and the proposed critical length criteria,and the simulation results were compared with the experimental data.The study showed that the arcing time calculated from the new critical length criterion gave more accurate results,which can provide a reliable criterion in term of arcing time for modeling and simulation of the secondary arc related with power transmission lines.     

Motion and Splitting of Vacuum Arc Column in Transverse Magnetic Field Contacts at Intermediate—Frequency

Arc motion and splitting of vacuum arc at intermediate frequency（400-800 Hz） were investigated under transverse magnetic field（TMF）.The experiment was performed on cup-type TMF contacts with contact diameter of 40 mm and a contact gap of 4 mm in a single-frequency circuit.With high-speed photography we characterized the arc appearance at different arc currents from 3.3 kA-rms to 10 kA-rms at intermediate frequencies.As arc current increases from3.3 kA-rms to 10 kA-rms the arc appearance changes obviously.When current value is 3.3 kArms（current frequency 400-800 Hz）,there is almost no splitting arc;when the current exceeds5 kA-rms（current frequency 400-800 Hz）,the arc rotates at a speed above 20 m/s,accompanied by an observable splitting arc.The splitting arc could be observed at different frequencies and the arc-voltage had no noises when splitting occurred.The motion direction and the velocity of arc column were studied.Finally,the formation of a split arc was discussed.     

Two-dimensional self-consistent numerical simulation of the whole discharge region in an atmospheric argon arc

A 2D self-consistent numerical model of the whole argon-arc discharge region that includes electrodes is developed in this work to facilitate analysis of the physical processes occurring in atmospheric arc plasma. The 2D arc column model contains the ionization and thermal non-equilibrium, which is coupled with a 1D electrode sheath model. The influence of plasma-species diffusion near the electrode region is investigated based on Maxwell–Stefan equations and the generalized Ohm's law. The numerical results of argon free-burning arcs at atmospheric pressure are then investigated. The simulation shows that the plasma is obviously in the state of thermal and ionization equilibrium in the arc core region, while it deviates from thermal and ionization equilibrium in the arc fringe region. The actual electron density decreases rapidly in the near-anode and near-cathode regions due to non-equilibrium ionization, resulting in a large electron number gradient in these regions. The results indicate that electron diffusion has an important role in the near-cathode and near-anode regions. When the anode arc root gradually contracts, it is easy to obtain a positive voltage drop of the anode sheath (I = 50 A), while it remains difficult to acquire a positive anode sheath voltage drop (I = 150 A). The current–voltage characteristics predicted by our model are found to be identical to the experimental values.     

Evaporation Erosion During the Relay Contact Breaking Process Based on a Simplified Arc Model

Evaporation erosion of the contacts is one of the fundamental failure mechanisms for relays.In this paper,the evaporation erosion characteristics are investigated for the copper contact pair breaking a resistive direct current (dc) 30 V/10 A circuit in the air.Molten pool simulation of thc contacts is coupled with the gas dynamics to cMculate the evaporation rate.A simplified arc model is constructed to obtain the contact voltage and current variations with time for the prediction of the current density and the heat flux distributions flowing from the arc into the contacts.The evaporation rate and mass variations with time during the breaking process are presented.Experiments are carried out to verify the simulation results.     

Analysis of Effects of the Arc Voltage on Arc Discharges in a Cathode Ion Source of Neutral Beam Injector

A hot cathode bucket ion source is used for the EAST(experimental advanced superconducting tokamak)neutral beam injector.The thermal electrons emitted from the surface of the cathode are extracted and accelerated by the electric field formed by the arc voltage,which is applied between the arc chamber of the ion source and the cathode.This paper analyzes the effects of arc voltage on the arc discharge in a hot cathode high current ion source.     

Investigation on the Arc Ignition Characteristics and Energy Absorption of Liquid Metal Current Limiter Based on Self-Pinch Effect

The GaInSn liquid metal current limiter based on the fluid pinch effect has broad application prospects due to its particular properties.However,the limited rated current and ability of power dissipation are the critical problems for its wide application.Firstly,the temperature distribution of the liquid metal current limiter (LMCL) was obtained by experiments with a rated current of 1 kA and the arc ignition phenomenon was observed with 1.5 kA,which indicates that the rated current is mainly limited by the arc rather than the high temperature compared to the traditional switchgears.Furthermore,an improved method is proposed by adding the paralleled pure resistance,impedance or another LMCL element to protect the setup from the fault energy concentration in the setup.The problem of a slower arc voltage increasing rate can be solved by adding a paralleled impedance with suitable parameters.Finally,the current limiting properties based on the improved method were investigated and the alternating oscillating current was found between two paralleled LMCL elements owing to their deviation of arc ignition in reality.     

Dynamic behavior of a rotating gliding arc plasma in nitrogen: effects of gas flow rate and operating current

The effects of feed gas flow rate and operating current on the electrical characteristics and dynamic behavior of a rotating gliding arc (RGA) plasma codriven by a magnetic field and tangential flow were investigated.The operating current has been shown to significantly affect the time-resolved voltage waveforms of the discharge,particularly at flow rate =21 min-1.When the current was lower than 140 mA,sinusoidal waveforms with regular variation periods of 13.5-17.0 ms can be observed (flow rate =21 min-1).The restrike mode characterized by serial sudden drops of voltage appeared under all studied conditions.Increasing the flow rate from 8 to 121 min-1 (at the same current) led to a shift of arc rotation mode which would then result in a significant drop of discharge voltage (around 120-200 V).For a given flow rate,the reduction of current resulted in a nearly linear increase of voltage.     

Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

In this work,a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions.The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals,high speed photography,and optical emission spectroscopic diagnostics.Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g.,10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone,in this RGA system,a lower gas flow rate (e.g.,2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions.Two different motion patterns can be clearly observed in the N2 and air RGA plasmas.The time-resolved arc voltage signals show that three different arc dynamic modes,the arc restrike mode,takeover mode,and combined modes,can be clearly identified in the RGA plasmas.The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.