共查询到20条相似文献,搜索用时 125 毫秒
1.
阐述了在LabView程序开发环境下完成三个功能模块的设计。网络数据处理模块:具有对控制器传来数据的数据库管理功能。信号采集及波形显示和分析模块:主要是对几种基本波形(正弦波、方波、三角波、锯齿波等)的采集,并对采集的信号进行分析和存储。信号输出控制模块:主要是针对采集后存储的数据进行还原,输出波形。 相似文献
2.
阐述了在LabView程序开发环境下完成三个功能模块的设计。网络数据处理模块:具有对控制器传来数据的数据库管理功能。信号采集及波形显示和分析模块:主要是对几种基本波形(正弦波、方波、三角波、锯齿波等)的采集,并对采集的信号进行分析和存储。信号输出控制模块:主要是针对采集后存储的数据进行还原,输出波形。 相似文献
3.
为实现一个高采样率,宽频带的便携式数字存储示波器,设计了以STM32为控制核心的数字示波器。硬件平台主要采用了AD8260数字程控增益放大器作为前端信号调理电路,ADS830高速宽带模数转换器和IDT7204高速缓存作为数字采集电路,以及信号波形采用了TFT彩屏显示。另外,通过采用数字内插的数字信号处理算法来重建和还原信号波形,进而改善了信号波形显示细节。最后对研制样品进行了实验室测试,实验结果表明硬件设计思路与软件及算法的处理是正确的,性能参数达到设计要求,可以应用在工程实践中。 相似文献
4.
用PC直接获取数字示波器波形和联机波形参数测量 总被引:1,自引:0,他引:1
数字存储示波器,顾名思义除了能实现一般的显示波形功能之外,更重要的是能将屏幕上显示的波形保存下来,以便作再次观察和其它用途,这是数字存储示波器和普通示波器的根本区别。据了解,一般的数字存储示波器用户,都会使用它进行测量和观察波形,对如何存储波形的方法并没有去研究或不太了解。本文提供了利用电脑与安捷伦数字存储示波器实现联机,并利用电脑直接将示波器的波形存储下来,和对存储下来的波形进行参数测量分析等方法,对数字存储示波器用户有一定的参考价值。 相似文献
5.
本文选用LabVIEW图形化编程语言为开发软件,设计了一个用于日常教学的虚拟信号发生器。该仪器可以模拟产生正弦波、锯齿波、方波、三角波、等4种基本波形和任意的公式波形,并且各波形均可以调整其参数值的大小,其中频率范围还具有档位可调功能。该仪器所产生的波形可以以LabVIEW测试文件形式存储进行存储。 相似文献
6.
本文选用LabVIEW图形化编程语言为开发软件,设计了一个用于日常教学的虚拟信号发生器。该仪器可以模拟产生正弦波、锯齿波、方波、三角波、等4种基本波形和任意的公式波形,并且各波形均可以调整其参数值的大小,其中频率范围还具有档位可调功能。该仪器所产生的波形可以以LabVIEW测试文件形式存储进行存储。 相似文献
7.
数字示波器中的波形存储、录制与回放 总被引:1,自引:1,他引:0
波形存储、录制与回放是数字示波器的重要功能。在此采用闪速存储器(FLASHMemory)存储重要的波形数据,方便用户事后调出观察、分析和对比。每段波形存储的长度固定,根据存储波形的序号、大小、起始地址等建立波形存储索引表,通过查询波形索引表可选择要回放的波形。还可以通过波形录制功能把信号波形录制到静态数据存储器(SDRAM)中,然后回放波形,寻找并观察自己需要的波形。通过直接存储(DMA)方式实现将显示缓冲区存储的波形搬移到波形录制的缓存中去,实现了数据的高速存储。在手持式示波表的研制过程中实现了此波录制和回放方法达到了预期的效果。 相似文献
8.
9.
这里设计是以C8051F020单片机最小系统为核心,将采集到的波形信号通过C8051F020集成的模数转换(A/D)、数模转换(D/A)完成相应的信号转换,并将波形信号存储于外接的MB85RS256存储器中,实现波形采集、存储和回放的功能。同时,系统外扩(LCD,LiquidCrystalDisplay),在LCD上显示波形信号的周期和峰峰值。该系统能够同时采集两路信号波形,并按先后顺序存储在存储器中,读取存储器实现两路信号波形的回放功能。实验结果表明,该系统能够实现相应的功能,性能安全,可靠。 相似文献
10.
有些波形只出现一次,或不具固定频率,要记录或捕获这些波形,通常采用的方法就是使用逻辑分析仪,或使用存储式示波器。但是,这两种仪器都很昂贵。再者,由于其存储容量有限,存储式示波器只能记录不到1000个采样值。本文所提出的技术,提供了记录数字波形的另外一种方法。其设计思想是采用PC机的打印口来对数字波形进行采样,并用PC的内存来存储采样数据。PC的大内存容量可存储大量的采样。例如,60kb的存 相似文献
11.
A software network model with multiple links is constructed on the basis of a dynamical model of a general complex network with multiple links. The principle of network division of multiple links is introduced. Following these principles, the software network model is decomposed into three types of subnets and different relationships between classes are revealed. Then, the dynamic analysis of software networks is presented. A sufficient condi-tion for the stability of general complex networks is obtained followed by that of software networks. Fi-nally, the dynamics of an open-source software sys-tem is analyzed, and their simulations are provided to demonstrate the effectiveness of the presented model. 相似文献
12.
通过分析比较目前应用广泛的几种计算机仿真软件,重点介绍SystemView的优势及其主要功能模块库和应用领域,结合通信系统实例,介绍了该软件的使用方法及注意事项。总结了该软件的教学应用效果及对相关课程教学的借鉴作用,适合通信系统的仿真与设计。 相似文献
13.
14.
The problems of traditional software-development paradigms are examined, identifying areas which can be helped by knowledge-based techniques. A discussion on fundamental software issues which relate to knowledge-based approaches to software development is presented. Based on this discussion, a framework for knowledge-based software development paradigms and tools, and a development environment to support the paradigm are provided 相似文献
15.
Schneidewind N.F. 《Proceedings of the IEEE. Institute of Electrical and Electronics Engineers》1989,77(4):618-624
Hardware and software maintenance are contrasted. The key difference between the two-the ease with which software can be changed-leads to the need for managing software change. Standardization of software maintenance is proposed as a method for managing software change. A model of software maintenance is advanced as the foundation for standardizing software maintenance 相似文献
16.
《Proceedings of the IEEE. Institute of Electrical and Electronics Engineers》1973,61(11):1570-1574
Software implementation for automatic test systems controlled by minicomputers can be a costly and time-consuming process. A procedure for implementing software which tends to minimize costs and avoid delays caused by unexpected problems is described. The procedure consists of completely defining the test system functions and performing a series of hardware versus software tradeoffs during the design and implementation process. The purpose of the tradeoffs is to determine the least costly method of implementing tester functions by either hardware, software, or some combination of hardware and software. Delays caused by unexpected problems are reduced by including hardware and software debugging aids which shorten the time to validate the tester system functions. An example of implementing an automatic test system in accordance with these procedures is provided. 相似文献
17.
18.
19.
Redundant control systems require more than a single redundant construct to serve the six basic functions of fault tolerance: test, detection, diagnosis, masking, reconfiguration, and recovery. Software usually constitutes or supports one or more such constructs. Additionally, software must be correct, since it is seldom, if ever, protected by redundancy. A redundant sequential control system requires intricate software constructs. The predominant existing software specification and implementation techniques for sequential control are not adequate for the creation of correct software of the complexity required for redundant systems. This complexity is illustrated by an example. 相似文献
20.
根据软件无线电技术的思想,提出了一种依托通用的可编程硬件平台,以各种软件模块实现不同标准信号通信的多速率、多模式的卫星通信终端的设计。详细讨论了该设备的软、硬件结构设计,并对所涉及的开放式的总线结构、宽带A/D、D/A转换技术、高速数字信号处理技术、功能软件模块化编程设计等关键技术进行了分析。 相似文献