模板法合成分叉Ni纳米线阵列及其磁性能

首先采用三次阳极氧化法制备了具有Y形孔道的氧化铝(AAO)模板,然后采用直流电化学沉积法,在模板内成功合成了分叉Ni纳米线的有序阵列.通过X射线衍射仪(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对所合成样品的晶体结构和形貌进行了表征测试.结果表明,制备的Ni纳米线分布均匀、排列有序,呈Y形分又结构,其...     

CuS纳米线阵列的制备

将多孔阳极氧化铝模板(AAO)的电化学沉积技术与真空硫化技术相结合,在制备Cu纳米线的基础之上,制备得到了CuS纳米线阵列.采用扫描电子显微镜电镜和X射线衍射仪对二次氧化的AAO模板和所得Cu与CuS纳米线的形貌和结构进行了表征,结果表明所得CuS纳米线不仅具有良好的有序阵列,而且具有多晶结构.在硫化过程中,随着硫化温度的升高,CuS结晶程度增大,在500～550℃时,达到最大的结晶程度.     

交流电沉积制备SnO2纳米线及其电沉积条件研究

采用阳极氧化的方法制备了孔径为30～50nm多孔阳极氧化铝(AAO)模板,用交流(AC)电沉积法在氧化铝模板孔洞内沉积金属锡,然后在空气中750℃加热含锡的模板10h,热氧化制备了直径在30～50nm SnO2纳米线．用扫描电子显微镜,透射电子显微镜,X射线衍射仪对所制备的SnO2纳米线进行了表征,表明所制备的纳米线为多晶结构．并通过改变交流电沉积过程中的电压,频率和热氧化时间来考察不同沉积条件对沉积结果的影响,发现采用交流沉积制备金属纳米线的过程中,频率和电压是影响沉积结果的关键因素．     

阳极氧化铝模板中直接直流电沉积铁纳米线

本文提出了一种在多孔阳极氧化铝(Anodic Aluminum Oxide)模板中直接直流电沉积铁纳米线的新方法.采用阶梯降压法减薄致密的阻挡层,以Al基底为阴极,铂电极为阳极.直接在制备AAO模板的装置中进行直流电沉积.用SEM对制备的AAO模板及铁纳米线进行了形貌表征,结果表明:制备的铁纳米线分布均匀,直径约为50nm,粗细与模板的孔径基本相同.本实验工艺简单,同时避开了AAO模板薄、脆、易碎的特点,从而使制备大面积的铁纳米线成为了可能.     

直流电沉积CdS纳米线的研究

在磷酸溶液中，采用二次铝阳极氧化法得到了多孔铝阳极氧化膜(AAO)．以AAO为模板，选用直流电沉积方法在孔内组装CdS半导体纳米线，溶去模板后，获得粗细均一、直径约为100nm、长度约为1．5μm的纳米线，与AAO模板的孔径一致．该方法在制备过程中，无需对AAO模板进行去除阻挡层、喷金或预镀金属等处理过程，而是直接在纳米孔内电沉积CdS，形成CdS半导体纳米线阵列．该方法工艺简单，操作方便，容易获得半导体CdS的一维纳米材料．TEM和XRD测试结果表明，CdS纳米线为六方晶型结构．对CdS纳米线的生长机理还进行了初步的分析和探讨．     

Cu/AAO复合材料的制备及表征

通过阶梯降压法,成功制备出带有铝基底的有序多孔阳极氧化铝,铝基底与有序多孔氧化铝之间的阻挡层极薄。以该模板为阴极,采用循环伏安法电化学沉积技术制备出Cu/AAO纳米复合材料。分别用场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)、X射线衍射(XRD)等测试方法对该纳米复合材料的形貌、组成和结构进行了表征和分析。结果表明,Cu纳米线在模板中填充率高,直径约为70nm,长度可达30μm,具有面心立方单晶结构。     

非晶Co及CoP纳米阵列的制备及研究

采用交流电化学沉积法,在多孔阳极氧化铝(AAO)模板孔洞中成功制备出直径50nm的Co纳米线阵列.采用透射电子显微镜(TEM)和选区电子衍射(SAED)观察了样品的微观形貌结构.结果显示,阵列中纳米线均匀有序,形状各向异性较大,其晶体结构为非晶.在沉积Co纳米线阵列的电解液中添加一定的还原剂(NaH2PO2·H2O),制备出非晶CoP纳米阵列,由TEM观察可知,阵列形貌发生变化,沉积产物为离散的纳米粒子而非纳米线.探讨了交流电沉积纳米阵列的生长机理.     

双扩散AAO模板法制备AgCl纳米线及其光催化性能

采用二次阳极氧化法,制得具有一定厚度有序性较高的阳极氧化铝(AAO)模板,并结合溶液的双扩散法制备AgCl纳米线,利用XRD、SEM和TEM等分析手段对模板和纳米线进行了表征,结果表明,用该方法制备的AgCl纳米线阵列分布均匀,取向性好,直径与AAO模板的孔径一致.通过纳米线阵列膜对罗丹明B的降解情况对其光催化活性进行了测试,结果表明,AgCl纳米线具有良好的光催化性能.     

交流电化学沉积FeCo合金纳米线阵列及其磁性能研究

采用二步阳极氧化法制备孔结构高度有序的多孔氧化铝(AAO)模板。在不同Fe2+/Co2+摩尔比的电解液中,利用交流电化学沉积,在模板孔内成功制备了FeCo合金纳米线阵列。分别采用透射电子显微镜(TEM),场发射扫描电子显微镜(FE-SEM),X射线衍射仪(XRD)和震动样品磁强计(VSM)对样品的形貌,结构及磁学性能进行了表征。结果表明,制备的FeCo合金纳米线排列有序,粗细均匀;其直径与模板孔径一致,填充率较高,且具有明显的[110]择优取向。VSM测试结果表明,不同溶液浓度下制备的FeCo合金纳米线阵列均具有良好的垂直磁各向异性,易磁化轴沿着纳米线轴线方向。随着电解液Fe2+/Co2+摩尔比的不同,可在一定范围内对FeCo合金纳米线阵列的磁性进行调控,并对其原因进行了讨论。     

SmCo纳米线阵的制备及其微结构

采用二次阳极氧化法,制备出高度有序的阳极氧化铝模板(AAO模板).并以AAO模板为电极,分别用交流和直流的方法从水溶液中沉积出SmCo纳米线阵列.用原子力显微镜、场发射扫描电镜对其形貌、成分进行表征,结果表明,SmCo纳米线的线壁光滑、线径一致,约为80nm和100nm;线阵中稀土Sin的含量达16.25%(质量分数).X射线衍射分析表明该SmCo纳米线为非晶结构.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.     

新闻(英文)

正China and Greece Sign the Standardization Cooperation Agreement Witnessed by Chinese Premier Li Keqiang and Greek Prime Minister Antonis Samaras,AQSIQ Minister Zhi Shuping and ELOT Chairman and Executive Director Angelos Tolkas signed the SAC-ELOT Standardization Cooperation Agreement.The Agreement is one of the critical cooperation documents signed during Li Keqiang’s visit in Greece,encouraging China and Greece to