Tribological properties of selected PVD coatings when slid against ductile materials

In this paper, a physical vapour deposited (PVD) deposited TiB₂ coating is compared in dry sliding with commercial PVD titanium nitride (TiN), titanium aluminium nitride (TiAlN) and titanium carbonitirde (TiCN) as to frictional properties and tendency of counter material pick-up. The aim is to investigate if the superior behaviour of the TiB₂ coating experienced in severe sliding applications against aluminium alloys can be extended to other materials with a similarly poor tribological characteristics.A new tribological test for sliding contact has been used. The test configuration involves two crossed elongated cylindrical test specimens which are forced to slide axially against each other at a constant sliding speed and a gradually increasing normal load, while recording the friction. The evaluation is performed by correlating the friction history with the width, topography and composition of the sliding tracks as detected by optical and scanning electron microscopy.Coated cemented carbide (CC) test cylinders have been slid against cylinders of a Ti alloy (Ti–6Al–4V), an Al alloy (Al 7075) and Inconel 718. It was shown that the TiB₂ surface displayed superior friction and anti-sticking properties, when tested against the aluminium alloy. Against the Ti and Inconel alloys no major difference between the coatings could be found. Instead, it is concluded that the friction coefficient is determined by the plastic properties of the counter material since a complete transfer layer instantly builds up on the coating.It proved possible to estimate the friction force from the width of the sliding tracks, the Vickers hardness of the counter material and simple plastic considerations. This estimation also verifies the unexpectedly low friction of all coatings against the Ti alloy.     

Friction and wear behaviour of Thordon XL and LgSn80 in sliding against plasma-sprayed Cr2O3 coatings

This paper studies the friction and wear behaviour of two important bearing materials, Thordon XL and LgSn80, in dry and lubricated sliding vs. plasma-sprayed Cr₂O₃ coatings. As a reference, AISI 1043 steel is also studied under the same conditions. SEM, EDS and surface topography were employed to study the wear mechanisms. The results indicate that the Thordon XL/Cr₂O₃ coating pair gives the lowest dry friction coefficient (0.16) under a normal load of 45.3 N (pressure 0.453 MPa) at a velocity of 1 m/s. The dry friction coefficient of Thordon XL/Cr₂O₃ coating increases to 0.38 under a normal load of 88.5 N (pressure 0.885 MPa). The dry friction coefficients of the LgSn80/Cr₂O₃ coating are in the range of 0.31–0.46. Secondly, both dry wear rate under low normal load (45.3 N) and lubricated wear rate under a load of 680 N for Thordon XL are lower than those of LgSn80 in sliding against plasma-sprayed Cr₂O₃ coatings at a speed of 1 m/s. However, under a normal load of 88.5 N the dry wear rate of Thordon XL is much higher than that of LgSn80. Thirdly, a high viscosity lubricant (SAE 140) leads to lower wear for Thordon XL and LgSn80 than a low viscosity lubricant (SAE 30). Finally, the dominating wear mechanism for Thordon XL is shear fracture when against the plasma-sprayed Cr₂O₃ ceramic coating. For LgSn80 against plasma-sprayed Cr₂O₃ ceramic coating, abrasive wear is the governing failure mechanism.     

Friction and wear properties of lead-free aluminum alloy bearing material with molybdenum disulfide layer by a reciprocating test

Friction and wear behavior of Al–Sn–Si alloy with MoS₂ layer under lubricated condition was investigated by a reciprocating friction tester. It became clear that the Al–Sn–Si alloy with MoS₂ layer showed about 70% lower friction and about 1/10 lower wear depth compared to the Al–Sn–Si alloy. The worn surfaces of the Al–Sn–Si alloy with MoS₂ layer were observed and analyzed by a SEM, a TEM and an EDX. It indicated that the sliding surface of the counterface had larger area of Mo than the area of Al which was transferred from the Al–Sn–Si alloy with MoS₂ layer by sliding, resulting in low friction and high wear resistance.     

Tribological behaviour of steel‐alumina sliding pairs under boundary lubrication conditions

The tribological behaviour of oil‐lubricated steel‐alumina sliding pairs was investigated using a ball‐on‐disc tribometer at room temperature. Commercial bearing balls of 10 mm diameter were mated to 99.7% Al₂O₃ discs, and additive‐free mineral oil was fed into the contact area. The sliding speed and the applied normal load were varied, and the initial surface roughness of the Al₂O₃ disc was altered using different polishing and grinding procedures. The results showed that the surface roughness of the ceramic discs dominated the tribological behaviour under the given experimental conditions. The sliding speed as well as the normal load showed less effect on the friction behaviour, but the amount of wear depended strongly on the normal load. From the results it was concluded that improvement of the surface roughness and optimised surface machining of the ceramic material can be essential for improving the tribological performance for boundary‐lubricated steel‐ceramic sliding pairs.     

Wear mechanisms of K2Ti4O9 whiskers reinforced Al20Si aluminum matrix composites with lubrication of water and tetradecane

The tribological properties of K₂Ti₄O₉ whisker reinforced Al20Si aluminum matrix composites were investigated in a mode of low amplitude reciprocal sliding. The ball-on-disk tests were performed at applied loads of 20–100 N and sliding velocity of 0.09 m s⁻¹. The water lubricated composites demonstrated higher wear resistance and friction coefficient than the tetradecane lubricated composites did. The main wear mechanism is microgrooving at low applied loads and tribochemical wear at high applied loads for the pairs lubricated with water, microgrooving at all test loads for the pairs lubricated with tetradecane.     

Deposition of duplex Al2O3/TiN coatings on aluminum alloys for tribological applications using a combined microplasma oxidation (MPO) and arc ion plating (AIP)

Microplasma oxidation (MPO) has recently been studied as a cost-effective plasma electrolytic process to provide thick and hard ceramic coatings with excellent surface load-bearing capacity on aluminum alloys. However, for sliding wear applications, such ceramic coatings often exhibit relatively high friction coefficients against many counterface materials. Although coatings deposited by physical vapour deposition (PVD) techniques such as TiN coatings are well known for providing surfaces with a high hardness, in practice they often exhibit poor performance under mechanical loading, since the coatings are usually too thin to protect the substrate from the contact conditions. In this paper, these challenges were overcome by a duplex process of microplasma oxidation and arc ion plating (AIP), in which an alumina layer Al₂O₃ was deposited on an Al alloy substrate (using MPO as a pre-treatment process) for load support, and a TiN hard coatings were deposited (using AIP) on top of the Al₂O₃ layer for low friction coefficient. Microhardness measurements, pin-on-disc sliding wear tests, and antiwear tests using a Timken tester were performed to evaluate the mechanical and tribological properties. Scanning electron microscopy (SEM) was used to observe coating morphology, and to examine wear scars from pin-on-disc test. The research demonstrates that a hard and uniform TiN coating, with good adhesion and a low coefficient of friction, can successfully be deposited on top of an alumina intermediate layer to provide excellent load support. The investigations indicate that a duplex combination of MPO coating and TiN PVD coating represents a promising technique for surface modification of Al alloys for heavy surface load bearing application.     

Influence of Sliding Speed on the Tribological Characteristics of Si3N4-hBN Ceramic Materials

The influence of sliding speed on the unlubricated tribological behaviors of silicon nitride–boron nitride (Si₃N₄-hBN) composites was investigated with two modes in air by a pin-on-disc tribometer. Using the upper disc–on–bottom pin test mode, as the sliding speed increased, the friction coefficient of the sliding pairs showed an upward trend; for example, from 0.18 at the sliding speed of 0.40 m/s to 0.54 at the sliding speed of 1.31 m/s for the Si₃N₄/Si₃N₄–20% hBN pair. The surface analysis indicated that a tribochemical film consisting of SiO₂ and H₃BO₃ formed on the wear surfaces of the Si3N4/Si3N4–20% hBN sliding pair at sliding speeds of 0.40 and 0.66 m/s. Moreover, the formation of this film lubricated the wear surfaces. At the sliding speed of 1.31 m/s, no tribochemical film formed on the wear surfaces, most likely due to the increase in surface temperature. In the upper pin–on–bottom disc test mode, the wear mechanism was dominated by abrasive wear, and no tribochemical products could be detected on the wear surfaces. The increase in sliding speed weakened the degree of abrasive wear, leading to a decrease in the friction coefficients.     

The Use of D-optimal Design for Modeling and Analyzing the Tribological Characteristics of Journal Bearing Materials Lubricated by Nano-Based Biolubricants

Response surface methodology (RSM) based on a D-optimal design was employed to investigate the tribological characteristics of journal bearing materials such as brass, bronze, and copper lubricated by a biolubricant, chemically modified rapeseed oil (CMRO). The wear and friction performance were observed for the bearing materials tested with TiO₂, WS₂, and CuO nanoadditives dispersed in the CMRO. The tests were performed by selecting sliding speed and load as numerical factors and nano-based biolubricant/bearing materials as the categorical factor to evaluate the tribological characteristics such as the coefficient of friction (COF) and specific wear rate. The results showed that RSM based on a D-optimal design was instrumental in the selection of suitable journal bearing materials for a typical system, especially one lubricated by nano-based biolubricant. At a sliding speed of 2.0 m/s and load of 100 N, the bronze bearing material with CMRO containing CuO nanoparticles had the lowest COF and wear rate. In addition, scanning electron microscopy (SEM) examination of the worn bearing surfaces showed that the bronze bearing material lubricated with CMRO containing CuO nanoadditive is smoother than copper/brass bearing material.     

Effect of TiB2 particles on sliding wear behaviour of Al–4Cu alloy

Dry sliding wear of Al–4Cu–xTiB₂ (x = 0, 2.5, 5, 7.5 and 10 wt.%) in situ composites have been studied in the peak-aged condition using a pin-on-disc wear testing machine at different loads. The composites were prepared by the reaction of a mixture of K₂TiF₆ and KBF₄ salts with molten alloy. The results indicate that TiB₂ particles markedly improve the wear performance of the Al–4Cu alloy. The wear resistance increases with increase in the amount of TiB₂. The load bearing capacity of the alloy during wear increases in presence of TiB₂ particles. Study of the wear surfaces and debris of both alloy and composites using the scanning electron microscope suggests that the improvement in wear resistance is mainly due to the formation of finer debris.     

Dry and oil-lubricated sliding wear of Si<Subscript>3</Subscript>N<Subscript>4</Subscript> and Si<Subscript>3</Subscript>N<Subscript>4</Subscript>/BN fibrous monoliths

A high-temperature ball-on-flat tribometer was used to investigate dry and oil-lubricated friction and wear of sintered Si₃N₄ and Si₃N₄/hexagonal boron nitride (H-BN) fibrous monoliths. The friction coefficients of base Si₃N₄ flats sliding against Si₃N₄ balls were in the range of 0.6–0.8 for dry and 0.03–0.15 for lubricated sliding, and the average wear rates of Si₃N₄ were 10^–5 mm³ N^–1 m^–1 for dry sliding and 10^–10–10^–8 mm³ N ^–1m^–1 for lubricated sliding. The friction coefficients of Si₃N₄ balls against composite fibrous monoliths were 0.7 for dry sliding and 0.01–0.08 for lubricated sliding. The average specific wear rates of the pairs were of the same order as those measured for the conventional Si₃N₄ pairs. However, the fibrous monoliths, in combination with sprayed dry boron nitride, resulted in reduction in the lubricated friction coefficients of the test pairs and significant reduction in their wear rates. The most striking result of this study was that the coefficients of friction of the Si₃N₄/H-BN fibrous monolith test pair were 70–80 lower than those of either roughened or polished Si₃N₄ when tests were performed under oil-lubricated sliding conditions over long distances (up to 5000 m). The results indicated that Si₃N₄/H-BN fibrous monoliths have good wear resistance and can be used to reduce friction under lubricated sliding conditions.     

Wear characteristic of in situ synthetic TiB2 particulate-reinforced Al matrix composite formed by laser cladding

In order to improve the wear resistance of an aluminum alloy, an in situ synthesized TiB₂ particulate-reinforced metal matrix composite coating was formed on a 2024 aluminum alloy by laser cladding with a powder mixture of Fe-coated boron, Ti and Al was successfully achieved using a 3-kW CW CO₂ laser. The chemical composition, microstructure and phase structure of the composite clad coating were analyzed by energy dispersive X-ray spectroscopy (EDX), SEM, TEM and XRD. The nanohardness and the elastic modulus of the phases of the coating have been examined. The dry sliding wear behaviour of the coating was investigated using a pin-on-ring machine under four loads, namely 8.9, 17.8, 26.7, and 35.6 N. It has been found that the wear characteristics of cladding were completely dependent on the content and morphology of the TiB₂ particulate and intermetallic in the microstructure and the applied load. At the lowest load (8.9 N), with increasing content of TiB₂ particulate and intermetallic, the wear weight loss of the laser cladding was decreased. At higher loads (17.8, 26.7, and 35.5 N), the 2024 Al alloy exhibited superior wear resistance to the particle-reinforced metal matrix composite cladding.     

矿物质润滑油添加剂对钢/铝锡合金摩擦副摩擦学性能的影响

利用销盘式磨损试验机研究了一种矿物质润滑油添加剂对钢/铝锡合金摩擦副摩擦学性能的影响,并考察了这种添加剂对实际工况下铝锡合金轴瓦的作用效果。采用AFM、SEM/EDS等仪器对摩擦副表面进行了分析。结果表明,矿物质添加剂在低载荷比高载荷条件下的减摩抗磨效果明显;试验时间越长,添加剂的作用越充分,圆盘表面的Al-Sn共晶体的分布越分散,减摩效果越明显;添加剂降低了摩擦表面的粗糙度,显著地提高了摩擦副的减摩抗磨性能,延长了使用寿命;添加剂作用后的摩擦表面发现了少量的Fe元素,并发现个别添加剂粒子和磨损粒子在铝锡合金表面的镶嵌和沉积,添加剂提高了其承载能力。     

Effects of anti-wear additives on friction and wear properties of Cr2O3 coating

The effects of some anti-wear additives on the friction and wear behaviour of plasma-sprayed Cr₂O₃ coating were investigated using a block-on-ring tester at ambient conditions. The results show that zinc dialkyldithiophosphate (ZDDP), tricesyl phosphate (TCP) and tributyl phosphate (TBP) significantly reduce the wear of Cr₂O₃ coating lubricated by paraffin oil. Additive concentrations as well as sliding time have great influence on the wear. The friction coefficient varies slightly with test conditions. The analysis by XPS of worn surfaces indicates that the wear resistance of these additives is due to the formation of tribochemical reaction films by reacting with Cr₂O₃ coatings.     

Improvement of the Oxidation and Wear Resistance of Pure Ti by Laser-Cladding Ti<Subscript>3</Subscript>Al Coating at Elevated Temperature

Ti₃Al coating was in situ synthesized successfully on pure Ti substrate by laser-cladding technology using aluminum powder as the precursor. The composition and microstructure of the prepared coating were analyzed by transmission electron microscopy, scanning electron microscopy (SEM), and X-ray diffraction technique. Thermal gravimetric analysis was used to evaluate the high-temperature oxidation resistance of the Ti₃Al coating. The friction and wear behavior was tested through sliding against Si₃N₄ ball at elevated temperature of 20, 100, 300, and 500°C. The morphologies of the worn surfaces and wear debris were also analyzed by SEM and three-dimensional non-contact surface mapping. The results show that the Ti₃Al coating with high microhardness, high-temperature oxidation resistance, and high temperature wear resistance. The pure Ti substrate is dominated by severe adhesion wear, abrasive wear, fracture, and severe plastic deformation at lower temperature, and severe adhesion wear, abrasive wear, plastic deformation, oxidation, and nitriding wear at higher temperature, whereas the Ti₃Al coating experiences only moderate abrasive and adhesive wear when sliding against the Si₃N₄ ceramic ball counterpart. In addition, the wear debris of the laser-cladding Ti₃Al coating sliding and Si₃N₄ friction pairs are much smaller than that of pure Ti substrate and Si₃N₄ friction pairs at elevated temperature.     

Ionic liquid lubrication of electrodeposited nickel–Si3N4 composite coatings

Nano-Si₃N₄ particles were electrodeposited with nickel on copper substrate from a Ni bath. The friction and wear properties of the Ni/Si₃N₄ composite coating were evaluated while being lubricated with several various oils using a ball-on-disk sliding tester. The morphologies of the worn surfaces were observed using a scanning electron microscope. The chemical states of several typical elements on the worn surfaces were examined by means of X-ray photoelectron spectroscopy (XPS). Results indicated that the electrodeposited Ni/Si₃N₄ composition coating had excellent tribological properties while being lubricated with the ionic liquid. This was partly attributed to the high hardness of the electrodeposited nickel composite coating containing nano-sized Si₃N₄ and the tribochemical reaction between the lubricant and the sliding surface.     

Sliding wear behaviour of T6 treated A356–TiB2 in-situ composites

Dry sliding wear behaviour of A356–TiB₂ composites in T6 condition was tested using a pin-on-disc wear testing machine. The composites were prepared by the reaction of a mixture of K₂TiF₆ and KBF₄ salts with molten alloy. The wear tests were conducted at normal loads of 19.6–78.4 N and a sliding speed of 1 ms^?1. A detailed SEM study of wear surface and debris was carried out to substantiate the wear results. The results indicate that wear rate of the composites is a strong function of TiB₂ content rather than overall hardness of the composite. The role of Si and TiB₂ particles towards the overall mechanism has been discussed.     

Tribological Behavior of Composites Based on ZA-27 Alloy Reinforced with Graphite Particles

The objective of this investigation is to assess the influence of graphite reinforcement on tribological behavior of ZA-27 alloy. The composite with 2 wt% of graphite particles was produced by the compocasting procedure. Tribological properties of unreinforced alloy and composite were studied, using block-on-disk tribometer, under dry and lubricated sliding conditions at different specific loads and sliding speeds. The worn surfaces of the samples were examined by the scanning electron microscopy (SEM). The obtained results revealed that ZA-27/graphite composite specimens exhibited significantly lower wear rate and coefficient of friction than the matrix alloy specimens in all the combinations of applied loads (F _n ) and sliding speeds (v) in dry and lubricated tests. The positive tribological effects of graphite reinforcement of ZA-27 in dry sliding tests were provided by the tribo-induced graphite film on the contact surface of composite. In test conditions, characterized by the small graphite content and modest sliding speeds and applied loads, nonuniform tribo-induced graphite films were formed leading to the increase of the friction coefficient and wear rate, with increase of the sliding speed and applied load. In conditions of lubricated sliding, the very fine graphite particles formed in the contact interface mix with the lubricating oil forming the emulsion with improved tribological characteristics. Smeared graphite decreased the negative influence of F _n on tribological response of composites, what is manifested by the mild regime of the boundary lubrication, as well as by realization of the mixed lubrication at lower values of the v/F _n ratio, with respect to the matrix alloy.     

Reciprocating Sliding Wear Performance of Hard Coating on Modified Titanium Alloy Surfaces

The high strength, low weight, and outstanding corrosion resistance properties possessed by titanium alloys have led to a wide range of successful applications in aerospace, automotive, and chemical industries and in power generation. Titanium alloys are characterized by poor wear resistance properties and their utilization has been excessive in nontribological applications. Surface texturing is a well-known and effective means of surface modification to improve the tribological properties of sliding surfaces. In the present work, modification of titanium alloy surfaces (Ti6Al4V) was done by lapping and laser surface texturing. The wear-resistant coating, AlCrN, was applied over the modified titanium alloy surfaces, with and without a chromium interlayer. Linear reciprocating sliding wear tests were performed with ball-on-flat contact geometry to evaluate the tribological performance of the coated alloy. The tests were performed under different normal loads for a period of 105 cycles at a frequency of 5 Hz. The friction force between the contact pair and displacement of the ball were simultaneously observed using a force transducer and laser displacement sensor. Optical microscopy was used to quantify the wear volume by measuring the wear scar diameter on both the specimen and the counterbody. Scanning electron microscopy (SEM) was employed to study the morphology of the wear scar. The characteristic behavior of the AlCrN coating such as bonding strength, wear volume, wear rate, and coefficient of friction with the chromium interlayer was evaluated and compared with the coating directly applied over the substrate. The coating on the textured surface, with the chromium interlayer showed better tribological performance.     

Relaxation capacity and cracking resistance of nitrous coating produced by electron-beam facing of 0.6C-24Cr-0.7N-16Mn steel powder during wear by hard abrasive under heavy loads

Specific features of the topography of friction tracks formed during the sliding of a WCo6 ball over an austenitic nitrous coating at various velocities of sliding under various loads using the ball-on-disc arrangement are studied and compared with those for the WCo6 ball-110Mn13 steel pair. It has been found that the wear resistance of nitrous austenite is due to its capacity to relax frictional stresses. The correlation between the H ₃/E ₂ parameter of the friction surface and the wear rate has been shown.     

Friction and wear properties of Babbitt alloy 16-16-2 under sea water environment

The tribological behaviors of Babbitt alloy 16-16-2 sliding against aluminum bronze ZCuAl9Mn2 lubricated by sea water were systematically investigated in this paper. The results indicated that the friction coefficient decreased as the load increased to 30 N and then remained at a steady level at high loads, but decreased with increase in sliding speed. The wear rate increased with load, but decreased with sliding speed. The formation of basic lead carbonate Pb₃(OH)₂(CO₃)₂ during the sliding process played a critical role in the remaining low friction coefficient in sea water.