共查询到18条相似文献,搜索用时 109 毫秒
1.
目的 针对低温条件下东北地区施工特点,研究了在不掺防冻剂的情况下,不同掺合料对C30幼龄期混凝土孔径分布的影响.方法:采用压汞法测试了在恒低温一次冻结和自然变低温多次冻结养护情况下幼龄期混凝土的孔径分布情况.结论:掺合料可以改善低温混凝土的内部结构,减少多害孔和有害孔的比例,提高少害孔和无害孔的比例;混凝土在恒低温-10℃养护条件下较之变低温-15℃~5℃养护条件下有害孔和多害孔所占比例高,少害孔和无害孔所占比例低. 相似文献
2.
3.
4.
高温影响下花岗岩孔径分布的分形结构及模型 总被引:1,自引:0,他引:1
温度是影响岩石物理性质的重要因素,为了探究温度对岩石孔径分布的影响规律,利用压汞法测试25 ℃~1 200 ℃高温热处理后花岗岩样品的孔隙特征,并研究了不同高温影响下岩石孔隙的分形结构和孔隙率演化模型。结果表明:(1) 随着温度的升高,岩石孔隙率呈指数增加,500 ℃~800 ℃是岩石孔隙结构变化的阈值温度区间,500 ℃之前孔隙率增长较缓慢,增长幅度约50%,之后孔隙率大幅增加3~5倍;(2) 温度升高所导致的岩石新孔隙以孔径1~10 μm的中孔为主,低于500 ℃时中孔占15%左右,而后稳步上升,800 ℃时大幅增加至28.24%,1 000 ℃以后又增至40%以上,体积增长了11.8倍,这将导致岩石防渗阻渗能力大大减弱;(3) 各温度下岩石孔隙分布均具有良好的统计分形特性,孔隙分形维数在2.99~3.00范围,随温度升高,分形维数降低,且温度越高,降低幅度越大,表明孔隙均匀性增加;(4) 基于理想Menger海绵的Friesen模型预测各孔径下累计孔隙率演化误差较大,而张季如和陶高梁模型对不同高温岩石孔径分布具有良好的预测精度。研究结果将为高放核废料深层地下存储、地热开发等高温岩石工程设计及施工提供科学依据。 相似文献
5.
6.
7.
硅粉水泥石中微孔孔径分布及其对强度的影响 总被引:6,自引:0,他引:6
采用X射线小角度散射(SAXS)技术,对硅粉水泥石中微孔孔径分布(孔半径小于50nm)进行了实验研究,并讨论了孔径分布对强度的影响.研究表明:所测硅粉水泥石的孔径均呈多峰分布,其平均孔半径约在4.5~9.0nm,最可几孔半径约在4.0~6.5nm;硅粉含量、水灰比对孔径分布有显著影响,随着硅粉含量的增加以及水灰比的减小,孔径分布向小孔方向移动;孔径分布与抗压强度有较好的相关性,而孔径分布(孔半径小于50nm)与抗折强度之间不存在明显的相关性. 相似文献
8.
强度是混凝土的一个最主要的力学性能指标,文中讨论了混凝土孔结构对混凝土强度的影响规律.通过概述孔结构与强度之间的关系,说明了混凝土材料孔结构的两个主要方面:孔隙率与孔径分布对混凝土强度的影响.国内外学者的强度与孔结构的关系模型都是在某一养护条件下获得的,其模型的适用范围存在着限制.孔隙率及孔径分布与Griffith脆性断裂理论结合,可以较好的反映出孔结构与抗拉强度的关系,但是对其相关参数的取值,还存在着较大的争议,且并未考虑骨料,模型的应用还须符合相关假定. 相似文献
9.
土的初始剪切模量G_0是地震、爆破响应中一个非常重要的土动力学参数,对预测地表沉降、土工建筑物周围土体变形等具有重要作用。黄土在中国及世界各地分布广泛,且现场常处于非饱和状态。对非饱和黄土的压实试样进行了吸力控制的共振柱试验以及压汞试验,研究非饱和黄土初始剪切模量G_0与孔径分布的关系。试验表明:干湿循环过程中,试样的G_0随吸力的增大而增大,再随吸力的减小而减小。主要原因是试样内孔隙密度最大的孔径大小随吸力的增大而减小,试样内大孔隙减少,小孔隙增多,导致毛细水所占比例增加,土颗粒接触更加紧密。同一吸力作用下,湿润段试样的小孔隙比例比干燥段大,故毛细水作用更显著,从而湿润段试样的G_0大于干燥段。 相似文献
10.
11.
Jiangfeng Liu Shuaibing Song Xulou Cao Qingbin Meng Hai Pu Yangguang Wang Jianfeng Liu 《岩石力学与岩土工程学报(英文版)》2020,12(2):403-413
Gaomiaozi(GMZ)bentonite is a potential buffer/backfill material for a deep geological disposal of highlevel radioactive waste.It has a wide pore size distribution(PSD)with sizes ranging from several nanometers to more than one hundred microns.Thus,properly characterizing the pore structures of GMZ bentonite is a challenging issue.In this study,pressure-controlled porosimetry(PCP),ratecontrolled porosimetry(RCP),and scanning electron microscopy(SEM)were used to investigate the PSD of GMZ bentonite,The results indicate that each method has its limitation,and a combined use of PCP and RCP is suitable to obtain the full-scale PSD of GMZ bentonite.Moreover,we also compared the full-scale PSD with nuclear magnetic resonance(NMR)result.It is found that there is no significant difference in the range of PSD characterization between NMR and mercury intrusion method(PCP and RCP).However,in a ce rtain range,the detection accuracy of NMR is higher than that of mercury injection method.Finally,permeability prediction based on PCP and SEM data was conducted,and both of the two methods were found to be able to predict the permeability.The combined method is effective to obtain the full-scale PSD of GMZ bentonite,which is the key to estimation of the sealing ability of bentonite buffer. 相似文献
12.
Cheng Q. Ng C. W. W. Zhou C. Tang C. S. 《Bulletin of Engineering Geology and the Environment》2019,78(7):5055-5065
Bulletin of Engineering Geology and the Environment - Pore size distribution (PSD), which is usually measured using mercury intrusion porosimetry (MIP) tests, is often used to predict the water... 相似文献
13.
土-水特征曲线(SWCC)描述了含水率和基质吸力的关系,并在一定程度上反映了孔隙组成,然而生活垃圾具有大孔隙特性,采用常规的压力板仪试验难以准确获得大孔隙对应的低基质吸力范围内的数据点。通过压力板仪试验确定小孔隙对应的数据点,通过水分穿透试验,基于Poiseuille定律和Young-Laplace方程,对大孔隙对应的数据点进行补充,之后,基于Van Genuchten方程,提出具有双峰孔隙分布特征垃圾的SWCC模型,进一步分析得到垃圾的孔径分布规律。结果表明,改进的SWCC方程可更好反映垃圾持水特性及孔径特征;垃圾饱和含水率和残余含水率较高,浅层、中层、深层垃圾的田间持水率分别为38.5%,42.2%和45.8%,对应的基质吸力约为3~8 k Pa,随着埋深和龄期的增加,垃圾的有效含水率区间和给水度减小;以基质吸力1 k Pa对应的孔径为界限,垃圾中孔隙可分为大小两组,孔径概率密度呈双峰分布,随着埋深和龄期的增加,垃圾的大孔隙占比减小,大孔隙平均孔径减小,小孔隙占比增加,小孔隙平均孔径减小。 相似文献
14.
光催化技术及其在混凝土中的应用 总被引:4,自引:0,他引:4
二氧化钵光催化氧化技术是一种节能、高效的绿色环保技术。近年来已成为光化学领域和环保领域中的研究热点之一。本文介绍了半导体光催化原理、具有光催化性能混凝土材料的应用,提出了具有光催化性能的混凝土材料存在的问题及发展趋势。 相似文献
15.
介绍了粉煤灰的物理、化学特性,就其在混凝土中的合理应用进行了阐述,以充分利用其环保和经济价值,为粉煤灰的合理、广泛应用积累了经验。 相似文献
16.
The cement production industry is one of the most energy and raw materials consuming one. Over the last years a great effort is performed in order to substitute clinker for less energy demanding materials. Nevertheless, construction industry needs durable materials with improved properties. Limestone is being used in blended cements widely. The most important parameter that affects all the properties of cement paste is its pore structure. In this study, four different limestone cements were produced and their pore structure was determined by means of mercury intrusion porosimetry (MIP) and nuclear magnetic resonance (NMR) cryoporometry. The conclusion of the study was that limestone addition affects the pore structure of the cement paste by increasing linearly the size of capillary pores from 20 nm to 40 nm when the maximum amount (35%) of limestone that is allowed by EN 197-1 is used. On the other hand the threshold diameter decreases exponentially and it is evident that limestone hardened cement pastes have many pores of the same size due to the filling effect that minerals additives have. Furthermore, limestone decreases the size of gel pores which is related to higher hydration rates. Hence, the use of limestone in cement produces a material that is structurally adequate to be used in construction. 相似文献
17.