Phase transformation in semi-transparent TiO2 films irradiated with CO2 laser

Anatase (TiO₂) thin films were obtained by immersion of glass plates into a titanium sol-gel precursor followed by calcination at 450 °C for 3 h. The Raman results for the CO₂ laser irradiated TiO₂ films show that laser radiation is able to promote favorable changes of anatase phase in anatase/rutile mixtures. Nevertheless, the transformation process level depends on laser characteristics and scan speed of the radiation treatment.     

Non-melting annealing of silicon by CO2 laser

In this work we investigate CO₂ laser annealing at millisecond time scale for the fabrication of Ultra Shallow Junctions, able to fulfill the requirements imposed for sub-45 nm CMOS nodes. Silicon samples doped with Boron using BF₃ plasma implantation technique at low energy (0.4 and 0.6 keV) were used to ensure ultra shallow as implanted boron concentration profiles. Our aim is to achieve high electrical activation level of the dopant, while maintaining the Boron concentration profile as immobile as possible. Samples have been irradiated at a variety of annealing conditions regarding the duration of the irradiation and the power density; however, in every case the peak surface temperature was kept in the range of 1080-1320 °C. Sheet resistance measurements indicate significant enhancement in the activation levels, while chemical characterization by means of SIMS, shows very limited movement of the dopant concentration profile, especially for short pulse duration conditions.     

Electrochemical reduction of CO2 by Cu2O-catalyzed carbon clothes

Cu₂O cubes with average edge lengths of 640 nm were prepared by a chemical reduction approach. The as-synthesized Cu₂O particles were deposited on carbon clothes for electrochemical characterizations in cyclic voltammetry (CV) and potentiostatic measurements. In 0.5 M NaOH electrolytes saturated with N₂ or CO₂, both the Cu₂O and carbon clothes were stable at the potential range of 0 to − 1.7 V. Comparisons in the current responses from the CV and potentiostatic measurements suggested the Cu₂O with notable catalytic abilities for the CO₂ reduction. The mass activity was estimated at 0.94 mA/mg. Chemical analysis from gas chromatography confirmed the methanol to be the predominant product.     

Spectroscopic investigation on phase transitions for Ge2Sb2Te5 in a wide photon energy and high temperature region

We investigated the electronic properties of phase-change material Ge₂Sb₂Te₅ (GST) films using spectroscopic ellipsometry in a wide photon energy and high temperature region. Apart from the charge carrier response, the totality of optical conductivity spectra for three phases of GST films, i.e., amorphous (AM), face-centered-cubic (FCC), and hexagonal (HEX), is quite similar, composed of two interband transitions in visible and UV regions. From optical analysis in a wide photon energy region up to 8.7 eV, we found that the intensity as well as the position of the interband transition in the visible region changes significantly as the phase of GST films turns from the amorphous to the crystalline phase, which is consistent with previous theoretical studies. In high temperature measurements above room temperature for the three phases of GST films, we found that the change of optical response for the AM phase of GST film occurs abruptly through two successive phase transitions near 150 °C and 270 °C, while the optical spectra of the FCC phase shows a change only near 270 °C. In contrast to the two above-mentioned cases, a slight change in optical spectra is observed for the HEX phase with the increasing temperature. From the measured optical spectra, we derived the temperature dependence of optical bandgap for the three phases, which are closely correlated to the change of the transport property for the GST films.     

Interaction of CO2 laser-modified nylon with osteoblast cells in relation to wettability

It has been amply demonstrated previously that CO₂ lasers hold the ability to surface modify various polymers. In addition, it has been observed that these surface enhancements can augment the biomimetic nature of the laser irradiated materials. This research has employed a CO₂ laser marker to produce trench and hatch topographical patterns with peak heights of around 1 μm on the surface of nylon 6,6. The patterns generated have been analysed using white light interferometry, optical microscopy and X-ray photoelectron spectroscopy was employed to determine the surface oxygen content. Contact angle measurements were used to characterize each sample in terms of wettability. Generally, it was seen that as a result of laser processing the contact angle, surface roughness and surface oxygen content increased whilst the apparent polar and total surface energies decreased. The increase in contact angle and reduction in surface energy components was found to be on account of a mixed intermediate state wetting regime owing to the change in roughness due to the induced topographical patterns. To determine the biomimetic nature of the modified and as-received control samples each one was seeded with 2 × 10⁴ cells/ml normal human osteoblast cells and observed after periods of 24 h and 4 days using optical microscopy and SEM to determine mean cell cover densities and variations in cell morphology. In addition, a haemocytometer was used to show that the cell count for the laser patterned samples had increased by up to a factor of 1.5 compared to the as-received control sample after 4 days of incubation. Significantly, it was determined that all laser-induced patterns gave rise to better cell response in comparison to the as-received control sample studied due to increased preferential cell growth on those surfaces with increased surface roughness.     

Oil mass fraction measurement of CO2/PAG mixture

In this study, a method of using a capacitance sensor was investigated as a means to measure the mass fraction of a type of PAG oil flowing with CO₂ in a transcritical cycle. The test facility equipped with the capacitance sensor was fabricated to establish and maintain a known oil mass fraction and to measure the capacitance of the CO₂/oil mixture. By using this facility, the relationship among three parameters (reduced CO₂ density (CO₂ density divided by the critical density of CO₂), oil mass fraction, and relative dielectric constant of the CO₂/PAG oil mixture) was developed. For the range of oil mass fraction 0–0.07, the error of new measurement method was within 0.005 for a wide range of pressures and temperatures tested. This study established the method of measuring the oil mass fraction continuously in the transcritical CO₂ cycle without affecting the cycle performance. Through this method, the effect of oil mass fraction on the characteristics of the oil circulation behavior and the performance of the transcritical CO₂ cycle can be investigated.     

Efficiency of the indicated process of CO2-compressors

The compressor of a refrigerant compression process is the component with the major influence on the efficiency and reliability of the entire system. Due to the fluid properties of carbon dioxide (CO₂), the pressure ratio of the refrigeration process with CO₂ as the working fluid is, in relation to common refrigeration processes, rather low while the pressure difference is extremely high. From experimental and theoretical considerations it becomes obvious that at these conditions a high volumetric and energetic efficiency of the compressor may be achieved if its design is appropriate. In this paper, the effects on the efficiency of the indicated compression process of a CO₂-compressor are discussed and evaluated and a promising design concept for an efficient CO₂-compressor is derived.     

CO2养护混凝土技术研究进展

CO_2养护混凝土技术是将CO_2与新拌混凝土在成型后接触,使CO_2与水泥熟料矿物间发生化学反应,进而使得新拌水泥混凝土在很短的时间内凝结硬化的养护技术。它不仅可以获得性能更好的混凝土,还可以合理利用CO_2并且节能减排,是一项有前景的可持续发展技术。综述了CO_2养护混凝土的反应机理、影响养护过程的关键因素、CO_2养护混凝土对微观结构以及耐久性的影响、后续水养护等方面的研究进展,并对CO_2养护混凝土技术的未来发展进行了展望。     

硅胶负载离子液体的CO2吸附性能影响因素研究

采用浸渍法将两种离子液体负载在A型和B型硅胶上,研究了硅胶种类和活化温度、离子液体种类和负载量、吸附剂孔径分布(PSD)等对CO2吸附效率的影响。结果表明,制得的吸附剂均具有发达的微孔结构,在0.4~0.8nm连续分布;A型硅胶经500℃活化,且[bmim]PF6用量为20%(质量分数)时,负载样品具有较好的CO2吸附性能,273K和0.1 MPa时为3.68%(质量分数);载体中引入[bmim]PF6,可以协同提高负载样品的CO2吸附量和CO2/N2选择性,且吸附速率高于纯[bmim]PF6。     

基于质谱诊断的C4H8/H2等离子体状态在放电腔室的径向分布研究

利用质谱研究了不同工艺参数下C_4H_8/H_2等离子体的离子组分和能量的径向分布规律,并分析了CH片段的裂解与聚合过程。结果表明,当工作压强较低时(≤7Pa),小分子CH片段的相对密度随径向距离的增大而逐渐减小,大分子CH片段则逐渐增多;随着工作压强的增大,CH片段的相对密度达到极值所对应的径向距离逐渐增大。当射频功率一定时,小分子CH片段的相对密度随径向距离增大而减小,大分子CH片段则逐渐增多。此外,离子能量随径向距离的增大均呈现出逐渐减小的趋势。当工作压强为3Pa、射频功率为20 W时,C_4H_8/H_2等离子体中CH片段的径向分布最均匀,有利于提高辉光放电聚合物薄膜结构与组分的均匀性。     

载体Al/Si比对Cu-ZnO-ZrO2催化剂上CO2加氢合成甲醇的影响

用直接合成法制备了不同铝硅物质的量比Al-SBA-15(β)(β=n(Al)/n(Si)=0,0.02,0.03,0.05)介孔分子筛,并采用浸渍法制备了金属负载量m=35%的CZZ/Al-SBA-15(β)负载型介孔催化剂,考察了Al/Si比对负载催化剂结构和性能的影响。采用N_2吸附-脱附、X射线衍射(XRD)、H_2程序升温还原(H_2-TPR)、CO_2吸附(CO_2-TPD)、NH3吸附(NH3-TPD)和透射电子显微镜(TEM)等手段对样品进行了表征,在固定床反应器上评价了其CO_2加氢合成甲醇的催化性能。实验结果表明,CZZ/Al-SBA-15(β)具有介孔结构,Al的引入不但增加了载体表面酸性位点,同时还提高了催化剂表面铜分散度(DCu%)和铜比表面积(SCu)以及促进了Cu~+-O-Zn活性位的形成,从而大大提高了催化剂的活性。其中CZZ/Al-SBA-15(0.03)催化剂的甲醇选择性达到26%,与不掺铝的CZZ/Al-SBA-15(0)催化剂相比,甲醇选择性提高了11%,但随着掺Al量的继续增加,酸性太强,CO_2吸附能力下降,活性反而降低。     

微结构对Bi_2Sr_2Co_2O_y化合物电性能的影响

通过溶胶-凝胶法制备单相Bi2Sr2Co2Oy化合物,通过添加PEG20000和超声分散对化合物粉体微结构进行调控,采用SPS烧结得到了致密的块体.探索了微结构对Bi2Sr2Co2Oy化合物电性能的影响规律.结果表明,添加PEG20000和超声分散可以明显降低Bi2Sr2Co2Oy化合物粉体的晶粒尺寸,使烧结块体的晶粒尺寸大幅度减小,从而显著提高材料的电性能.温度为873K时,添加PEG20000并超声处理所制备样品烧结块体获得了最高ZT值0.041.     

Modulating calcium phosphate formation using CO2 laser engineering of a polymeric material

The use of simulated body fluid (SBF) is widely used as a screening technique to assess the ability of materials to promote calcium phosphate formation. This paper details the use of CO₂ laser surface treatment of nylon® 6,6 to modulate calcium phosphate formation following immersion in SBF for 14 days. Through white light interferometry (WLI) it was determined that the laser surface processing gave rise to maximum Ra and Sa parameters of 1.3 and 4.4 μm, respectively. The use of X-ray photoelectron spectroscopy (XPS) enabled a maximum increase in surface oxygen content of 5.6%at. to be identified. The laser-induced surface modifications gave rise to a modulation in the wettability characteristics such that the contact angle, θ, decreased for the whole area processed samples, as expected, and increased for the patterned samples. The increase in θ can be attributed to a transition in wetting nature to a mixed-state wetting regime. It was seen for all samples that calcium phosphate formed on each surface following 14 days. The largest increase in mass, Δg, owed to calcium phosphate formation, was brought about by the whole area processed sample irradiated with a fluence of 51 J cm^− 2. No correlation between the calcium phosphate formation and the laser patterned surface properties was determined due to the likely affect of the mixed-state wetting regime. Strong correlations between θ, the surface energy parameters and the calcium phosphate formation for the whole area processed samples allow one to realize the potential for this surface treatment technique in predicting the bone forming ability of laser processed materials.     

Applying the transcritical CO2 process to a drying heat pump

The transcritical CO₂ process fits well to the air dehumidification process observed in a heat pump dryer. Gains (respectively avoided losses) in connection with heat transfer during the air heating phase and superior compressor performance make up for the higher throttling losses of the process, resulting in an equivalent or even better coefficient of performance than the comparative R134a process.     

The photoluminescence of Ce-doped Lu4Si2O7N2 green phosphors

Cerium-doped Lu₄Si₂O₇N₂ green phosphors were synthesized by a high-temperature solid-state reaction method under nitrogen atmosphere. Compared with Ce-doped Y₄Si₂O₇N₂ phosphors, Ce-doped Lu₄Si₂O₇N₂ phosphors showed longer wavelengths of both excitation and emission, lower Stokes shift, and much stronger emission intensity. Based on the first-principles calculations of the two phosphors, the strong emission intensity originates from the large density of states. At last, the effects of Ce³⁺ concentration on photoluminescence were also examined.     

Y2O3添加量对Al2O3/ZrO2共晶陶瓷显微组织及力学性能的影响

为探索第三组元Y₂O₃添加对Al₂O₃/ZrO₂共晶陶瓷显微组织与机械性能的影响,本文利用低温度梯度的高温熔凝法制备了直径为20 mm的Al₂O₃/ZrO₂(Y₂O₃)共晶陶瓷块体,采用SEM、EDS及XRD技术对共晶陶瓷进行微结构分析,并利用维氏压痕法对其硬度和断裂韧性进行测试。SEM结果表明,凝固组织由群集的共晶团结构组成,随着Y₂O₃添加量的增加,共晶团形态由胞状转变为枝晶状,内部相间距在1~2 μm范围内变化。力学测试表明,Y₂O₃摩尔分数小于1.1%时,由于组织内部存在低硬度m-ZrO₂及微裂纹缺陷,故陶瓷硬度较低,约为(9.53±0.22 )GPa;当Y₂O₃摩尔分数为1.1%时,陶瓷硬度最大,约为(18.05±0.27)GPa;当Y₂O₃的摩尔分数大于1.1%时,由于共晶团边界区内气孔缺陷及粗大组织增多,引起陶瓷硬度值略有下降。低Y₂O₃摩尔分数添加时,陶瓷断裂韧性相对较高,约为(6.30±0.16)MPa·m^1/2,这与其内部存在大量微裂纹缺陷有关;随着Y₂O₃添加量的增加,陶瓷的微裂纹数量减少、边界区内缺陷增多,断裂韧性降低。     

超声协同微球型Bi2O2CO3降解罗丹明B的研究

Bi_2O_2CO_3是一种Bi类半导体催化剂,文章研究了它的超声催化性能。首先,采用水热法制备了微球型的Bi_2O_2CO_3,利用X射线衍射(X-ray Diffraction, XRD)、扫描电子显微镜(Scanning Electron Microscope, SEM)、紫外-可见漫反射光谱对样品的晶体结构、微观形貌、光学特性进行了表征。然后,以罗丹明B(Rh B)作为模型污染物,通过研究超声催化降解罗丹明B来评测Bi_2O_2CO_3的超声催化性能。研究了催化剂的浓度(Ccatalytic)、初始罗丹明B染料的浓度(CRhB)和超声功率(P)等实验因素对超声催化降解效率的影响。得出在Ccatalytic=3 g·L-1,CRhB=10 mg·L-1和P=400 W条件下降解罗丹明B的效率最高,其最高降解效率可以达到91.7%。     

Low temperature biomimetic synthesis of the Li2ZrO3 nanoparticles containing Li6Zr2O7 and high temperature CO2 capture

Li₂ZrO₃ nanoparticles containing Li₆Zr₂O₇ were prepared by a biomimetic soft solution route and characterized with X-ray diffraction (XRD), transmission electron microscope (TEM) and nitrogen adsorption. The results show that the tetragonal Li₂ZrO₃ nanoparticles containing monoclinic Li₆Zr₂O₇ can be obtained using this simple method. The mean diameter of the nanoparticles is approximately 90 nm and the corresponding specific surface area is 23.7 m² g^− 1. Moreover, the Li₂ZrO₃ nanoparticles obtained were thermally analyzed under a CO₂ flux to evaluate their CO₂ capture capacity at high temperature. It was found that the as-prepared Li₂ZrO₃ nanoparticles would be an effective acceptor for high temperature CO₂ capture.     

Effect of sputtering pressure and post-annealing on hydrophilicity of TiO2 thin films deposited by reactive magnetron sputtering

A series of TiO₂ thin films was deposited onto glass substrates without intentional heating or biasing by magnetron sputtering of a titanium target using Ar/O₂ reactive mixtures over a broad range of total sputtering pressures from 0.12 Pa to 2.24 Pa. Each of the film types was deposited by the threshold poisoned mode at a specific given oxygen flow rate monitored in-situ by optical emission spectroscopy. Both the sputtering pressure and thermal annealing are the key factors for the TiO₂ films to yield fast-response superhydrophilicity with a water contact angle of 5°. The mechanism of superhydrophilicity for the TiO₂ films deposited by high-pressure sputtering will be discussed based on empirical studies of X-ray diffractometry, high-resolution scanning microscopy and atomic force spectroscopy.     

Effect of pressure on the electrodeposition of nanocrystalline Ni-C in supercritical CO2 fluid

Electrodeposition of Ni in a Watt's bath at different applied pressure, and in the presence of CO₂ fluid was investigated. The reduction of carbon and its alloying into the Ni deposit was focused. The current efficiency of electrodeposition and the carbon content in the Ni deposit were found to vary with the applied pressure. The crystal structure of the resulting Ni-C film was characterized by performing X-ray diffraction. The composition of the deposit was analyzed using X-ray photoelectron spectroscopy. Transmission electron microscopy was employed for microstructure analysis. The results showed that nanocrystalline Ni-C deposit could be obtained. The grain size of the Ni-C film varied from 14 to 43 nm, depending on the deposition pressure and carbon content. A significant increase in microhardness from 450 to 720 Hv could be obtained for the Ni film electrodeposited from a bath of 15 MPa supercritical CO₂ fluid. In 1 M HCl solution, a higher open circuit potential and a lower anodic current density were found when the carbon content in the Ni deposit was increased.