Small Molecules Functionalized Zinc Oxide Interlayers for High Performance Low-Temperature Carbon-Based CsPbI2Br Perovskite Solar Cells

The charge recombination resulting from bulk defects and interfacial energy level mismatch hinders the improvement of the power conversion efficiency (PCE) and stability of carbon-based inorganic perovskite solar cells (C-IPSCs). Herein, a series of small molecules including ethylenediaminetetraacetic acid (EDTA) and its derivatives (EDTA-Na and EDTA-K) are studied to functionalize the zinc oxide (ZnO) interlayers at the SnO₂/CsPbI₂Br buried interface to boost the photovoltaic performance of low-temperature C-IPSCs. This strategy can simultaneously passivate defects in ZnO and perovskite films, adjust interfacial energy level alignment, and release interfacial tensile stress, thereby improving interfacial contact, inhibiting ion migration, alleviating charge recombination, and promoting electron transport. As a result, a maximum PCE of 13.94% with a negligible hysteresis effect is obtained, which is one of the best results reported for low-temperature CsPbI₂Br C-IPSCs so far. Moreover, the optimized devices without encapsulation demonstrate greatly improved operational stability.     

High-Efficiency Carbon-based CsPbI2Br Perovskite Solar Cells from Dual Direction Thermal Diffusion Treatment with Cadmium Halides

In recent years, carbon-based CsPbI₂Br perovskite solar cells (PSCs) have attracted more attention due to their low cost and good stability. However, the power conversion efficiency (PCE) of carbon-based CsPbI₂Br PSCs is still no more than 16%, because of the defects in CsPbI₂Br or at the interface with the electron transport layer (ETL), as well as the energy level mismatch, which lead to the loss of energy, thus limiting PCE values. Herein, a series of cadmium halides are introduced, including CdCl₂, CdBr₂ and CdI₂ for dual direction thermal diffusion treatment. Some Cd²⁺ ions thermally diffuse downward to passivate the defects inside or on the surface of SnO₂ ETL. Meanwhile, the energy level structure of SnO₂ ETL is adjusted, which is in favor of the transfer of electron carriers and blocking holes. On the other hand, part of Cd²⁺ and Cl⁻ ions thermally diffuse upward into the CsPbI₂Br lattice to passivate crystal defects. Through dual direction thermal diffusion treatment by CdCl₂, CdI₂ and CdBr₂, the performance of devices has been significantly improved, and their PCE has been increased from 13.01% of the original device to 14.47%, 14.31%, and 13.46%, respectively. According to existing reports, 14.47% is one of the highest PCE of carbon-based CsPbI₂Br PSCs with SnO₂ ETLs.     

Dual Interfacial Design for Efficient CsPbI2Br Perovskite Solar Cells with Improved Photostability

A synergic interface design is demonstrated for photostable inorganic mixed‐halide perovskite solar cells (PVSCs) by applying an amino‐functionalized polymer (PN4N) as cathode interlayer and a dopant‐free hole‐transporting polymer poly[5,5′‐bis(2‐butyloctyl)‐(2,2′‐bithiophene)‐4,4′‐dicarboxylate‐alt‐5,5′‐2,2′‐bithiophene] (PDCBT) as anode interlayer. First, the interfacial dipole formed at the cathode interface reduces the workfunction of SnO₂, while PDCBT with deeper‐lying highest occupied molecular orbital (HOMO) level provides a better energy‐level matching at the anode, leading to a significant enhancement in open‐circuit voltage (V_oc) of the PVSCs. Second, the PN4N layer can also tune the surface wetting property to promote the growth of high‐quality all‐inorganic perovskite films with larger grain size and higher crystallinity. Most importantly, both theoretical and experimental results reveal that PN4N and PDCBT can interact strongly with the perovskite crystal, which effectively passivates the electronic surface trap states and suppresses the photoinduced halide segregation of CsPbI₂Br films. Therefore, the optimized CsPbI₂Br PVSCs exhibit reduced interfacial recombination with efficiency over 16%, which is one of the highest efficiencies reported for all‐inorganic PVSCs. A high photostability with a less than 10% efficiency drop is demonstrated for the CsPbI₂Br PVSCs with dual interfacial modifications under continuous 1 sun equivalent illumination for 400 h.     

Tailoring C60 for Efficient Inorganic CsPbI2Br Perovskite Solar Cells and Modules

Although inorganic perovskite solar cells (PSCs) are promising in thermal stability, their large open-circuit voltage (V_OC) deficit and difficulty in large-area preparation still limit their development toward commercialization. The present work tailors C₆₀ via a codoping strategy to construct an efficient electron-transporting layer (ETL), leading to a significant improvement in V_OC of the inverted inorganic CsPbI₂Br PSC. Specifically, tris(pentafluorophenyl)borane (TPFPB) is introduced as a dopant to lower the lowest unoccupied molecular orbital (LUMO) level of the C₆₀ layer by forming a Lewis acidic adduct. The enlarged free energy difference provides a favorable enhancement in electron injection and thereby reduces charge recombination. Subsequently, a nonhygroscopic lithium salt (LiClO₄) is added to increase electron mobility and conductivity of the film, leading to a reduction in the device hysteresis and facilitating the fabrication of a large-area device. Finally, the as-optimized inorganic CsPbI₂Br PSCs gain a champion power conversion efficiency (PCE) of 15.19%, with a stabilized power output (SPO) of 14.21% (0.09 cm²). More importantly, this work also demonstrates a record PCE of 14.44% for large-area inorganic CsPbI₂Br PSCs (1.0 cm²) and reports the first inorganic perovskite solar module with the excellent efficiency exceeding 12% (10.92 cm²) by a self-developed quasi-curved heating method.     

Dopant-Free Polymer Hole Transport Materials for Highly Stable and Efficient CsPbI3 Perovskite Solar Cells

All-inorganic perovskite CsPbI₃ contains no volatile organic components and is a thermally stable photoactive material for wide-bandgap perovskite solar cells (PSCs); however, CsPbI₃ readily undergoes undesirable phase transitions due to the hygroscopic nature of the ionic dopants used in commonly used hole transport materials. In the current study, the popular donor material PM6 in organic solar cells is used as a hole transport layer (HTL). The benzodithiophene-based backbone-conjugated polymer requires no dopant and leads to a higher power conversion efficiency (PCE) than 2,2′,7,7′-tetrakis[N,N-di(4-methoxyphenyl)amino]-9,9′-spirobifluorene (Spiro-OMeTAD). Moreover, PM6 also shows priorities in hole mobility, hydrophobicity, cascade energy level alignment, and even defect passivation of perovskite films. With PM6 as the dopant-free HTL, the PSCs achieve a champion PCE of 18.27% with a competitive fill factor of 82.8%. Notably, the present PCE is based on the dopant-free HTL in CsPbI₃ PSCs reported thus far. The PSCs with PM6 as the HTL retain over 90% of the initial PCE stored in a glovebox filled with N₂ for 3000 h. In contrast, the PSCs with Spiro-OMeTAD as the HTL maintain ≈80% of the initial PCE under the same conditions.     

Interface Engineering for All‐Inorganic CsPbI2Br Perovskite Solar Cells with Efficiency over 14%

In this work, a SnO₂/ZnO bilayered electron transporting layer (ETL) aimed to achieve low energy loss and large open‐circuit voltage (V_oc) for high‐efficiency all‐inorganic CsPbI₂Br perovskite solar cells (PVSCs) is introduced. The high‐quality CsPbI₂Br film with regular crystal grains and full coverage can be realized on the SnO₂/ZnO surface. The higher‐lying conduction band minimum of ZnO facilitates desirable cascade energy level alignment between the perovskite and SnO₂/ZnO bilayered ETL with superior electron extraction capability, resulting in a suppressed interfacial trap‐assisted recombination with lower charge recombination rate and greater charge extraction efficiency. The as‐optimized all‐inorganic PVSC delivers a high V_oc of 1.23 V and power conversion efficiency (PCE) of 14.6%, which is one of the best efficiencies reported for the Cs‐based all‐inorganic PVSCs to date. More importantly, decent thermal stability with only 20% PCE loss is demonstrated for the SnO₂/ZnO‐based CsPbI₂Br PVSCs after being heated at 85 °C for 300 h. These findings provide important interface design insights that will be crucial to further improve the efficiency of all‐inorganic PVSCs in the future.     

Graded 2D/3D Perovskite Heterostructure for Efficient and Operationally Stable MA-Free Perovskite Solar Cells

Almost all highly efficient perovskite solar cells (PVSCs) with power conversion efficiencies (PCEs) of greater than 22% currently contain the thermally unstable methylammonium (MA) molecule. MA-free perovskites are an intrinsically more stable optoelectronic material for use in solar cells but compromise the performance of PVSCs with relatively large energy loss. Here, the open-circuit voltage (V_oc) deficit is circumvented by the incorporation of β-guanidinopropionic acid (β-GUA) molecules into an MA-free bulk perovskite, which facilitates the formation of quasi-2D structure with face-on orientation. The 2D/3D hybrid perovskites embed at the grain boundaries of the 3D bulk perovskites and are distributed through half the thickness of the film, which effectively passivates defects and minimizes energy loss of the PVSCs through reduced charge recombination rates and enhanced charge extraction efficiencies. A PCE of 22.2% (certified efficiency of 21.5%) is achieved and the operational stability of the MA-free PVSCs is improved.     

Non‐Preheating Processed Quasi‐2D Perovskites for Efficient and Stable Solar Cells

Although the hot‐casting (HC) technique is prevalent in developing preferred crystal orientation of quasi‐2D perovskite films, the difficulty of accurately controlling the thermal homogeneity of substrate is unfavorable for the reproducibility of device fabrication. Herein, a facile and effective non‐preheating (NP) film‐casting method is proposed to realize highly oriented quasi‐2D perovskite films by replacing the butylammonium (BA⁺) spacer partially with methylammonium (MA⁺) cation as (BA)_2?x(MA)_3+xPb₄I₁₃ (x = 0, 0.2, 0.4, and 0.6). At the optimal x‐value of 0.4, the resultant quasi‐2D perovskite film possesses highly orientated crystals, associated with a dense morphology and uniform grain‐size distribution. Consequently, the (BA)_1.6(MA)_3.4Pb₄I₁₃‐based solar cells yield champion efficiencies of 15.44% with NP processing and 16.29% with HC processing, respectively. As expected, the HC‐processed device shows a poor performance reproducibility compared with that of the NP film‐casting method. Moreover, the unsealed device (x = 0.4) displays a better moisture stability with respect to the x = 0 stored in a 65% ± 5% relative humility chamber.     

Dopant‐Free Hole‐Transporting Materials for Stable and Efficient Perovskite Solar Cells

Molecularly engineered novel dopant‐free hole‐transporting materials for perovskite solar cells (PSCs) combined with mixed‐perovskite (FAPbI₃)_0.85(MAPbBr₃)_0.15 (MA: CH₃NH₃⁺, FA: NH=CHNH₃⁺) that exhibit an excellent power conversion efficiency of 18.9% under AM 1.5 conditions are investigated. The mobilities of FA‐CN, and TPA‐CN are determined to be 1.2 × 10^?4 cm² V^?1 s^?1 and 1.1 × 10^?4 cm² V^?1 s^?1, respectively. Exceptional stability up to 500 h is measured with the PSC based on FA‐CN. Additionally, it is found that the maximum power output collected after 1300 h remained 65% of its initial value. This opens up new avenue for efficient and stable PSCs exploring new materials as alternatives to Spiro‐OMeTAD.     

Highly Efficient and Stable Solar Cells Based on Crystalline Oriented 2D/3D Hybrid Perovskite

Highly efficient and stable 2D/3D hybrid perovskite solar cells using 2‐thiophenemethylammonium (ThMA) as the spacer cation are successfully demonstrated. It is found that the incorporation of ThMA spacer cation into 3D perovskite, which forms a 2D/3D hybrid structure, can effectively induce the crystalline growth and orientation, passivate the trap states, and hinder the ion motion, resulting in improved carrier lifetime and reduced recombination losses. The optimized device exhibits a power conversion efficiency (PCE) of 21.49%, combined with a high V_OC of 1.16 V and a notable fill factor (FF) of 81%. More importantly, an encapsulated 2D/3D hybrid perovskite device sustains ≈99% of its initial PCE after 1680 h in the ambient atmosphere, whereas the control 3D perovskite device drops to ≈80% of the original performance. Importantly, the device stability under continuous light soaking (100 mW cm^?2) is enhanced significantly for 2D/3D perovskite device in comparison with that of the control device. These results reveal excellent photovoltaic properties and intrinsic stabilities of the 2D/3D hybrid perovskites using ThMA as the spacer cation.     

Highly Efficient 2D/3D Hybrid Perovskite Solar Cells via Low‐Pressure Vapor‐Assisted Solution Process

The fabrication of multidimensional organometallic halide perovskite via a low‐pressure vapor‐assisted solution process is demonstrated for the first time. Phenyl ethyl‐ammonium iodide (PEAI)‐doped lead iodide (PbI₂) is first spin‐coated onto the substrate and subsequently reacts with methyl‐ammonium iodide (MAI) vapor in a low‐pressure heating oven. The doping ratio of PEAI in MAI‐vapor‐treated perovskite has significant impact on the crystalline structure, surface morphology, grain size, UV–vis absorption and photoluminescence spectra, and the resultant device performance. Multiple photoluminescence spectra are observed in the perovskite film starting with high PEAI/PbI₂ ratio, which suggests the coexistence of low‐dimensional perovskite (PEA₂MA_n?1Pb_nI_3n+1) with various values of n after vapor reaction. The dimensionality of the as‐fabricated perovskite film reveals an evolution from 2D, hybrid 2D/3D to 3D structure when the doping level of PEAI/PbI₂ ratio varies from 2 to 0. Scanning electron microscopy images and Kelvin probe force microscopy mapping show that the PEAI‐containing perovskite grain is presumably formed around the MAPbI₃ perovskite grain to benefit MAPbI₃ grain growth. The device employing perovskite with PEAI/PbI₂ = 0.05 achieves a champion power conversion efficiency of 19.10% with an open‐circuit voltage of 1.08 V, a current density of 21.91 mA cm^?2, and a remarkable fill factor of 80.36%.     

Dopant-Free Organic Hole-Transporting Material for Efficient and Stable Inverted All-Inorganic and Hybrid Perovskite Solar Cells

Designing new hole-transporting materials (HTMs) with desired chemical, electrical, and electronic properties is critical to realize efficient and stable inverted perovskite solar cells (PVSCs) with a p–i–n structure. Herein, the synthesis of a novel 3D small molecule named TPE-S and its application as an HTM in PVSCs are shown. The all-inorganic inverted PVSCs made using TPE-S, processed without any dopant or post-treatment, are highly efficient and stable. Compared to control devices based on the commonly used HTM, PEDOT:PSS, devices based on TPE-S exhibit improved optoelectronic properties, more favorable interfacial energetics, and reduced recombination due to an improved trap passivation effect. As a result, the all-inorganic CsPbI₂Br PVSCs based on TPE-S demonstrate a remarkable efficiency of 15.4% along with excellent stability, which is the one of the highest reported values for inverted all-inorganic PVSCs. Meanwhile, the TPE-S layer can also be generally used to improve the performance of organic/inorganic hybrid inverted PVSCs, which show an outstanding power conversation efficiency of 21.0%, approaching the highest reported efficiency for inverted PVSCs. This work highlights the great potential of TPE-S as a simple and general dopant-free HTM for different types of high-performance PVSCs.     

Efficient Perovskite Solar Cells Fabricated Through CsCl‐Enhanced PbI2 Precursor via Sequential Deposition

The fabrication of high‐quality perovskite film highly relies on chemical composition and the synthesis method of perovskite. So far, sequentially deposited MA_0.03FA_0.97Pb(I_0.97Br_0.03)₃ polycrystalline film is adopted to produce high‐performance perovskite solar cells with record power conversion efficiency (PCE). Fewer grain boundaries and incorporation of inorganic cation (e.g., cesium) would further increase device performance via sequential deposition. Here, cesium chloride (CsCl) is introduced into lead iodide (PbI₂) precursor solution that beneficially modulates the property of PbI₂ film, leading to larger grains with cesium incorporation in the resulting perovskite film. The enlarged crystal grains originate from a slower nucleation process for CsCl‐containing PbI₂ film when reacting with formamidine iodide, confirmed by in situ confocal photoluminescence imaging. Photovoltaic devices based on CsCl‐containing PbI₂ film demonstrate a higher averaging efficiency of 21.3% than 20.3% of the devices without CsCl additives for reverse scan. More importantly, the device stability is improved by CsCl additives that retain over 90% of their initial PCE value after 4000 min tracking at maximum power point under 1‐sun illumination. This work paves a way to further improve the photovoltaic performance of mixed‐cation‐halide perovskite solar cells via a sequential deposition method.     

Dual‐Source Precursor Approach for Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

The highest efficiencies reported for perovskite solar cells so far have been obtained mainly with methylammonium and formamidinium mixed cations. Currently, high‐quality mixed‐cation perovskite thin films are normally made by use of antisolvent protocols. However, the widely used “antisolvent”‐assisted fabrication route suffers from challenges such as poor device reproducibility, toxic and hazardous organic solvent, and incompatibility with scalable fabrication process. Here, a simple dual‐source precursor approach is developed to fabricate high‐quality and mirror‐like mixed‐cation perovskite thin films without involving additional antisolvent process. By integrating the perovskite films into the planar heterojunction solar cells, a power conversion efficiency of 20.15% is achieved with negligible current density–voltage hysteresis. A stabilized power output approaching 20% is obtained at the maximum power point. These results shed light on fabricating highly efficient perovskite solar cells via a simple process, and pave the way for solar cell fabrication via scalable methods in the near future.