Q-Band pHEMT and mHEMT Subharmonic Gilbert Upconversion Mixers

This letter makes a comparison between Q-band 0.15 $mu{rm m}$ pseudomorphic high electron mobility transistor (pHEMT) and metamorphic high electron mobility transistor (mHEMT) stacked-LO subharmonic upconversion mixers in terms of gain, isolation and linearity. In general, a 0.15 $mu{rm m}$ mHEMT device has a higher transconductance and cutoff frequency than a 0.15 $mu{rm m}$ pHEMT does. Thus, the conversion gain of the mHEMT is higher than that of the pHEMT in the active Gilbert mixer design. The Q-band stacked-LO subharmonic upconversion mixers using the pHEMT and mHEMT technologies have conversion gain of $-$7.1 dB and $-$0.2 dB, respectively. The pHEMT upconversion mixer has an ${rm OIP}_{3}$ of $-$12 dBm and an ${rm OP}_{1 {rm dB}}$ of $-$24 dBm, while the mHEMT one shows a 4 dB improvement on linearity for the difference between the ${rm OIP}_{3}$ and ${rm OP}_{1 {rm dB}}$. Both the chip sizes are the same at 1.3 mm $times$ 0.9 mm.      

A 1 V 23 GHz Low-Noise Amplifier in 45 nm Planar Bulk-CMOS Technology With High-$Q$ Above-IC Inductors

A 23 GHz electrostatic discharge-protected low-noise amplifier (LNA) has been designed and implemented by 45 nm planar bulk-CMOS technology with high-$Q$ above-IC inductors. In the designed LNA, the structure of a one-stage cascode amplifier with source inductive degeneration is used. All high- $Q$ above-IC inductors have been implemented by thin-film wafer-level packaging technology. The fabricated LNA has a good linearity where the input 1 dB compression point $({rm IP}_{{-}1~{rm dB}})$ is ${- 9.5}~{rm dBm}$ and the input referred third-order intercept point $(P _{rm IIP3})$ is ${+ 2.25}~{rm dBm}$. It is operated with a 1 V power supply drawing a current of only 3.6 mA. The fabricated LNA has demonstrated a 4 dB noise figure and a 7.1 dB gain at the peak gain frequency of 23 GHz, and it has the highest figure-of-merit. The experimental results have proved the suitability of 45 nm gate length bulk-CMOS devices for RF ICs above 20 GHz.      

$S$ - and $C$ -Band Ultra-Compact Phase Shifters Based on All-Pass Networks

Ultra-compact phase shifters are presented. The proposed phase-shifting circuits utilize the lumped element all-pass networks. The transition frequency of the all-pass network, which determines the size of the circuit, is set to be much higher than the operating frequency. This results in a significantly small chip size of the phase shifter. To verify this methodology, 5-bit phase shifters have been fabricated in the $S$ - and $C$ -band. The $S$ -band phase shifter, with a chip size of 1.87 mm $,times,$0.87 mm (1.63 mm $^{2}$), has achieved an insertion loss of ${hbox{6.1 dB}} pm {hbox{0.6 dB}}$ and rms phase-shift error of less than 2.8$^{circ}$ in 10% bandwidth. The $C$ -band phase shifter, with a chip size of 1.72 mm $,times,$0.81 mm (1.37 mm $^{2}$), has demonstrated an insertion loss of 5.7 dB $pm$ 0.8 dB and rms phase-shift error of less than 2.3 $^{circ}$ in 10% bandwidth.      

17 GHz RF Front-Ends for Low-Power Wireless Sensor Networks

A 17 GHz low-power radio transceiver front-end implemented in a 0.25 $mu{hbox {m}}$ SiGe:C BiCMOS technology is described. Operating at data rates up to 10 Mbit/s with a reduced transceiver turn-on time of 2 $mu{hbox {s}}$, gives an overall energy consumption of 1.75 nJ/bit for the receiver and 1.6 nJ/bit for the transmitter. The measured conversion gain of the receiver chain is 25–30 dB into a 50 $Omega$ load at 10 MHz IF, and noise figure is 12 $pm$0.5 dB across the band from 10 to 200 MHz. The 1-dB compression point at the receiver input is $-$37 dBm and ${hbox{IIP}}_{3}$ is $-$25 dBm. The maximum saturated output power from the on-chip transmit amplifier is $-$1.4 dBm. Power consumption is 17.5 mW in receiver mode, and 16 mW in transmit mode, both operating from a 2.5 V supply. In standby, the transceiver supply current is less than 1 $mu{hbox {A}}$.      

A 0.1–5 GHz Cryogenic SiGe MMIC LNA

In this letter, the design and measurement of the first SiGe integrated-circuit LNA specifically designed for operation at cryogenic temperatures is presented. At room temperature, the circuit provides greater than 25.8 dB of gain with an average noise temperature $(T_{e})$ of 76 K $(NF=1 {rm dB})$ and $S_{11}$ of $-$ 9 dB for frequencies in the 0.1–5 GHz band. At 15 K, the amplifier has greater than 29.6 dB of gain with an average $T_{e}$ of 4.3 K and $S_{11}$ of $-$14.6 dB for frequencies in the 0.1–5 GHz range. To the authors' knowledge, this is the lowest noise ever reported for a silicon integrated circuit operating in the low microwave range and the first matched wideband cryogenic integrated circuit LNA that covers frequencies as low as 0.1 GHz.      

A Linearization Technique for RF Receiver Front-End Using Second-Order-Intermodulation Injection

A linearization technique is proposed in which low-frequency second-order-intermodulation $({rm IM}_{2})$ is generated and injected to suppress the third-order intermodulation $({rm IM}_{3})$. The proposed linearization technique is applied to both a low-noise amplifier (LNA) and a down-conversion mixer in an RF receiver front-end (RFE) working at 900 MHz. Fabricated in a 0.18$ mu{hbox{m}}$ CMOS process and operated at 1.5 V supply with a total current of 13.1 mA, the RFE delivers 22 dB gain with 5.3 dB noise figure (NF). The linearization technique achieves around 20 dB ${rm IM}_{3}$ suppression and improves the RFE's ${rm IIP}_{3}$ from $-$ 10.4 dBm to 0.2 dBm without gain reduction and noise penalty while requiring only an extra current of 0.1 mA.      

A $Q$ -Band Four-Element Phased-Array Front-End Receiver With Integrated Wilkinson Power Combiners in 0.18-$mu{{hbox{m}}}$ SiGe BiCMOS Technology

A four-element phased-array front-end receiver based on 4-bit RF phase shifters is demonstrated in a standard 0.18- $mu{{hbox{m}}}$ SiGe BiCMOS technology for $Q$-band (30–50 GHz) satellite communications and radar applications. The phased-array receiver uses a corporate-feed approach with on-chip Wilkinson power combiners, and shows a power gain of 10.4 dB with an ${rm IIP}_{3}$ of $-$13.8 dBm per element at 38.5 GHz and a 3-dB gain bandwidth of 32.8–44 GHz. The rms gain and phase errors are $leq$1.2 dB and $leq {hbox{8.7}}^{circ}$ for all 4-bit phase states at 30–50 GHz. The beamformer also results in $leq$ 0.4 dB of rms gain mismatch and $leq {hbox{2}}^{circ}$ of rms phase mismatch between the four channels. The channel-to-channel isolation is better than $-$35 dB at 30–50 GHz. The chip consumes 118 mA from a 5-V supply voltage and overall chip size is ${hbox{1.4}}times {hbox{1.7}} {{hbox{mm}}}^{2}$ including all pads and CMOS control electronics.      

$hbox{TiN/ZrO}_{2}$/Ti/Al Metal–Insulator–Metal Capacitors With Subnanometer CET Using ALD-Deposited $hbox{ZrO}_{2}$ for DRAM Applications

We provide the first report of the structural and electrical properties of $hbox{TiN/ZrO}_{2}$/Ti/Al metal–insulator–metal capacitor structures, where the $hbox{ZrO}_{2}$ thin film (7–8 nm) is deposited by ALD using the new zirconium precursor ZrD-04, also known as Bis(methylcyclopentadienyl) methoxymethyl. Measured capacitance–voltage ($C$– $V$) and current–voltage ( $I$–$V$) characteristics are reported for premetallization rapid thermal annealing (RTP) in $hbox{N}_{2}$ for 60 s at 400 $^{circ}hbox{C}$, 500 $^{circ}hbox{C}$, or 600 $^{ circ}hbox{C}$. For the RTP at 400 $^{circ}hbox{C}$ , we find very low leakage current densities on the order of nanoamperes per square centimeter at a gate voltage of 1 V and low capacitance equivalent thickness values of $sim$ 0.9 nm at a gate voltage of 0 V. The dielectric constant of $ hbox{ZrO}_{2}$ is 31 $pm$ 2 after RTP treatment at 400 $^{circ}hbox{C}$.      

2 MHz AO $Q$ -switched ${rm TEM}_{00}$ Grazing Incidence Laser With 3 at.% Neodymium Doped Nd:YVO$_{4}$

We present a detailed experimental and theoretical study of the ultrahigh repetition rate AO $Q$ -switched ${rm TEM}_{00}$ grazing incidence laser. Up to 2.1 MHz $Q$-switching with ${rm TEM}_{00}$ output of 8.6 W and 2.2 MHz $Q$ -switching with multimode output of 10 W were achieved by using an acousto-optics $Q$ -switched grazing-incidence laser with optimum grazing-incidence angle and cavity configuration. The crystal was 3 at.% neodymium doped Nd:YVO$_{4}$ slab. The pulse duration at 2 MHz repetition rate was about 31 ns. The instabilities of pulse energy at 2 MHz repetition rate were less than ${pm}6.7hbox{%}$ with ${rm TEM}_{00}$ operation and ${pm}3.3hbox{%}$ with multimode operation respectively. The modeling of high repetition rate $Q$-switched operation is presented based on the rate equation, and with the solution of the modeling, higher pump power, smaller section area of laser mode, and larger stimulated emission cross section of the gain medium are beneficial to the $Q$-switched operation with ultrahigh repetition rate, which is in consistent with the experimental results.      

A 0.55 V 60 dB-DR Fourth-Order Analog Baseband Filter

A 0.55 V supply voltage fourth-order low-pass continuous-time filter is presented. The low-voltage operating point is achieved by an improved bias circuit that uses different opamp input and output common-mode voltages. The fourth-order filter architecture is composed by two Active- ${rm G}_{rm m}{-}{rm RC}$ biquadratic cells, which use a single opamp per-cell with a unity-gain-bandwidth comparable to the filter cut-off frequency. The $-$ 3 dB filter frequency is 12 MHz and this is higher than any other low-voltage continuous-time filter cut-off frequency. The $-$3 dB frequency can be adjusted by means of a digitally-controlled capacitance array. In a standard 0.13 $mu{rm m}$ CMOS technology with ${V}_{THN}approx 0.25 {rm V}$ and ${V}_{THP}approx 0.3 {rm V}$, the filter operates with a supply voltage as low as 0.55 V. The filter $({rm total} {rm area}=0.47 {rm mm}^{2})$ consumes 3.4 mW. A 8 dBm-in-band IIP3 and a 13.3 dBm-out-of-band IIP3 demonstrate the validity of the proposal.      

A 3–10 GHz CMOS UWB Low-Noise Amplifier With ESD Protection Circuits

A low-power fully integrated low-noise amplifier (LNA) with an on-chip electrostatic-static discharge (ESD) protection circuit for ultra-wide band (UWB) applications is presented. With the use of a common-gate scheme with a ${rm g}_{rm m}$ -boosted technique, a simple input matching network, low noise figure (NF), and low power consumption can be achieved. Through the combination of an input matching network, an ESD clamp circuit has been designed for the proposed LNA circuit to enhance system robustness. The measured results show that the fabricated LNA can be operated over the full UWB bandwidth of 3.0 to 10.35 GHz. The input return loss $({rm S}_{11})$ and output return loss $({rm S}_{22})$ are less than ${-}8.3$ dB and ${-}9$ dB, respectively. The measured power gain $({rm S}_{21})$ is $11 pm 1.5$ dB, and the measured minimum NF is 3.3 dB at 4 GHz. The dc power dissipation is 7.2 mW from a 1.2 V supply. The chip area, including testing pads, is 1.05 mm$,times,$ 0.73 mm.      

10-GHz and 20-GHz Channel Spacing High-Resolution AWGs on InP

This letter reports on 10-GHz and 20-GHz channel-spacing arrayed waveguide gratings (AWGs) based on InP technology. The dimensions of the AWGs are 6.8$,times,$8.2 mm$^{2}$ and 5.0$,times,$6.0 mm$^{2}$, respectively, and the devices show crosstalk levels of $-$12 dB for the 10-GHz and $-$17 dB for the 20-GHz AWG without any compensation for the phase errors in the arrayed waveguides. The root-mean-square phase errors for the center arrayed waveguides were characterized by using an optical vector network analyzer, and are 18 $^{circ}$ for the 10-GHz AWG and 28$^{circ}$ for the 10-GHz AWG.      

A Wideband Low Noise Amplifier With 4 kV HBM ESD Protection in 65 nm RF CMOS

This study presents a wideband low noise amplifier (LNA) including electrostatic discharge (ESD) protection circuits using 65 nm CMOS with a gate oxide thickness of only ${sim}2$ nm. By co-designing the ESD blocks with the core circuit, the LNA shows almost no performance degradation compared to the reference design without ESD. Under a power consumption of only 6.8 mW, the silicon results show that the LNA can achieve a peak power gain of 13.8 dB. Within the 3 dB bandwidth from 2.6 GHz to 6.6 GHz, the noise figure (NF) is in a range of 4.0 dB to 6.5 dB and the input reflection coefficient $S_{11}$ is below ${-}13.0$ dB. Using the miniaturized Shallow-Trench-Isolation (STI) diode of ${sim}40$ fF capacitance and a robust gate-driven power clamp configuration, the proposed LNA demonstrates an excellent 4 kV human body mode (HBM) ESD performance, which has the highest voltage/capacitance ratio ( ${sim}100$ V/fF) among the published results for RF LNA applications.      

A 2–40 GHz Active Balun Using 0.13 $mu{rm m}$ CMOS Process

A 2 to 40 GHz broadband active balun using 0.13 $mu{rm m}$ CMOS technology is presented in this letter. Using two-stage differential amplified pairs, the active balun can achieve a wideband performance with the gain compensation technique. This active balun exhibits a measured small signal gain of ${0} pm{1}~{rm dB}$, with the amplitude imbalances below 0.5 dB and the phase differences of ${180} pm {10} ^{circ}$ from 2 to 40 GHz. The core active balun has a low power consumption of 40 mW, and a compact area of 0.8 mm $times,$ 0.7 mm. This proposed balun achieved the highest operation frequency, the widest bandwidth, and the smallest size among all the reported active baluns.      

Experimental Demonstration of Deeply-Etched SiO$_{2}$ Ridge Optical Waveguides and Devices

Deeply-etched ${hbox{SiO}}_{2}$ optical ridge waveguides are fabricated and characterized. A detailed discussion of the fabrication process (especially for the deep etching process) is presented. The measured propagation losses for the fabricated waveguides with different core widths range from $0.33sim {hbox {0.81}}~{hbox {dB}}/{hbox {mm}}$. The loss is mainly caused by the scattering due to the sidewall roughness. The losses in bending sections are also characterized, which show the possibility of realizing a small bending radius (several tens of microns). 1 $,times {rm N}$ ( ${rm N}=2$, 4, 8) multimode interference couplers based on the deeply-etched ${hbox{SiO}}_{2}$ ridge waveguide are also fabricated and show fairly good performances.      

A 0.13 $mu$ m CMOS Quad-Band GSM/GPRS/EDGE RF Transceiver Using a Low-Noise Fractional-N Frequency Synthesizer and Direct-Conversion Architecture

This paper presents a single-chip CMOS quad-band (850/900/1800/1900 MHz) RF transceiver for GSM/GPRS/EDGE applications which adopts a direct-conversion receiver, a direct-conversion transmitter and a fractional-N frequency synthesizer with a built-in DCXO. In the GSM mode, the transmitter delivers 4 dBm of output power with 1$^{circ}$ RMS phase error and the measured phase noise is ${-}$164.5 dBc/Hz at 20 MHz offset from a 914.8$~$MHz carrier. In the EDGE mode, the TX RMS EVM is 2.4% with a 0.5 $~$dB gain step for the overall 36 dB dynamic range. The RX NF and IIP3 are 2.7 dB/ ${-}$12 dBm for the low bands (850/900 MHz) and 3 dB/${-}$ 11 dBm for the high bands (1800/1900 MHz). This transceiver is implemented in 0.13 $mu$m CMOS technology and occupies 10.5 mm$^{2}$ . The device consumes 118 mA and 84 mA in TX and RX modes from 2.8 V, respectively and is housed in a 5$,times,$ 5 mm$^{2}$ 40-pin QFN package.      

Temperature-Insensitive Dual-Comb Filter Based on Multimode Interference Ti : LiNbO $_{3}$ Waveguide

A temperature-insensitive dual-comb filter has been demonstrated for the first time by multimode interference based on a Ti : LiNbO$_{3}$ channel waveguide. The phase difference between comb filters was about 180 $^{circ}$. We only observed less than ${pm}$0.125-nm variation of the center wavelength of the filter during temperature change from 20 $^{circ}$C to 50 $^{circ}$C. The measured extinction ratio and channel spacing of the comb filter were about ${-}$25 dB and 3.2 THz, respectively.      

Bending and Strain Sensitivities in a Helicoidal Long-Period Fiber Gratings

In this letter, we report bending and strain sensitivities of helicoidal long-period fiber gratings fabricated by twisting single-mode fibers during $hbox{CO}_{2}$ laser irradiation. Linear spectral shifts of the resonant wavelengths under the bending and tensile strain were observed with the sensitivities of $-$11.7 nm/m$^{-1}$ and $-$1.1 $hbox{pm}/muvarepsilon$, respectively. The corresponding transmission power variations at the resonance wavelength were 4.1 $hbox{dB/m}^{-1}$ and $2.2times 10^{-4} hbox{dB}/muvarepsilon$, respectively. Detailed measurement techniques and sensor applications are discussed.      

W-Band Active Down-Conversion Mixer in Bulk CMOS

A W-band (76–77 GHz) active down-conversion mixer has been demonstrated using low leakage (higher ${rm V}_{{rm T}}$) NMOS transistors of a 65-nm digital CMOS process with 6 metal levels. It achieves conversion gain of ${-}8$ dB at 76 GHz with a local oscillation power of 4 dBm (${sim-}2$ dBm after de-embedding the on-chip balun loss), and 3 dB bandwidth of 3 GHz. The SSB noise figures are 17.8–20 dB (11.3–13.5 dB after de-embedding on-chip input balun loss) between 76 and 77 GHz. ${rm IP}_{1{rm dB}}$ is ${-}6.5$ dBm and IIP3 is 2.5 dBm (${sim-}13$ and ${sim}-4$ dBm after de-embedding the on-chip balun loss). The mixer consumes 5 mA from a 1.2 V supply.      

A Fully Integrated 5 GHz Low-Voltage LNA Using Forward Body Bias Technology

A fully integrated 5 GHz low-voltage and low-power low noise amplifier (LNA) using forward body bias technology, implemented through a 0.18 $mu{rm m}$ RF CMOS technology, is demonstrated. By employing the current-reused and forward body bias technique, the proposed LNA can operate at a reduced supply voltage and power consumption. The proposed LNA delivers a power gain (S21) of 10.23 dB with a noise figure of 4.1 dB at 5 GHz, while consuming only 0.8 mW dc power with a low supply voltage of 0.6 V. The power consumption figure of merit $(FOM_{1})$ and the tuning-range figure of merit $(FOM_{2})$ are optimal at 12.79 dB/mW and 2.6 ${rm mW}^{-1}$, respectively. The chip area is 0.89 $,times,$0.89 ${rm mm}^{2}$.