Thermal wear and electrical sliding wear behaviors of the polyimide modified polymer-matrix pantograph contact strip

In the present study, the polyimide resin (PI)/cashew-modified resin (YM) polymer-matrix pantograph contact strip (PMPCS) was prepared by using hot repressing, hydro-solidification and dipping treatment processes. The thermal properties of cured resins were studied by thermogravimetry analyzer and differential scanning calorimetry. The thermal wear and electrical sliding wear behaviors of PMPCS against copper were evaluated by a ring block wear tester at elevated temperature under dry sliding conditions and a wear tester which simulated the train motion under laboratory conditions, respectively. Worn surfaces and wear debris of PMPCS were analyzed by scanning electron microscopy and energy dispersive spectrometer, and the wear mechanism was discussed. It has been found that the thermal stability of the PI/YM is superior to that of the YM under the same testing conditions. The results also showed that PI/YM-PMPCS had superior wear resistance than that of YM-PMPCS at elevated temperature and with electrical current. At elevated temperature, the wear mechanism of tribological pair evolved from adhesive wear to oxidative wear with mild delamination wear. Arc erosion wear, oxidative wear, and adhesive wear were the dominant mechanisms of tribological pair during the electrical wearing process.     

Differences in Mechanisms for Fretting Wear Reduction between Oil and Grease Lubrication

The different mechanisms of fretting wear in oil and grease lubrication and methods to reduce fretting wear were examined by means of thrust ball bearings in this study. Tests of fretting wear under oil lubrication were conducted. It was confirmed that high-viscosity oil can reduce fretting wear at high velocity (i.e., high frequency) through oil film formation. In the case of grease lubrication, the influence of velocity on fretting wear was significantly different for low- and high-viscosity greases. Grease with low-viscosity base oils could reduce fretting wear at high velocity. In contrast, grease with high-viscosity base oils could reduce fretting wear at low velocity. Grease thickeners were found to be effective in forming a layer that could prevent fretting wear. These results highlight the large differences in effective fretting wear reduction mechanisms between oil and grease lubrication.     

Third body effects on friction and wear during fretting of steel contacts

Fretting wear proceeds through particle detachment from the contacting surfaces which, while trapped in the contact zone, can affect the frictional and wear response. Ball-on-flat fretting experiments were carried out between steel specimens under gross slip regime. A transition in the coefficient of friction was linked to a critical contact pressure. The microstructure and chemical composition of the third body evolve with the applied pressure. The evolution of the friction coefficient is strongly dependent on the third body properties. The wear is controlled by the applied load and thus the real contact area within the wear track.     

Fretting and fretting corrosion behavior of novel micro alloyed rail steels

The fretting behavior of two novel rail steels of composition Cu–Ni and Cr–Cu–Ni has been studied and compared with that of C–Mn and Cu–Mo rail steels. The rail steels were fretted in dry condition and in 3.5% NaCl solution. All the four rail steels exhibited similar fretting behavior in dry condition. The morphological features of the wear scar surface indicated delamination process as the main wear mechanism. The wear damage in 3.5% NaCl was lower compared to that in dry condition for all the rail steels due to lubricating effect of the solution. Fretting in presence of 3.5% NaCl resulted in lower wear volume for Cu–Ni and Cr–Cu–Ni rail steels. The friction coefficient for Cr–Cu–Ni rail steel was lower than that of C–Mn, Cu–Mo and Cu–Ni rail steels. Scanning electron microscopy (SEM) showed better adherence of tribo-electro-chemical layers formed on Cu–Ni and Cr–Cu–Ni rail steel than the C–Mn and Cu–Mo rail steels. This has been related to the improved fretting corrosion behavior of Cu–Ni and Cr–Cu–Ni rail steels.     

Fretting wear behaviors of a railway axle steel

Fretting damage was one of the most important reasons for the failure of the railway axle. Fretting wear (tangential fretting mode) tests of a railway axle steel (LZ50 steel) flats against 52 100 steel balls were carried out under different normal loads and displacement amplitudes on a hydraulic fretting wear rig. Dynamic analyses in combination with microscopic examinations have been performed. The experimental results showed that the fretting regimes of the LZ50 steel were strongly dependent upon the imposed normal loads and displacement amplitudes. The F_t/F_n curves exhibited different variation trends in different fretting running regimes. The fretting scars presented slight damage in partial slip regime. In mixed fretting regime, the trace of the plowing and plastic deformation flow can be observed on the fretting scars. The wear mechanism during this regime was the combination of the abrasive wear, oxidative wear and delamination accompanied with obvious plastic deformation. The detachment of particles and plowing traces were the main phenomena in slip regime. And, thicker debris layer covered the contact zone of the scar. The severe degradation in slip regime presented the main wear mechanisms of abrasive wear, oxidative wear and delamination.     

Fretting fatigue and wear damage of structural components in nuclear power stations—Fitness for service and life management perspective

Fretting fatigue and wear problems have major economical and safety impact on the nuclear industry. This keynote paper provides examples of the fretting problems encountered in nuclear power stations and an overview of the methodologies used to assess their root cause, their potential effect on the integrity of structural components and the future damage projection for risk management. The limitations of existing models that are commonly used to predict fretting wear rate are discussed. A system approach to the fretting wear/fatigue problem allowed us to significantly improve the capability of predicting fretting damage through the recognition of the problem nonlinearity, and the effect of self-induced changes. The application of linear elastic fracture mechanics principles for predicting the fretting wear and fretting fatigue strength is demonstrated. The paper underlines the critical roles of the following two factors. First, the validation of the above mentioned methodologies, through experimental investigation of the long-term fretting wear and fatigue behavior of structural components under realistic operating conditions. Second, the qualification of in -situ measurements of fretting wear damage using nondestructive evaluation NDE and inspection methods.     

Fretting wear behaviour of polymethylmethacrylate under linear motions and torsional contact conditions

The fretting wear behaviour of PMMA against a rigid counterface has been investigated under various contact zone kinematic conditions. A specific device has been used in order to achieve load axis spin or stationary rolling motions in a contact between a PMMA flat and a steel ball. Wear processes under such conditions have been investigated by means of laser profilometry and in-situ optical observations of the contact area during tests. Very different wear patterns were produced depending on the contact kinematics. For stationary rolling conditions, the progressive accumulation and compaction of debris induced the formation of a single ripple located in the middle of the contact. Very little debris was found to be eliminated from the contact and the resulting wear was quite low. On the other hand, little accumulation of debris was observed for torsional contact conditions and the wear was drastically enhanced. These results are analysed by considering the effects of contact zone kinematics on particle detachment and third body elimination.     

Fretting wear behavior of TiB2-based materials against bearing steel under water and oil lubrication

Lubricated fretting tests in water and paraffin oil were performed with a monolithic TiB₂, a TiB₂-based cermet with 16 vol.% Ni₃(Al, Ti) binder, a sialon–TiB₂ (60/40) composite and a ZrO₂–TiB₂ (70/30) composite against ball bearing grade steel. Based on the measured friction and wear data, the ranking of the investigated fretting couples was evaluated. Furthermore, the morphological investigations of the worn surfaces and transfer layers are carried out and the wear mechanisms for the investigated friction couples are elucidated. While fretting in water, experiments revealed that tribochemical reactions, coupled with mild abrasion, played a major role in the wear behavior of the studied material combinations. ZrO₂–TiB₂ (70/30)/steel wear couple has been found to have the highest fretting wear resistance among the different tribocouples under water lubrication. Under oil lubrication, extensive cracking of the paraffin oil at the fretting contacts, caused by tribodegradation, leads to the deposition of a carbon-rich lubricating layer, which significantly reduced friction and wear of all the investigated tribosystems.     

Fretting-induced friction and wear in large flat-on-flat contact with quenched and tempered steel

Fretting may cause severe surface damage and lead to unexpected fatigue failure. Our test apparatus was designed based on reciprocating, large, annular flat-on-flat contact without any edge effects in the direction of the fretting movement. Fretting wear tests were run with quenched and tempered steel with different normal pressures and sliding amplitudes under gross sliding conditions. The development of the friction coefficient and total wear mass depended mostly on the accumulated sliding distance. Initially, friction and wear were highly adhesive but gradually changed to abrasive due to third body accumulation in the interface.     

Fretting wear of thin steel wires. Part 2: Influence of crossing angle

The wear behaviour of thin steel wires has been analyzed under oscillating sliding conditions in crossed cylinders contact geometry. The focus of this analysis was the influence of the crossing angle between the wires on the wear. The wires used had 0.45 mm in diameter and the material was cold-drawn eutectoid carbon steel (0.8% C) with a tensile strength higher than 2800 MPa. Two different types of tests were carried out, the first one representing the influence of the crossing angle for a constant load and the second one representing the influence of the crossing angle with constant contact pressure. In the first type of tests it was seen that as the contact angle decreases the contact pressure decreases too and hence less energy specific wear resistance is observed. As a consequence less wear is produced, thus increasing the life of the wires. In the second type of tests it was seen that with constant contact pressure but different crossing angles, nearly the same energy specific wear resistance was observed. This points at an identical wear behaviour in both type of tests but with a running-in and a steady state period as two different wear periods. The tests showed that the running in period may play an important role in the overall wear particle generation and hence the wear occurring in the steady state period is rather mild.     

An experimental study torsional fretting behaviors of LZ50 steel

Four simple fretting modes are defined according to relative motion: tangential, radial, rotational, and torsional fretting. This paper presents a new test rig that was developed from a low-speed reciprocating rotary system to show torsional fretting wear under ball-on-flat contact. Torsional fretting behavior was investigated for LZ50 steel flats against AISI52100 steel balls under various angular displacement amplitudes and normal loads. The friction torques and dissipation energy were analyzed in detail. Two types of T–θ curves in the shape of quasi-parallelograms and ellipticals were found that correspond to gross and partial slips, respectively. The experimental results showed that the dynamic behavior and damage processes depend strongly on the normal loads, angular displacement amplitudes, and cycles. In this paper, the debris and oxidation behaviors and detachment of particles in partial and gross slip regimes are also discussed. Debris and oxidation are shown to have important roles during the torsional fretting processes. The wear mechanism of torsional fretting was a combination of abrasive and oxidative wear and delamination before third-body bed formation. The mechanism was then transformed into third-body wear after a great amount of debris formed.     

Effect of contact load on fretting fatigue behaviour of steel wires

Abstract

The tension–tension fretting fatigue tests of steel wires were performed on a self-made fretting fatigue test equipment under contact loads ranging from 40 to 70 N and a strain ratio of 0·8. The results showed that when the contact load increased, the fretting regime of steel wires transformed from gross slip regime to mixed fretting regime. The fretting fatigue life in the mixed fretting regime was significantly lower than that in the gross slip regime. The main fretting wear mechanisms in the gross slip regime, where there were serious fretting damage and a lot of wear debris, were abrasive wear and fatigue wear. Microcracks were observed in the fretting scar of the mixed fretting regime, and the main fretting wear mechanisms were adhesive and fatigue wears. The fretting wear scar was the fatigue source region, and the fatigue fracture surface could be divided into three regions.     

Fretting wear behavior of AZ91D and AM60B magnesium alloys

The fretting wear behavior of the AZ91D and AM60B magnesium alloys are investigated using a reciprocating fretting wear machine under dry conditions with different numbers of cycles, different normal loads, slip amplitudes and frequencies. The worn surfaces and wear debris were examined using scanning electron microscopy and optical microscopy in order to understand the predominant wear mechanisms of two magnesium alloys. The results indicate that the AZ91D alloy displays a lower friction coefficient and lower wear quantity than the AM60B alloy. The AZ91D shows a higher capability than AM60B in resisting crack nucleation and propagation. Both AZ91D and AM60B show similar friction and wear characteristics. The wear quantity increases with increasing normal load, but decreases with increasing frequency. The friction coefficient also decreases as the normal load is increased. Fretting frequency had little effect on the friction coefficient. In a long term, the fatigue wear and abrasive wear were the predominant wear mechanisms for AM60B and delamination wear, adhesive wear and abrasive wear for AZ91D.     

Fretting wear and friction behaviour of engineering ceramics

Friction and wear characteristics of partially stabilized zirconia (PSZ) fretted against itself and against high carbon steel were investigated. The results for the transformation toughened PSZ ceramics are compared with the behaviour of more brittle alumina ceramic under the same test conditions. Fretting tests in air were carried out on a high frequency wear test rig at room temperature using a cross-cylinder configuration. It was found that both the oxide ceramics were more resistant to fretting wear than the steel. Surface cracking was observed on the alumina wear scars while microfracture and delamination dominated on the PSZ wear scars. When metallic samples were fretted against ceramics, metallic film transfer to the ceramic surfaces occurred.     

Fretting wear of carburized titanium alloy against ZrO2 under serum lubrication

Fretting wear of carburized titanium alloys was investigated on the universal multifunctional tester (UMT) with the ball-on-flat fretting style under bovine serum lubrication. The tangential load and friction coefficient during the fretting process were analyzed, and the evolution of fretting log during the fretting process was investigated to understand the wear mechanism of the titanium alloy and carburized titanium alloy. Furthermore, the wear scar was examined using a SEM and three-dimension surface profiler. It was found that the friction coefficient of the titanium alloy increased faster than that of carburized titanium alloy in the first stage under serum lubrication, and then remained steady with a similar value in the second stage. The Ft-D curve indicated that there was wear mechanism transition from gross slip to mixed stick and slip. Finally, it was observed that there was a slight damage of the titanium alloy and carburized titanium alloy showed excellent performance during the fretting wear process under serum lubrication. All of the results suggested that carburized titanium alloy was a potential candidate for the stem material in artificial joints.     

钢丝微动磨损过程中的接触力学问题研究

钢丝间的微动磨损以及由此引起的钢丝的疲劳断裂是提升钢丝绳失效的主要原因之一.以6×19点接触式提升钢丝绳为研究对象,将钢丝绳中钢丝的微动损伤过程进行实验室模型化,在自制的钢丝微动磨损试验机上进行钢丝试样的微动磨损实验,考察接触载荷和微动时间变化对钢丝试样磨损深度的影响.结果表明,钢丝试样的微动磨损深度随着接触载荷和微动时间的增加而呈增长趋势,但由于接触面积和接触应力在微动磨损过程中随着接触载荷和微动时间的变化而变化,使磨损深度在不同磨损工况下增长趋势不同.建立的钢丝接触有限元模型表明,接触区中心的最大接触应力随着接触载荷的增加而增大,随着嵌入深度的加深而减小.其结果验证了试验过程中接触面积和接触应力对磨损深度的影响关系.     

Friction and Wear Characteristics Due to Stick-Slip under Fretting Conditions

Friction and wear characteristics between two steel surfaces under fretting conditions are investigated experimentally. The fretting damage caused by low-amplitude oscillatory sliding can be classified into three regimes of gross-slip, mixed-slip, and partial-slip due to the stick-slip phenomenon. One of the most important characteristics of fretting wear is the transition from gross-slip to mixed-slip. Several criteria have been introduced for a quantitative determination of the transition between mixed-slip and gross-slip. However, the transition criteria have some problems in determining the regimes because parameters are difficult to calculate or depend on the system. To introduce new transition criteria in this study, the phase difference between friction force and relative displacement is used to determine the transition and predict the fretting wear. It is found that the phase difference with a range of 0° to 90° can predict the onset of fretting conditions.     

Fretting wear characteristics of cold gas-dynamic sprayed aluminum alloys

Process selection for repair of mechanical components due to wear and corrosion, e.g. damage of aluminum casting housings of fuel injection systems, is based on cost and response time factors, provided that the mechanical performance is maintained within acceptable limits. One of the promising and emerging repair technologies is Cold Gas-Dynamic Spray (CGDS) coating, where a high-pressure gas propels fine powder particles to very high velocities to produce surface coating. It is essential to identify the optimum process conditions and powder composition to produce repaired surfaces with tribological properties close to those of the originally manufactured part (without coating). The objective of this work is to compare the dynamic friction and fretting wear properties of the repaired surfaces using various types of coating composition and spraying techniques. Eight types of CGDS coatings, applied to AMS 4260 aluminum specimens, were fretted against 440C stainless steel specimens at low and high nominal loads to assess their fretting wear resistance, dynamic friction properties and damping capacity. The optimum coating composition and process conditions were identified. In comparison to the uncoated specimen, this optimum coating offered tribological characteristics close to the uncoated material and even better dynamic friction properties.     

Fretting wear of Al-Si alloy matrix composites

Ball-against-disk type fretting wear tests for Al-Si alloy matrix composites in contact with bearing steel were conducted in wet air to investigate the effects of relative slip amplitude on friction and wear of the composites. In the larger range of relative slip amplitude, the Al-Si alloy-impregnated graphite composite (ALGR-MMC) shows lower friction coefficients than those of alumina short fiber-reinforced composite (ASFR-MMC) and hollow silica particle-reinforced composite (HSPR-MMC). Although the wear rate of the ALGR-MMC is higher than that of the ASFR-MMC and HSPR-MMC, the composite hardly causes damage to the mating material due to adhesion of compacted films of graphite powder and Al-Si alloy wear particles.     

Fretting fatigue strength estimation considering the fretting wear process

In fretting fatigue process the wear of contact surfaces near contact edges occur in accordance with the reciprocal micro-slippages on these contact surfaces. These fretting wear change the contact pressure near the contact edges. To estimate the fretting fatigue strength and life it is indispensable to analyze the accurate contact pressure distributions near the contact edges in each fretting fatigue process.So, in this paper we present the estimation methods of fretting wear process and fretting fatigue life using this wear process. Firstly the fretting-wear process was estimated using contact pressure and relative slippage as follows:

W=K×P×S,