Niobium sulfide as a dopant for hydrotreating NiMo catalysts

Niobium sulfide has been recently found to be an interesting new active phase for hydrodesulfurization. In this work, niobium was used as a dopant for a conventional hydrotreating catalyst. A NiMo hydrotreating catalyst in the oxide form was doped with various contents of Nb precursor salt (02 sulfiding agent in a high pressure vessel. The use of this new dopant increased the catalytic activity in both HDS and HYD model reactions. Highest activities were obtained with an optimum Nb content of 5 wt.%. The selectivity of the products was also modified since more isomerized compounds where produced. Various techniques were used to determine structural and morphological characteristics of the materials. TEM pictures only showed the presence of lamellar particles similar to MoS₂. EDX analysis demonstrated the homogeneous distribution of the transition metal elements (Ni, Mo, Nb) even with small electron probes at high magnification. EXAFS was used to determine the local environment of Nb atoms and showed that Nb was present in the form of “NbS₂” entities similar to the bulk phase.     

Hydrodesulfurization of thiophene, dibenzothiophene and gas oil on various Co---Mo/TiO2-Al2O3 catalysts

Evaluation of Co---Mo catalysts prepared on various TiO₂-Al₂O₃ supports has been made for thiophene under atmospheric pressure, dibenzothiophene under high pressure and gasoil in a classical pilot plant. Comparison of activities indicates DBT as more representative of a real feedstock and the Co---Mo/TiO₂ (50%)-Al₂O₃ (50%) catalyst appears more active than the Co---Mo/Al₂O₃ sample toward HDS, HDN and hydrodearomatization.     

Effects of small MoO3 additions on the properties of nickel catalysts for the steam reforming of hydrocarbons III. Reduction of Ni-Mo/Al2O3 catalysts

Ni/Al₂O₃ catalyst modified by small amounts of Mo show unusual properties in the steam reforming of hydrocarbons. There are no data about the effect of small amounts of molybdenum on reduction of the Ni-Mo supported catalysts. The properties of these very complex systems depend on the conditions of successive preparation stages (calcination, reduction) or the process conditions.

A series of Ni/Al₂O₃ catalysts modified by Mo were prepared in order to investigate the influence of promoter amounts and preparation sequence on their properties. Temperature programmed reduction (TPR) has been employed to study the reducibility of Ni-Mo/Al₂O₃ catalysts. Catalysts were further characterized by BET area, H₂ chemisorption and X-ray diffraction measurements.

The TPR curves of Ni-Mo/Al₂O₃ catalysts are very complex. Mo addition leads to the decrease of catalysts reducibility. However, complete reduction of NiO and MoO₃ can be achieved at 800 °C. The reduction course depends on the sequence of nickel and molybdenum addition into the support. Precise measurements of Ni peaks positions in the XRD pattern of Ni/Al₂O₃ and Ni-Mo/Al₂O₃ samples show the possibility of Ni-Mo solid solution formation.     

TiO2-coated on Al2O3 support prepared by the CVD method for HDS catalysts

Mo---Co or Mo---Ni catalysts supported on alumina (Al₂O₃) have been widely used for hydrodesulfurization (HDS) of heavy petroleum fractions. In order to enhance the catalytic activities for HDS, a composite type support (TiO₂-Al₂O₃) prepared by the chemical vapor deposition (CVD) method has been studied. We found that Mo catalyst supported on TiO₂-Al₂O₃ showed much higher catalytic activity for HDS of dibenzothiophene derivatives than the catalysts supported on Al₂O₃.     

Catalytic activities of Co(Ni)Mo/TiO2–Al2O3 catalysts in gasoil and thiophene HDS and pyridine HDN: effect of the TiO2–Al2O3 composition

The effect of the TiO₂–Al₂O₃ mixed oxide support composition on the hydrodesulfurization (HDS) of gasoil and the simultaneous HDS and hydrodenitrogenation (HDN) of gasoil+pyridine was studied over two series of CoMo and NiMo catalysts. The intrinsic activities for gasoil HDS and pyridine HDN were significantly increased by increasing the amount of TiO₂ into the support, and particularly over rich- and pure-TiO₂-based catalysts. It is suggested that the increase in activity be due to an improvement in reducing and sulfiding of molybdena over TiO₂. The inhibiting effect of pyridine on gasoil HDS was found to be similar for all the catalysts, i.e., was independent of the support composition. The ranking of the catalysts for the gasoil HDS test differed from that obtained for the thiophene test at different hydrogen pressures. In the case of gasoil HDS, the activity increases with TiO₂ content and large differences are observed between the catalysts supported on pure Al₂O₃ and pure TiO₂. In contrast, in the case of the thiophene test, the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also, in the thiophene test the difference in intrinsic activity between the pure Al₂O₃-based catalyst appeared relatively more active than the catalysts supported on mixed oxides. Also in the thiophene test, the difference in intrinsic activity between the pure Al₂O₃- and pure TiO₂-based catalysts is relatively small and dependent on the H₂ pressure used. Such differences in activity trend among the gasoil and the thiophene tests are due to a different sensitivity of the catalysts (by different support or promoter) to the experimental conditions used. The results of the effect of the H₂ partial pressure on the thiophene HDS, and on the effect of H₂S concentration on gasoil HDS demonstrate the importance of these parameters, in addition to the nature of the reactant, to perform an adequate catalyst ranking.     

Reactivity of V2O5-WO3/TiO2 catalysts in the selective catalytic reduction of nitric oxide by ammonia

The physico-chemical characteristics and the reactivity of sub-monolayer V₂O₅-WO₃/TiO₂ deNO_x catalysts is investigated in this work by EPR, FT-IR and reactivity tests under transient conditions. EPR indicates that tetravalent vanadium ions both in magnetically isolated form and in clustered, magnetically interacting form are present over the TiO₂ surface. The presence of tungsten oxide stabilizes the surface V^IV and modifies the redox properties of V₂O₅/TiO₂ samples. Ammonia adsorbs on the catalysts surface in the form of molecularly coordinated species and of ammonium ions. Upon heating, activation of ammonia via an amide species is apparent. V₂O₅-WO₃/TiO₂ catalysts exhibits higher activity than the binary V₂O₅/TiO₂ and WO₃/TiO₂ reference sample. This is related to both higher redox properties and higher surface acidity of the ternary catalysts. Results suggest that the catalyst redox properties control the reactivity of the samples at low temperatures whereas the surface acidity plays an important role in the adsorption and activation of ammonia at high temperatures.     

Gold/iron carbonyl clusters as precursors for TiO2 supported catalysts

A series of supported gold/iron catalysts has been prepared from bimetallic carbonyl clusters and characterized to determine how the nature of the precursors and the thermal treatment conditions affected the dispersion of the active phase and the catalytic activity. The chemical–physical characterization, and the catalytic tests carried out, evidenced that the deposition of bimetallic Au/Fe carbonyl clusters on a titania support, and their following controlled decomposition, is a way to obtain stable catalysts, active in the decomposition of toluene.     

Support effects in Pt/TiO2–ZrO2 catalysts for NO reduction with CH4

ZrO₂–TiO₂ mixed oxides, prepared using the sol–gel method, were used as supports for platinum catalysts. The effects of catalyst pre-reduction and surface acidity on the performance of Pt/ZT catalysts for the reduction of NO with CH₄ were studied. The diffuse reflectance infrared Fourier transformed (DRIFT) spectra of CO adsorbed on the Pt/ZT catalysts, and also on the Pt/T and Pt/Z references, pre-reduced at 773 K in hydrogen, revealed that an SMSI state is developed in the Ti-rich oxide-supported platinum catalysts. However, no shift in the binding energy of Pt 4f_7/2 level for Pt/T and Pt deposited on Ti-rich support counterparts pre-reduced at 773 K was found by photoelectron spectroscopy. The DRIFT spectra of the catalysts under the NO+O₂ co-adsorption revealed the appearance of nitrite/nitrate species on the surface of the Zr-containing catalysts, which displayed acidic properties, but were almost absent in the Pt/T catalyst. The intensity of these bands reached a maximum for the Pt/ZT(1:1) catalyst, which in turn exhibited a larger specific area. In the absence of oxygen in the feed stream, the NO+CH₄ reaction showed DRIFT spectra assigned to surface isocyano species. Since the intensity of this band is higher for the Pt/ZT (9:1) catalyst, it seems that such species are developed at the Pt–support interface.     

Deactivation of Co---Mo/A12O3 hydrodesulfurization catalysts during a one-year commercial run

A series of Co---Mo catalysts with different Co and Mo loadings were prepared and exposed to a commercial HDS run for a year. From the activity tests using model compounds, the HDS activity of the fresh catalyst was found to increase up to 4.0 Mo atoms nm⁻² with increasing Co---Mo loading. However, no significant difference in the activity was observed in the used catalysts. TEM and EXAFS analyses revealed that the MOS₂ stacks aggregated in the lateral direction but did not grow in the normal direction to the layers during the run.     

Preparation of Co–Mo/B2O3/Al2O3 catalysts for hydrodesulfurization: Effect of citric acid addition

The effect of citric acid (CA) addition was studied on the HDS of thiophene over Co–Mo/(B)/Al₂O₃ catalysts. The catalysts were characterized by means of LRS, Mo K-edge EXAFS, NO adsorption capacity measurements, and UV–vis spectra. The catalysts were subjected to a chemical vapor deposition (CVD) technique using Co(CO)₃NO as a precursor of Co in order to get deeper insights into the effect of citric acid addition. It was shown that the HDS activity was enhanced by the citric acid addition up to the CA/Mo mole ratio of around 1 and leveled off with further addition. The amount of Co anchored by the CVD was increased by the addition of citric acid, suggesting an increase in the dispersion of MoS₂ particles on the catalyst by the simultaneous presence of Co, Mo and citric acid, in conformity with the increase in the NO adsorption capacity. In contrast to Co–Mo catalysts, the edge dispersion of MoS₂ particles in Mo/B/Al₂O₃ was not affected by the addition of citric acid. The LRS, UV–vis spectra and Mo K-edge EXAFS showed that Co–CA and Mo–CA surface complexes are formed by the addition of citric acid. The Co–CA surface complex is more preferentially formed on CoMo/Al than on CoMo/B/Al, in agreement with a greater promoting effect of citric acid at a lower CA/Mo mole ratio for CoMo/Al than for CoMo/B/Al.     

Characterization of Ni---W/A12O3-SiO2 aromatics saturation catalysts used in a one-year commercial HDS run

A series of Ni---W/A1₂O₃-SiO₂ catalysts with different A1₂O₃/SiO₂ ratios were prepared and loaded in a commercial HDS unit for a year. The catalytic properties of the freshly sulfided and spent catalysts were investigated by performing structural analyses and model test reactions. The aggregation of the WS₂ slabs in the lateral direction, which was observed by EXAFS and TEM, was a major cause of the catalyst deactivation. The addition of SiO₂ into the catalyst support was found to suppress the structural changes of the catalyst.     

负载型CuMnO_x/TiO_2催化剂催化燃烧甲苯

采用沉积-沉淀法制备CuMnO_x/TiO_2新型甲苯燃烧催化剂,考察焙烧温度、Cu与Mn物质的量比、Cu和Mn总负载量、空速及水蒸汽含量对催化甲苯燃烧性能的影响。研究表明,焙烧温度500℃和Cu与Mn物质的量比为1∶1时,催化剂活性最好,反应温度250℃时,甲苯去除率为100%;水蒸汽的出现明显降低了甲苯转化率。XRD和H2-TPR表征结果表明,CuMnO_x/TiO_2催化剂的主要活性相为铜锰尖晶石(Cu1.5Mn1.5O4),它的存在降低了CuMnO_x/TiO_2催化剂的还原温度,是催化活性优良的主要原因。     

TiO2-SiO2 and V2O5/TiO2-SiO2 catalyst: Physico-chemical characteristics and catalytic behavior in selective catalytic reduction of NO by NH3

TiO₂-SiO₂ with various compositions prepared by the coprecipitation method and vanadia loaded on TiO₂-SiO₂ were investigated with respect to their physico-chemical characteristics and catalytic behavior in SCR of NO by NH₃ and in the undesired oxidation of SO₂ to SO₃, using BET, XRD, XPS, NH₃-TPD, acidity measurement by the titration method and activity test. TiO₂-SiO₂, compared with pure TiO₂, exhibits a remarkably stronger acidity, a higher BET surface area, a lower crystallinity of anatase titania and results in allowing a good thermal stability and a higher vanadia dispersion on the support up to high loadings of 15 wt% V₂O₅. The SCR activity and N₂ selectivity are found to be more excellent over vanadia loaded on TiO₂-SiO₂ with 10–20 mol% of SiO₂ than over that on pure TiO₂, and this is considered to be associated with highly dispersed vanadia on the supports and large amounts of NH₃ adsorbed on the catalysts. With increasing SiO₂ content, the remarkable activity decrease in the oxidation of SO₂ to SO₃, favorable for industrial SCR catalysts, was also observed, strongly depending on the existence of vanadium species of the oxidation state close to V⁴⁺ on TiO₂-SiO₂, while V⁵⁺ exists on TiO₂, according to XPS. It is concluded that vanadia loaded on Ti-rich TiO₂-SiO₂ with low SiO₂ content is suitable as SCR catalysts for sulfur-containing exhaust gases due to showing not only the excellent de-NO_x activity but also the low SO₂ oxidation performance.     

TiO2基催化剂还原CO2研究进展

能源危机和环境污染是当今世界发展面临的两大挑战,如何有效缓解煤、石油等不可再生化石资源过度消耗所引发的能源危机,以及由此造成CO₂过量排放引起的温室效应问题,是当前人类发展亟待解决的重大科学问题之一。基于此,本文综述了近年来以TiO₂为光催化剂,以绿色、清洁的太阳光能催化还原CO₂成低价态含碳燃料(如CH₄、CH₃OH、HCHO、HCOOH、C₂H₅OH等)研究进展。在TiO₂光还原CO₂机理基础上,对元素掺杂、半导体复合与染料敏化、高活性晶面调控、低维纳米结构设计、助催化剂、Z型结构设计和单原子催化等方法来提高光还原CO₂反应效率和选择性进行分析,并指出目前研究存在的关键问题和未来CO₂光还原的发展方向。     

Catalytic wall reactor: Catalytic coatings of stainless steel by VOx/TiO2 and Co/SiO2 catalysts

Catalytic wall (structured) reactors and structured supports are suitable to study the catalytic properties of nanosized materials. The coating of metallic (aluminum and stainless steel) plates by thin layers of active phase is presented in two cases, VO_x/TiO₂ and Co/SiO₂, catalysts used in the oxidative dehydrogenation (ODH) of propane and in Fischer–Tropsch synthesis (FTS) of clean fuels, respectively. The preparation of coated plates and their characterisation by various methods of physicochemical analysis are described. Both chemical and physical methods were used for coating. VO_x/TiO₂ layers were obtained by grafting of Ti (on Al or stainless-steel plates) and V (on TiO₂) alkoxides and use of sol–gel media or suspension. A silica primer was deposited (on stainless-steel plate) by plasma-assisted chemical vapour deposition (PACVD) onto which Co oxide and silica were coprecipitated from sol–gel. The catalytic experiments in the respective reactions were carried out in special plate reactors and compared with those of catalytic powders. The study shows that the coating of a metallic substrate by a catalyst is not straightforward and requires specific studies dealing with both chemistry (chemical affinity between substrate and catalytic layers) and catalytic engineering (catalytic performance in taylor-made reactors).     

Au–TiO2 catalysts stabilised by carbon nanofibres

The catalytic activity and stability in the water–gas shift reaction have been tested for Au-based catalysts prepared by deposition of Au from colloid solutions. The supports that have been used are TiO₂, TiO₂ supported on carbon nanofibres (CNF) and CNF. Thermal treatments of the samples show that the Au particle size depends on the support material and hence the interaction between the Au particles and the support. In situ X-ray absorption spectroscopic (XAS) measurements during the water–gas shift reaction show no changes in the first Au–Au coordination number for the catalysts containing CNF. Furthermore, improved short-time stability is obtained compared to the AuTiO₂ catalysts. The improved stability is achieved by the CNF stabilising small TiO₂ particles and hence prevent subsequent sintering of the Au particles.     

The behaviour of Ru/Fe2O3 catalysts and Fe2O3 supports in the TPR and TPO conditions

The texture of Fe₂O₃ support and Ru/Fe₂O₃ catalysts supported on iron oxides obtained from β-FeOOH (B) or δ-FeOOH (D) and their catalytic activity in WGSR were studied. Also their susceptibilities to reduction and reoxidation, were studied by TPR, using H₂ or CO and TPO methods. In the case of TPR_CO the composition of the reducing mixture containing traces of H₂O enabled investigation of water gas shift reaction (WGSR).

The catalysts from series D were found more readily reducible and oxidised than those from series B. The supported ruthenium enhanced the redox effects and caused the appearance of additional effects related directly to its presence. Depending on the kind of support and on ruthenium presence considerable differences in temperatures of WGSR onset were found. It is suggested that the susceptibility of the catalysts to reduction and oxidation is responsible for their activity in the WGSR.     

水基纳米TiO_2路径制备有序介孔TiO_2-SiO_2及其可见光催化性能

在多巴胺修饰的水基TiO_2纳米微粒(TiO_2NPs)悬浮液中,以正硅酸乙酯为硅源,十六烷基三甲基溴化铵为模板剂,分别采用碱性水热方法或酸性溶胶-凝胶方法,制备了有序介孔TiO_2-SiO_2(TiO_2NPs/MCM-41或TiO_2NPs/SBA-3)。采用XRD、TEM、ICP和N2吸附-脱附实验对样品进行表征。结果表明,制备的介孔TiO_2-SiO_2在TiO_2高负载质量分数(23.98%TiO_2NPs/MCM-41、17.27%TiO_2NPs/SBA-3)时,仍能保持长程有序的介孔氧化硅结构。TiO_2NPs随机地嵌入在有序介孔氧化硅孔道所组成的网络结构中。在可见光下催化甲基橙降解反应中,反应时间120 min时,在P25上甲基橙相对浓度降为57%,在TiO_2NPs/MCM-41上降为33%,而在TiO_2NPs/SBA-3上降为5.7%。     

载体对V_2O_5-MoO_3/TiO_2催化剂表面性质及其选择性催化还原脱硝性能的影响

采用比表面积分别为101.86 m2·g-1(A)、86.37 m2·g-1(B)和7.78(C)m2·g-1(C)的TiO_2载体,通过分步浸渍法制备V2O5-Mo O3/TiO_2(A,B,C)选择性催化还原脱硝催化剂。在空速为10 000 h-1和氨氮体积比1.0条件下,以TiO_2(A)与TiO_2(B)为载体制备的催化剂脱硝活性在反应温度窗口(350~450)℃超过90%,且具有良好的高温抗硫中毒性能和相对较小的氨气氧化率。而以TiO_2(C)为载体制备的脱硝催化剂活性温度窗口窄,在350℃时获得的最高脱硝活性仅为73%,且对NH3的氧化作用较强。利用X射线衍射、低温N2吸附-脱附、紫外-可见漫反射光谱、H2程序升温还原和NH3程序升温脱附等对载体和催化剂进行表征。结果表明,活性组分V2O5在载体TiO_2(A)上分散性良好,主要以孤立态钒氧物种形式存在,因此,以TiO_2(A)为载体制备的催化剂比表面积、氧化还原性和表面酸性等性能更优。     

Hydrodesulfurization activity of CoMo and NiMo supported on Al2O3–TiO2 for some model compounds and gas oils

Catalytic activities of Al₂O₃–TiO₂ supporting CoMo and NiMo sulfides (CoMoS and NiMoS) catalysts were examined in the transalkylation of isopropylbenzene and hydrogenation of naphthalene as well as the hydrodesulfurization (HDS) of model sulfur compounds, conventional gas oil (GO), and light cycle oil (LCO). Al₂O₃–TiO₂ supporting catalysts exhibited higher activities for these reactions except for the HDS of the gas oil than a reference Al₂O₃ supporting catalyst, indicating the correlation of these activities. Generally, more content of TiO₂ promoted the activities. Inferior activity of the catalyst for HDS of the gas oil is ascribed to its inferior activity for HDS of dibenzothiophene (DBT) in gas oil as well as in model solvent decane, while the refractory 4,6-dimethyldibenzothiophene (4,6-DMDBT) in gas oil as well as in decane was more desulfurized on the catalyst. Characteristic features of Al₂O₃–TiO₂ catalyst are discussed based on the paper results.