正辛胺模板法制备Si／Al复合空心微球及其结构表征

以正辛胺为模板、正硅酸乙酯(TEOS)为硅源、异丙醇铝为铝源,在盐酸的催化作用下通过溶胶一凝胶方法制备出圆形度和分散性好、结构完整的Si/Al复合空心微球.分析了不同反应时间和反应温度下Si/Al复合空心微球的形貌、粒径、成分和结构.结果表明:Si/Al复合空心微球的平均粒径随反应温度和反应时间的增加而缓慢增大,但明显小于同样条件SiO2空心微球的粒径.Si/Al复合空心微球的平均粒径为8～16μm,壳层厚度为2.18～3.61μm.Si/Al复合空心微球中的铝主要以氧化物的形式存在;壳层表面具有微孔结构,比表面积为431～912 m2/g;可几孔径为1.2～2.0nm.     

表面化学沉积法制备SiO2空心微球

研究了以聚苯乙烯(PS)微球为模板,采用表面化学沉积技术制备SiO2@PS微球的工艺.利用ξ电位及FT-IR吸收光谱分析了硅烷偶联剂(MPS)及引发剂(KPS)对PS微球表面电荷及表面官能目的影响,在PS微球表面官能化过程中加入KPS,促进PS微球与MPS聚合,增加了微球表面Si-OH的浓度,实现TEOS在PS微球表面的均匀包裹,制得了单分散的核壳结构的SiO2@PS微球.通过调整TEOS的加入量,可得到壁厚在20～55nm的SiO2空心球.     

P(St-EA-MAA)模板法制备中空二氧化硅微球

以种子乳液聚合制得的P(St-EA-MAA)共聚物微球为模板,γ-氨丙基三甲氧基硅烷(APS)为助结构导向剂,正硅酸四乙酯(TEOS)为硅源,制备了P(St-EA-MAA)/SiO2复合微球,经高温煅烧除去聚合物模板,得到了中空二氧化硅微球。热重分析(TGA)表明模板剂的最佳脱除温度为600℃。高分辨透射电镜(HRTEM)观察显示所制得的二氧化硅微球具有典型的中空结构和良好的单分散性,其尺寸主要取决于共聚物微球的大小,通过调节微球模板的尺寸可以有效控制中空微球的大小。N2吸附-脱附曲线显示二氧化硅壁具有丰富的微孔,比表面积、平均孔径和孔容分别为117.87m2/g、1.98nm和0.21cm3/g。在制备复合微球的过程中加入一定量的CTAB可以调整中空微球的壁厚和壁的孔结构,使其比表面积、平均孔径和孔容增加到219.79m2/g、3.89nm和0.25cm3/g。     

核-壳式聚苯乙烯/二氧化硅复合微球及空腔硅球的制备

利用层层自组装的方法制备了粒径和组成可裁剪、具有核-壳式结构的单分散聚苯乙烯(PS)/二氧化硅(SiO₂)复合微球.对复合微球进行热处理除去有机物中心,制备出壁厚可剪裁的空腔硅球.透射电镜(TEM)照片显示二氧化硅纳米颗粒在中心外生成均匀壳层,而煅烧后则可得到轮廓分明的球形空腔;热重分析(TG)说明复合球体的硅含量随着所组装的纳米二氧化硅的粒径的增加而增加;比较PS、SiO₂、复合球体及热处理后的粉体的红外光谱,可分别验证二氧化硅的成功组装和热处理过程中作为中心的PS的完全去除.在吸附相同层的前提下,随着所选用的二氧化硅纳米粒子(10um,20um,40um)的粒径的增大,复合微球的粒径增大,空腔球体的壁厚增加.     

胶晶/嵌段共聚物双重模板制备多级孔材料

采用分段乳液聚合法和无皂乳液聚合法制备了聚苯乙烯(PS)微球,以此单分散胶态晶体和嵌段共聚物P123为模板剂,通过Y型分子筛前驱体的填充和模板剂的去除制备了具有大-介-微多级孔的材料.采用XRD、SEM和TEM等手段表征了PS微球及多级孔材料.结果表明,分段乳液聚合可以制备平均粒径为50nm的PS微球,无皂乳液聚合可以制备450nm左右的PS微球;以其作为大孔模板剂分别考察了PS微球粒径、模板剂用量、水用量等因素对多级孔材料合成的影响,结果表明,PS微球的粒径越大,材料中大孔的分散性越好.合成多级孔材料的条件为:PS微球乳液与前驱体的比值(质量比)为1.0~0.5,水与前驱体的比值为7.5,P123与前驱体的比值为0.1.     

中空TiO2微球的制备及其对聚丙烯酸酯薄膜保温性能的影响

以阳离子PS微球为模板, 钛酸四丁酯为钛源, 氨水为催化剂制备中空TiO₂微球, 通过物理共混法将中空TiO₂微球引入到聚丙烯酸酯薄膜中, 考察了中空TiO₂微球的空心粒径及用量对复合薄膜光反射性、导热系数及力学性能的影响。结果表明: 中空TiO₂微球的引入可显著提升聚丙烯酸酯薄膜的各项性能, 中空TiO₂微球的空心粒径和用量对复合薄膜的性能有不同程度的影响, 随着中空TiO₂微球空心粒径和用量的增加, 复合薄膜的性能基本呈现先提升后降低的趋势, 其中当中空TiO₂微球空心粒径为300 nm、用量为1%时, 所制备的复合薄膜保温性能和力学性能最优。     

二氧化钛空心微球的制备及表征

采用模板法制备了可控制球壳厚度的亚微米二氧化钛空心微球.首先利用钛酸四丁酯乙醇溶液和聚苯乙烯粒子制备了二氧化钛/聚苯乙烯复合粒子,在空气中经500℃煅烧除去苯乙烯模板后得到锐钛矿二氧化钛空心微球.透射电镜和扫描电镜观察表明,二氧化钛/聚苯乙烯复合粒子煅烧后体积发生了急剧的收缩,形成具有空心结构二氧化钛微球.电子衍射和X射线衍射分析可知空心微球的二氧化钛球壳为锐钛矿.实验发现当钛酸四丁酯与乙醇的体积比从120提高到110时,二氧化钛空心微球的球壳厚度从20～25 nm增加到45～50nm;以不同粒径的聚苯乙烯粒子作模板,可以得到不同内孔直径的二氧化钛空心微球,其内孔直径比聚苯乙烯模板直径小15%～20%.     

P(St-co-AA)聚合物模板法制备中空SiO2微球研究

以无皂乳液聚合法制备的苯乙烯(St)和丙烯酸(AA)阴离子型无规共聚物[P(St-co-AA)]微球为模板,不经过分离和离心、表面改性等任何后处理过程,采用溶胶-凝胶方法直接进行二氧化硅(SiO_2)包覆,成功制得中空SiO_2微球。探究了氨水用量、正硅酸乙酯(TEOS)用量以及不同AA用量对中空SiO_2微球的影响,并对制得的SiO_2微球进行了表征。研究结果表明,制得的中空SiO_2微球分散性优异,体系中无SiO_2实心小粒子,粒径均一,表面形貌呈树莓状,微球壁厚可控制在5～30nm范围内。     

单分散聚苯乙烯微球合成及在三维有序大孔材料制备中的模板作用

通过乳液聚合得到了单分散的聚苯乙烯(PS)微球乳液并通过阳离子破乳沉降法实现PS微球自组装,得到了紧密堆积的PS微球的胶体模板剂。向PS胶体模板的空隙填充硅溶胶,再通过焙烧去除模板得到三维有序大孔(3DOM)二氧化硅(SiO_2)材料。采用扫描电子显微镜、透射电子显微镜、红外和热重分析等对合成的3D大孔SiO_2材料进行表征。结果表明:使用粒径不同的PS微球作为模板,制得的3D大孔SiO_2材料的孔径在200~400nm之间。该制备方法为多孔材料的制备开拓了一条可行、便捷的途径。     

SiO2空心球的制备与表面形貌调控

以聚苯乙烯(PS)微球为模板,通过水解正硅酸乙酯来包裹PS微球,制备了PS/SiO_2核壳结构微球,然后通过高温煅烧得到SiO_2空心球。利用纳米粒度仪、扫描电子显微镜、透射电子显微镜分析SiO_2空心球的粒径和表面形貌。采用控制变量法分别研究了PS微球表面电荷、pH、水和正硅酸乙酯的用量对SiO_2空心球表面形貌的影响。实验证明,以表面带正电荷的PS微球为模板,反应体系pH=11.0,正硅酸乙酯注入速度为100μL/min时,制备的SiO_2空心球表面最光滑。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from     

CNAS Passes APLAC's PTP Review

正The review group of Asia Pacific Laboratory Accreditation Cooperation(APLAC)carried out a 4-day peer review of the proficiency testing provider(PTP)for China National Accreditation Service for Conformity Assessment(CNAS)from July 28 to 31,2014.CNAS passed the PTP review with excellent performance.Two senior peer reviewers of APLAC made a comprehensive,rigorous and detailed review of CNAS’s PTP accreditation activities,and made the on-spot inspection of the review groups in Shanghai and Shenzhen respectively.