室温直流磁控溅射制备ITO膜及光电性能研究

室温条件下,在玻璃衬底上,采用直流磁控溅射法制备了ITO膜.研究了溅射压强,氧流量和溅射功率等工艺参数对薄膜光电性能的影响.结果表明当Ar流量为44.2 sccm和溅射时间20 min等参数不变时,溅射气压0.7 Pa,氧流量0.62 sccm和溅射功率130 W为最佳工艺条件.并得到了电阻率5.02×10-4 Ω·cm,在可见光区平均透过率80%以上ITO薄膜.     

磁控溅射制备增透ITO薄膜及其性能研究

用射频磁控溅射法在低温下制备了光电性能优良的ITO(In2O3:SnO2=1:1)薄膜。质量流量计调节氩气压强PAr为0.2～3.0Pa,氧流量fO2为0～10sccm,并详细探讨了溅射时PAr和fO2变化对ITO薄膜光学性能的影响。结果表明:fO2的改变引起薄膜中氧空位浓度变化而影响ITO薄膜折射率n;fO2对ITO靶材表面的溅射阀值和对Ar 散射而改变溅射速率。衬底表面粗糙度对ITO薄膜的折射率测量准确性有较大影响。PAr为0.8Pa,fO2为2.4sccm,薄膜厚度为241.5nm时,nmin=1.97,最大透过率为89.4%(包括玻璃基体),方阻为75.9?/□,电阻率为8.8×10-4?·cm。AFM分析表明薄膜表面针刺很少,表面平整(RMS=3.04nm)。     

磁控溅射制备ITO薄膜光电性能的研究

采用直流磁控溅射方法在玻璃基底上制备了ITO薄膜.分别用分光光度计和四探针仪测试了所制备ITO薄膜在可见光区域内的透过率和电阻率,研究了溅射气压、氧氩流量比和溅射功率三个工艺参数对ITO薄膜光电性能的影响.研究结果表明,制备ITO薄膜的最佳工艺参数为:溅射气压0.6 Pa,氧氩流量比1:40,溅射功率108 W.采用此工艺参数制备的ITO薄膜在可见光区平均透过率为81.18％,薄膜电阻率为8.9197×10-3Ω·cm.     

气流场强度对直流磁控溅射ZAO薄膜性能的影响

用含2%Al的Zn/Al合金靶材,在不同气流场强度下使用直流反应磁控溅射法在玻璃衬底上制备了ZAO(ZnO:Al)透明导电薄膜样品.定义气流场强度等于总气流量除以总气压.结果表明:气流场强度的大小对ZAO薄膜的表面形貌和电导率有较大影响,对可见光的透射率影响不大.在Ar气压强为0.3Pa,流量为22sccm,O2气压强为0.08Pa,流量为10sccm,气流场强度约为84sccm/Pa时制备ZAO薄膜的最低电阻率为4.2×10-4Ω·cm,可见光透射率为90%.     

直流反应磁控溅射法制备太阳电池用ITO透明导电膜

采用直流反应磁控溅射法制备了ITO透明导电薄膜,针对氧流量、溅射气压、溅射电流3种工艺参数对ITO薄膜电阻率和可见光区透射率的影响进行了分析和研究。结果表明:从ITO薄膜作为太阳电池用减反射层和电极出发,得到了工艺参数的优化值,分别为氧流量0.2 ml/min(标准状态),溅射气压3 Pa和溅射电流0.2 A,ITO薄膜的电阻率为3.7×10-3Ω.cm,透过率(550 nm)高达93.3%。另外,利用该优化工艺条件下制备的ITO薄膜作为电极和减反射层,制备了结构为ITO/n+-nc-Si∶H/-i nc-Si:H/p-c-Si/Ag的太阳能电池,电池开路电压Voc达到534.7mV,短路电流Isc达到49.24mA(3 cm2),填充因子为0.4228。     

磁控溅射TiN薄膜的工艺及电学性能研究

采用反应直流磁控溅射法,在Si基底上制备TiN薄膜.研究了溅射沉积过程中溅射气压和Ar/N2气体流量比对TiN薄膜结构及其电学性能的影响,并对试验结果进行了分析.研究发现,在Ar/N2气体流量比为15:1时,TiN薄膜的表面均方根粗糙度和电阻率都为最小.当溅射气压增大时,薄膜厚度减小.当溅射气压为0.3～0.5Pa时,薄膜表面较光滑,电阻率较小.     

倾斜磁控溅射制备低阻高透ITO薄膜及其光电特性

利用直流磁控溅射方法,在Ar和O_2的混合气氛中,采用陶瓷靶制备ITO薄膜;采用紫外-可见-红外分光光度计和四探针法研究了溅射工艺参数对ITO薄膜的光电特性的影响。实验结果表明,当靶材角度在23-25°、O_2流量在7-9sccm、溅射时间在60-90 min和溅射功率在100-120W时获得可见光透过率高于90%,方阻在10-20Ω/□之间的优质ITO薄膜。     

Ar气氛下直流磁控溅射ITO薄膜的结构和性能

采用直流磁控溅射法在低温、100%Ar的无氧气氛中制备了光电性能优良的铟锡氧化物(ITO,In2O3:SnO2=90:10,质量百分比)薄膜,详细探讨了溅射时改变氩气压强对ITO薄膜结构以及光电性能的影响.结果表明:溅射时氩气压强越小,ITO薄膜的体心立方晶型越完整,导电性越好,但对可见光透过性的影响不大.当氩气压强为0.3Pa时,溅射薄膜性能最佳,其光透过率可达92.9%,电导率为8.9×10-4Ω·cm.     

ITO靶材的直流磁控溅射镀膜工艺研究

对ITO靶材的直流磁控溅射工艺进行研究,通过正交试验方法确定制备ITO薄膜的最优工艺参数,并明确了溅射温度、氧氩比、溅射气压和溅射功率密度对ITO薄膜电阻率和可见光透过率的影响规律。最优工艺参数为溅射温度370℃,氧氩比0.5/40,溅射气压0.4 Pa,溅射功率密度0.17 W/cm~2。薄膜电阻率受各因素影响的主次顺序是:氧氩比溅射温度溅射气压溅射功率密度。薄膜可见光透过率受各因素影响的主次顺序为:溅射温度溅射气压氧氩比溅射功率密度。     

反应磁控溅射法制备F掺杂ZnO(FZO)薄膜的结构和透明导电性能

以Zn/ZnO/ZnF2混合物为靶材,在衬底温度(Ts)为150℃和300℃、溅射气氛为Ar+O2和Ar+H2下反应溅射制备F掺杂ZnO(FZO)薄膜,研究气体流量、Ts以及溅射气氛对薄膜结构及透明导电性能的影响.结果表明:对于Ar+O2下制备的FZO薄膜,Ts=300℃时有利于制备出具有(002)择优取向、结晶度高、压应力低且透明导电性能较好的薄膜.对于Ar+H2下制备的薄膜,Ts增大到300℃虽然提高了薄膜结晶度和透光性,降低了压应力,但薄膜厚度明显降低,薄膜导电性能变差.比较两种气氛下制备的FZO薄膜,发现Ar+H2下制备的薄膜可在150℃和0.8～3.2 mL·min-1的H2流量范围内得到更好的透明导电性能(电阻率为3.5×10-3Ω·cm,可见光平均透光率为87％).讨论Ar+H2气氛时H等离子的刻蚀作用与H掺杂、A r+O 2气氛时O离子的轰击作用与薄膜氧缺陷的变化、Ts升高时沉积原子反应活性与迁移能力增强以及Eg与载流子浓度的关系.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...