不同预处理方式与微滤联用处理城市污水对比实验研究

采用微滤法处理模拟二沉池出水,以期达到城市污水回用的目的.进水采用人工配水,主要考察微滤膜对模拟二沉池出水中CODMn,氨氮(NH3-N)及UV254的去除效果,以及预处理方式对微滤膜处理工艺的影响.实验主要采用了两种预处理方式,即颗粒活性炭(GAC)吸附及聚合氯化铝(PAC)混凝.实验结果表明,单独采用微滤膜效果不明显,高锰酸钾指数的去除率仅为32.5%,氨氯去除率约为5%,且膜污染严重,通量下降很快.活性炭-微滤组合工艺对污水的CODMn去除效果较好,去除率达到88%;而混凝-徽滤工艺对UV254的去除效果较好,去除率达到87%;混凝-微滤及活性炭-微滤工艺对氨氮的去除率均不高.组合工艺比起单独使用微滤膜流量下降缓慢,混凝-徽滤工艺在4.5h内,流量没有下降,污染情况明显改善.     

Comparison of electrocoagulation, coagulation and the fenton process for the treatment of reactive dyebath effluent.

In this paper, experimental studies were performed on a simulated reactive dyebath effluent to compare coagulation-flocculation and Fenton's oxidation with electrocoagulation using stainless steel (SS 304) and aluminium electrodes in terms of colour and COD removals as well as AOX formation potential and improvement of biological treatability. Results have indicated that FeCl3 and alum coagulation had little effect on colour removal whereas comparable colour removal efficiencies with those of electrocoagulation with steel electrodes and Fenton's oxidation were attained by FeSO4 coagulation. Almost complete colour removals accompanied with 77% COD abatement were obtained by both electrocoagulation with steel electrodes and Fenton's oxidation under optimised reaction conditions. Although electrocoagulation with aluminium electrodes yielded very limited colour removal and produced a high amount of sludge upon extended reaction time, this application brought about a marked improvement in biodegradability.     

Simultaneous optimization of multiple performance characteristics in coagulation-flocculation process for Indian paper industry wastewater

The goal of this study was to optimize the coagulation-flocculation process in wastewater generated from the paper and pulp industry using a grey relational analysis (GRA)-based Taguchi method. Process parameters included types and doses of natural coagulants and coagulant aid, and pH. To track the efficiency of the treatment process, the following responses were chosen for optimization: chemical oxygen demand (COD), total dissolved solids (TDS) and turbidity of wastewater, alone or in combination or all together. Analysis of variance showed that the type and dose of the coagulant aid were the most significant parameters, followed by pH and the dose of the coagulant; the type of coagulant used was found to be insignificant in the coagulation-flocculation process. Optimization of process parameters to achieve lower turbidity and greater removal of COD and TDS was verified in a separate confirmatory experiment, which showed improvements in COD and TDS removal and a decrease in turbidity of 8.2, 6.35 and 26.17%, respectively, with the application of the Taguchi method and GRA.     

Pretreatment and biotreatment of saline industrial wastewaters.

Wastewater from an Akzo Nobel production site contains more than 50 g/l total dissolved salts, mainly chlorides and sulphates, and is currently being treated after 10-20 x dilution. Biological treatment of undiluted or less diluted wastewater is very desirable for environmental and economic reasons. Possibilities were investigated in laboratory scale reactors to treat this highly saline and high strength wastewater aerobically, either after long adaptation or after removing part of the salts by a pretreatment. Adaptation and selection from mixed activated sludge populations took approximately 40 days to finally achieve a COD removal in aerobic treatment of 55-65% at two times dilution (11-16 g/l chloride and 5-7 g/l sulphate). Undiluted wastewater was not treatable. A higher removal percentage (> 80%) was possible at the original high salt concentration only when the sludge load was limited to approximately 0.4-0.5 kg COD/kg sludge/day. A longer adaptation time was required. Nanofiltration (NF) and crystallization could be used as a pretreatment to remove and recover up to 80% of the sulphate in the form of crystallized Glauber salt. Recovery strongly depended on the sulphate and chloride concentration in the NF concentrate and on crystallization temperature. The salt (sulphate) reduction through the NF improved the removal efficiency of a consecutive biotreatment only at a relatively low chloride level, demonstrating that the combination of nanofiltration-crystallization-aerobic biodegradation is less feasible for very saline wastewaters. Anaerobic pretreatment of saline waters turned out to be rather sensitive to high salinities. Only wastewater diluted to 10 g/l chloride could be treated well: sulphate concentration decreased by 80% and COD by 40%. Removal efficiencies of the combined anaerobic-aerobic treatment were approximately 80-85%, proving that this was a feasible route for 2-3 x diluted wastewater. The study has shown that several alternatives are available for treatment of the very saline wastewaters at a much lower degree of dilution than currently practiced.     

Use of agro-food wastewaters for the optimisation of the denitrification process.

The aim of this work was to study the feasibility of the denitrification process enhancement, in the Ciudad Real (Spain) WWTP, by dosing agro-food wastewaters generated nearby the city. The studied agro-food wastewaters were characterised by a high COD and low nutrients concentration. The denitrification rates with these wastewaters were lower than those obtained either with acetate or urban sewage, however the dose of agro-food wastewaters raised significantly the denitrification capacity in the WWTP because of the significant increase of easily biodegradable substrates in the wastewater. From the laboratory NUR batch test it was observed that the best agro-food wastewater to enhance the denitrification process was that coming from tomato processing, which presented an average denitrification rate of 1.9 mg NOx-N/(g VSS.h) and an average denitrification yield of 0.2 mg NOx-N/mg COD. The viability of the use of tomato processing wastewater was checked in a pilot plant optimised for urban sewage treatment with biological nutrient removal. The optimum dose, 5.9 mg COD/mg NOx-N, was applied and 99% of the nitrate was removed from the wastewater without influencing negatively either the COD or P effluent concentrations.     

Aerobic granulation in a sequencing batch reactor (SBR) for industrial wastewater treatment.

Aerobic granulation seems to be an a attractive process for COD removal from industrial wastewater, characterised by a high content of soluble organic compounds. In order to evaluate the practical aspects of the process, comparative experimental tests are performed on synthetic and on industrial wastewater, originating from pharmaceutical industry. Two pilot plants are operated as sequencing batch bubble columns. Focus was put on the feasibility of the process for high COD removal and on its operational procedure. For both wastewaters, a rapid formation of aerobic granules is observed along with a high COD removal rate. Granule characteristics are quite similar with respect to the two types of wastewater. It seems that filamentous bacteria are part of the granule structure and that phosphorus precipitation can play an important role in granule formation. For both wastewaters similar removal performances for dissolved biodegradable COD are observed (> 95%). However, a relatively high concentration of suspended solids in the outlet deteriorates the performance with regard to total COD removal. Biomass detachment seems to play a non-negligible role in the current set-up. After a stable operational phase the variation of the pharmaceutical wastewater caused a destabilisation and loss of the granules, despite the control for balanced nutrient supply. The first results with real industrial wastewater demonstrate the feasibility of this innovative process. However, special attention has to be paid to the critical aspects such as granule stability as well as the economic competitiveness, which both will need further investigation and evaluation.     

SBR treatment of olive mill wastewaters: dilution or pre-treatment?

The olive-oil extraction industry is an economically important activity for many countries of the Mediterranean Sea area, with Spain, Greece and Italy being the major producers. This activity, however, may represent a serious environmental problem due to the discharge of highly polluted effluents, usually referred to as 'olive mill wastewaters' (OMWs). They are characterized by high values of chemical oxygen demand (COD) (80-300 g/L), lipids, total polyphenols (TPP), tannins and other substances difficult to degrade. An adequate treatment before discharging is therefore required to reduce the pollutant load. The aim of the present paper was to evaluate performances of a biological process in a sequencing batch reactor (SBR) fed with pre-treated OMWs. Pre-treatment consisted of a combined acid cracking (AC) and granular activated carbon (GAC) adsorption process. The efficiency of the system was compared with that of an identical SBR fed with the raw wastewater only diluted. Combined AC and GAC adsorption was chosen to be used prior to the following biological process due to its capability of providing high removal efficiencies of COD and TPP and also appreciable improvement of biodegradability. Comparing results obtained with different influents showed that best performances of the SBR were obtained by feeding it with raw diluted OMWs (dOMWs) and at the lowest dilution ratio (1:25): in this case, the removal efficiencies were 90 and 76%, as average, for COD and TPP, respectively. Feeding the SBR with either the pre-treated or the raw dOMWs at 1:50 gave very similar values of COD reduction (74%); however, an improvement of the TPP removal was observed in the former case.     

Oxidative processes for olive mill wastewater treatment.

The present work describes an experimental study carried out in order to investigate the efficiency and feasibility of physical (lime coagulation) and advanced oxidation processes (Ozone and Fenton's process) for olive oil mill wastewater treatment. Particular attention was paid to the degradation of both organic and phenolic compounds. Lime coagulation reaches maximum removal at a pH of 12, with a TP (total polyphenols) and COD reduction of 37 and 26%, respectively. Ozone oxidation is also pH-dependent, showing the higher removal efficiency (91% for TP and 19% for COD) with an initial pH value of 12. Experimental results show a lower efficiency of Fenton's process than ozone in TP removal, reaching a maximum value of 60%. Oxidation trials carried out on gallic and p-coumaric synthetic solutions confirmed ozone and Fenton's efficiency at degrading phenolic compounds. Biological trials, both aerobic and anaerobic, highlighted a significant increase of biodegradability of treated OMW samples if compared to the untreated ones. Respirometric tests showed an increase in BOD of about 20% and anaerobic batch tests provided a methane production up to eight times higher.     

Treatment of slaughterhouse plant wastewater by using a membrane bioreactor

The use of a membrane bioreactor (MBR) for removal of organic substances and nutrients from slaughterhouse plant wastewater was investigated. The chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) concentrations of slaughterhouse wastewater were found to be approximately 571 mg O2/L, 102.5 mg/L, and 16.25 mg PO4-P/L, respectively. A submerged type membrane was used in the bioreactor. The removal efficiencies for COD, total organic carbon (TOC), TP and TN were found to be 97, 96, 65, 44% respectively. The COD value of wastewater was decreased to 16 mg/L (COD discharge standard for slaughterhouse plant wastewaters is 160 mg/L). TOC was decreased to 9 mg/L (TOC discharge standard for slaughterhouse plant wastewaters is 20 mg/L). Ammonium, and nitrate nitrogen concentrations of treated effluent were 0.100 mg NH4-N/L, and 80.521 mg NO3-N/L, respectively. Slaughterhouse wastewater was successfully treated with the MBR process.     

Effect of Fenton's treatment on the biodegradability of chromium-complex azo dyes.

Pretreatment of an acid dyebath effluent bearing a new generation chromium complex azo dyestuff (C0 = 350 mg/L) with Fenton's reagent was investigated. Preliminary optimisation (baseline) experiments were conducted to determine the Fe2+, H2O2 concentrations and pH required to the highest possible COD and colour removals. Kinetic studies were carried out at varying temperatures (20 degrees C < T < 70 degrees C) to establish a relationship between COD abatement and H2O2 consumption. The activation energy found for catalytic H2O2 decomposition (Ea = 9.8 kJ/mol) appeared to be significantly less than that of fermentative (Ea = 23 kJ/mol) and of thermal (Ea = 76 kJ/mol) H2O2 decomposition, implying that H2O2 decomposition during the Fenton's reaction occurs more spontaneously. The experimental studies indicated that approximately 30% COD and complete colour removal could be achieved under optimised Fenton pretreatment conditions (Fe2+ = 2 mM; H2O2 = 30 mM; pH = 3; at T = 60 degrees C). Long-term activated sludge experiments revealed that although the raw and pretreated acid dyebath effluent contained practically the same amount of "readily biodegradable" COD (inert COD fraction < or = 10%), biodegradation of the chemically pretreated acid dye effluent proceeded appreciably faster than that of the untreated acid dyebath effluent.     

The removal of residual organic matter from biologically treated swine wastewater using membrane bioreactor process with powdered activated carbon.

The objective of this study was to characterize the mechanisms of the COD removal in the membrane bioreactor (MBR) process with powdered activated carbon (PAC) addition and to determine its optimal operation, for the removal of residual organic matters (ROM) from biologically treated swine wastewater. The MBR process with PAC showed higher removal efficiency of chemical oxygen demand (COD(Mn)) than that without PAC. When the average COD(Mn) concentration of the influent was 217 mg/L, the average COD(Mn) concentration of the permeate from the MBR with PAC was about 41.5 mg/L, indicating an approximate removal efficiency of 81%. On the other hand, the average COD(Mn) concentration of the permeate from the MBR without PAC was 172 mg/L. The PAC dosage estimated to obtain the above removal efficiency was about 0.74 g per litre of influent. Among the total residual organics removed by PAC-added MBR, 46.5% was removed by PAC adsorption, 20.8% by biodegradation, 4.4% by membrane separation, and 9.3% by enhanced microorganism activity. From these results, the MBR process with PAC was considered as a very useful treatment process for the reduction of COD(Mn) in biologically treated swine wastewater.     

Treatment of oilfield wastewater by Fenton's process.

A combination of coagulation and Fenton's process was used for the removal of total oxygen carbon (TOC) from oilfield wastewater. Compared with aluminium sulfate, ferric coagulant had better TOC removal efficiency at the same mass dosage. In Fenton's process, the effect of H2O2 and Fe2+ dose on the removal of TOC was studied. The optimum conditions required for TOC removal were an Fe3+ concentration of 40-50 mg/L, an H2O2 dose of 50 mmol/L and an Fe2+ concentration of 1.0 mmol/L. GC-MS chromatographic analysis indicated that most of the alkyl hydrocarbons of carbon numbers < 21 were removed in the first minute of Fenton's process mainly through adsorption. Alkyl hydrocarbons and phenols were oxidized almost completely following 120 min of treatment. The pathway of newly formed intermediates in Fenton's process was proposed on the basis of the GC/MS chromatogram.     

超声波-好氧生物接触法处理制药废水

试验研究超声波-好氧生物接触法处理制药废水CODCr去除效果.结果表明在超声波处理时间60 s,功率200W时,制药废水单独经超声波处理,CODCr去除率仅为13%～16%;对好氧生物接触反应器中零时刻的混合液澄清水,直接进行好氧生物接触处理,CODCr去除率仅30%左右;而经超声波预处理后再好氧生物接触处理CODCr总去除率达到96%以上.经超声波预处理后,好氧生物接触最佳反应时间为12 h.     

Treatment of winery wastewater in a conventional municipal activated sludge process: five years of experience.

A full-scale wastewater treatment plant where municipal and winery wastewaters were co-treated was studied for five years. The experimental results showed that suspended solids, COD, nitrogen and phosphorous were effectively removed both during the treatment of municipal wastewater and the cotreatment of municipal and winery wastewater. The sludge production increase from 4 tons to 5.5 tons per day during the harvesting and wine making period. In any case the specific sludge production was 0.2 kgMLVSS per kgCOD(removed) despite the organic loading increasing. About 70% of the COD was removed through respiration. Also the energy demand increased from 6,000 to 7,000 kWh per day. The estimated costs for the treatment of the winery wastewater was 0.2-0.3 Euros per m3 of treated wastewater. With reference to the process efficiency, the nitrogen removal was just 20%. The co-treatment of municipal and winery wastewater in conventional activated sludge processes can be a feasible solution for the treatment of these streams at relatively low costs.     

活性炭吸附技术与树脂吸附技术处理DIBP废水的对比

采用活性炭吸附技术和树脂吸附技术进行增塑剂DIBP生产废水处理对比试验。结果表明:NDA-66树脂对邻苯二甲酸的吸附效果最好,去除率达93.9%,其次为椰壳活性炭,对增塑剂DIBP生产废水中COD和邻苯二甲酸的去除率分别为57.3%和83%,煤质和果壳活性炭的废水处理效果较差,对COD和邻苯二甲酸的去除率均在20%左右,且活性炭吸附不具有选择性,无法对邻苯二甲酸进行回收,不能产生相应的经济效益。而采用NDA-66树脂吸附处理增塑剂DIBP生产废水,其污染物削减量是活性炭吸附的4~5倍,回收邻苯二甲酸可产生110.8万元/a的经济效益,同时树脂脱附再生容易,可重复利用2年左右,因而具有更大的推广应用价值。     

Pretreatment of silk-dyeing industrial wastewater by UASB reactor.

The objective of this study was to investigate the performance of the upflow anaerobic sludge blanket (UASB) reactor as the pretreatment system for silk-dyeing wastewater. Two laboratory-scale UASB reactors, with working volume of 15.59 I, were used during May 1998 to June 1999. The actual wastewater was diluted to reduce ammonium ion toxicity on anaerobic bacteria. The experiments were conducted at the organic loading rates (OLRs) of 0.52, 1.01, 1.04, 1.54 and 2.56 kgCOD/(m3 x d), treating only wastewater generated from the acid-dye process of mixed-species raw silk. It took approximately 4 1/2 months to reach the steady-state conditions. It was found that the COD removal was in the ranges of 74.1-85.3%, except at OLR 2.56 kgCOD/(m3 x d) where efficiency significantly dropped to 55.2%. The apparent color removal was in the similar trend as COD. During the study periods, wastewater input had various color shades while the effluent generally looked pale yellowish. The methane generation rates ranged from 0.18-0.31 m3/kg COD removed, with methane composition 81.0-88.1% in biogas. The average granule size in the sludge bed had slowly increased to 0.73 mm in the last experiment. It can be concluded that the UASB reactor is suitable as a pretreatment system for silk-dyeing wastewater. An OLR of 1 kgCOD/(m3 x d) and an influent concentration diluted to 2,600 mgCOD/l are suggested while COD and apparent color removal efficiency of 80% and 70%, respectively, can be expected.     

Microbial fuel cells for wastewater treatment.

Microbial fuel cells (MFCs) are emerging as promising technology for the treatment of wastewaters. The potential energy conversion efficiencies are examined. The rates of energy recovery (W/m3 reactor) are reviewed and evaluated. Some recent data relating to potato-processing wastewaters and a hospital wastewater effluent are reported. Finally, a set of process configurations in which MFCs could be useful to treat wastewaters is schematized. Overall, the MFC technology still faces major challenges, particularly in terms of chemical oxygen demand (COD) removal efficiency.     

Effect of chemical treatment on the acute toxicity of two commercial textile dye carriers.

In the present experimental study, the effect of chemical treatment (coagulation-flocculation) on the acute toxicity exerted by two commercial dye carriers (called Carrier A and B herein) often used in the textile industry was investigated. Two different test organisms were selected to elucidate the situations in activated sludge treatment systems (activated sludge microorganisms) as well as in receiving water bodies (ultimate marine discharge). According to the results of a comprehensive analysis covering COD removal efficiencies, sludge settling characteristics and operating costs involved in coagulation-flocculation, the optimum treatment conditions were defined as follows; application of 750 mg/L ferrous sulphate at a pH of 9.0 for Carrier A; and application of 550 mg/L ferrous sulphate at a pH of 9.0 for Carrier B. The acute toxicities of both dye carriers towards marine microalgea Phaeodactylum tricornutum could be reduced significantly after being subjected to coagulation-flocculation. Fair toxicity removals (towards heterotrophic mixed bacterial culture accommodated in activated sludge treatment) were obtained with coagulation-flocculation for both of the carriers under investigation.     

电絮凝处理黄土塬地区村镇集蓄雨水的实验研究

采用电凝聚对黄土塬地区村镇集蓄雨水进行处理。通过改变极板间距、极板电压、电解时间,进行了对集雨水中COD,浊度,NH3-N,UV254的去除率研究。结果表明：电解时间15 min,极板间距为10 mm,极板电压为15 V的条件下,电絮凝对集蓄雨水中浊度、氨氮、UV254、COD有较好的去除效果,去除率分别为95%、63%、48%、80%,高于化学絮凝的处理效果。     

Activation of solgel titanium nanofilm by UV illumination for NOM removal.

The control of natural organic matter (NOM) in drinking water treatment plants is required in order to control (i) the formation of potentially harmful disinfection byproducts (DBPs), (ii) the regrowth of bacteria and (iii) pipe corrosion in the distribution system. Photocatalysis is a promising advanced oxidation technology due to its ability to mineralise chlorinated byproduct precursors such as humic acids (HAs) to carbon dioxide and water. In this study, the efficiency of HAs and NOM removal in terms of UV absorbance at 254 nm (UV254) was tested by means of a new photocatalytic reactor made of stacked polymethylmethacrylate (PMMA) rings coated by TiO2 nanofilm. Three different sets of rings were coated with TiO2 gel one, two and three times respectively to optimise the coating thickness according to UV254 removal efficiency. The titania sol was immobilised on the substrate by a low temperature procedure and after 8 months the reactors were reactivated by means of UV radiation before the experiments. The photocatalytic removal efficiency of humic acid in terms of UV254 was significantly higher after 1 hour for the reactor employed with high thickness TiO2 nanofilm (around 20%) compared to middle and low thickness reactors (6 and 1.4%, respectively). However, during the same reaction time only 10% of UV254 was removed with high thickness TiO2 nanofilm using raw surface water, probably owing to ionic species naturally occurring in the raw water sample. Finally, the activation of the TiO2 nanofilm may be effectively accomplished by means of UV radiation where calcination cannot be applied (e.g. thermally sensitive substrates).