Photoinduced grafting of acrylamide onto polyethylene film by means of two-step method

Benzophenone-coated low-density polyethylene (LDPE) was grafted with acrylic acid (AA), methacrylic acid (MA), acrylonitrile (AN), and methyl methacrylate (MMA) in an aqueous medium by photoirradiation. The first-step graft samples thus prepared with a grafting of about 50% were subjected to second-step photografting with acrylamide (AAm). On AA- and MA-grafted LDPE samples, the second-step grafting of AAm was very smooth, and a high level of grafting up to 800% was attained with ease. On the other hand, grafted LDPE samples employing hydrophobic monomers, AN and MMA, had a lower percent of grafting than those with hydrophilic monomers, AA and MA. By ESR study, a thermally stable radical was found in the first-step graft sample irradiated with light of λ > 330 nm. Mechanisms for the formation of such a radical in the first-step graft sample are proposed, and the contribution of the radical to the second-step grafting is discussed.     

Synthesis of polymer‐grafted natural rubbers by radical photopolymerization of vinyl monomers initiated from the rubber chains

The synthesis of polymer‐grafted natural rubbers (NRs) was considered through photopolymerization of vinyl monomers initiated from N,N‐diethyldithiocarbamate groups previously introduced onto cis 1,4‐polyisoprene units of NR chains. The development of the procedure was made with methyl methacrylate (MMA) as monomer. First, initiation of MMA photopolymerization was tested using a model molecule of the N,N‐diethyldithiocarbamate‐functionalized 1,4‐polyisoprene unit to verify the feasibility of the procedure considered. Then, MMA polymerization was successfully initiated from N,N‐diethyldithiocarbamate‐functionalized NR backbone used as macroinitiator, and the conditions of grafting were optimized. It was shown that MMA grafting could occur either in monomer medium, in solution in toluene, and in latex medium, and that the quantities of homopolymer formed were still low. Thereafter, grafting studies were performed with other vinyl monomers (styrene, methacrylonitrile, acrylamide, acrylic acid) showing that grafting efficiency depends essentially on the nature of the monomer. The method developed here was shown particularly well adapted for the synthesis of polymer‐grafted NR with monomers of low polarity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

丙烯酸酯乳液胶粘剂的合成及其性能研究

以丙烯酸丁酯(BA)、甲基丙烯酸甲酯(MMA)、苯乙烯(St)、丙烯腈(AN)和丙烯酸(AA)为单体,十二烷基硫酸钠(SDS)为乳化剂,过硫酸钾(KPS)为引发剂,通过半连续乳液聚合方法合成了丙烯酸酯乳液胶粘剂。研究了软硬单体配比、不同硬单体以及功能单体AA对胶粘剂性能的影响。研究结果表明,当m(BA)∶m(MMA)∶m(AN+St)=75∶15∶10[其中m(AN)∶m(St)=1∶3]、w(AA)=2份时,制备的乳液胶粘剂具有较好的剪切强度、拉伸强度和耐水性。     

悬浮接枝共聚合成POE-g-MAS及其对SAN树脂的增韧作用

合成了乙烯-辛烯共聚物(POE)和甲基丙烯酸甲醋(MMA)-丙烯腈(SAN)-苯乙烯(St)的接枝共聚物(POE-g-MAS)。研究了单体比率、POE/单体比率和引发剂浓度等因素对接枝共聚合反应的影响。聚合产物用丙酮抽提得到接枝共聚物POE-g-MAS,傅里叶变换红外光谱分析证明MMA-AN-St已经接枝在POE分子链上。用POE-g-MAS与Stet树脂共混制备了具有高抗冲性能的POE-g-SAN/SAN共混物,并用扫描电镜观察共混物的冲击断面,探讨了其增韧机理。     

中空聚合物乳液的制备及其性能研究

以甲基丙烯酸甲酯(MMA)、丙烯酸(AA)、丙烯酸丁酯(BA)、丙烯腈(AN)和苯乙烯(St)为共聚单体,过硫酸铵(APS)为引发剂,十二烷基硫酸钠(SDS)和非离子型乳化剂(OP-10)为阴/非离子型复合乳化剂,采用种子乳液聚合法和碱溶胀后处理法制备了P(MMA/AA/BA)为核、P(St/AA/AN)为壳的纸张施胶用中空聚合物乳液。研究结果表明:当w(引发剂)=0.80%、m(SDS)∶m(OP-10)=2∶1和w(乳化剂)=1.5%时,中空乳液的综合性能较好,其单体转化率较高、乳液黏度适中、粒径较小且分布较窄。     

Photografting of PVC containing N,N‐diethyldithiocarbamate groups with vinyl monomers

Poly(vinyl chloride) (PVC) with pendent N,N‐diethyldithiocarbamate groups (PVC–SR) was prepared through the reaction of PVC with sodium N,N‐diethyldithiocarbamate (NaSR) in butanone and used as a photoinitiator for the grafting polymerization of three vinyl monomers [styrene (St), methyl methacrylate (MMA), and acrylamide (Am)]. The effects of ultraviolet (UV) irradiation time, PVC–SR amount, and the monomer amount on grafting and grafting efficiency were investigated. The results showed that PVC–SR could initiate the polymerization of three vinyl monomers effectively and obtained crosslinked copolymers. The grafting and grafting efficiency of styrene and methyl methacrylate were higher than those of acrylamide. The polymerization activity of three monomers was acrylamide > methyl methacrylate > styrene. By analyzing the UV spectrum of PVC–SR with a different irradiation time, it was confirmed that PVC–SR was dissociated mainly into macromolecular the sulfur radical PVC–S · and the small molecular carbon radical · C(S)N(C₂H₅)₂; the grafting polymerization mechanism was discussed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2569–2574, 2000     

Emulsifier‐minor emulsion copolymerization of BA‐MMA‐St‐MAA (or AA)‐N‐MA

A novel emulsion polymerization technique referred to as emulsifier‐minor emulsion polymerization was achieved by the copolymerization of methyl methacrylate, butyl acrylate, and styrene (MMA‐BA‐St) with a combination of water‐soluble ionic monomers [methacrylic acid (MAA) or acrylic acid (AA)] and nonionic monomers (N‐methylol acrylamide). In the technique, water‐soluble monomers play a crucial role in the stabilization of the latex particles as they can be bound to the particle surface and form a hydrate protective layer, which exhibits steric and/or electrostatic effects to prevent particle coagulation. The minor but over its critical micelle concentration emulsifier sodium alkylated diphenyl ether disulfonate (DSB) results in the nucleation of particles mainly by the micelle nucleation mechanism and thus determines the polymerization rate, the particle size, and the number. The film water resistance of the latices can be improved, and the foaming capacity of can be lowered by using technique instead of conventional emulsion polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2923–2929, 2004     

反应性乳化剂对苯丙乳液合成及性能的影响

在反应性阴离子乳化剂[甲基丙烯酸羟丙磺酸钠(HPMAS)]的作用下,采用甲基丙烯酸甲酯(MMA)、苯乙烯(St)、丙烯酸丁酯(BA)和丙烯腈(AN)为主单体,丙烯酸(AA)为功能性单体,合成了性能优异的无皂苯丙乳液。研究了软硬单体配比、乳化剂、链转移剂和引发剂用量对乳液性能的影响。研究结果表明,合成无皂苯丙乳液的适宜条件(相对于单体总质量而言)是:w(HPMAS)=4%,w(引发剂)=0.8%,w(链转移剂)=2%且前期加入。     

Epoxidation,hydroxylation, acrylation and urethanation of Linum usitatissimum seed oil and its derivatives

Some preliminary studies on epoxidation, hydroxylation, acrylation and urethanation of Linum usitatissimum seed oil (LO) and its derivatives have been carried out. Epoxidation and hydroxylation were performed in situ using H₂O₂ and acetic acid to develop epoxidized oil (LOE) and epoxy polyol (EP). EP was modified with synthetic monomers, viz. acrylonitrile (AN) and methylmethacrylate (MMA), in the presence of benzoyl peroxide in an inert environment to develop acrylic grafted epoxy polyols (AEPs). EP and AEPs were further treated with an isocyanate, resulting in the formation of plain and acrylic grafted epoxy polyurethanes (EPU and AEPUs). The mechanism of the reaction as well as the structural aspects of LO, LOE, EP, AEPs, EPU and AEPUs were investigated by ¹H‐NMR and ¹³C‐NMR spectroscopic techniques, which also confirmed the incorporation of the acrylic monomers – AN and MMA – on the EP backbone Spectral analyses further demonstrated that, depending on its structure (substituent), each acrylic monomer follows a different grafting mechanism. Physico‐chemical characterization of AEPs and AEPUs was carried out by standard laboratory methods, and thermal analyses were accomplished by TGA and DSC. Physico‐mechanical characterization of AEPUs coatings further showed considerable improvement compared to the pristine (EPU) resin, due to the introduction of stiff acrylic moieties. The aforementioned studies as well as the coating characteristics of AEPU confirmed that AN and MMA have been incorporated in the EP backbone. These systems can be safely employed at up to 210–220 °C.     

Synthesis and characterization of homopolymer of 2-ethylhexyl acrylate and its copolymers with acrylamide,acrylonitrile, and methyl methacrylate

A homopolymer of 2-ethylhexyl acrylate (EHA) was synthesized by a free-radical solution polymerization technique. Copolymers of EHA with acrylonitrile (AN), acrylamide (AA), and methyl methacrylate (MMA) in various ratios were also synthesized by the same pro-cedure. These were characterized by PNMR, ¹³C-NMR, FTIR, GPC, and viscosity mea-surements. The reactivity ratios of various monomers were determined. The viscosity mea-surements were carried out in four different solvents: ethyl acetate (EA), methyl ethyl ketone (MEK), toluene (TL), and tetrahydrofuran (THF). The studies were done at three different temperatures of 30,35 and 40°C. The activation parameters of the viscous flow were computed for different systems. The intrinsic viscosity of the copolymers increased with temperature in MEK and EA. This trend showed reversal for the other two solvents. The results are discussed in detail. © 1996 John Wiley & Sons, Inc.     

Effect of N‐phenylmaleimide on a novel chemically bonded polymerizable photoinitiator comprising the structure of planar N‐phenylmaleimide and benzophenone for photopolymerization

A novel chemically bonded polymerizable photoinitiator 4‐[(4‐maleimido)phenoxy]benzophenone (MPBP) comprising the structure of planar N‐phenylmaleimide (NPMI) and benzophenone (BP), compared with the physical mixtures of NPMI/BP or NPMI/4‐hydroxybenzophenone, was investigated to disclose the mutual influence between NPMI and BP. A BP derivative, 4‐phenoxylbenzophenone, was selected as the model compound. Electron spin resonance spectra of such photoredox systems indicated MPBP and BP possess the same initiation mechanism. The large red‐shifted π–π* absorption of MPBP should be because of the phenoxyl group in MPBP but not the maleimide group. The photopolymerization of methyl methacrylate (MMA) and 1,6‐hexanediol diacrylate (HDDA) initiated by those systems, using the unsaturated tertiary amine N,N‐dimethylaminoethyl methacrylate (DMAEMA) as the coinitiator (H donor), was studied through dilatometry and photo‐differential scanning calorimetry. The results showed that MPBP was more efficient for the photopolymerization of MMA and HDDA than its physical mixture counterpart. The high efficiency of MPBP may be mainly because of the interaction between NPMI and BP group but not the phenoxyl group alone. A certain amount of NPMI can accelerate the photopolymerization when added to the formulations, but too much NPMI will eventually decrease the photoefficiency. Copyright © 2006 Society of Chemical Industry     

Grafting of acrylic monomers onto cotton fabric using an activated cellulose thiocarbonate–azobisisobutyronitrile redox system

The feasibility of a cellulose thiocarbonate–azobisisobutyronitrile (AIBN) initiation system to induce graft copolymerization of methyl methacrylate (MMA) and other acrylic monomers onto cotton fabric was investigated. Other acrylic monomers were acrylic acid, acrylonitrile, and methyl acrylate. The initiation system under investigation was highly activated in the presence of a metal‐ion reductant or a metal‐ion oxidant in the polymerization medium. A number of variables in the grafting reaction were studied, including AIBN concentration, pH of the polymerization medium, nature of substrate, monomer concentration, duration and temperature of polymerization, and composition of the solvent/water polymerization medium. The solvents used were methanol, isopropanol, 1,4‐dioxane, cyclohexane, benzene, dimethyl formamide, and dimethyl sulfoxide. There were optimal concentrations of AIBN (5 mmol/L), MMA (8%), Fe²⁺ (0.1 mmol/L), Mn²⁺ (8 mmol/L), and Fe³⁺ (2 mmol/L). A polymerization medium of pH 2 and temperature of 70°C constituted the optimal conditions for grafting. The methanol/water mixture constituted the most favorable reaction medium for grafting MMA onto cotton fabric by using the Fe²⁺–cellulose thiocarbonate–AIBN redox system. MMA was superior to other monomers for grafting. The unmodified cotton cellulose showed very little tendency to be grafted with MMA compared with the chemically modified cellulosic substrate. A tentative mechanism for the grafting reaction was proposed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1261–1274, 2004     

Effect of oxygen on intensity exponents of radiation-induced polymerization rates

Gamma radiation-induced graft polymerization to natural rubber in benzene solution (solution grafting), graft polymerization to natural rubber latex (Emulsion grafting), and emulsion polymerization of three vinyl monomers—styrene (St), methyl methacrylate (MMA) and acrylonitrile (AN), were carried out under air atmosphere to compare the radiation intensity exponent of each polymerization rate under air atmosphere with that under nitrogen atmosphere or under vacuum. The intensity exponents of the solution grafting both under air atmosphere and under exclusion of air were found to be numerals near one half. This indicates prevailing normal radical mechanism. However, the intensity exponents of the emulsion grafting under air atmosphere were found to be 0.94, 1.00, and 0.82 for St, MMA, and AN, respectively, and those of the emulsion polymerization under air atmosphere, 0.16 and 0.15 for St and MMA, respectively, although those of both emulsion grafting and emulsion polymerization under exclusion of air were found to be numerals near to one half except for that of emulsion polymerization of AN. For emulsion grafting, the initiating species is considered to be trunk polymer radical but the terminating species is assumed to be the radical(s) produced in the water phase in the presence of oxygen. For emulsion polymerization, both initiating and terminating species are assumed to be the radical(s) produced in the water phase in the presence of oxygen.     

Grafting onto wool. VII. Ceric ion-initiated graft copolymerization of vinyl monomers. Comparison of monomer reactivities

In an attempt to compare relative reactivities of vinyl monomers toward grafting, methyl methacrylate (MMA) and acrylic acid (AAc) were grafted separately to Himachali wool in aqueous medium by using ceric ammonium nitrate (CAN) as redox initiator. Nitric acid was found to catalyze the reaction. Percent grafting was determined as a function of concentration of nitric acid, concentration of CAN, concentration of monomer, time, and temperature. Optimum conditions for maximum grafting were evaluated for each monomer and were found to depend upon the nature of the monomer. Reactivities of MMA and AAc toward grafting were compared with those of methyl acrylate (MA), ethyl acrylate (EA), and vinyl acetate (VAc) reported earlier from this laboratory and were found to follow the order MA > EA > MMA > VAc > AAc. An explanation for the observed order of reactivity of different vinyl monomers is presented.     

Copolymers of acrylic acid with N‐vinylpyrrolidinone and 2‐hydroxyethyl methacrylate as pH‐responsive hydrogels synthesized through a photoinitiator‐free photopolymerization technique

pH‐sensitive hydrogels for biomedical applications were synthesized using a photoinitiator‐free technique involving the initiation of photopolymerization by donor/acceptor pairs. The differential photocalorimetric technique indicated a high polymerization rate for the N‐vinylpyrrolidinone (NVP, donor)/acrylic acid (AA, acceptor) pair at a 1:1 molar ratio. However, photopolymerization of larger quantities of these monomers (1:1 molar ratio) produced a water‐soluble polymer. Nevertheless, an anionic hydrogel was successfully formed when a small quantity of 2‐hydroxyethyl methacrylate (HEMA) was included in the NVP/AA formulation. A mixture of HEMA and AA, although both are classified as acceptors, photopolymerized to produce a copolymer which functioned as an anionic hydrogel. The swelling and drug release of these hydrogels were investigated in acidic, neutral and basic pH environments. Their biocompatibility with HaCaT human epidermal keratinocyte cells was tested and a positive cell growth as evidenced by the 3‐[4,5‐dimethylthiazol‐2‐yl]‐2,5‐diphenyl tetrazolium bromide (MTT) cell proliferation assay indicated that these hydrogels have no toxic effect on HaCaT. Copyright © 2006 Society of Chemical Industry     

PE氯化接枝St/AN共聚共混物研究

采用固相法对聚乙烯(PE)进行氯化接枝苯乙烯/丙烯腈(St/AN)单体,制得了改性氯化聚乙烯(CPE)材料。探讨了氯化反应温度、氯含量、引发剂过氧化苯甲酰(BPO)用量和单体配比对聚合物力学性能的影响,实验中还对PE接枝了不同单体,结果表明,采用二段温度(70℃,120℃)法,氯质量分数为35%,BPO加入质量为0.24g,m(St)/m(AN)为1:1时,可制得力学性能较好的CPE材料。极性单体MA、AN及St的加入提高了CPE材料的拉伸强度。     

Organotin polymers—XVII. Azeotropy in terpolymerization reactions of tri-n-butyltin 4-acryloyloxybenzoate wit alkyl acrylates or styrene and acrylonitrile

Ternary copolymerizations of tri-n-butyltin 4-acryloyloxybenzoate (ABTB) with acrylonitrile (AN) and alkyl acrylates [methyl (MA), ethyl (EA) or butyl acrylate (BA)], methyl methacrylate (MMA) or styrene (ST) were carried out in solution at 70°C in the presence of free radical initiator. Experimental terpolymerization data agreed well with calculations based on the Alfrey-Goldfinger equation. The determination of unitary, binary and ternary azeotropies of various systems studied was easily handled by a computer program. The results obtained show that there is no ternary azeotropic composition for any terpolymer, system studied. Selective unitary and binary azeotropic compositions were polymerized and the results obtained show good agreement between the theoretical and experimental terpolymer composition for each case.     

Synthesis and characterization of poly(methyl methacrylate)‐grafted silica microparticles

A procedure to synthesize poly(methyl methacrylate)‐grafted silica microparticles was developed by using radical photopolymerization of methyl methacrylate (MMA) initiated from N,N‐diethyldithiocarbamate (DEDT) groups previously bound to the silica surface (grafting “from”). The functionalization of silica microparticles with DEDT groups was performed in two steps: introduction of chlorinated functions onto the surface of silica particles, and then nucleophilic substitution of chlorines by DEDT functions via a S_N2 mechanism. The study was performed with a Kieselgel® S silica which was initially chlorinated in surface, either by direct chlorination of silanols with thionyl chloride, or by using a condensation reaction between silanols and a chlorofunctional trialkoxysilane reagent, 4‐(chloromethyl)phenyltrimethoxysilane and chloromethyltriethoxysilane, respectively. Three types of DEDT‐functionalized silica microparticles were prepared with a good control of the reactions, and then characterized by solid‐state ¹³C and ²⁹Si CP/MAS NMR. Their ability to initiate MMA photopolymerization was studied. The kinetics of MMA photopolymerization was followed by HPLC and ¹H‐NMR. Whatever the silica used the grafting progresses very slowly. On the other hand, the conversion of MMA in PMMA grafts is depending on the structure of the DEDT‐functionalized Kieselgel® S used. Poly(methyl methacrylate)‐grafted silica microparticles bearing high length grafts ( about 100) were synthesized. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Water as Blowing Agent: Preparation of Environmental Thermally Expandable Microspheres via Inverse Suspension Polymerization

Water-encapsulated environment-friendly core–shell thermally expandable microspheres (TEMs) were prepared via inverse suspension polymerization under atmospheric pressure. Acrylonitrile (AN), methyl methacrylic acid (MMA), and methacrylate (MA) were used as monomers, and water was used as the core material. The influences of dispersants, monomer feed ratio, and cross-linking agent on the TEMs were systematically investigated. The water could disperse well in the continuous oil phase employing both 6?g spand 80 and 0.2?g calcium stearate as dispersants. When the feed ratio of AN/MMA/MA was set at 1:2:2 and 1,4-butanediol dimethacrylate was used as cross-linking agent, TEMs possessed excellent properties. The properties of melamine resin foamed by TEMs-encapsulated water were better than that of n-octane and TEMs-encapsulated n-octane.     

A systematic study of tert-butylacrylamide-methyl acrylate-acrylic acid radical solution terpolymerization

Multi-functional polymers used for personal care products can be synthesized by radical polymerization of acrylic acid (AA) in alcohol/water solutions with non-functional monomers such as methyl acrylate (MA) and N-tert-butylacrylamide (t-BuAAm). However, solvents capable of forming or disrupting hydrogen bonds cause the polymerization kinetics of these monomers to deviate from their polymerization behaviour in bulk and non-polar solvents. In this work, a previous mechanistic model developed for MA/t-BuAAm copolymerization is extended to represent the terpolymerization system MA/t-BuAAm/AA. The additional kinetic coefficients required for the system are estimated from fitting to AA homopolymerizations and AA/MA and AA/t-BuAAm copolymerizations conducted in an ethanol/water solution. In-situ nuclear magnetic resonance (NMR) spectroscopy is used to follow monomer conversions and composition drift behaviour, with the molar mass distributions of the polymer products characterized by size-exclusion chromatography. Although AA is more reactive than MA in non-polar solvents, the reactivities of the two monomers equalize under the experimental conditions examined. Thus, the batch and semi-batch terpolymerization data collected are represented equally well by a reduced acrylate/t-BuAAm copolymerization model and the full terpolymerization implementation.