The usage of linseed oil‐based polyurethanes as a rheological modifier

Some oil‐based urethanes (urethane oils) were prepared from linseed oil, glycerol, and two types of diisocyanates, hexamethyle diisocyanate (HMDI) and 4,4′‐ diphenylmethane diisocyanate (MDI). These urethane oils were used as a rheological modifier in solvent‐based coatings. For this purpose the mixture prepared from urethane oil and alkyd resin (AR‐UO) was investigated in view of flow properties. Time dependence of AR‐UO was investigated by using the hysteresis loop method. None of the samples showed thixotropic flow behavior. The flow type was decided after calculation of the ratio of viscosity at low shear rate to viscosity at high shear rate. The results showed that HMDI‐based samples had the smallest viscosity ratio and increasing the amount of aromatic structure caused increasing shear thinning behavior. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1032–1035, 2005     

Rheological and mechanical properties of thermoplastic polyurethane elastomer derived from CO2 copolymer diol

CO₂ copolymer diol‐based thermal polyurethane elastomers (PPC‐TPU) were prepared by the reaction of CO₂ copolymer diol and methylene diphenyl diisocyanate and chain extender (ethylene glycol/1,4‐butanediol/1,6‐hexanediol) (EG/BDO/HG). The rheological and mechanical properties of PPC‐TPU were analyzed. The effects of shear rate, shear temperature, hard segment content, and variety of chain extender on the properties of PPC‐TPU were studied. The results showed that the apparent viscosity (η) of PPC‐TPU decreased with the increasing shear rate (τ), and the non‐Newtonian index (n) was less than 1. PPC‐TPU exhibited a typical character of pseudoplastic non‐Newtonian rheological behavior. The degradation during the processing was obviously inhibited by adding plasticizer and antioxidant. It was also discovered that the apparent viscosity varied with the content of hard segment and chain extender. Under the same temperature (185 °C) and shear rate (50 s^?1), the apparent viscosity increased considerably with the raise of hard segment content, and the apparent viscosity and tensile strength of PPC‐TPU with EG as chain extender was the maximum. It can be seen that with the apparent shear rate increasing, the variation tendency of apparent shear stress levels off, and the nonlinear relationship of τ–γ curve tended to be obvious. PPC‐TPU exhibited a typical character of pseudoplastic non‐Newtonian rheological behavior. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45974.     

Effect of structure modification on rheological properties of biodegradable poly(ester‐urethane)

Biodegradable lactic acid based poly(ester‐urethanes) (PEU) were polymerized and their structure and rheological properties were characterized. The polymerization process comprised two steps: lactic acid monomer was oligomerized to low molecular weight prepolymer, and this was then linked to high molecular weight PEU with chain extender, 1,6‐hexamethylene diisocyanate. The properties of PEU were modified by varying the amount of chain extender from 1.05:1 to 1.35:1 (NCO/OH ratio). The modification was mostly seen in the molecular weight distribution of the polymers, which was broadened from 2.2 to 3.5 as the amount of chain extender was increased. The telechelicity of the prepolymer was found to play an essential role in successful linking of the prepolymer units. In addition, the rheological properties of poly(ester‐urethane) were determined with capillary and dynamic rheometers. All PEU samples were pseudoplastic and broadening of their molecular weight distribution was accompanied by increased viscosity and complex viscosity at low shear rates and increased shear thinning. The temperature dependency of the measurement was pronounced. Rheological measurements also showed that PEU starts to degrade at 100°C and further rise in temperature increases the rate of degradation significantly.     

Synthesis and characterization of poly(urethane‐ester)s based on calcium salt of mono(hydroxybutyl)phthalate

Calcium‐containing poly(urethane‐ester)s (PUEs) were prepared by reacting diisocyanate (HMDI or TDI) with a mixture of calcium salt of mono(hydroxybutyl)phthalate [Ca(HBP)₂] and hydroxyl‐terminated poly(1,4‐butylene glutarate) [HTPBG₁₀₀₀], using di‐n‐butyltin‐dilaurate as catalyst. About six calcium‐containing PUEs having different composition were synthesized by taking the mole ratio of Ca(HBP)₂:HTPBG₁₀₀₀:diisocyanate (HMDI or TDI) as 3:1:4, 2:2:4, and 1:3:4. Two blank PUEs were synthesized by the reaction of HTPBG₁₀₀₀ with diisocyanate (HMDI or TDI). The polymers were characterized by IR, ¹H NMR, Solid state ¹³C‐CP‐MAS NMR, TGA, DSC, XRD, solubility, and viscosity studies. The T_g value of PUEs increases with increase in the calcium content and decreases with increase in soft segment content. The viscosity of the calcium‐containing PUEs increases with increase in the soft segment content and decreases with increase in the calcium content. X‐ray diffraction patterns of the polymers show that the HMDI‐based polymers are partially crystalline and TDI‐based polymers are amorphous in nature. The dynamic mechanical analysis of the calcium‐containing PUEs based on HMDI shows that with increase in the calcium content of polymer, modulus (g′ and g″) increases at any given temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1720–1727, 2006     

Microwave‐assisted rapid polycondensation reaction of 4‐(4′‐acetamidophenyl)‐1,2,4‐triazolidine‐3,5‐dione with diisocyanates

4‐(4′‐Aminophenyl)‐1,2,4‐triazolidine‐3,5‐dione was reacted with 1 mol of acetyl chloride in dry N,N‐dimethylacetamide (DMAc) at ?15°C and 4‐(4′‐acetamidophenyl)‐1,2,4‐triazolidine‐3,5‐dione [4‐(4′‐acetanilido)‐1,2,4‐triazolidine‐3,5‐dione] (APTD) was obtained in high yield. The reaction of the APTD monomer with excess n‐isopropylisocyanate was performed at room temperature in DMAc solution. The resulting bis‐urea derivative was obtained in high yield and was finally used as a model for the polymerization reaction. The step‐growth polymerization reactions of monomer APTD with hexamethylene diisocyanate, isophorone diisocyanate, and tolylene‐2,4‐diisocyanate were performed under microwave irradiation and solution polymerization in the presence of pyridine, triethylamine, or dibutyltin dilaurate as a catalyst. Polycondensation proceeded rapidly, compared with conventional solution polycondensation; it was almost completed within 8 min. The resulting novel polyureas had an inherent viscosity in the range of 0.07–0.17 dL/g in dimethylformamide or sulfuric acid at 25°C. These polyureas were characterized by IR, ¹H‐NMR, elemental analysis, and thermogravimetric analysis. The physical properties and structural characterization of these novel polyureas are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2103–2113, 2004     

Thiourethane thermoset coatings from bio‐based thiols

Three bio‐based thiols were synthesized via the thermal thiol‐ene reactions between sucrose soya ester (SSE) and multifunctional thiols; then, thiourethane coatings were produced from these thiols and their coating properties were studied. A series of high bio‐renewable content thiol oligomers were synthesized according to the previously reported thermal thiol‐ene reaction. Fourier transform infrared spectra (FTIR) confirmed the complete consumption of the double bonds in SSE, and gel permeation chromatography confirmed the formation of high‐molecular‐weight oligomers. The viscosity of these oligomers remained low due to their compact and branched structures. Thermoset thiourethane coatings were prepared from these thiol oligomers and polyisocyanate trimer resins with dibutyltin diacetate as the catalyst. FTIR spectra confirmed the formation of the thiourethane group. However, coatings based on isophorone diisocyanate (IPDI) polyisocyanate resin showed a lower degree of cure because of the decreased resin mobility due to the rigid cyclohexane ring. Generally, all the coatings showed good adhesion to aluminum panels, and had high gloss. However, they exhibited low tensile strength, modulus and chemical resistance due to the flexibility of the fatty acid chain. Coatings based on more rigid IPDI‐based polyisocyanate showed higher T_g, hardness and direct impact resistance compared with the hexamethylene‐diisocyanate (HDI) based polyisocyanate counterparts. Thermogravimetric analysis results showed that coatings based on mercaptanized soybean oil have better thermal stability than those from di‐pentene dimercaptan or glycol di‐3‐mercaptopropionate. Two T_g values were found by both differential scanning calorimetry and dynamic mechanical thermal analysis of thiourethanes from HDI‐based polyisocyanate and di‐pentene dimercaptan or glycol di‐3‐mercaptopropionate based oligomers due to phase separation resulting from the poor compatibility between HDI‐based polyisocyanate and the respective oligomers. Copyright © 2011 Society of Chemical Industry     

Layered silicate nanocomposites based on various high‐functionality epoxy resins. Part II: The influence of an organoclay on the rheological behavior of epoxy prepolymers

The effect of an organically surface modified layered silicate on the viscosity of various epoxy resins of different structures and different functionalities was investigated. Steady and dynamic shear viscosities of the epoxy resins containing 0–10 Wt% of the organoclay were determined using parallel plate rheology. Viscosity results were compared with those achieved through addition of a commonly used micronsized CaCO₃ filler. It was found that changes in viscosities due to the different fillers were of the same order, since the layered silicate was only dispersed on a micron‐sized scale in the monomer (prior to reaction), as indicated by X‐ray diffraction measurements. Flow activation energies at a low frequency were determined and did not show any significant changes due to the addition of organoclay or CaCO₃. Comparison between dynamic and steady shear experiments showed good agreement for low layered silicate concentrations below 7.5 wt%, i.e. the Cox‐Merz rule can be applied. Deviations from the Cox‐Merz rule appeared at and above 10 wt%, although such deviations were only slightly above experimental error. Most resin organoclay blends were well predicted by the Power Law model, only concentrations of 10 wt% and above requiring the Herschel‐Buckley (yield stress) model to achieve better fits. Wide‐angle X‐ray measurements have shown that the epoxy resin swells the layered silicate with an increase in the interlayer distance of approximately 15 Å, and that the rheology behavior is due to the lateral, micron‐size of these swollen tactoids.     

Synthesis and clay stabilization of a water‐soluble copolymer based on acrylamide,modular β‐cyclodextrin,and AMPS

A modular β‐cyclodextrin copolymer for clay stabilization was prepared from 2‐O‐(allyloxy‐2‐hydroxyl‐propyl)‐β‐cyclodextrin (XBH), acrylamide (AM), 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS), and sodium acrylate (NaAA) via redox free‐radical copolymerization. The effects of reactive conditions (such as initiator concentration, monomer ratio, reaction temperature, and pH) on the apparent viscosity of the copolymer were investigated and the optimal conditions for the copolymerization were established. The copolymer obtained was characterized by infrared spectroscopy, scanning electron microscope, viscosity measurements, rheological measurement, core stress test, and X‐ray diffractometry. The crystalline interspace of MMT could be reduced from 18.95323 Å to 15.21484 Å by copolymer AM/NaAA/AMPS/XBH. And this water‐soluble copolymer also showed remarkable anti‐shear ability, temperature resistance, and salt tolerance (1000 s^?1, viscosity retention rate: 35%; 120°C, viscosity retention rate: 75%; 10,000 mg/L NaCl, viscosity retention rate: 50.2%; 2000 mg/L CaCl₂, viscosity retention rate: 48.5%; 2000 mg/L MgCl₂, viscosity retention rate: 42.9%). © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Viscoelastic and adhesive properties of single‐component thermo‐resistant acrylic pressure sensitive adhesives

Poly(butyl acrylate‐vinyl acetate‐acrylic acid) based acrylic pressure sensitive adhesives (PSAs) were synthesized by solution polymerization for the fabrication of high performance pressure sensitive adhesive tapes. The synthesized PSAs have high shear strength and can be peeled off substrate without residues on the substrate at temperature up to 150°C. The PSAs synthesized in the present work are single‐component crosslinked and they can be used directly once synthesized, which is convenient for real applications compared to commercial multi‐component adhesives. The results demonstrated that the viscosity of the PSAs remained stable during prolonged storage. The effects of the preparation conditions such as initiator concentration, cross‐linker amount, organosiloxane monomer amount and tackifier resin on the polymer properties, such as glass transition temperature (T_g), molecular weight (M_w), surface energy and shear modulus, were studied, and the dependence of the adhesive properties on the polymer properties were also investigated. Crosslinking reactions showed a great improvement in the shear strength at high temperature. The addition of tackifier resin made peel strength increase compared to original PSAs because of the improvement of the adhesion strength. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40086.     

Comparison of nanoclay and carbon nanofiber particles on rheology of molten polystyrene nanocomposites under supercritical carbon dioxide

The effects of nanoparticles and high‐pressure carbon dioxide (CO₂) on shear viscosity of polystyrene (PS) were studied. Master curves of PS, PS + 5 wt % carbon nanofibers (CNFs), and PS + 5 wt % nanoclay (Southern Clay 20A) without CO₂ were created based on parallel‐plate measurements. The results showed that addition of nanoparticles increased the viscosity of the neat polymer. Steady‐state shear viscosity of PS in the presence of CO₂ and nanoparticles was measured by a modified Couette rheometer. The effect of supercritical CO₂ on these systems was characterized by shift factors. It was found that under the same temperature and CO₂ pressure, CO₂ reduced the viscosity less for both PS‐20A and PS‐CNFs than neat PS. Between the two types of nanoparticles, CNFs showed a larger viscosity reduction than 20A, indicating a higher CO₂ affinity for CNFs than 20A. However, the advantage of CNFs over 20A for larger viscosity reduction decreased with higher temperature. A gravimetric method (magnetic suspension balance) was used to measure the excess adsorption of CO₂ onto CNFs and nanoclay, thus, CO₂ showed a higher affinity for CNFs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Rheology and curing kinetics of fumed silica/cyanate ester nanocomposites

A low‐viscosity bisphenol E cyanate ester (BECy) monomer was combined with fumed silica with average primary particle diameters of 12 and 40 nm to form high‐temperature adhesives with processability at ambient temperatures. Rheological evaluation revealed that for silica loadings below 15 vol%, suspensions of both particle sizes exhibited shear thinning and thixotropic behavior. Samples with high silica loadings (>15 vol%) of 40‐nm silica also showed intense shear thickening at shear rates above 10 s^?1. Thixotropy was most pronounced for the 12‐nm silica, but the formation of a gel was slow, indicating that the polar nature of the BECy monomer was responsible for disrupting hydrogen bonds between silica particles. Rheokinetic evaluation of catalyzed samples showed that increasing silica content reduced gel time and increased gel viscosity, and this effect was most pronounced for the 12‐nm silica. Differential scanning calorimetry confirmed that the silica's hydroxyl groups have a minor catalytic effect on the polymerization kinetics, such that the activation energies of the catalyzed suspensions were decreased with increased nanoparticle loading and decreased particle size. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Polyurethanes with monodisperse rigid segments based on a diamine–diamide chain extender

Polyether(bisurethane‐bisurea‐bisamide)s (PEUUA) based on poly(tetramethylene oxide) (PTMO) were synthesized by chain extension of PTMO endcapped with a diisocyanate (DI), and a diamine–diamide extender. The prepolymers were PTMOs with molecular weights between 1270 and 2200 g mol^?1, either endcapped with 4,4′‐diphenylmethane diisocyanate (MDI), 2,4‐toluene diisocyanate (2,4‐TDI), or 1,6‐hexane diisocyante (HDI) and with a low content of free diisocyanate (<0.1 wt %). The diamine–diamide (6A6) extender was based on hexamethylene diamine (6) and adipic acid (A). In this way, segmented polyurethanes with monodisperse rigid segments (DI‐6A6‐DI) were obtained. The PEUUAs were characterized by DSC as well as temperature‐dependent FTIR and DMTA. The mechanical properties of the polymers were evaluated by compression set and tensile test measurements. The polyurethanes with monodisperse rigid segments displayed low glass transition temperatures, almost temperature‐independent rubbery plateaus and sharp melting temperatures. The crystallinities of the hard segments were 70–80% upon heating and 40–60% upon cooling. The rate of crystallization was moderately fast as the supercooling (T_m ? T_c) was in the order 36–54°C. The polyurethanes based on HDI had a much higher rubber modulus as compared to the MDI and 2,4‐TDI‐based polymers, because of a higher degree of crystallinity and/or a higher aspect ratio of the crystallites. The HDI residues are flexible and not sterically hindered and could therefore be more easily packed than MDI or 2,4‐TDI residues. Polyurethanes with monodisperse DI‐6A6‐DI hard segments have interesting properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermally stable polyurethane‐ureas and copolyurethane‐ureas containing zinc and nickel dihydroxysaltrien complexes

New 4,4′‐dihydroxysaltrien metal complexes, (MOHSal₂trien, where M = Zn and Ni) were synthesized and used for the synthesis of metal‐containing polyurethane‐ureas and copolyurethane‐ureas. MOHSal₂trien underwent polymerization reaction with two diisocyanates, namely 4,4′‐diphenylmethane diisocyanate (MDI) and isophorone diisocyanate (IPDI) to yield polyurethane‐ureas. Copolyurethane‐ureas were synthesized by the reaction between MOHSal₂trien, MDI, and diamines or dialcohols. The diamines or dialcohols employed were 4,4′‐methylenedianiline (MDA), hexamethylenediamine (HMA), bisphenol A (BPO), and hexamethylene glycol (HMO). The polymers were characterized by IR, NMR, elemental analysis, XRD, solubility, and viscosity. Thermal stability and flammability of polymers were studied by thermogravimetric analysis (TGA) in air and by measuring limiting oxygen index (LOI) values, respectively. It was found that the resulting metal‐containing polyurethane‐ureas and copolyurethane‐ureas exhibited good thermal stability. Among all metal‐containing polyurethane‐ureas, NiOHSal₂trien‐MDI was the most thermally stable polymer with char yield of 55% at 600°C. Solubility in DMSO of zinc‐containing copolyurethane‐ureas based on dialcohols was greatly improved when compared with those of zinc‐ and nickel‐containing polyurethane‐ureas. ZnOHSal₂trien‐MDI‐BPO and ZnOHSal₂trien‐MDI‐HMO gave high char yield of 46% at 600°C, which is almost comparable with that of NiOHSal₂trien‐MDI. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Rheology and processability of polyamide66 filled with different‐sized and size‐distributed calcium carbonate

Two‐sized calcium carbonates (CaCO₃) were blended and filled into polyamide66 (PA66). The shear viscosity of PA66/CaCO₃ composites was measured with a capillary extrusion rheometer. The results showed that the shear viscosity of the efficient size distribution samples (PA66 was filled with 600/2500 mesh CaCO₃ blending) obviously decreased compared with that of the single‐size distribution samples (PA66 was filled with 600 or 2500 mesh CaCO₃). The shear viscosity of PA66/CaCO₃ composites at different temperatures was also studied. The results showed that the flow activation energy and flow activation entropy of the efficient size distribution samples obviously increased compared with those of the single‐size distribution samples. The change in flow activation entropy was used to explain the experimental results of shear viscosity. The processability of PA66/CaCO₃ composites was evaluated with a HAAKE torque rheometer. The results showed that the processability of the efficient size distribution samples was obviously improved and the best efficiency of processability improvement appeared in the 30 wt% CaCO₃ content. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Soluble new optically active polyamides derived from 5‐(4‐methyl‐2‐phthalimidylpentanoylamino)isophthalic acid and different diisocyanates under microwave irradiation in molten ionic liquid

Ionic liquids (IL)s have been generating increasing attention over the last decade. ILs were originally introduced as alternative green reaction media owing to their distinctive chemical and physical properties of nonvolatility, nonflammability, thermal stability, and controlled miscibility. In this investigation, 5‐(4‐methyl‐2‐phthalimidyl‐pentanoylamino)isophthalic acid ( 6 ), as a bulky monomer, containing phthalimide and flexible chiral groups, has been synthesized. The direct polycondensation of this diacid monomer with several aromatic and aliphatic diisocyanates, such as 4,4′‐methylenebis(phenyl isocyanate), toluylene‐2,4‐diisocyanate, isophorone diisocyanate, and hexamethylene diisocyanate, was carried out in tetrabutylammonium bromide as a molten IL in the presence of different catalysts under microwave irradiation as well as conventional heating. The resulting polyamides (PA)s were characterized by FTIR and ¹H NMR spectroscopy, inherent viscosity measurements, thermal and elemental analysis. The obtained PAs showed high yields and moderate inherent viscosities in a range of 0.32–0.57 dL g⁻¹. The PAs were soluble in aprotic polar solvents. Thermogravimetric analysis showed that PAs are thermally stable, 10% weight loss temperatures in excess of 240 and 245°C, and char yields at 600°C in nitrogen higher than 14%. Since toxic and volatile solvent such as NMP was eliminated, this process was safe and green. It is very important to note that, because of high polarizability of ILs, they are very good solvents for absorbing microwaves. The combination of IL and microwave irradiation leads to large reductions in reaction times, very high heating rate with various benefits of the eco‐friendly approach, named green chemistry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis,characterization and thermal dissociation of 2‐butoxyethanol‐blocked diisocyanates and their use in the synthesis of isocyanate‐terminated prepolymers

A series of blocked diisocyanates has been synthesized from toluene diisocyante (TDI), isophorone diisocyanate (IPDI), hexamethylene diisocyanate (HDI), 4,4′‐diphenylmethane diisocyanate (MDI) and 2‐butoxyethanol. The synthesis of blocked diisocyanate adducts was confirmed by Fourier transform infrared, ¹H NMR, electron impact mass spectrometry and nitrogen analysis. Differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA) and carbon dioxide evolution were used to determine the minimum de‐blocking temperatures. De‐blocking temperatures determined by these three techniques were found to be in the order DSC > TGA > CO₂ evolution. The effect of different metal catalysts on thermal de‐blocking reaction of the blocked diisocyanates was studied, using the carbon dioxide evolution method. It was found that iron(III) oxide has the maximum catalytic activity on de‐blocking. The solubility of the blocked diisocyanate adducts was determined in different solvents. The study revealed that at 30 °C blocked IPDI and HDI adducts show better solubility than adducts based on TDI and MDI. Isocyanate‐terminated prepolymers of blocked diisocyanates and hydroxyl‐terminated polybutadiene (HTPB) were prepared. The storage stability and gelation times of the prepolymers were studied. Results showed that all the diisocyanate‐HTPB compositions are stable at 50 °C for more than three months. However, aliphatic diisocyanate‐HTPB compositions require greater gelation time than aromatic diisocyanate‐HTPB compositions at their respective de‐blocking temperatures. Copyright © 2007 Society of Chemical Industry     

Burning‐rate enhancement of a high‐energy rocket composite solid propellant based on ferrocene‐grafted hydroxyl‐terminated polybutadiene binder

Four different samples of ferrocene‐grafted hydroxyl‐terminated polybutadiene (Fc‐HTPB), containing 0.20, 0.52, 0.90, and 1.50 wt % iron, were synthesized by the Friedel–Crafts alkylation of ferrocene with hydroxyl‐terminated polybutadiene (HTPB) in the presence of AlCl₃ as a (Lewis acid) catalyst. The effects of the reaction conditions on the extent of ferrocene substitution were investigated. The Fc‐HTPBs were characterized by IR, ultraviolet–visible, ¹H‐NMR, and ¹³C‐NMR spectra. The iron content and number of hydroxyl groups were estimated, and the properties, including thermal degradation, viscosity, and propellant burning rates (BRs), were also studied. The thermogravimetric data indicated two major weight loss stages around 395 and 500°C. These two weight losses were due to the depolymerization and decomposition of the cyclized product, respectively, with increasing temperature. The Fc‐HTPB was cured with toluene diisocyanate and isophorone diisocyanate separately with butanediol–trimethylolpropane crosslinker to study their mechanical properties. Better mechanical properties were obtained for the gumstock of Fc‐HTPB polyurethanes with higher NCO/OH ratios. The BRs of the ammonium perchlorate (AP)‐based propellant compositions having these Fc‐HTPBs (without dilution) as a binder were much higher (8.66 mm/s) than those achieved with the HTPB/AP propellant (5.4 mm/s). © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Rheological characterization of concentrated cellulose solutions in 1‐allyl‐3‐methylimidazolium chloride

The rheological properties of high concentrated wood pulp cellulose 1‐allyl‐3‐methy‐limidazolium Chloride ([Amim]Cl) solutions were investigated by using steady shear and dynamic viscoelastic measurement in a large range of concentrations (10–25 wt %). The measurement reveals that cellulose may slightly degrade at 110°C in [Amim]Cl and the Cox–Merz rule is valid for 10 wt % cellulose solution. All of the cellulose solutions showed a shear thinning behavior over the shear rate at temperature from 80 to 120°C. The zero shear viscosity (η_o) was obtained by using the simplified Cross model to fit experimental data. The η_o values were used for detailed viscosity‐concentration and activation energy analysis. The exponent in the viscosity‐concentration power law was found to be 3.63 at 80°C, which is comparable with cellulose dissolved in other solvents, and to be 5.14 at 120°C. The activation energy of the cellulose solution dropped from 70.41 to 30.54 kJ/mol with an increase of concentration from 10 to 25 wt %. The effects of temperature and concentration on the storage modulus (G′), the loss modulus (G″) and the first normal stress difference (N₁) were also analyzed in this study. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Modification of a nicotinic acid functionalized water‐soluble acrylamide sulfonate copolymer for chemically enhanced oil recovery

N,N‐Diallyl nicotinamide (DANA) and acrylic acid (AA) were used to react with acrylamide (AM) and synthesize a novel nicotinic acid functionalized water‐soluble copolymer AM/AA/DANA by redox free‐radical polymerization. Then, the acrylamide/sodium acrylamido methanesulfonate/acrylic acid/N,N‐diallyl nicotinamide (AM/AMS/AA/DANA) was obtained by the introduction of the ? SO₃^? group into AM/AA/DANA after sulfomethylation. The optimal reaction conditions, such as the monomer ratio, initiator concentration, reaction temperature, and pH of the copolymerization or sulfomethylation, were investigated. Both AM/AA/DANA and AM/AMS/AA/DANA were characterized by IR spectroscopy, ¹H‐NMR, scanning electron microscopy, and intrinsic viscosity testing. We found that the AM/AMS/AA/DANA had a remarkable temperature tolerance (120°C, viscosity retention rate = 39.8%), shear tolerance (1000 s^?1, viscosity retention rate = 23.3%), and salt tolerance (10 g/L NaCl, 1.5 g/L MgCl₂, 1.5 g/L CaCl₂, viscosity retention rates = 37.4, 27.5, and 21.6%). In addition, the result of the core flood test showed that the about 13.1% oil recovery could be enhanced by 2.0 g/L AM/AMS/AA/DANA at 70°C. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40165.     

Effects of water on the long‐term properties of Bis‐GMA and silylated‐(Bis‐GMA) polymers

Bis‐GMA (2,2‐bis‐[4‐(2‐hydroxy‐3‐methacryloxypropoxy)phenyl]propane) is a viscous hygroscopic monomer which is used with triethyleneglycol‐dimethacrylate (TEGDMA) for dental restorations. Bis‐GMA was silylated with dimethyl‐isopropyl‐siloxane and further polymerized in order to increase water resistance and viscosity. The viscosity of the silylated monomer, Sil·Bis‐GMA, was 50 times lower than that of the parent monomer. After 1 month in water, poly(Bis‐GMA/TEGDMA) absorbed 2.6% water and the silylated polymer, poly(Sil·Bis‐GMA), only 0.56%. During this process water extracted residual monomer from each polymer. The behavior of water sorption and desorption as a function of time in poly(Sil·Bis‐GMA) was completely different from that shown by poly(Bis‐GMA/TEGDMA). The difference is discussed in terms of diffusion coefficients. Initially, water advancing contact angles (θ_ADV) were 75° and 95°, respectively. After 1 month in water both polymers showed a reduction of about 20° in θ_ADV. In poly(Bis‐GMA/TEGDMA), the reduction in θ_ADV obey to water absorption and bulk plasticization; it showed a reduction of 15°C in glass transition temperature, T_g. In contrast, the reduction in θ_ADV in poly (Sil·Bis‐GMA) obeyed to water adsorption and reorientation of the molecules at the surface in contact with the water phase; it only showed a change of 2°C in T_g. Contact angle hysteresis provided further evidence about plasticization. According to our results poly(Sil·Bis‐GMA) is more stable in water than poly(Bis‐GMA/TEGDMA). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008