Copolymerization of N‐aryl substituted itaconimide with methyl methacrylate: Effect of substituents on monomer reactivity ratio and thermal behavior

The article describes the synthesis and characterization of N‐(4‐methoxy‐3‐chlorophenyl) itaconimide (MCPI) and N‐(2‐methoxy‐5‐chlorophenyl) itaconimide (OMCPI) obtained by reacting itaconic anhydride with 4‐methoxy‐3‐chloroanisidine and 2‐methoxy‐5‐chloroanisidine, respectively. Structural and thermal characterization of MCPI and OMCPI monomers was done by using ¹H NMR, FTIR, and differential scanning calorimetry (DSC). Copolymerization of MCPI or OMCPI with methyl methacrylate (MMA) in solution was carried out at 60°C using AIBN as an initiator and THF as solvent. Feed compositions having varying mole fractions of MCPI and OMCPI ranging from 0.1 to 0.5 were taken to prepare copolymers. Copolymerizations were terminated at low percentage conversion. Structural characterization of copolymers was done by FTIR, ¹H NMR, and elemental analysis and percent nitrogen content was used to calculate the copolymer composition. The monomer reactivity ratios for MMA–MCPI copolymers were found to be r₁ (MMA) = 0.32 ± 0.03 and r₂ (MCPI) = 1.54 ± 0.05 and that for MMA–OMCPI copolymers were r₁ (MMA) = 0.15 ± 0.02 and r₂ (OMCPI) = 1.23 ± 0.18. The intrinsic viscosity [η] of the copolymers decreased with increasing mole fraction of MCPI/or OMCPI. The glass transition temperature as determined from DSC scans was found to increase with increasing amounts of OMPCI in copolymers. A significant improvement in the char yield as determined by thermogravimetry was observed upon copolymerization. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2391–2398, 2006     

Synthesis of amphiphilic poly(methyl methacrylate)‐block‐poly(methacrylic acid) diblock copolymers by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of 1‐(butoxy)ethyl methacrylate (BEMA) was carried out using CuBr/2,2′‐bipyridyl complex as catalyst and 2‐bromo‐2‐methyl‐propionic acid ester as initiator. The number average molecular weight of the obtained polymers increased with monomer conversion, and molecular weight distributions were unimodal throughout the reaction and shifted toward higher molecular weights. Using poly(methyl methacrylate) (PMMA) with a bromine atom at the chain end, which was prepared by ATRP, as the macro‐initiator, a diblock copolymer PMMA‐block‐poly [1‐(butoxy)ethyl methacrylate] (PMMA‐b‐PBEMA) has been synthesized by means of ATRP of BEMA. The amphiphilic diblock copolymer PMMA‐block‐poly(methacrylic acid) can be further obtained very easily by hydrolysis of PMMA‐b‐PBEMA under mild acidic conditions. The molecular weight and the structure of the above‐mentioned polymers were characterized with gel permeation chromatography, infrared spectroscopy and nuclear magnetic resonance. Copyright © 2005 Society of Chemical Industry     

Synthesis of well‐defined comb‐like amphiphilic copolymers with protonizable units in the pendent chains: 1. Preparation of narrow polydispersity copolymers of methyl methacrylate and 2‐hydroxyethyl methacrylate by atom‐transfer radical polymerization

Well‐defined methyl methacrylate (MMA) and 2‐(trimethylsiloxy)ethyl methacrylate (Pro‐HEMA) copolymers were prepared by atom‐transfer radical polymerization(ATRP), using CuCl/2,2′‐bipyridine as catalytic system and p‐toluenesulfonyl chloride as initiator. ATRP process of MMA and Pro‐HEMA was monitored by ¹H NMR, and the kinetic curves of the MMA/Pro‐HEMA copolymerization were plotted in terms of the ¹H NMR data. At low content of Pro‐HEMA in the feed composition, the copolymerization can be well controlled with the molecular weight, polydispersity and the monomer distribution in the copolymer chain. With the increase of Pro‐HEMA content in the feed mixture, the composition of the final copolymer deviates from the composition of the feed mixture gradually, and gradient copolymers of MMA/Pro‐HEMA can be obtained. Through the hydrolysis process, well‐defined copolymers of MMA/HEMA were obtained from poly(MMA/Pro‐HEMA). Copyright © 2003 Society of Chemical Industry     

Copolymerization and thermal behavior of methyl methacrylate with N‐(phenyl/p‐tolyl) itaconimides

This study describes the synthesis, characterization, and thermal behavior of copolymers of methyl methacrylate (MMA) and N‐p‐tolyl itaconimide (PTI)/N‐phenyl itaconimide (I). Homopolymerization and copolymerization of N‐(phenyl/p‐tolyl) itaconimide with MMA was carried out by use of various mole fractions of N‐aryl itaconimide in the initial feed from 0.1 to 0.5, using azobisisobutyronitrile as an initiator and tetrahydrofuran as the solvent. The copolymer composition was determined by ¹H‐NMR spectroscopy using the proton resonance signals attributed to –OCH₃ of MMA (δ = 3.5–3.8 ppm) and the aromatic protons (δ = 7.0–7.5 ppm) of N‐aryl itaconimide. The reactivity ratios of the monomers were found to be r₁ (PTI) = 1.33 ± 0.05/r₂ (MMA) = 0.24 ± 0.03 and r₁ (I) = 1.465 ± 0.035/r₂ (MMA) = 0.385 ± 0.005. The molecular weight of the copolymers decreased with increasing mole fraction of N‐aryl itaconimide in the copolymers. Glass‐transition temperature (T_g) and thermal stability of PMMA increased with increasing amounts of itaconimides in the polymer backbone. A significant increase in the percentage char yield at 700°C was observed on incorporation of a low mole fraction of N‐aryl itaconimides. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1195–1202, 2003     

Synthesis and characterization of PMMA‐b‐PBMA block copolymers by atom transfer radical polymerization

The synthesis of diblock copolymers using atom transfer radical polymerization, ATRP, of n‐butyl methacrylate, BMA, and methyl methacrylate, MMA, is reported. These copolymers were prepared from 2‐bromoisobutyryl‐terminated macroinitiators of poly(MMA) and poly(BMA), using copper chloride, CuCl,/N,N,N′,N″,N″‐pentamethyldiethylenetretramine, PMDETA, as the catalyst system, at 100°C in bulk and in benzonitrile solution. The block copolymers were characterized by means of size‐exclusion chromatography, SEC, and ¹H‐NMR spectroscopy. The SEC analysis of the synthesized diblock copolymers confirmed important differences in the molecular weight control depending on the reaction medium (solvent effect) and the chemical structure of the macroinitiator used. In addition, differential scanning calorimetry, (DSC) measurements were performed, showing for all the copolymers a phase separation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2683–2691, 2002     

Atom transfer radical copolymerization of methyl methacrylate with N‐cyclohexylmaleimide

Atom transfer radical polymerization has been applied to simultaneously copolymerize methyl methacrylate (MMA) and N‐cyclohexylmaleimide (NCMI). Molecular weight behaviour and kinetic study on the copolymerization with the CuBr/bipyridine(bpy) catalyst system in anisole indicate that MMA/NCMI copolymerization behaves in a ‘living’ fashion. The influence of several factors, such as temperature, solvent, initiator and monomer ratio, on the copolymerization were investigated. Copolymerization of MMA and NCMI in the presence of CuBr/bpy using cyclohexanone as a solvent instead of anisole displayed poor control. The monomer reactivity ratios were evaluated as r_NCMI = 0.26 and r_MMA=1.35. The glass transition temperature of the resulting copolymer increases with increasing NCMI concentration. The thermal stability of plexiglass could be improved through copolymerization with NCMI. © 2000 Society of Chemical Industry     

Synthesis and characterization of N‐acryloylcarbazole/methyl methacrylate copolymers

Copolymers of N‐acryloylcarbazole (A) and methyl methacrylate (M) were synthesized in different in‐feed ratios. The composition of the copolymer was determined by the help of ¹H NMR spectrum. The comonomer reactivity ratios determined by Kelen‐Tudos (KT) and nonlinear error‐in‐variables methods were r_A = 1.12 ± 0.16, r_M = 0.94 ± 0.14, and r_A = 1.05, r_M = 0.90, respectively. Complete spectral assignments of the ¹H and ¹³C ¹H NMR spectra of the copolymers were done by the help of distortionless enhancement by polarization transfer (DEPT) and two‐dimensional NMR techniques, such as heteronuclear single quantum coherence (HSQC), total correlation spectroscopy (TOCSY), and heteronuclear multiple bond correlation (HMBC). The methine, α‐methyl, and carbonyl carbon resonances were found to be sequence sensitive. The signals obtained were broad because of the restricted rotation of bulky carbazole group and the quadrupolar effect of nitrogen present in carbazole moiety. Glass transition temperatures (T_g) were determined by differential scanning calorimetry and were found to be characteristic of copolymer composition. As the N‐acryloylcarbazole content increases, the T_g increases from 378.3 K for poly(methyl methacrylate) to 430.4 K for poly(N‐acryloylcarbazole). Variation in T_g with the copolymer composition were found to be in good agreement with theoretical values obtained from Johnston and Barton equations. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2667–2676, 2006     

Synthesis of two‐end‐functionalized copolymer of styrene and methyl methacrylate via living radical polymerization

The random copolymers (HO‐P(St‐r‐MMA)‐COOH) of styrene (St) and methyl methacrylate (MMA) with hydroxyl group at one end and carboxyl group at another end were synthesized by nitroxide‐mediated living radical polymerization initiated by 4,4′‐azobis(4‐cyanovaleric acid) (ACVA) and 4‐hydroxyl‐2,2,6,6–tetramethylpiperidineoxyl (TEMPO‐OH). The experimental results have shown that all synthesized copolymers have narrow molecular weight distribution. The conversion of monomers and the molecular weight of copolymer increase with polymerization time. Thus, a copolymerization mechanism containing living radical polymerization is suggested. The use of this method permits the copolymer with two functional chain ends and controllable molecular weight as well as low molecular weight distribution. X‐ray photoelectron spectroscopy result shows that the synthesized copolymers can be tethered on the surface of silicon wafer through the reaction between the hydroxyl end of the copolymer and native oxide layer on the wafer. In addition, an organic/inorganic hybrid surface has achieved by treating copolymer tethered Si‐substrates with SiCl₄ vapor. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3118–3122, 2006     

Towards a one‐pot synthesis of a polystyrene–PMMA block copolymer via atom‐transfer radical polymerization

The solution atom‐transfer radical copolymerization of styrene and methyl methacrylate in butyl acetate at 110 °C in the presence of Cu(II) bromide and 2,2′‐bipyride was investigated. Polystyrene was polymerized by atom‐transfer radical polymerization using benzyl bromide as initiator and MMA was then added to the system. Block copolymers were formed when MMA was added at ≤90% styrene conversion. Molecular weight distributions (M_w/M_n) of the block copolymers were ≤1.5. The possibility of end‐capping the polystyrene precursor as a means of improving its initiating efficiency towards MMA was also investigated but did not improve the system. © 2002 Society of Chemical Industry     

Copolymerization of N‐(4‐carboxyphenyl) itaconimide or N‐(4‐carboxyphenyl) itaconamic acid with methyl methacrylate

This paper describes the synthesis and characterization of N‐(4‐carboxyphenyl) itaconamic acid (CPA) and N‐(4‐carboxyphenyl) itaconimide (CPI) obtained by reacting itaconic anhydride with p‐aminobenzoic acid. Structural and thermal characterization of CPA and CPI was done using ¹H‐NMR, FTIR, and differential scanning calorimetry (DSC). Copolymerization of CPA or CPI with methyl methacrylate (MMA) in solution was carried out at 60 °C using azobisisobutyronitrile as an initiator and dimethyl acetamide or THF as solvent. Feed compositions having varying mole fractions of CPA or CPI ranging from 0.05–0.20 or 0.1–0.5 were taken to prepare copolymers. Copolymerizations were terminated at low percentage conversion. Structural characterization of copolymers was done by ¹H‐NMR and elemental analysis. Copolymer composition was determined using percentage nitrogen content. The reactivity ratios were r₁ (MMA) = 0.68 ± 0.06 and r₂ (CPI) = 0.46 ± 0.06. The intrinsic viscosity [η] was determined using an Ubbelohde suspension level viscometer. [η] decreased with increasing mole fraction of N‐(p‐carboxyphenyl) itaconimide or N‐(p‐carboxyphenyl) itaconamic acid in copolymers. Glass transition temperature and thermal stability of the copolymers were determined using DSC and thermogravimetric analysis, respectively. The glass transition temperature (T_g) as determined from DSC scans increased with increasing amounts of CPA or CPI in copolymers. A significant improvement in the char yield was observed upon copolymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1909–1915, 2005     

Synthesis of poly(epichlorohydrin‐g‐methyl methacrylate) graft copolymers by the combination of cationic and atom transfer radical polymerization

Poly(epichlorohydrin) possessing chloromethyl side groups in the main chain was used in the atom transfer radical polymerization of methyl methacrylate and styrene to yield poly(epichlorohydrin‐g‐methyl methacrylate) and poly(epichlorohydrin‐g‐styrene graft copolymers. The polymers were characterized by ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, and fractional precipitation method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2725–2729, 2006     

Synthesis of polypropylene graft copolymers from a hydroxyl‐groups‐containing polypropylene precursor via atom‐transfer radical polymerization

Isotactic polypropylene graft copolymers, isotactic[polypropylene‐graft‐poly(methyl methacrylate)] (i‐PP‐g‐PMMA) and isotactic[polypropylene‐graft‐polystyrene] (i‐PP‐g‐PS), were prepared by atom‐transfer radical polymerization (ATRP) using a 2‐bromopropionic ester macro‐initiator from functional polypropylene‐containing hydroxyl groups. This kind of functionalized propylene can be obtained by copolymerization of propylene and borane monomer using isospecific MgCl₂‐supported TiCl₄ as catalyst. Both the graft density and the molecular weights of i‐PP‐based graft copolymers were controlled by changing the hydroxyl group contents of functionalized polypropylene and the amount of monomer used in the grafting reaction. The effect of i‐PP‐g‐PS graft copolymer on PP‐PS blends and that of i‐PP‐g‐PMMA graft copolymer on PP‐PMMA blends were studied by scanning electron microscopy. Copyright © 2006 Society of Chemical Industry     

Studies on the copolymerization of methyl methacrylate with N‐(o/m/p‐chlorophenyl) itaconimides

The article describes the synthesis and characterization of N‐aryl itaconimide monomers such as: N‐(p‐chlorophenyl) itaconimide (PI)/N‐(m‐chlorophenyl) itaconimide (MI)/N‐(o‐chlorophenyl) itaconimide (OI) and its copolymerization behavior with MMA. The homopolymers and copolymers of N‐aryl itaconimides and methyl methacrylate (MMA, M₂) were synthesized by varying the mol fraction of N‐aryl itaconimides in the initial feed from 0.1 to 0.5 using azobisisobutyronitrile (AIBN) as an initiator and tetrahydrofuran (THF) as the solvent. Copolymer composition was determined using ¹H‐NMR spectroscopy [by taking the ratio of intensities of signals due to ? OCH₃ of MMA (δ = 3.59 ppm) and the aromatic proton (δ = 7.2–7.5 ppm) of N‐aryl itaconimides] and percent nitrogen content. The reactivity ratios were found to be r₁ = 1.33 and r₂ = 0.36 (PI‐MMA) r₁ = 1.15 and r₂ = 0.32 (MI‐MMA) and r₁ = 0.81 and r₂ = 0.35 (OI‐MMA). Molecular weight as determined using high‐performance liquid chromatography decreased with increasing mol fraction of itaconimides in copolymers. All the polymers had a polydisperstivity index in the range of 1.5–2.6.Thermal characterization was done using differential scanning calorimetry and dynamic thermogravimetry in nitrogen atmosphere. Incorporation of these N‐aryl itaconimides in PMMA backbone resulted in an improvement in glass transition temperature (T_g) and thermal stability. Percent char increased with the increase of PI/MI/OI content in the copolymers. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2078–2086, 2001     

Surface‐initiated atom‐transfer radical polymerization (SI‐ATRP) of methyl methacrylate from carbon fibre

Surface modification of carbon fibre (CF) by well‐defined polymer brushes was carried out using the ‘grafting from’ method. Poly(methyl methacrylate)‐grafted carbon fibre (CF‐PMMA) was successfully prepared by surface‐initiated atom‐transfer radical polymerization (SI‐ATRP) of methyl methacrylate (MMA) from the macro‐initiator, bromo‐acetic ester‐modified carbon fibre (CF‐BrA), with the complex of 1,10‐phenanthroline and Cu(I)Br as catalyst. The percentage of grafting (PG%) and the conversion of monomer (C%) increased linearly with increasing of polymerization time, and reached 24.0 % and 6.7 %, respectively, after a polymerization time of 6 h, calculated from the elemental analyses (EA). The structural and surface morphological analyses were conducted with Fourier‐transform infrared (FTIR) spectroscopy, X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Copyright © 2005 Society of Chemical Industry     

New self‐crosslinkable copolymers based on N‐methyl‐N‐vinylbenzylpyrrolidinium halide and methyl methacrylate

Thermally‐induced self‐crosslinking behaviour has been found in copolymers containing N‐methyl‐N‐vinylbenzylpyrrolidinium chloride (MVBPC) and methyl methacrylate (MMA). NMR, IR and low molecular weight model reactions demonstrate that this crosslinking reaction occurs between the methyl ester groups of the MMA units and the quaternary ammonium salts, with the resulting benzyl esters forming chemical links between the MVBPC and MMA units with the formation of N,N‐dimethylpyrrolidinium chloride. Similar crosslinking behaviour has also been found when the Cl⁻ anion is replaced by Br⁻ and I⁻, but not in the case of BF as counter anion. © 2000 Society of Chemical Industry     

Atom transfer radical polymerization of methyl methacrylate initiated with a macroinitiator of poly(vinyl acetate)

Well‐defined poly(vinyl acetate‐b‐methyl methacrylate) block copolymers were successfully synthesized by the atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in p‐xylene with CuBr as a catalyst, 2,2′‐bipyridine as a ligand, and trichloromethyl‐end‐grouped poly(vinyl acetate) (PVAc–CCl₃) as a macroinitiator that was prepared via the telomerization of vinyl acetate with chloroform as a telogen. The block copolymers were characterized with gel permeation chromatography, Fourier transform infrared, and ¹H‐NMR. The effects of the solvent and temperature on ATRP of MMA were studied. The control over a large range of molecular weights was investigated with a high [MMA]/[PVAc–CCl₃] ratio for potential industry applications. In addition, the mechanism of the polymerization was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1089–1094, 2006     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis,characterizations and thermal behavior of methyl methacrylate and N‐(p‐carboxyphenyl) methacrylamide/acrylamide copolymers

The synthesis, characterization, and thermal properties of copolymers of methyl methacrylate (MMA) and N‐(p‐carboxyphenyl) methacrylamide/acrylamide (CPMA/CPA) are described. The copolymerization was carried out in solution by taking different mole fractions (0.1–0.5) of CPMA/CPA in the initial feed using azobisisobutyronitrile as an initiator and dimethylformamide as a solvent at 60°C. The copolymer composition was determined from ¹H‐NMR spectra by taking the ratio of the proton resonance signal due to the  OCH₃ of MMA (δ = 3.59 ppm) and the aromatic protons (δ = 7.6–7.8 ppm) of CPMA/CPA. The monomer reactivity ratios of MMA:CPMA and MMA:CPA were determined using the Fineman Ross and Kelen Tudos methods and were found to be 1.32 ± 0.01 [MMA], 1.11 ± 0.02 [CPMA], 2.60 ± 0.01 [MMA], and 0.20 ± 0.01 [CPA]. Incorporation of these comonomers in the MMA backbone resulted in an improvement in the glass‐transition temperature and thermal stability. The percent char also increased with the increase of CPMA/CPA content in the copolymers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 259–267, 2000